Search NASA⌕ Search

SEARCH · Search NASA

Results for “ORTHOGONAL FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Effects of volume averaging on the line spectra of vertical velocity from multiple-Doppler radar observations

Calculations of the ratio of the true one-dimensional spectrum of vertical velocity and that measured with multiple-Doppler radar beams are presented. It was assumed that the effects of pulse volume averaging and objective analysis routines is replacement of a point measurement with a volume integral. A u and v estimate was assumed to be feasible when orthogonal radars are not available. Also, the target fluid was configured as having an infinite vertical dimension, zero vertical velocity at the top and bottom, and having homogeneous and isotropic turbulence with a Kolmogorov energy spectrum. The ratio obtained indicated that equal resolutions among radars yields a monotonically decreasing, wavenumber-dependent response function. A gain of 0.95 was demonstrated in an experimental situation with 40 levels. Possible errors introduced when using unequal resolution radars were discussed. Finally, it was found that, for some flows, the extent of attenuation depends on the number of vertical levels resolvable by the radars.

Gal-Chen, T.↗
NASA NTRS1990

Implicit application of polynomial filters in a k-step Arnoldi method

The Arnoldi process is a well known technique for approximating a few eigenvalues and corresponding eigenvectors of a general square matrix. Numerical difficulties such as loss of orthogonality and assessment of the numerical quality of the approximations as well as a potential for unbounded growth in storage have limited the applicability of the method. These issues are addressed by fixing the number of steps in the Arnoldi process at a prescribed value k and then treating the residual vector as a function of the initial Arnoldi vector. This starting vector is then updated through an iterative scheme that is designed to force convergence of the residual to zero. The iterative scheme is shown to be a truncation of the standard implicitly shifted QR-iteration for dense problems and it avoids the need to explicitly restart the Arnoldi sequence. The main emphasis of this paper is on the derivation and analysis of this scheme. However, there are obvious ways to exploit parallelism through the matrix-vector operations that comprise the majority of the work in the algorithm. Preliminary computational results are given for a few problems on some parallel and vector computers.

Sorensen, D. C.↗
NASA NTRS1971

Attitude stability of spinning flexible spacecraft

The stability of spinning flexible satellites in a force-free environment was analyzed. The satellite was modeled as a rigid core having attached to it a flexible appendage idealized as a collection of particles (point masses) interconnected by springs. Both Liapunov and Routh-Hurwitz stability procedures are used. In the former, the Hamiltonian of the system, constrained through the angular momentum integral so as to admit complete damping, is used as a testing function. Equations of motion are written using the hybrid coordinate formulation, which readily accepts a modal coordinate transformation ultimately allowing truncation to a level amenable to literal stability analysis. Closed form stability criteria are generated for the first mode of a restricted appendage model lying in a plane containing the system center of mass and orthogonal to the spin axis. The effects of spin on flexible bodies are discussed by considering a very elementary particle model. Control of passively unstable spacecraft is briefly considered.

Likins, P. W.↗
NASA NTRS2014

Habitat Demonstration Unit (HDU) Vertical Cylinder Habitat

NASA's Constellation Architecture Team defined an outpost scenario optimized for intensive mobility that uses small, highly mobile pressurized rovers supported by portable habitat modules that can be carried between locations of interest on the lunar surface. A compact vertical cylinder characterizes the habitat concept, where the large diameter maximizes usable flat floor area optimized for a gravity environment and allows for efficient internal layout. The module was sized to fit into payload fairings for the Constellation Ares V launch vehicle, and optimized for surface transport carried by the All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) mobility system. Launch and other loads are carried through the barrel to a top and bottom truss that interfaces with a structural support unit (SSU). The SSU contains self-leveling feet and docking interfaces for Tri-ATHLETE grasping and heavy lift. A pressurized module needed to be created that was appropriate for the lunar environment, could be easily relocated to new locations, and could be docked together in multiples for expanding pressurized volume in a lunar outpost. It was determined that horizontally oriented pressure vessels did not optimize floor area, which takes advantage of the gravity vector for full use. Hybrid hard-inflatable habitats added an unproven degree of complexity that may eventually be worked out. Other versions of vertically oriented pressure vessels were either too big, bulky, or did not optimize floor area. The purpose of the HDU vertical habitat module is to provide pressurized units that can be docked together in a modular way for lunar outpost pressurized volume expansion, and allow for other vehicles, rovers, and modules to be attached to the outpost to allow for IVA (intra-vehicular activity) transfer between them. The module is a vertically oriented cylinder with a large radius to allow for maximal floor area and use of volume. The modular, 5- m-diameter HDU vertical habitat module consists of a 2-m-high barrel with 0.6-mhigh end domes forming the 56-cubicmeter pressure vessel, and a 19-squaremeter floor area. The module has up to four docking ports located orthogonally from each other around the perimeter, and up to one docking port each on the top or bottom end domes. In addition, the module has mounting trusses top and bottom for equipment, and to allow docking with the ATHLETE mobility system. Novel or unique features of the HDU vertical habitat module include the nodelike function with multiple pressure hatches for docking with other versions of itself and other modules and vehicles; the capacity to be carried by an ATHLETE mobility system; and the ability to attach inflatable 'attic' domes to the top for additional pressurized volume.

Howe, Alan↗
NASA NTRS1992

Determining water cloud particle sizes from lidar depolarization measurements and time dependent multiple scattering coefficients

We present a technique of extracting water cloud particle size information from lidar measurements in conjunction with double scattering calculations. In this presentation, we describe the technique and give examples using data taken with the Air Force Phillips Laboratory's (Geophysics Directorate) low altitude Nd:YAG, elastic backscatter lidar. In a related presentation we describe the double scattering lidar model which we developed for this work. The technique uses simultaneous measurements of two orthogonal linear polarization components of lidar returns from water clouds or other media composed of spherical particles. Any depolarization of the incident lidar radiation backscattered by such a media can only be due to multiple scattering. The amount of depolarization is dependent on the extinction coefficient and the single scatter phase matrix, both of which are functions of position in the medium. The phase matrix is dependent on the index of refraction of the particles and the particle size distribution. Our technique is a modification of a procedure presented in Reference 1. There, particle sizes of water clouds are determined from double scattering calculations together with measurements of radiation scattered from volumes outside the lidar receiver's field of view (which can only be multiply scattered radiation). The methodology of our technique is similar but our 'probe' of the scattering phase function (and thus the particle size distribution) is different.

Garner, R. C.↗
DOE OSTI2025

A Colebrook equation for impinging radial wall jets

Here, in this study, we evaluate the skin coefficient of friction for steady turbulent radial wall jets across smooth and rough surfaces. Although the Colebrook equation has been used successfully for many decades to evaluate friction factors for flows through smooth and rough pipes, how roughness affects the skin friction coefficient for steady turbulent radial wall jets remains unclear. Here we explore a Colebrook-type equation for skin friction coefficients associated with single-phase turbulent radial wall jets arising from orthogonally impinging circular jets. The fully iterative solution, based on well-established concepts of turbulent wall-bounded flow, is presented along with a power-law approximation and a non-iterative approximation for the friction coefficient derived therefrom. We find the skin coefficient of friction defined on the peak radial velocity to be a function of position over rough but not smooth surfaces in contrast to pipe friction factors that remain independent of axial position. These results follow expected trends, explain prior heterogeneity in power-law expressions for the skin friction coefficient and have significant implications for the industrial use of jets in mixing vessels.

friction losses↗
NASA NTRS1999

Multi-Axis Thrust Measurements of the EO-1 Pulsed Plasma Thruster

Pulsed plasma thrusters are low thrust propulsive devices which have a high specific impulse at low power. A pulsed plasma thruster is currently scheduled to fly as an experiment on NASA's Earth Observing-1 satellite mission. The pulsed plasma thruster will be used to replace one of the reaction wheels. As part of the qualification testing of the thruster it is necessary to determine the nominal thrust as a function of charge energy. These data will be used to determine control algorithms. Testing was first completed on a breadboard pulsed plasma thruster to determine nominal or primary axis thrust and associated propellant mass consumption as a function of energy and then later to determine if any significant off-axis thrust component existed. On conclusion that there was a significant off-axis thrust component with the bread-board in the direction of the anode electrode, the test matrix was expanded on the flight hardware to include thrust measurements along all three orthogonal axes. Similar off-axis components were found with the flight unit.

Arrington, Lynn A.↗
NASA NTRS2009

Shape Distribution of Fragments from Microsatellite Impact Tests

Fragment shape is an important factor for conducting reliable orbital debris damage assessments for critical space assets, such as the International Space Station. To date, seven microsatellite impact tests have been completed as part of an ongoing collaboration between Kyushu University and the NASA Orbital Debris Program Office. The target satellites ranged in size from 15 cm 15 cm 15 cm to 20 cm 20 cm 20 cm. Each target satellite was equipped with fully functional electronics, including circuits, battery, and transmitter. Solar panels and multi-layer insulation (MLI) were added to the target satellites of the last two tests. The impact tests were carried out with projectiles of different sizes and impact speeds. All fragments down to about 2 mm in size were collected and analyzed based on their three orthogonal dimensions, x, y, and z, where x is the longest dimension, y is the longest dimension in the plane perpendicular to x, and z is the longest dimension perpendicular to both x and y. Each fragment was also photographed and classified by shape and material composition. This data set serves as the basis of our effort to develop a fragment shape distribution. Two distinct groups can be observed in the x/y versus y/z distribution of the fragments. Objects in the first group typically have large x/y values. Many of them are needle-like objects originating from the fragmentation of carbon fiber reinforced plastic materials used to construct the satellites. Objects in the second group tend to have small x/y values, and many of them are box-like or plate-like objects, depending on their y/z values. Each group forms the corresponding peak in the x/y distribution. However, only one peak can be observed in the y/z distribution. These distributions and how they vary with size, material type, and impact parameters will be described in detail within the paper.

Liou, J.C.↗
NASA NTRS1975

Attitude determination of a high altitude balloon system. Part 2: Development of the parameter determination process

The attitude of the balloon system is determined as a function of time if: (a) a method for simulating the motion of the system is available, and (b) the initial state is known. The initial state is obtained by fitting the system motion (as measured by sensors) to the corresponding output predicted by the mathematical model. In the case of the LACATE experiment the sensors consisted of three orthogonally oriented rate gyros and a magnetometer all mounted on the research platform. The initial state was obtained by fitting the angular velocity components measured with the gyros to the corresponding values obtained from the solution of the math model. A block diagram illustrating the attitude determination process employed for the LACATE experiment is shown. The process consists of three essential parts; a process for simulating the balloon system, an instrumentation system for measuring the output, and a parameter estimation process for systematically and efficiently solving the initial state. Results are presented and discussed.

Nigro, N. J.↗
NASA NTRS1993

A European mobile satellite system concept exploiting CDMA and OBP

This paper describes a novel Land Mobile Satellite System (LMSS) concept applicable to networks allowing access to a large number of gateway stations ('Hubs'), utilizing low-cost Very Small Aperture Terminals (VSAT's). Efficient operation of the Forward-Link (FL) repeater can be achieved by adopting a synchronous Code Division Multiple Access (CDMA) technique, whereby inter-code interference (self-noise) is virtually eliminated by synchronizing orthogonal codes. However, with a transparent FL repeater, the requirements imposed by the highly decentralized ground segment can lead to significant efficiency losses. The adoption of a FL On-Board Processing (OBP) repeater is proposed as a means of largely recovering this efficiency impairment. The paper describes the network architecture, the system design and performance, the OBP functions and impact on implementation. The proposed concept, applicable to a future generation of the European LMSS, was developed in the context of a European Space Agency (ESA) study contract.

Vernucci, A.↗
NASA NTRS1981

The formation of arcs in the dynamic spectra of Jovian decameter bursts

A model is presented that accounts for several features of the dynamic spectral arcs observed at decameter wavelengths by the planetary radio astronomy experiment on Voyagers 1 and 2. It is shown that refraction of an extraordinary mode wave initially excited and nearly orthogonal to the local magnetic field is significantly influenced by the local plasma density. The source of the radiation is on the L = 6 flux, and the emission cone angle of the sheet is chosen to vary with frequency so that it is relatively small at both high and low frequencies while about 80 deg at intermediate frequencies. This functional dependence of cone angle on frequency appears to be consistent with estimates of refraction of the ordinary mode in a source region where the electron density is greater than a few hundred per cu cm.

Goldstein, M. L.↗
NASA NTRS1991

Proper orthogonal decomposition based turbulence modeling

The proper orthogonal decomposition is utilized to provide one mode estimates of various turbulence quantities in the near-wall region of the turbulent boundary layer. The experimental data of Herzog (1986) and the direct numerical simulation (DNS) results of Zang (1991) proved the two-point correlation tensor. The correlation tensor is then used as the kernel in the integral eigenvalue problem from which the proper orthogonal modes are obtained. The one mode estimates of the turbulent kinetic energy, dissipation, and triple moments all exhibit the proper asymtotic behavior near the wall. As a validation test, a model for the triple moments is developed and its near-wall behavior is studied. This information can then be used to obtain an estimate of the damping function near the wall, which is then compared to known existing behavior. Since this is an initial investigation, the streamwise and spanwise dependence is surpressed and only the wall normal direction (y+) behavior of various turbulence statistics near the wall is studied. Before examining one mode estimates of the triple moments and the dissipation (on which the model is based), various second order moments are examined. If these do not exhibit the proper behavior near the wall (as discussed by Speziale et al 1990) it does not seem reasonable to expect the one mode estimate of the triple moment and dissipation to have the right behavior. Only the results obtained using the experimental data of Herzog are discussed since the results from the simulations of Zang exhibit similar behavior as discussed above.

Glauser, Mark N.↗
NASA NTRS2019

GOES-17 Magnetometer On-Orbit Calibration Design and Results

The Geostationary Operational Environmental Satellite-R (GOES-R) is a series of four NOAA weather satellites. Each spacecraft flies a Magnetometer instrument which includes two boom mounted fluxgate sensors located 6.3 and 8.5 meters from the spacecraft. Sensor readings are corrupted by both internal (bias and scale factor) and external (spacecraft emitted fields and misalignments) error sources. In order to estimate the bias, an on-orbit calibration is performed, slewing the spacecraft about multiple axes and then performing a fit of the data to determine zero offset and misalignment terms. The first satellite in the series, GOES-16 was launched in November 2016. Its magnetometer calibration maneuver was found to be inadequate providing insufficient rotation about orthogonal axes. The uncertainty in the estimated biases was found to be in the 3-5 nanotesla range, exceeding the magnetometer accuracy requirement of 1.0 nanotesla. Based on lessons learned, the maneuver was redesigned to provide multiple 360 degree rotations about two orthogonal axes, providing optimal visibility into bias and misalignment. Varying ambient fields over the duration of the calibration maneuvers, corrupts the ability to accurately determine parameters of interest. To address this issue, rather than assuming a constant field for the duration of the maneuver, a non-linear least squares filter was employed that uses a series of spline functions to better fit the ambient field. The number of splines can be varied to minimize the least squares filter residuals. Simulations were performed using 360 days of GOES-16 data to bound the uncertainty in the biases for given residuals of the fit to the ambient field. Following the launch of the second satellite in the series, GOES-17 in March 2018, the new calibration maneuver and enhanced bias estimation algorithm were exercised twice. Based on the residuals of the fit, the uncertainty of the estimated zero offset was reduced by an order of magnitude from 3-5 nanotesla to approximately 0.4 nanotesla per axis. This paper provides details of the maneuver design and the innovative algorithm used to estimate the GOES-17 biases and misalignments.

GOES-17↗
NASA NTRSDate not supplied

Lidar Simulations of Backscatter and Extinction Uncertainty Estimates for ACCP Assessments

As part of the NASA Aerosols and Clouds, Convection, and Precipitation (ACCP) pre-formulation study, several lidar instruments are being assessed for their capabilities in advancing the science objectives enumerated in the most recent Earth Sciences Decadal Survey. These assessments are conducted using the NASA Langley Research Center(LaRC) lidar simulator, which produces profiles of backscatter and extinction uncertainty estimates for a given set of input parameters. Specifically, attention is focused onevaluating the science benefits and improvements of a candidate two-wavelength space-based High Spectral Resolution Lidar (HSRL) compared to an elastic backscatter lidar with similar capabilities to the Cloud-Aerosol Lidar with Orthogonal Polarization(CALIOP), flying aboard the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite. In this talk, simulations of satellite-based HSRL and those of a CALIOP-like system are compared for different atmospheric scenes that capture varying total aerosol loadings, aerosol vertical distributions, and aerosol types.The results of these analyses are presented as functions of averaging resolution(horizontal/vertical), lighting conditions (daytime/nighttime), surface type (land/ocean),and wavelength (532 nm/1064 nm). Also, simulations of multiple aerosol layers and of aerosols beneath transparent cirrus clouds are shown to demonstrate the consequent impacts on underlying backscatter and extinction uncertainties, and to better differentiate the performance of HSRL compared to that of CALIOP for real-world atmospheric scenarios.

Travis D. Toth↗
NASA NTRS1989

Numerical optimization in Hilbert space using inexact function and gradient evaluations

Trust region algorithms provide a robust iterative technique for solving non-convex unstrained optimization problems, but in many instances it is prohibitively expensive to compute high accuracy function and gradient values for the method. Of particular interest are inverse and parameter estimation problems, since function and gradient evaluations involve numerically solving large systems of differential equations. A global convergence theory is presented for trust region algorithms in which neither function nor gradient values are known exactly. The theory is formulated in a Hilbert space setting so that it can be applied to variational problems as well as the finite dimensional problems normally seen in trust region literature. The conditions concerning allowable error are remarkably relaxed: relative errors in the gradient error condition is automatically satisfied if the error is orthogonal to the gradient approximation. A technique for estimating gradient error and improving the approximation is also presented.

Carter, Richard G.↗
DOE OSTI2024

Force-Free Identification of Minimum-Energy Pathways and Transition States for Stochastic Electronic Structure Theories

Here, the accurate mapping of potential energy surfaces (PESs) is crucial to our understanding of the numerous physical and chemical processes mediated by atomic rearrangements, such as conformational changes and chemical reactions, and the thermodynamic and kinetic feasibility of these processes. Stochastic electronic structure theories, e.g., Quantum Monte Carlo (QMC) methods, enable highly accurate total energy calculations that in principle can be used to construct the PES. However, their stochastic nature poses a challenge to the computation and use of forces and Hessians, which are typically required in algorithms for minimum-energy pathway (MEP) and transition state (TS) identification, such as the nudged elastic band (NEB) algorithm and its climbing image formulation. Here, we present strategies that utilize the surrogate Hessian line-search method, previously developed for QMC structural optimization, to efficiently identify MEP and TS structures without requiring force calculations at the level of the stochastic electronic structure theory. By modifying the surrogate Hessian algorithm to operate in path-orthogonal subspaces and at saddle points, we show that it is possible to identify MEPs and TSs by using a force-free QMC approach. We demonstrate these strategies via two examples, the inversion of the ammonia (NH 3 ) molecule and the nucleophilic substitution (S N 2) reaction F – + CH 3 F → FCH 3 + F – . We validate our results using Density Functional Theory (DFT)- and Coupled Cluster (CCSD, CCSD(T))-based NEB calculations. We then introduce a hybrid DFT-QMC approach to compute thermodynamic and kinetic quantities, free energy differences, rate constants, and equilibrium constants that incorporates stochastically optimized structures and their energies, and show that this scheme improves upon DFT accuracy. Our methods generalize straightforwardly to other systems and other high-accuracy theories that similarly face challenges computing energy gradients, paving the way for highly accurate PES mapping, transition state determination, and thermodynamic and kinetic calculations at significantly reduced computational expense.

Iyer, Gopal R.↗
NASA NTRS1975

Study of the performance of antennas in magnetized plasmas

The antenna studies were performed in a large magnetized plasma source, a schematic drawing of which is shown. The plasma diagnostics consist of a 70 GHz (4 mm) microwave interferometer for density measurements and of various Langmuir probes for spatially resolved measurements of t sub e, n sub e and the shape of the electron distribution function. All diagnostic data are time-resolved by sample-and-hold techniques so as to yield information about the plasma build-up, the steady-state discharge, and the plasma decay in the afterglow. Whistler waves are excited and detected with various antennas which are inserted into the center of the plasma column through one axial and two orthogonal radial ports. The antennas were tested for their proper dipole response and then calibrated in a known field geometry in air. For the electric dipole, a parallel plate capacitor field was used; the magnetic loop is calibrated in the near-zone field of a long linear conductor of known radio frequency current distribution. Results are presented and discussed.

Stenzel, R. L.↗
NASA NTRS1989

An algebraic model for the turbulent flux of a passive scalar

Direct numerical simulations of the unsteady incompressible Navier-Stokes equations have been performed in order to investigate the behavior of passive-scalar fields resulting from mean scalar gradients in each of three orthogonal directions in homogeneous turbulent shear flow. For all orientations of the mean scalar gradient, the sum of the pressure-scalar gradient and velocity gradient-scalar gradient terms in the turbulent scalar flux balance equation are found to be approximately aligned with the scalar flux vector itself. The simulation results are used to obtain dimensionless model coefficients as a function of the turbulence Reynolds and Peclet numbers.

Rogers, Michael M.↗