Search NASA⌕ Search

SEARCH · Search NASA

Results for “Hover Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

An Artificial Neural Network Approach to Predict Rotor-Airframe Acoustic Waveforms

A surrogate artificial neural network/machine learning model was developed to predict the acoustic interaction for a fixed-pitch rotor in proximity to a downstream cylindrical airframe typical of small Unmanned Aerial System (sUAS) platforms. The model was trained to predict the acoustic waveform under representative hover conditions as a function of rotational speed, airframe proximity, and observer angle. Training data were acquired in an anechoic chamber on both isolated rotors and rotor-airframe configurations. Acoustic amplitude and phase of the revolution-averaged interaction were predicted, which required up to 25 harmonics to capture the impulse event caused by the blade’s approach and departure from the airframe. Prediction performance showed, on average, that the models could estimate the acoustic amplitude and phase over the relevant harmonics for unseen conditions with 86% and 75% accuracy, respectively, enabling a time domain reconstruction of the waveform for the range of geometric and flow parameters tested.

acoustics↗
NASA NTRS1979

A flight investigation of performance and loads for a helicopter with NLR-1T main-rotor blade sections

Data on performance and rotor loads for a teetering-rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade-section contour are presented. The test envelope included hover, forward-flight speed sweeps from 35 to 85 m/sec, and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point described vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗
NASA NTRS1981

Pilot/vehicle model analysis of visual and motion cue requirements in flight simulation

The optimal control model for pilot/vehicle analysis is used to explore the effects of a CGI visual system and motion system dynamics on helicopter hover simulation fidelity. This is accomplished by expanding the perceptual aspects of the model to include motion sensing and by relating CGI parameters to information processing parameters of the model. Simulator fidelity is examined by comparing predicted performance and workload for flight with that predicted for various simulator configuration. The results of the analysis suggest that simulator deficiencies or a reasonable nature (by current standards) can result in substantial performance and/or workload infidelity. Both CGI and motion system effects are significant for this task. There is also a distinct interaction between the two sources of pilot cues. In particular, the presence of motion reduces the sensitivity to CGI limitations.

Lancraft, R.↗
NASA NTRS2015

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tilt Rotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity URANS solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade element model with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A 'quasi linear trim' was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 % to 0 % in the 80- by 120-Foot Wind Tunnel test section and -1.6 % to 4.8 % in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗
NASA NTRS2016

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tiltrotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity Unsteady Reynolds Averaged Navier-Stokes (URANS) solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade-element model (BEM) with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt, and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation, and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall, interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A "quasi linear trim" was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 to 0 percent in the 80- by 120-Foot Wind Tunnel and -1.6 to 4.8 percent in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity, and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗
NASA NTRS1977

Experimental investigations of thrust vectoring systems for VTOL aircraft

This paper presents a summary of two technology programs sponsored by NASA to investigate the characteristics of two thrust vectoring schemes for V/STOL aircraft. The operational capability of the VTOL aircraft is dependent on maximum utilization of the installed thrust in both the cruise and powered lift modes of flight. An effective thrust vectoring system on the cruise propulsion unit is therefore essential to provide maximum payload in hover and STOL plus minimum specific fuel consumption in loiter and cruise. Introducing a high by-pass ratio fan system, augmenting the gas generator thrust, as the propulsion system for VTOL aircraft places increased significance on the performance of the relatively short coupled thrust vectoring systems. The two programs discussed herein include both large-scale and small-scale tests of a vectoring hood system with a vented, internal-lip and swivel nozzle systems. These tests indicated that a satisfactory thrust vectoring system can be developed.

Rolls, L. S.↗
NASA NTRS1988

LANDER program manual: A lunar ascent and descent simulation

LANDER is a computer program used to predict the trajectory and flight performance of a spacecraft ascending or descending between a low lunar orbit of 15 to 500 nautical miles (nm) and the lunar surface. It is a three degree-of-freedom simulation which is used to analyze the translational motion of the vehicle during descent. Attitude dynamics and rotational motion are not considered. The program can be used to simulate either an ascent from the Moon or a descent to the Moon. For an ascent, the spacecraft is initialized at the lunar surface and accelerates vertically away from the ground at full thrust. When the local velocity becomes 30 ft/s, the vehicle turns downrange with a pitch-over maneuver and proceeds to fly a gravity turn until Main Engine Cutoff (MECO). The spacecraft then coasts until it reaches the requested holding orbit where it performs an orbital insertion burn. During a descent simulation, the lander begins in the holding orbit and performs a deorbit burn. It then coasts to pericynthion, where it reignites its engines and begins a gravity turn descent. When the local horizontal velocity becomes zero, the lander pitches up to a vertical orientation and begins to hover in search of a landing site. The lander hovers for a period of time specified by the user, and then lands.

Source record↗
NASA NTRS2009

Apollo Mission Techniques Lunar Orbit Activities - Part 1a

This slide presentation reviews the planned sequence of events and the rationale for all lunar missions, and the flight experiences and lessons learned for the lunar orbit activities from a trajectory perspective. Shown are trajectories which include the moon's position at the various stages in the complete trip from launch, to the return and reentry. Included in the presentation are objectives and the sequence of events,for the Apollo 8, and Apollo 10. This is followed by a discussion of Apollo 11, including: the primary mission objective, the sequence of events, and the flight experience. The next mission discussed was Apollo 12. It reviews the objectives, the ground tracking, procedure changes, and the sequence of events. The aborted Apollo 13 mission is reviewed, including the objectives, and the sequence of events. Brief summaries of the flight experiences for Apollo 14-16 are reviewed. The flight sequence of events of Apollo 17 are discussed. In summary each mission consistently performing precision landings required that Apollo lunar orbit activities devote considerable attention to: (1) Improving fidelity of lunar gravity models, (2) Maximizing availability of ground tracking, (3) Minimizing perturbations on the trajectory, (4) Maximizing LM propellant reserves for hover time. Also the use of radial separation maneuvers (1) allows passive re-rendezvous after each rev, but ... (2) sensitive to small dispersions in initial sep direction

Interbartolo, Michael A.↗
NASA NTRS2018

Generation of Mars Helicopter Rotor Model for Comprehensive Analyses

The present research is aimed at providing a performance model for the Mars Helicopter (MH), to understand the complexity of the flow, and identify future regions of improvement. The low density of the Martian atmosphere and the relatively small MH rotor, result in very low chord-based Reynolds number flows. The low density and Reynolds numbers reduce the lifting force and lifting efficiency, respectively. The high drag coefficients in subcritical flow, especially for thicker sections, are attributed to laminar separation from the rear of the airfoil. In the absence of test data, efforts have been made to explore these effects using prior very low Reynolds number research efforts. The rotor chord-based Reynolds number range is observed to be subcritical, which makes boundary layer transition unlikely to occur. The state of the two-dimensional rotor boundary layer in hover is approximated by calculating the instability point, laminar separation point, and the transition location to provide understanding of the flow state in the high Mach-low Reynolds number regime. The results are used to investigate the need for turbulence modeling in Computational Fluid Dynamics (CFD) calculations afterwards. The goal is to generate a performance model for the MH rotor for a free wake analysis, because the computational budget for a complete Navier-Stokes solution for a rotating body-fitted rotor is substantial. In this study, a Reynolds-Averaged Navier-Stokes (RANS) based approach is used to generate the airfoil deck using C81Gen with stitched experimental data for very high angles of attack. A full Grid Resolution Study is performed and over 4,500 cases are completed to create the full airfoil deck. The laminar separation locations are predicted within the accuracy of the approximate method when compared with the CFD calculations. The model is presented through airfoil data tables (c81 files) that are used by comprehensive rotor analysis codes such as CAMRADII, or the mid-fidelity CFD solver RotCFD. Finally, the rotor performance is compared with experimental data from the 25ft Space Simulator at the NASA Jet Propulsion Laboratory (JPL) and shows good correlation for the rotor Figure of Merit over the available thrust range.

Model↗
NASA NTRS1977

Tenth-scale powered model test of a tilt-nacelle V/STOL airplane

Wind tunnel and ground static tests of a tenth scale powered model of a lift/cruise fan airplane have been conducted to define its low speed performances and handling qualities. The model was powered by three 5.5-in diameter turbopowered simulators; one located in the forebody while the remaining two were installed in tilting nacelles mounted on the aft body. Results are presented for static hover tests in ground effects with the model configured for VTOL operations and at forward speeds with the model configured for loiter, short takeoff, and VTOL operations.

Omar, M. E.↗
NASA NTRS1984

Impact of flying qualities on mission effectiveness for helicopter air combat

Battlefield nap-of-the-earth (NOE) helicopter operations are vital for a use of the helicopter in a high-threat environment. As the pilot's workload in this flight regime is very high, the helicopter's handling qualities become an important factor. The present investigation is concerned with overall mission effectiveness, flying qualities, and their interaction with other parameters. A description is presented of a study which generated a significant amount of date relating the importance of flying qualities to the ability to perform several specific mission tasks. It was found that flying qualities do have a major impact on the ability to perform a specific mission. The impact of flying qualities on Scout helicopter mission effectiveness is mainly related to the probability of being detected. The flying qualities effect most critical to the Scout mission was found to be precision of hover control.

Harris, T. M.↗
NASA NTRS1990

Recent research results in stereo 3-D pictorial displays at Langley Research Center

Recent results from a NASA-Langley program which addressed stereo 3D pictorial displays from a comprehensive standpoint are reviewed. The program dealt with human factors issues and display technology aspects, as well as flight display applications. The human factors findings include addressing a fundamental issue challenging the application of stereoscopic displays in head-down flight applications, with the determination that stereoacuity is unaffected by the short-term use of stereo 3D displays. While stereoacuity has been a traditional measurement of depth perception abilities, it is a measure of relative depth, rather than actual depth (absolute depth). Therefore, depth perception effects based on size and distance judgments and long-term stereo exposure remain issues to be investigated. The applications of stereo 3D to pictorial flight displays within the program have repeatedly demonstrated increases in pilot situational awareness and task performance improvements. Moreover, these improvements have been obtained within the constraints of the limited viewing volume available with conventional stereo displays. A number of stereo 3D pictorial display applications are described, including recovery from flight-path offset, helicopter hover, and emulated helmet-mounted display.

Parrish, Russell V.↗
NASA NTRS1994

Techniques for designing rotorcraft control systems

Over the last two and a half years we have been demonstrating a new methodology for the design of rotorcraft flight control systems (FCS) to meet handling qualities requirements. This method is based on multicriterion optimization as implemented in the optimization package CONSOL-OPTCAD (C-O). This package has been developed at the Institute for Systems Research (ISR) at the University of Maryland at College Park. This design methodology has been applied to the design of a FCS for the UH-60A helicopter in hover having the ADOCS control structure. The controller parameters have been optimized to meet the ADS-33C specifications. Furthermore, using this approach, an optimal (minimum control energy) controller has been obtained and trade-off studies have been performed.

Yudilevitch, Gil↗
NASA NTRS2022

What would it take to manufacture perovskite solar cells in space?

Imagine, astronauts land on the moon. They verify their arrival with mission control, and perform system checks and validations. After the dust settles, they open the airlock of the landing vehicle and venture outside. A side hatch opens, and a flexible substrate slowly unfurls on a boom. A series of printer heads raster, hovering over the substrate and sequentially vapor-depositing the constituent layers of a perovskite solar module (Figure 1). In time, a 1-megawatt array has been manufactured on the moon and can now be connected to supply power to the Artemis Base Camp. This ambitious vision could someday become a reality. On August 29, 2021, a SpaceX Falcon 9 rocket launched a commercial resupply payload from Kennedy Space Center en route to the International Space Station (ISS). On board were perovskite solar cells that will fly for 6 months outside the ISS in low earth orbit (LEO) on the 15th Materials International Space Station Experiment (MISSE-15). This will be the first long duration flight of perovskite solar cell devices in LEO and a major step toward realizing the in-space operation and, potentially, manufacture of perovskite solar cells.

Lyndsey McMillon-Brown↗
NASA NTRS1986

Rotor/wing aerodynamic interactions in hover

An experimental and theoretical investigation of rotor/wing aerodynamic interactions in hover is described. The experimental investigation consisted of both a large-scale and small-scale test. A 0.658-scale, V-22 rotor and wing was used in the large-scale test. Wind download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter configuration). A wing with boundary-layer control was also tested to evaluate the effect of leading and trailing edge upper surface blowing on the wing download. A computationally efficient, semi-empirical theory was developed to predict the download on the wing. Finally, correlations between the theoretical predictions and test data are presented.

Felker, F. F.↗
NASA NTRS1986

Rotor/wing aerodynamic interactions in hover

An experimental and theoretical investigation of rotor/wing aerodynamic interactions in hover is described. The experimental investigation consisted of both a large-scale and small-scale test. A 0.658-scale, V-22 rotor and wing was used in the large-scale test. Wind download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter oonfiguration). A wing with boundary-layer control was also tested to evaluate the effect of leading and trailing edge upper surface blowing on the wing download. A computationally efficient, semi-empirical theory was developed to predict the download on the wing. Finally, correlations between the theoretical predictions and test data are presented.

Felker, F. F.↗
NASA NTRS1989

Helicopters and VTOL. I

Performance projections into the next half-century of VTOL aircraft design are presently made on the basis of recent design trends. Attention is given to the technology-development and commercial prospects for tilt-rotor, thrust-vectoring hover, lighter-than-air, and speculative electromagnetic-propulsion, remotely-beamed power systems. Highly automated air traffic control systems are envisioned which will incorporate AI, satellite positioning, synthetic vision, obstacle detection/avoidance and fiber-optic transmission to safely manage giant airborne mass-transit commuter systems. It is expected that tilt-rotor aircraft will become the dominant VTOL configuration as time passes.

Burks, John S.↗
NASA NTRS1992

Helmet Mounted Display symbology integration research

A five-week flight simulation investigation comparing screen/head stabilized Apache Helmet Mounted Display (HMD) flight symbology to world stabilized flight symbology is presented in this paper. Simulation test results indicate that pilots perform significantly (P is less than .05) better using world stabilized attitude symbology. They were accurate to an average of 1/2 deg at estimating terrain relief and aerial target locations. Pilots were able to take advantage of world referenced symbology due to the unique features of HMD that allow the pilot to visually use the symbology at extreme azimuth and elevation off-axis angles. Pilots preferred world stabilized symbology while performing contour flight tasks. They reported that the use of climb-dive-marker during contour flight greatly reduced pilot work load under conditions tested. A surprising number of cyclic input errors occurred when using both MIL-STD-1295 hover symbology and test symbology, indicating that a better approach for depicting hover symbology is probably warranted. The magnitude of cyclic input and spatial estimation errors increased as the off-axis viewing angle became larger.

Haworth, Loran A.↗