Search NASA⌕ Search

SEARCH · Search NASA

Results for “LUBRICATING OILS - VISCOSITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1949

Measurement of Oil-Film Pressures in Journal Bearings under Constant and Variable Loads

In a study of journal bearings, the measurement of the oil-film strength produces some significant information. A new instrument is described by means of which the pressure of the oil film in bearings (under constant or alternating load) can be measured and recorded. With this device, the pressure distribution in the lubricating film of a bearing bushing was measured (under different operating conditions on a journal bearing) in the pulsator-bearing-testing machine. These tests are described and discussed in the present report.

Buske, A.↗
NASA NTRS1984

Ground test challenges in the development of the Space Shuttle orbiter auxiliary power unit

A conventional aircraft hydraulic system design approach was selected to provide fluid power for the Space Shuttle Orbiter. Developing the power unit, known as the Auxiliary Power Unit (APU), to drive the hydraulic pumps presented a major technological challenge. A small, high speed turbine drive unit powered by catalytically decomposed hydrazine and operating in the pulse mode was selected to meet the requirement. Because of limitations of vendor test facilities, significant portions of the development, flight qualification, and postflight anomaly testing of the Orbiter APU were accomplished at the Johnson Space Center (JSC) test facilities. This paper discusses the unique requirements of attitude, gravity forces, pressure profiles, and thermal environments which had to be satisfied by the APU, and presents the unique test facility and simulation techniques employed to meet the ground test requirements. In particular, the development of the zero-g lubrication system, the development of necessary APU thermal control techniques, the accomplishment of integrated systems tests, and the postflight investigation of the APU lube oil cooler behavior are discussed.

Chaffee, N. H.↗
NASA NTRS1990

Experience with synthetic fluorinated fluid lubricants

Since the late 1970's, the wet lubricant of choice for space mechanisms has been one of the family of synthetic perfluoro polyalkylether (PFPE) compounds, namely Fomblin Z-25 (Bray-815Z) or DuPont's Krytox 143xx series. While offering the advantages of extremely low vapor pressures and wide temperature ranges, these oils and derived greases have a complex chemistry compared to the more familiar natural and synthetic hydrocarbons. Many aerospace companies have conducted test programs to characterize the behavior of these compounds in a space environment, resulting in a large body of hard knowledge as well as considerable space lore concerning the suitability of the lubricants for particular applications and techniques for successful application. The facts are summarized and a few myths about the compounds are dispelled, and some performance guidelines for the mechanism design engineer are provided.

Conley, Peter L.↗
NASA NTRS2004

Oil-Free Rotor Support Technologies for Long Life, Closed Cycle Brayton Turbines

The goal of this study is to provide technological support to ensure successful life and operation of a 50-300 kW dynamic power conversion system specifically with response to the rotor support system. By utilizing technical expertise in tribology, bearings, rotordynamic, solid lubricant coatings and extensive test facilities, valuable input for mission success is provided. A discussion of the history of closed cycle Brayton turboalternators (TA) will be included. This includes the 2 kW Mini-Brayton Rotating Unit (Mini-BRU), the 10kW Brayton Rotating Unit (BRU) and the 125 kW turboalternator-compressor (TAC) designed in mid 1970's. Also included is the development of air-cycle machines and terrestrial oil-free gas turbine power systems in the form of microturbines, specifically Capstone microturbines. A short discussion of the self-acting compliant surface hydrodynamic fluid film bearings, or foil bearings, will follow, including a short history of the load capacity advances, the NASA coatings advancements as well as design model advances. Successes in terrestrial based machines will be noted and NASA tribology and bearing research test facilities will be described. Finally, implementation of a four step integration process will be included in the discussion.

Lucero, John M.↗
NASA NTRS1991

On the solution of a lubrication problem with particulate solids

The lubrication characteristic of a fluid with solid particles is studied using the continuum theory of mixtures. The governing equations are formulated and appropriate boundary conditions are introduced for an arbitrary-shaped lubricant film thickness. As a special case, closed-form analytical perturbation solutions for pressure and shear stress are obtained for a mixture of a conventional oil and solid particles with small values of solid-volume fraction sheared in the clearance space of an infinitely long slider bearing. It is found that when compared with a pure fluid, the mixture of the fluid and solid generates a higher pressure and therefore a higher load-carrying capacity with the added advantage of a reduction in the coefficient of friction.

Dai, F.↗
NASA NTRS1999

Performance and Durability of High Temperature Foil Air Bearing for Oil-Free Turbomachinery

The performance and durability of advanced, high temperature foil air bearings are evaluated under a wide range (10-50 kPa) of loads at temperatures from 25 to 650 C. The bearings are made from uncoated nickel based superalloy foils. The foil surface experiences sliding contact with the shaft during initial start/stop operation. To reduce friction and wear, the solid lubricant coating, PS304, is applied to the shaft by plasma spraying. PS304, is a NiCr based Cr2O3 coating with silver and barium fluoride/calcium fluoride solid lubricant additions. The results show that the bearings provide lives well in excess of 30,000 cycles under all of the conditions tested. Several bearings exhibited lives in excess of 100,000 cycles. Wear is a linear function of the bearing load. The excellent performance measured in this study suggests that these bearings and the PS304 coating are well suited for advanced high temperature, oil-free turbomachinery applications.

DellaCorte, C.↗
NASA NTRS2000

Performance and Durability of High Temperature Foil Air Bearings for Oil-Free Turbomachinery

The performance and durability of advanced, high temperature foil air bearings are evaluated under a wide range (10-50 kPa) of loads at temperatures from 25 to 650 C. The bearings are made from uncoated nickel based superalloy foils. The foil surface experiences sliding contact with the shaft during initial start/stop operation. To reduce friction and wear, the solid lubricant coating, PS304, is applied to the shaft by plasma spraying. PS304 is a NiCr based Cr2O3 coating with silver and barium fluoride/calcium fluoride solid lubricant additions. The results show that the bearings provide lives well in excess of 30,000 cycles under all of the conditions tested. Several bearings exhibited lives in excess of 100,000 cycles. Wear is a linear function of the bearing load. The excellent performance measured in this study suggests that these bearings and the PS304 coating are well suited for advanced high temperature, oil-free turbomachinery applications.

DellaCorte, C.↗
NASA NTRS1984

Operating characteristics of a three-piece-inner-ring large-bore roller bearing to speeds of 3 million DN

A 118 mm bore roller bearing with a three piece inner ring ran successfully at 300,000 DN for 20 hr. Provisions were made for lubrication and cooling through the inner ring. In some tests the outer ring was also cooled. Power loss within the bearing increased with both speed and total oil flow rate to the inner ring. Outer ring temperature decreased by as much as 22 K (40 F) when outer ring cooling was employed whereas inner ring temperature remained essentially constant. Cage slip was greatly reduced or even eliminated by using a bearing with a very tight clearance at operating speed. A three piece inner ring bearing had higher inner ring temperatures and less temperature difference between the inner and outer rings than a conventional one piece inner ring bearing.

Schuller, F. T.↗
NASA NTRS1975

Evaluation of a series hybrid thrust bearing at DN values to three million. 2: Fabrication and testing

Results of tests made to determine the experimental performance of a series hybrid bearing are reported. The bearing consists of a 150 mm ball bearing and a centrifugally actuated, conical, fluid film bearing fitting an envelope with an outer radius of 86.4 mm (3.4 in.) and inner radius of 71 mm (2.8 in.). Tests were conducted up to 16,500 rpm, at which speed an axial load of 15,568 N (3500 lb) was safely supported by the hybrid bearing system. Through the employment of the series hybrid bearing principle, it was possible to reduce the effective ball bearing speed to approximately one-half of the shaft speed. A reduction of this magnitude should result in a tenfold increase in the ball bearing fatigue life. A successful simulation of fluid film bearing lubricant supply failure, performed repeatedly at an operating speed of 10,000 rpm, resulted in complete and smooth change over to full scale ball bearing operation when the oil supply to the fluid film bearing was discontinued. Reactivation of the fluid film supply system produced a flawless return to the original mode of hybrid operation.

Eusepi, M.↗
DOE OSTI2021

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗
NASA NTRS1975

What is EHD

The life of many highly loaded machine elements relies on the formation of a very thin elastohydrodynamic (EHD) oil film between surfaces in motion. Its formation results from the combination of a remarkable set of circumstances rarely appreciated. This article endeavors to explain the mechanism of elastohydrodynamic lubrication with simple physical concepts that are easy to understand.

Wedeven, L. D.↗
NASA NTRS1980

Effect of cage design on characteristics of high-speed-jet-lubricated 35-millimeter-bore ball bearing

Parametric tests were conducted with a 35 mm bore angular contact ball bearing with a double outer land guided cage. Provisions were made for jet lubrication and outer-ring cooling of the bearing. Test conditions included a combined thrust and radial load at nominal shaft speeds of 48,000 rpm, and an oil-in temperature of 394 K (250 F). Successful operation of the test bearing was accomplished up to 2.5 million DN. Test results were compared with those obtained with similar bearing having a single outer land guided cage. Higher temperatures were generated with the double outer land guided cage bearing, and bearing power loss and cage slip were greater. Cooling the outer ring resulted in a decrease in overall bearing operating temperature.

Schuller, F. T.↗
NASA NTRS1964

Studies of Lubricating Materials in Vacuum

Lubricating materials for use in a vacuum environment have been the subject of a series of experimental investigations. Evaporation properties were evaluated for solid polymeric compositions. Friction and wear studies explored the behavior during sliding contact for series of polymeric compositions, binary alloys containing soft film-forming phases, complex alloys with film-forming materials, and a burnished MoS2 film. Friction and wear experiments were conducted at 10(exp-9)mm Hg with a 3/16-inch-radius-hemisphere rider specimen sliding on the flat surface of a rotating 2-1/2-inch-diameter disk specimen with materials that had low rates of evaporation. The influence of fillers in polytetrafluoroethylene (PTFE) on decomposition during vacuum friction studies was determined with a mass spectrometer. A real advantage in reducing decomposition and improving friction wear properties is gained by adding fillers (e.g., copper) that improve thermal conductivity through the composite materials. A polyimide and an epoxy-MoS2 composition material were found to have better friction and wear properties than PTFE compositions. A series of alloys (cast binary as well as more complex alloys) that contained microinclusions of potential film-forming material was studied. These materials replaced the normal surface oxides as they were worn away on sliding contact. Iron sulfide, nickel oxide, and tin are typical film-forming materials employed and were demonstrated to be effective in inhibiting surface welding and reducing friction. A burnished MoS2 film applied to type 440-C stainless steel in argon with a rotating soft wire brush had good endurance properties but somewhat higher friction than commercially available bonded films. An oil film applied to the burnished MoS2 markedly reduced its endurance life.

WEAR↗
DOE OSTI2020

In situ multimodal imaging for nanoscale visualization of tribofilm formation

A third of the energy from fuel combustion in passenger car gasoline engines is lost due to friction. Carefully designed engine lubricants can recover some of these losses by reducing friction and wear by forming a nanometer-scale chemico-physico tribofilm between surfaces. Accordingly, attention has focused on developing oil formulations that form low-friction tribofilms. However, analyses of resultant tribofilms are typically conducted after tribo-tests with conventional characterization tools and do not offer insights into tribofilm formation and evolution, precluding information critical to tuning tribofilm properties. In this work, we developed a unique multimodal methodology based on Atomic Force Microscopy (AFM) with local probe heating for in situ tribological studies that activates friction modifiers and simultaneously captures the evolution of friction and surface roughness, with nanometer resolution. As a platform to demonstrate the ability of this methodology to visualize dynamics of tribofilm formation in situ, we apply it to molybdenum-based friction modifiers to distinguish key factors in their functionality and correlate nanoscale AFM and Friction Force Microscopy data to bench tribo-tests used in the industry. To decode the formation mechanisms observed in situ and underlying chemistry of tribofilms, we performed ab initio Molecular Dynamics (AIMD) simulations at comparable conditions. AIMD simulations confirmed both nanoscale and bench tribo-test results and showed deviations in molecular organization in tribofilms that are formed from different molybdenum-based friction modifiers that corroborates with surface functionality. With this innovative methodology, we demonstrate proof-of-principle in situ formation of molybdenum-based tribofilms directly on steel surfaces that could be applied generally to studying tribofilm formation.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Design and evaluation of a 3 million DN series-hybrid thrust bearing

The bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, was fatigue tested. Test conditions were representative of a mainshaft ball bearing in a gas turbine engine operating at maximum thrust load to simulate aircraft takeoff conditions. Tests were conducted up to 16000 rpm and at this speed an axial load of 15568 newtons (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. It was concluded that a speed reduction of this magnitude results in a ten-fold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system resulted in a flawless return to the original mode of hybrid operation.

Scibbe, H. W.↗
NASA NTRS1976

Design and evaluation of a 3 million DN series-hybrid thrust bearing

The design and experimental evaluation of a series-hybrid thrust bearing, consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid-film bearing, is presented. Tests were conducted up to 16,000 rpm and at this speed an axial load of 15,600 N (3500 lb) was safely supported by the hybrid bearing system. Through the series-hybrid bearing principle, the effective ball bearing speed was reduced to approximately one-half of the shaft speed. A speed reduction of this magnitude would result in a tenfold increase in the ball bearing fatigue life. A successful evaluation of fluid-film bearing lubricant supply failure was performed repeatedly at an operating speed of 10,000 rpm. A complete and smooth changeover to full-scale ball bearing operation was effected when the oil supply to the fluid-film bearing was cut off. Reactivation of the fluid-film oil supply system produced a flawless return to the original mode of hybrid operation.

Scibbe, H. W.↗
NASA NTRS1974

Design, fabrication, and operation of a test rig for high-speed tapered-roller bearings

A tapered-roller bearing test machine was designed, fabricated and successfully operated at speeds to 20,000 rpm. Infinitely variable radial loads to 26,690 N (6,000 lbs.) and thrust loads to 53,380 N (12,000 lbs.) can be applied to test bearings. The machine instrumentation proved to have the accuracy and reliability required for parametric bearing performance testing and has the capability of monitoring all programmed test parameters at continuous operation during life testing. This system automatically shuts down a test if any important test parameter deviates from the programmed conditions, or if a bearing failure occurs. A lubrication system was developed as an integral part of the machine, capable of lubricating test bearings by external jets and by means of passages feeding through the spindle and bearing rings into the critical internal bearing surfaces. In addition, provisions were made for controlled oil cooling of inner and outer rings to effect the type of bearing thermal management that is required when testing at high speeds.

Signer, H. R.↗
NASA NTRS1978

Traction and lubricant film temperature as related to the glass transition temperature and solidification

Does a traction fluid have to be a glass or solid under operating conditions. Infrared spectra on dynamic EHD contacts of several types of fluid were used to determine the surface and oil-film temperatures. Polarized spectral runs were made to study molecular alignment. Static glass transition pressures at appropriate temperatures were between 0.1 and 2.0 GPa, with the traction fluid showing the highest. In the EHD contact region, the traction fluid showed both the highest film temperatures as well as the greatest degree of molecular alignment. A plot of the difference between the film and surface temperatures vs shear rate resulted in a master plot valid for all the fluids. From this work, the authors propose a model of 'fluid' traction, where friction between parallel rough molecules provides the traction.

Lauer, J. L.↗