Results for “National Transonic Facility” — Page 25

NASA NTRS2019

Additional Findings from the Common Research Model Natural Laminar Flow Wind Tunnel Test

An experimental investigation of the Common Research Model with Natural Laminar Flow (CRM-NLF) took place in the National Transonic Facility (NTF) at the NASA Langley Research Center in 2018. The 5.2% scale semispan model was designed using a new natural laminar flow design method, Crossflow Attenuated NLF (CATNLF). CATNLF enables laminar flow on typical transport wings with high sweep and Reynolds number by reshaping the wing airfoils to obtain specific pressure distribution characteristics that control the crossflow growth near the leading edge. The CATNLF method also addresses Tollmien- Schlichting transition, attachment line transition, and Görtler vortices. During the wind tunnel test, data were acquired to address three primary test objectives: validate the CATNLF design method, characterize the NTF laminar flow testing capabilities, and establish best practices for laminar flow wind tunnel testing. The present paper provides both experimental and computational data to understand the CRM-NLF laminar flow characteristics, as well as address the three primary test objectives. The effects of angle of attack and Reynolds number on the CRM-NLF laminar flow extent are studied, and the dominant transition mechanism is evaluated at a variety of test conditions. Critical N-factors are calculated for the NTF environment, and a discussion on best practices for laminar flow wind tunnel testing is provided. The CRM-NLF in the NTF provided initial confirmation of the ability of the CATNLF method to suppress crossflow growth and enable significant extents of laminar flow on transport wings with high sweep and Reynolds numbers.

Lynde, Michelle N.↗

NASA NTRS2019

Transition Detection at Cryogenic Temperatures Using a Carbon-Based Resistive Heating Layer Coupled with Temperature Sensitive Paint

This paper will highlight the development and application of a carbon-based resistive heating layer for use in transition detection at cryogenic temperatures at the National Transonic Facility (NTF) for full-flight Reynolds number testing. This study builds upon previous work that was successfully demonstrated at the 0.3-m Transonic Cryogenic Tunnel on a smaller-scale airfoil shape of regular geometry. However, the test performed at the NTF involved a semispan wing with complex geometry and significantly larger than previous tests. This required the development of new coatings to provide suitable resistances to provide adequate heating rates for transition detection. Successful implementation of this technology has the ability to greatly enhance transition detection experiments at cryogenic temperatures as well as reducing perturbation in the tunnel caused by more traditional transition detection methods.

Watkins, A. Neal↗

NASA NTRS2020

FLEET Velocimetry in the Common Research Model’s Wing Wake

Femtosecond laser electronic excitation tagging was used to make velocity measurements in the wake of the wing of the Common Research Model (CRM). Experiments were performed in the NASA Langley Research Center’s National Transonic Facility over a range of tunnel operating conditions. Pressures ranged from 205 to 411 kPa, temperatures from 278 to 323 K, and Mach from 0.1 to 0.9. Velocity was also determined over a range of model angles of attack. Time-averaged velocity results were obtained in both air and nitrogen, while single-shot velocity was obtained under certain tunnel operating conditions. Spatially-resolved, two dimensional, single component velocity measurements were achieved using a newly-developed laser scanning technique, which proved sufficiently sensitive to measure an approximately 5% velocity deficit in the wing wake region of the CRM.

Daniel T Reese↗

NASA NTRSDate not supplied

NTF Test 201 - FAVOR - F-111 Check Standard

Presentation of test process at the National Transonic Facility, Nasa Langley Research Center. The test showcased was part of a cooperative test effort between ARC, LaRC, GRC, and AEDC collecting aerodynamic and process data on the modified F-111 FAVOR model.

Michael D Treece↗

NASA NTRSDate not supplied

Virtual Diagnostics Interface (ViDI) for Planning Laser-Based Wind Tunnel Experiments

Virtual Diagnostics Interface (ViDI), originally introduced by Richard Schwartz in 2004 and described again by Alderfer, et. al., in 2007, is an interactive 3D software tool developed at NASA Langley Research Center to serve three main purposes: assist in pre-test planning, enhance post-test image analysis and visualization, and serve as a central location for data storage and distribution.1,2 ViDI is composed of custom-developed software and Autodesk® 3ds Max® as it incorporates Computer Aided Design (CAD) models with the results obtained from optical diagnostics.3 This software tool has proven useful in the field of optical diagnostics where pre-test planning of beam paths, optical elements, and test articles must be carried out to avoid interference, ensure spatial resolution is sufficient, and the camera Field of View (FoV) is adequate for the field of interest. Typically, practical considerations such as the distance a camera is from the region of interest, the angles at which the camera is oriented and issues such as the size of the camera and its sensor and size and focal length lens as well as the path of the laser need to be taken into account to predict a successful measurement. An example application of ViDI is shown in Fig.1 where an experiment to investigate flow separation over the wing of the High Lift Common Research Model (HL-CRM) is currently being planned in the National Transonic Facility (NTF) at NASA Langley Research Center.

virtual diagnostics interface↗

NASA NTRS2021

Assessment of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon transition correlations that were derived from a limited number of low-speed experiments and these models often fail to account for all of the relevant transition mechanisms and/or the variation in those mechanisms with respect to changes in the significant flow parameters. Available data from a recent experiment on the Common Research Model with Natural Laminar Flow (CRM-NLF) in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.3b solver for a swept wing configuration with nonzero taper and transonic cruise conditions. Specifically, the OVERFLOW solutions are used to evaluate the accuracy and robustness of the transport-equation-based transition models. Results highlight that the Spalart-Allmaras-based amplification factor transport (AFT-2017b) equation model and Menter’s shear-stress transport equation (SST2003)-based Langtry-Menter transition models (either with or without the modeling of crossflow transition) significantly underpredict the reported extent of laminar flow region over the entire span of the wing, irrespective of which instability mechanism(s) is expected to dominate the onset of the transition process. We show that the transition correlations underlying these models fail to account for the stabilizing effect of compressibility on the Tollmien-Schlichting transition, which is likely to be a major contributor to the underprediction of the laminar flow region on the CRM-NLF. The SST-2003-based Langtry-Menter model also appears to inaccurately predict the chordwise pressure variation along the majority of the wing span at all the flow conditions studied herein, due to how the turbulence intensity levels were enforced in the computations and how that was interfering with the functioning of the underlying turbulence model within the boundary layer. The AFT and Langtry-Menter models appear to be sensitive to the level of the freestream turbulence intensity, but the degree of sensitivity varies across the models.

CFD modeling↗

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗

NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗

NASA NTRS2023

Improvement of Pressure Sensitive Paint in A Cryogenic Oxygen-Poor Environment

This report details specific improvements to the use of Pressure Sensitive Paint (PSP) in an oxygen-poor environment, with an emphasis on cryogenic PSP in the National Transonic Facility (NTF). For this work, several improvements to the application of PSP and data acquisition have been investigated in the 0.3-m Transonic Cryogenic Tunnel (generally considered a pilot facility for the NTF) and these results will be presented. In addition, several improvements to the existing PSP system at NTF are presented as well as a brief section on further improvements that can be investigated.

Cryogenic ground testing↗

NASA NTRSDate not supplied

Transition Modeling Based on the Dual N-factor Method for the CRM-NLF Wind Tunnel Configuration

The dual N-factor method is used to model the boundary-layer transition over the common research model with natural laminar flow (CRM-NLF) aircraft configuration. The flow conditions match selected test conditions from a wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. The paper presents a systematic methodology for transition prediction in the presence of a dual shock system and extends the prior capability for iteratively coupled computational fluid dynamics (CFD) predictions to incorporate three-dimensional, transonic wings. The method employs stability computations based on the linear parabolized stability equations (PSE), along with a dual N-factor criterion. The iterative process begins with the fully turbulent Reynolds-averaged-Navier-Stokes (RANS) mean flow solution. For the first iteration, a mean flow solution is calculated with an imposed transition front that aligns with the shock front from the fully turbulent solution. Subsequently, stability computations are performed along a set of streamlines across the wing to calculate the amplification of planar Tollmien-Schlichting (TS) and stationary crossflow (CF) modes. The transition criterion based on the dual N-factor method is used to infer the updated transition front and the process is successively repeated until convergence of the solution. Within three iterations, the predicted fronts for angles of attack of 1.45, 1.98, 2.46 and 2.94 degrees and a mean-aerodynamic-chord Reynolds number equal to 15 million, approach visual convergence in most regions of the studied cases, and the resulting predictions are in good agreement with the transition fronts deduced from measurements of temperature-sensitive paint. Even though surface pressure measurements based on fully-turbulent flow agree well with the measured pressure coefficient distributions, strong viscous-inviscid interaction effects cause significant shifts in the shock locations based on the imposed transition front, underscoring the intrusive nature of static pressure measurements using surface mounted ports on the CRM-NLF configuration.

Boundary Layer Transition↗

NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗

NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗

NASA NTRSDate not supplied

NASA Contributions to the High Lift Common Research Model Ecosystem

As part of the High Lift Common Research Model (CRM-HL) ecosystem, NASA has designed and built two CRM-HL models. The first model is a 5.2% scale semispan model that has been tested in the NASA Langley 14- by 22-Foot Subsonic Wind Tunnel (14x22), the low-speed wind tunnel DNW-NWB in Germany and in the National Transonic Facility (NTF) at NASA Langley Research Center. Information on the NASA tests that will include model details, test methods and some test data will be presented in the final document. The second model is a 2.7% scale model that will also be tested in the NTF in both full span and semispan configurations. Information on the design and fabrication of this model will be included in the final document.

Melissa Rivers↗

NASA NTRSDate not supplied

Computational Analysis of a Boundary Layer Ingesting Tailcone Thruster Configuration Using the LAVA Curvilinear Solver

Boundary layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA's Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) wind tunnel to study the propulsion-airframe integration effects of the Boundary Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) curvilinear solver to validate the applicability of current best-practice Reynolds-Averaged Navier-Stokes (RANS) models in accurately predicting the relevant flow physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles of attack between -3 and 4 degrees. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions is analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aft body boundary layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA curvilinear solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage. This talk will cover the combined experimental and numerical efforts that resulted from this BLI-focused investigation.

ARMD↗

NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗

NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗

NASA NTRS2010

Statistical Analysis of CFD Solutions from the Fourth AIAA Drag Prediction Workshop

A graphical framework is used for statistical analysis of the results from an extensive N-version test of a collection of Reynolds-averaged Navier-Stokes computational fluid dynamics codes. The solutions were obtained by code developers and users from the U.S., Europe, Asia, and Russia using a variety of grid systems and turbulence models for the June 2009 4th Drag Prediction Workshop sponsored by the AIAA Applied Aerodynamics Technical Committee. The aerodynamic configuration for this workshop was a new subsonic transport model, the Common Research Model, designed using a modern approach for the wing and included a horizontal tail. The fourth workshop focused on the prediction of both absolute and incremental drag levels for wing-body and wing-body-horizontal tail configurations. This work continues the statistical analysis begun in the earlier workshops and compares the results from the grid convergence study of the most recent workshop with earlier workshops using the statistical framework.

Statistical analysis↗

NASA NTRS1985

Response time correlations for platinum resistance thermometers in flowing fluids

The thermal response of two types of Platinum Resistance Thermometers (PRT's), which are being considered for use in the National Transonic Wind Tunnel Facility, were studied. Response time correlations for each PRT, in flowing water, oil and air, were established separately. A universal correlation, tau WOA = 2.0 + 1264, 9/h, for a Hy-Cal Sensor (with a reference resistance of 100 ohm) within an error of 20% was established while the universal correlation for the Rosemount Sensor (with a reference resistance of 1000 ohm), tau OA = 0.122 + 1105.6/h, was found with a maximum percentage error of 30%. The correlation for the Rosemount Sensor was based on air and oil data only which is certainly not sufficient to make a correlation applicable to every condition. Therefore, the correlation needs more data to be gathered in different fluids. Also, it is necessary to state that the calculation of the parameter, h, was based on the available heat transfer correlations, whose accuracies are already reported in literature uncertain within 20-30%. Therefore, the universal response constant correlations established here for the Hy-Cal and Rosemount sensors are consistent with the uncertainty in the input data and are recommended for future use in flowing liquids and gases.

Pandey, D. K.↗