Search NASA⌕ Search

SEARCH · Search NASA

Results for “Operating Mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Face-seal lubrication. 2: Theory of response to angular misalignement

A theoretical analysis was made of a hypothetical seal operating mode. The hypothetical seal model provides for three degrees of primary ring motion and includes the force and moments induced by primary ring response to seat angular misalignment. This ring response causes a relative angular misalignment between the faces of the primary seal. Hydrodynamic pressure generation is produced by this misalignment. The analysis is based on the Reynolds equation in short bearing form and on a balance of forces and moments that arise from hydrodynamic and secondary seal friction effects. A closed form solution was obtained that can be solved for film thickness and relative angular misalignment.

Ludwig, L. P.↗
NASA NTRS1976

Design and analysis of a cryogenic variable conductance axial grooved heat pipe

An investigation to adapt axial grooved designs to the gammit of heat pipe thermal control techniques, with particular emphasis on those suited for cryogenic applications was conducted. In addition to considering both active and passive gas control, diode designs utilizing liquid or gas blockage, or a liquid trap, are evaluated. The use of the liquid trap as a secondary heat pipe for forward mode operation during diode shutdown is also studied. This latter function is basically that of a thermal switch. Finally, a system capable of hybrid functions consisting of gas-controlled variable conductance and liquid trap diode shutdown or thermal switching is defined.

Source record↗
NASA NTRS1976

Parametric study of the noise produced by the interaction of the main rotor wake with the tail rotor

A model was designed, fabricated and wind tunnel tested to identify some of the parameters which were pertinent to the noise produced by the interaction of the main rotor wake with the tail rotor. The model provided for variations in many geometric and operating parameters. The initial set of tests indicated that the noise produced by the tail rotor was, in general, sensitive to the location of the vortex interaction on the tail rotor disk, direction of rotation, lateral rotor fin spacing, tip speed and the operating mode of the tail rotor; and generally insensitive to main rotor thrust coefficient, longitudinal spacing and tail rotor to main rotor rotational speed ratios. Refinements in the analyses to adequately predict the noise phenomenon have been outlined to complement further experimental investigations.

Balcerak, J. C.↗
NASA NTRS1976

Wind tunnel and ground static investigation of a large scale model of a lift/cruise fan V/STOL aircraft

An investigation was conducted in a 40 foot by 80 foot wind tunnel to determine the aerodynamic/propulsion characteristics of a large scale powered model of a lift/cruise fan V/STOL aircraft. The model was equipped with three 36 inch diameter turbotip X376B fans powered by three T58 gas generators. The lift fan was located forward of the cockpit area and the two lift/cruise fans were located on top of the wing adjacent to the fuselage. The three fans with associated thrust vectoring systems were used to provide vertical, and short, takeoff and landing capability. For conventional cruise mode operation, only the lift/cruise fans were utilized. The data that were obtained include lift, drag, longitudinal and lateral-directional stability characteristics, and control effectiveness. Data were obtained up to speeds of 120 knots at one model height of 20 feet for the conventional aerodynamic lift configuration and at several thrust vector angles for the powered lift configuration.

Source record↗
NASA NTRS1974

Simulation verification techniques study. Task report 4: Simulation module performance parameters and performance standards

Shuttle simulation software modules in the environment, crew station, vehicle configuration and vehicle dynamics categories are discussed. For each software module covered, a description of the module functions and operational modes, its interfaces with other modules, its stored data, inputs, performance parameters and critical performance parameters is given. Reference data sources which provide standards of performance are identified for each module. Performance verification methods are also discussed briefly.

Source record↗
NASA NTRS1975

ATS-6 - Flight performance of the Advanced Thermal Control Flight Experiment

The Advanced Thermal Control Flight Experiment on ATS-6 was designed to demonstrate the thermal control capability of a thermal diode (one-way) heat pipe, a phase-change material for thermal storage, and a feedback-controlled heat pipe. Flight data for the different operational modes are compared to ground test data, and the performance of the components is evaluated on an individual basis and as an integrated temperature-control system.

Kirkpatrick, J. P.↗
NASA NTRS1977

Photovoltaic system test facility electromagnetic interference measurements

Field strength measurements on a single row of panels indicates that the operational mode of the array as configured presents no radiated EMI problems. Only one relatively significant frequency band near 200 kHz showed any degree of intensity (9 muV/m including a background level of 5 muV/m). The level was measured very near the array (at 20 ft distance) while Federal Communications Commission (FCC) regulations limit spurious emissions to 15 muV/m at 1,000 ft. No field strength readings could be obtained even at 35 ft distant.

Johnson, J. A.↗
NASA NTRS1976

Identifying and analyzing methods for reducing the energy consumption of helicopters

Reductions in helicopter energy consumption can be accomplished through the use of advanced technology in the areas of powerplant design, improved rotor efficiency, reduced parasite drag, and reduced structural empty weight. Baseline helicopters incorporating technology were designed for a short range (200 n mi) and a very short haul (100 n mi) mission scenario. Parametric analyses were then conducted to determine the impact of technology improvement. Many of the parameters varied are interrelated. A summary of such interactions is presented, and some additional sensitivity values were added so that energy reduction and DOC as affected by the major technological factors or operational modes are clearly defined.

Davis, S. J.↗
NASA NTRS1977

The ATS-6 power system: Hardware implementation and orbital performance

The Applications Technology Satellite-6 power system, a shunt-boost configuration, uses partial shunt regulation of the solar array and a boost regulator for control of battery power. Regulation is provided for three different operating modes: shunt, charge, and boost. This configuration achieves the highest efficiency of power transfer from the solar array to the loads. The excellent dynamic regulation and low output impedance of the power system virtually eliminated the problem of subsystem interactions on the power bus due to conducted interference from load current fluctuations. The performance of the power system continues to be excellent. The solar array degradation (18.5 percent) was less than the specified 20 percent in two years in spite of extreme cycling from -160 C to 60 C. A unique battery cycling regime of discharges varying from 5 percent to 60 percent daily is being encountered. During the second year, noneclipse discharges have occurred twice a day to depths of 35 percent and 45 percent. Battery performance was good with only a small decrease in end-of-discharge voltage. A recent test to evaluate capacity gave 12.4 AH (83% of the nominal capacity of 15 AH) after over 1400 battery discharge cycles. A small increase in the end-of-charge voltage has recently occurred necessitating a change in the charge regime to achieve full charge conditions.

Lavigna, T. A.↗
NASA NTRS1976

The ATS-6 power system - Hardware implementation and orbital performance

The Applications Technology Satellite-6 has performed more than 20 communications, technological and scientific experiments in 2 years of highly successful operation. Contributing substantially to this success has been the flexibility of the power system that allows multiple operation of experiments. The power system, a shunt-boost configuration, uses partial shunt regulation of the solar array and a boost regulator for control of battery power. Regulation is provided for three different operating modes: shunt, charge, and boost. This configuration achieves the highest efficiency of power transfer from the solar array to the loads. The solar array degradation (18.5 percent) has been less than the predicted 20 percent in spite of extreme cycling from -160 C to 60 C. A unique battery cycling regime of discharges varying from 5 percent to 60 percent daily is being encountered. During the second year, noneclipse discharges have occurred twice a day to depths of 35 percent and 45 percent. Battery performance has been good with only a small decrease in end-of-discharge voltage.

Lavigna, T. A.↗
NASA NTRS1976

Precision pointing of the international ultraviolet explorer /IUE/ scientific instrument using a gyroscopic and stellar reference

The Attitude Control System for the IUE spacecraft is described. The basic mission objectives are stated and a sequential discussion of the mission is presented. Desired accuracy for each mission phase is noted and where applicable the onboard control mechanization is shown. Sensors and actuator systems utilized by the control algorithms are described. Finally, onboard software is discussed to a level necessary to understand the prime mission mode operation.

Moore, J. V.↗
NASA NTRS1976

A parametric model study of the noise generated by the aerodynamic interaction of the tail rotor with the wake of the main rotor

Wind tunnel tests were conducted to determine the influence of various parameters on the noise produced by the interaction of the main rotor wake with the tail rotor. Parameters found to be of significance were the location of the main rotor vortex interaction on the tail rotor disk, the direction of rotation of the tail rotor, the lateral tail rotor-fin spacing, and the operating mode of the tail rotor. Of lesser importance were the main rotor thrust coefficient, longitudinal spacing between rotors, and tail rotor-to-main rotor rotational speed ratios. Analysis of the interaction noise characteristics using a simplified representation of the aerodynamic phenomena occurring during the interaction showed that existing predictive techniques could be modified and extended to predict the pertinent noise characteristics.

White, R. P., Jr.↗
NASA NTRS1977

Extension of atomic nitrogen measurements into the lower thermosphere

Special operating modes of the open source neutral mass spectrometer (OSS) on the Atmosphere Explorer C permit the measurement of odd nitrogen (N + NO) number densities between 180 and 450 km. By using optical measurements of NO concentrations from the ultraviolet nitric oxide experiment on AE-C, number densities of N are obtained. Altitude profiles for the midlatitude legs of three orbits in the late spring of 1974 are presented and compared with densities predicted by the AE-C (OSS) empirical N model at 375 km. Atomic nitrogen appeared to be in diffusive equilibrium at least above 200 km in each of the orbits studied. A typical number density of N at 200 km, 0900 LST, and 40 deg N latitude in late May 1974 is 30 million per cu cm.

Engebretson, M. J.↗
NASA NTRS1977

Solar power satellite system definition study. Part 2, volume 8: SPS launch vehicle ascent and entry sonic overpressure and noise effects

Recoverable launch vehicle concepts for the Solar Power Satellite program were identified. These large launch vehicles are powered by proposed engines in the F-1 thrust level class. A description of the candidate launch vehicles and their operating mode was provided. Predictions of the sonic over pressures during ascent and entry for both types of vehicles, and prediction of launch noise levels in the vicinity of the launch site were included. An overall assessment and criteria for sonic overpressure and noise levels was examined.

Source record↗
NASA NTRS1977

Prototype solar heating and hot water systems

Alternative approaches to solar heating and hot water system configurations were studied, parametrizing the number and location of the dampers, the number and location of the fans, the interface locations with the furnace, the size and type of subsystems, and operating modes. A two-pass air-heating collector was selected based on efficiency and ease of installation. Also, an energy transport module was designed to compactly contain all the mechanical and electrical control components. System performance calculations were carried out over a heating season for the tentative site location at Tunkhnana, Pa. Results illustrate the effect of collector size, storage capacity, and use of a reflector. Factors which affected system performance include site location, insulative quality of the house, and of the system components. A preliminary system performance specification is given.

Source record↗
NASA NTRS1978

Planned flight test of a mercury ion auxiliary propulsion system. 1: Objectives, systems descriptions, and mission operations

A planned flight test of an 8 cm diameter, electron-bombardment mercury ion thruster system is described. The primary objective of the test is to flight qualify the 5 mN (1 mlb.) thruster system for auxiliary propulsion applications. A seven year north-south stationkeeping mission was selected as the basis for the flight test operating profile. The flight test, which will employ two thruster systems, will also generate thruster system space performance data, measure thruster-spacecraft interactions, and demonstrate thruster operation in a number of operating modes. The flight test is designated as SAMSO-601 and will be flown aboard the shuttle-launched Air Force space test program P80-1 satellite in 1981. The spacecraft will be 3- axis stabilized in its final 740 km circular orbit, which will have an inclination of approximately greater than 73 degrees. The spacecraft design lifetime is three years.

Power, J. C.↗
NASA NTRS1977

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

Extended operation of a small process-development unit routinely produced high quality silane in 97+% yield from dichlorosilane. The production rate was consistent with design loadings for the fractionating column and for the redistribution reactor. A glass fluid-bed reactor was constructed for room temperature operation. The behavior of a bed of silcon particles was observed as a function of various feedstocks, component configurations, and operating conditions. For operating modes other than spouting, the bed behaved in an erratic and unstable manner. A method was developed for casting molten silicon powder into crack-free solid pellets for process evaluation. The silicon powder was melted and cast into thin walled quartz tubes that sacrificially broke on cooling.

Breneman, W. C.↗