Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETIC BALANCES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

The Low-Recycling Lithium Boundary and Implications for Plasma Transport

Pumping of incident hydrogen and impurity ions by lithium enables control of the particle inventory and fueling profile in magnetic-confined plasmas, and may raise the plasma temperature near the wall. As a result, the density gradient is expected to contribute substantially to the free-energy, affecting particle and thermal transport from micro-turbulence which is typically the dominant transport mechanism in high-temperature fusion experiments. Transport in gyrokinetic simulations of density-gradient-dominated profiles is characterized by a small linear critical gradient, large particle flux, and preferential diffusion of cold particles. As a result, the heat flux is below 5/2 or even 3/2 times the particle flux, usually assumed to be the minimum for convection. While surprising, this result is consistent with increasing entropy. Coupled TEM-ITG (ion-temperature- gradient) simulations using ηe = ηi find η = ∇T /∇n∼0.8 maximizes the linear critical pressure gradient, which suggests that experiments operating near marginal ITG stability with larger η would increase the linear critical pressure gradient by transferring free-energy from the temperature gradient to the density gradient. Simulations were performed with profiles predicted for the Lithium Tokamak Experiment (LTX) if ion thermal transport was neoclassical, while electron thermal transport and particle transport were a fixed ratio above the neoclassical level. A robust TEM instability was found for the outer half radius, while the ITG was found to be driven unstable as well during gas puff fueling. This suggests that TEM transport will be an important transport mechanism in high-temperature low-recycling fusion experiments, and in the absence of stabilizing mechanisms, may dominate over neoclassical transport. A diagnostic suite has been developed to measure hydrogen and impurity emission in LTX in order to determine the lower bound on recycling that can be achieved in a small tokamak using solid lithium coatings, assess its dependence on the operating condition of the lithium surface, and evaluate its impact on the discharge. Coatings on the close-fitting stainless-steel substrate produce a significant reduction in recyling, so that the effective particle confinement times are as low as 1 ms. Measurements of particle inventory in the plasma and hydrogen Lyman-α emission indicate that hydrogen recycling at the surface increases as subsequent discharges are performed; nevertheless, strong pumping of hydrogen is observed even after almost double the cumulative fueling is applied that should saturate the lithium coating to the penetration depth of hydrogen ions. Probe measurements show that when external fueling is terminated, the scrape-off-layer of discharges with fresh coatings decays to lower density and rises to higher electron temperature than for discharges with a partially-passivated surface, consistent with reduced edge cooling from recycled particles. Near the end of the discharge, higher plasma current correlates with reduced τp * and hydrogen emission, suggesting that discharges with fresh coatings achieve higher electron temperature in the core. A novel approach using neutral modeling was developed for the inverse problem of determining the distribution of recycled particle flux from PFC surfaces given a large number of emission measurements, revealing that extremely low levels of recycling (Rcore∼0.6 and Rplate∼0.8) have been achieved with solid lithium coatings. Together with impurity emission measurements, modeling suggests that during periods of particularly low electron density, influx of impurities from the walls contributes substantially to the global particle balance.

magnetic confinement↗

ENERGETIC PARTICLE DIFFUSION IN CRITICALLY BALANCED TURBULENCE

Observations and modeling suggest that the fluctuations in magnetized plasmas exhibit scale-dependent anisotropy, with more energy in the fluctuations perpendicular to the mean magnetic field than in the parallel fluctuations and the anisotropy increasing at smaller scales. The scale dependence of the anisotropy has not been studied in full-orbit simulations of particle transport in turbulent plasmas so far. In this paper, we construct a model of critically balanced turbulence, as suggested by Goldreich and Sridhar, and calculate energetic particle spatial diffusion coefficients using full-orbit simulations. The model uses an enveloped turbulence approach, where each two-dimensional wave mode with wavenumber k is packed into envelopes of length L following the critical balance condition, L{proportional_to}k {sup -2/3} , with the wave mode parameters changing between envelopes. Using full-orbit particle simulations, we find that both the parallel and perpendicular diffusion coefficients increase by a factor of two, compared to previous models with scale-independent anisotropy.

79 ASTRONOMY AND ASTROPHYSICS↗

Fuel recycling control in long pulse operation with full tungsten divertors in EAST tokamak

Fuel recycling control in long pulse discharges is studied in EAST tokamak with tungsten divertors by particle balance. Double null configuration, proper Resonant Magnetic Perturbation (RMP), divertor cryopumps and realtime lithium injection, are all very effective for recycling control. High heating power discharge leads to low recycling due to the enhancement of particle exhausting. High external gas injection is required in a low fuel recycling discharge to keep a constant density, and Dα emission is increased by external injection, therefore a higher Dα emission may indicate low fuel recycling for the same plasma density. Reproducible long pulse discharges of over 100 s with core electron temperature >10 keV, and 1056 s discharge with ~1.5 MW heating power were obtained in the EAST 2021 campaign, fuel recycling was well controlled by divertor cryopumps and realtime lithium injection. The results provide a valuable reference for the high power and long pulse operation in future fusion reactors, such as ITER and CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

PLASMOID RELEASES IN THE HELIOSPHERIC CURRENT SHEET AND ASSOCIATED CORONAL HOLE BOUNDARY LAYER EVOLUTION

As the heliospheric current sheet (HCS) is corotating past STEREO-B, near-Earth spacecraft ACE, Wind and Cluster, and STEREO-A over more than three days between 2008 January 10 and 14, we observe various sections of (near-pressure-balanced) flux-rope- and magnetic-island-type plasmoids in the associated heliospheric plasma sheet (HPS). The plasmoids can qualify as slow interplanetary coronal mass ejections and are relatively low proton beta (<0.5) structures, with small length scales (an order of magnitude lower than typical magnetic cloud values) and low magnetic field strengths (2-8 nT). One of them, in particular, detected at STEREO-B, corresponds to the first reported evidence of a detached plasmoid in the HPS. The in situ signatures near Earth are associated with a long-decay X-ray flare and a slow small-scale streamer ejecta, observed remotely with white-light coronagraphs aboard STEREO-B and SOHO and tracked by triangulation. Before the arrival of the HPS, a coronal hole boundary layer (CHBL) is detected in situ. The multi-spacecraft observations indicate a CHBL stream corotating with the HCS but with a decreasing speed distribution suggestive of a localized or transient nature. While we may reasonably assume that an interaction between ejecta and CHBL provides the source of momentum for the slow ejecta's acceleration, the outstanding composition properties of the CHBL near Earth provide here circumstantial evidence that this interaction or possibly an earlier one, taking place during streamer swelling when the ejecta rises slowly, results in additional mixing processes.

79 ASTRONOMY AND ASTROPHYSICS↗

On the non-existence of stepped-pressure equilibria far from symmetry

The Stepped Pressure Equilibrium Code (SPEC) (Hudson et al 2012 Phys. Plasmas 19 112502) has been successful in the construction of equilibria in 3D configurations that contain a mixture of flux surfaces, islands and chaotic magnetic field lines. In this model, the plasma is sliced into sub-volumes separated by ideal interfaces, and in each volume the magnetic field is a Beltrami field. In the cases where the system is far from possessing a continuous symmetry, such as in stellarators, the existence of solutions to a stepped-pressure equilibrium with given constraints, such as a multi-region relaxed MHD minimum energy state, is not guaranteed but is often taken for granted. Using SPEC, we have studied two different scenarios in which a solution fails to exist in a slab with analytic boundary perturbations. Here we found that with a large boundary perturbation, a certain interface becomes fractal, corresponding to the break up of a Kolmogorov–Arnold–Moser (KAM) surface. Moreover, an interface can only support a maximum pressure jump while a solution of the magnetic field consistent with the force balance condition can be found. An interface closer to break-up can support a smaller pressure jump. We discovered that the pressure jump can push the interface closer to being non-smooth through force balance, thus significantly decreasing the maximum pressure it can support. Our work shows that a convergence study must be performed on a SPEC equilibrium with interfaces close to break-up. These results may also provide insights into the choice of interfaces and have applications in finding out the maximum pressure a machine can support.

3D equilibrium↗

Warp simulations for capture and control of laser-accelerated proton beams

The capture of laser-accelerated proton beams accompanied by co-moving electrons via a solenoid field has been studied with particle-in-cell simulations. The main advantages of the Warp simulation suite that was used, relative to envelope or tracking codes, are the possibility of including all source parameters energy resolved, adding electrons as second species and considering the non-negligible space-charge forces and electrostatic self-fields. It was observed that the influence of the electrons is of vital importance. The magnetic effect on the electrons out balances the space-charge force. Hence, the electrons are forced onto the beam axis and attract protons. Besides the energy dependent proton density increase on axis, the change in the particle spectrum is also important for future applications. Protons are accelerated/decelerated slightly, electrons highly. 2/3 of all electrons get lost directly at the source and 27% of all protons hit the inner wall of the solenoid.

42 ENGINEERING↗

Observations and Numerical Models of Solar Coronal Heating Associated with Spicules

Spicules have been proposed as significant contributors to the mass and energy balance of the corona. While previous observations have provided a glimpse of short-lived transient brightenings in the corona that are associated with spicules, these observations have been contested and are the subject of a vigorous debate both on the modeling and the observational side. Therefore, it remains unclear whether plasma is heated to coronal temperatures in association with spicules. We use high-resolution observations of the chromosphere and transition region (TR) with the Interface Region Imaging Spectrograph and of the corona with the Atmospheric Imaging Assembly on board the Solar Dynamics Observatory to show evidence of the formation of coronal structures associated with spicular mass ejections and heating of plasma to TR and coronal temperatures. Our observations suggest that a significant fraction of the highly dynamic loop fan environment associated with plage regions may be the result of the formation of such new coronal strands, a process that previously had been interpreted as the propagation of transient propagating coronal disturbances. Our observations are supported by 2.5D radiative MHD simulations that show heating to coronal temperatures in association with spicules. Our results suggest that heating and strong flows play an important role in maintaining the substructure of loop fans, in addition to the waves that permeate this low coronal environment.

79 ASTRONOMY AND ASTROPHYSICS↗

The magnetic flux in the quiet sun network

Direct magnetic measurements are used to confirm that the Ca II K line emission from the quiet sun network does not vary with the 11 year cycle (White and Livingston, 1981). As the K emission intensity is correlated with magnetic field strength, magnetic flux measurements are valid for comparison. Data were taken from the full-disk Mount Wilson daily magnetograms, and the aperture was decreased from 17.5 to 12.5 during the interval 1970 through 1980. Measurements are restricted to the latitude zones centered on + or - 1.7 degrees. The mean total flux in the + or - 15.3 degree zones increased by a factor of 10 between activity minimum and maximum, and the quiet sun flux shows no variation, thus confirming White and Livingston's (1981) result. In order for the amplitude of the quiet sun magnetic flux to remain constant, a balance between increasing and decreasing factors must exist, and the primary factor in this balance is the rate of destruction of the quiet sun flux.

Labonte, B. J.↗

Voyager Saturnian ring measurements and the early history of the solar system

The mass distribution in the Saturnian ring system is investigated and compared with predictions from plasma cosmogony. According to this theory, the matter in the rings was once a magnetized plasma, in which gravitation is balanced by the centrifugal and electromagnetic forces. As the plasma is neutralized, the electromagnetic forces disappear and the matter falls in to 2/3 of the original saturnocentric distance. This causes the cosmogonic shadow effect, demonstrated for the large scale structure of the Saturnian ring system. It is shown that many structures of the present ring system can be understood as shadows and antishadows of cosmogonic origin. These appear in the form of double rings centered around a position a factor 0.64 (slightly 2/3) closer to Saturn than the causing feature. Voyager data agree with an accuracy 1%.

Alfven, H.↗

Collisional processes in cometary plasmas

The interaction of the solar wind with comets is initiated at large distances from the nucleus by the ionization of cometary neutrals. The resulting contamination of the solar wind with cometary ions mass-loads the solar wind flow, causing it to slow down. The plasma-comet interaction is largely collisionless at large cometocentric distances. However, collisional processes become important in the inner coma (within the cometopause). Collisional processes include charge-transfer between solar wind protons and neutrals, ion-neutral friction, electron and ion thermal cooling, and ion-neutral chemistry. For example, the magnetometer on the Giotto spacecraft observed a diamagnetic cavity near closest approach. This cavity is a consequence of the balance between an inward-directed magnetic pressure gradient force and an outward ion-netural frictional force. Thermalization of the cometary ion distribution function by Coulomb collisions is another important process in the inner coma of an active comet.

Cravens, T. E.↗

Pressure changes in the plasma sheet during substorm injections

Data from the CHEM instrument on AMPTE CCE, data from the 3D plasma instrument and the SULEICA instrument on AMPTE IRM, and magnetometer data from both spacecraft are used to determine the particle pressure and total pressure as a function of radial distance in the plasma sheet for periods before and after the onset of substorm-associated ion enhancements over the range 7-19 RE. Events were chosen that occurred during times of increasing magnetospheric activity, as determined by an increasing AE index, in which a sudden increase, or 'injection', of energetic particle flux is observed. It is shown that the simultaneous appearance of energetic particles and changes in the magnetic field results naturally from pressure balance and does not necessarily indicate that the local changing field is accelerating the particles.

Kistler, L. M.↗

A 1050 K Stirling space engine design

As part of the NASA CSTI High Capacity Power Program on Conversion Systems for Nuclear Applications, Sunpower, Inc. completed for NASA Lewis a reference design of a single-cylinder free-piston Stirling engine that is optimized for the lifetimes and temperatures appropriate for space applications. The NASA effort is part of the overall SP-100 program which is a combined DOD/DOE/NASA project to develop nuclear power for space. Stirling engines have been identified as a growth option for SP-100 offering increased power output and lower system mass and radiator area. Superalloy materials are used in the 1050 K hot end of the engine; the engine temperature ratio is 2.0. The engine design features simplified heat exchangers with heat input by sodium heat pipes, hydrodynamic gas bearings, a permanent magnet linear alternator, and a dynamic balance system. The design shows an efficiency (including the alternator) of 29 percent and a specific mass of 5.7 kg/kW. This design also represents a significant step toward the 1300 K refractory Stirling engine which is another growth option of SP-100.

Penswick, L. Barry↗

Concept verification of three dimensional free motion simulator for space robot

In the development of automatic assembling technologies for space structures, it is an indispensable matter to investigate and simulate the movements of robot satellites concerned with mission operation. The movement investigation and simulation on the ground will be effectively realized by a free motion simulator. Various types of ground systems for simulating free motion have been proposed and utilized. Some of these methods are a neutral buoyancy system, an air or magnetic suspension system, a passive suspension balance system, and a free flying aircraft or drop tower system. In addition, systems can be simulated by computers using an analytical model. Each free motion simulation method has limitations and well known problems, specifically, disturbance by water viscosity, limited number of degrees-of-freedom, complex dynamics induced by the attachment of the simulation system, short experiment time, and the lack of high speed super-computer simulation systems, respectively. The basic idea presented here is to realize 3-dimensional free motion. This is achieved by combining a spherical air bearing, a cylindrical air bearing, and a flat air bearing. A conventional air bearing system has difficulty realizing free vertical motion suspension. The idea of free vertical suspension is that a cylindrical air bearing and counter balance weight realize vertical free motion. This paper presents a design concept, configuration, and basic performance characteristics of an innovative free motion simulator. A prototype simulator verifies the feasibility of 3-dimensional free motion simulation.

Okamoto, Osamu↗

Composition of the Moon as Determined from Orbit by Gamma-Ray Spectroscopy

A spacecraft placed in a planetary orbit of suitably high inclination will pass over all or most of the planet's surface in a matter of several weeks to months. The quite prodigious scientific potential of planetary orbiters lies in coupling this comprehensive coverage with observing systems capable of gathering data on properties that include elemental and mineralogic composition, exogenic and endogenic surface alterations, thermal balance, gravity, topography, stratigraphy, albedo and magnetism.

gramma-ray spectroscopy↗

Characterization of admissible quasisymmetries

We solve ‘half’ the problem of finding three-dimensional quasisymmetric magnetic fields that do not necessarily satisfy magnetohydrostatic force balance. This involves determining which hidden symmetries are admissible as quasisymmetries, and then showing explicitly how to construct quasisymmetric magnetic fields given an admissible symmetry. The admissibility conditions take the form of a system of overdetermined nonlinear partial differential equations involving second derivatives of the symmetry's infinitesimal generator.

Burby, J. W. (ORCID:0000000317727647)↗

Exchange coupling torque in ferrimagnetic Co/Gd bilayer maximized near angular momentum compensation temperature

Highly efficient current-induced motion of chiral domain walls was recently demonstrated in synthetic antiferromagnetic (SAF) structures due to an exchange coupling torque (ECT). The ECT derives from the antiferromagnetic exchange coupling through a ruthenium spacer layer between the two perpendicularly magnetized layers that comprise the SAF. Here we report that the same ECT mechanism applies to ferrimagnetic bi-layers formed from adjacent Co and Gd layers. In particular, we show that the ECT is maximized at the temperature T A where the Co and Gd angular momenta balance each other, rather than at their magnetization compensation temperature T M . The current induced velocity of the domain walls is highly sensitive to longitudinal magnetic fields but we show that this not the case near T A . Our studies provide new insight into the ECT mechanism for ferrimagnetic systems. The high efficiency of the ECT makes it important for advanced domain wall based spintronic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure and Variability of the Martian Ion Composition Boundary Layer

A complex boundary layer with a variety of charged particle and electromagnetic field signatures, including a transition between plasma predominantly of solar wind origin and plasma of planetary origin, lies between the Martian bow shock and the ionosphere. In this paper, we develop and utilize algorithms to autonomously identify and characterize this ion composition boundary (ICB), using data from the Mars Atmosphere and Volatile EvolutioN (MAVEN) mission. We find an asymmetric ICB with a larger average thickness, lower altitude, and lower velocity shear in the hemisphere where the solar wind motional electric field points outward, as a result of the asymmetry of the mass loading process. The ICB thickness scales with the magnetosheath proton gyroradius at the top of the boundary layer but does not clearly vary with external drivers. The ICB location varies with solar wind ram pressure and crustal magnetic field strength, but does not clearly respond to solar wind Mach number or extreme ultraviolet irradiance. The ICB represents a distinct boundary for ion density and flow speed, but the magnetic field strength and direction typically do not vary significantly across the ICB. The plasma density and flow speed at the ICB vary seasonally, likely in response to variations in the neutral exosphere and/or atmosphere. However, the ICB on average remains at or below the altitude where pressure balance is achieved between the piled up magnetic field (MPB) and the solar wind ram pressure, regardless of season or crustal magnetic field strength.

Electromagnetic↗

Development of a capacitance measurement for pulsed magnetic fields

Capacitance measurements are crucial for probing the electrical properties of materials. In this study, we develop and implement a capacitance measurement technique optimized for pulsed magnetic fields. Our approach employs an auto-balancing bridge method, leveraging a high-bandwidth transimpedance amplifier to mitigate parasitic contributions from coaxial cables. This technique enables precise capacitance measurements in rapidly changing magnetic fields, as demonstrated in experiments on the magnetoelectric material NiCo 2 TeO 6 . The results reveal strong magnetoelectric coupling, including a pronounced hysteresis in capacitance that coincides with magnetization measurements and an enhanced energy dissipation peak at high sweep rates. Compared to traditional LCR meter measurements in DC fields, our method exhibits excellent agreement while providing additional insight into field-induced phase transitions. This work establishes a robust methodology for capacitance measurements under extreme conditions and opens new opportunities for studying multiferroic and correlated electron systems under high magnetic fields.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗