Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Plasma uniformity and phase-controlled etching in a very high frequency capacitive discharge

The influence of controlled phase shift between very high frequency (100 MHz) voltages applied to the powered electrodes on the plasma uniformity and etch rate was studied in a capacitive triode-type reactor. Radial profiles of plasma optical emission were measured as a function of the phase shift in process (C{sub 4}F{sub 8}/O{sub 2}/Ar) plasma with the low frequency bias power both turned off and on. Radial profiles of KrF photoresist etch rate over a 300 mm wafer were obtained in the same conditions (with the bias power turned on). Besides, plasma density at the wafer center and edge was measured versus the phase shift in pure Ar plasma. It occurred that all measured characteristics strongly depend on the phase shift and correlate with each other. It has been shown that the phase-shift control can considerably improve both the plasma and etch-rate uniformity in very high-frequency capacitive reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High Fidelity CFD Simulations Supporting the KP-FHR

Kairos Power, LLC, is developing its version of the Fluoride-cooled High-temperature Reactor, the KP-FHR. The design uses a pebble bed core with fluoride salt as a coolant. The pebbles used in the KP-FHR have a diameter of 4 cm, with a shell fuel region where TRISO particles are embedded. A Pebble bed core design is adopted by several Gen IV reactors, They boast many benefits, such as fuel integrity, highly efficient heat transfer, and passive safety. However, it is challenging to accurately predict temperature and flow inside a pebble bed. Traditional approaches use the porous media model, which regards the pebble bed as a continuous medium, but with different temperature fields representing different levels, such as the fluid temperature, pebble surface temperature, and pebble center temperature. Empirical heat transfer correlations are adopted to calculate the heat transfer coefficient between different phases. However, empirical correlations are usually validated with experimental data, which usually lacks detail inside the pebble bed. The available experimental data is also generally at a high Reynolds number, which falls outside of the conditions of KP-FHR. Explicit computational fluid dynamics (CFD) simulations of randomly packed pebble beds have only become feasible recently. This is thanks to the rapid development of computational power and scalable algorithms. In this work, we used the Spectral Element Method (SEM) CFD code NekRS to simulate the randomly packed pebble bed in a cylindrical container. NekRS, which is the GPU variant of Nek5000, but refactored to utilize the computational power of GPUs using the OCCA library to run on hybrid architecture high performance computing systems. It was initially developed with the libParamunal library, but truncated and tuned for large-scale turbulence simulation. As a result, the SEM reaches higher precision with the same degrees of freedom by using a high-order Lagrange polynomial basis distributed on Gauss-Lobatto-Legendre quadrature inside each element, compared to lower-order methods, such the Finite Volume Method and Finite Element Method. The report is divided into five parts. We start with a general discussion of the pebble bed reactor, along with a specific investigation into the KP-FHR. The second part presents the numerical methodology. In the third part, we study a modular pebble bed with 1741 pebbles in a container of 7 pebble-diameter radius. Beyond LES simulations done by NekRS, we also leveraged the thermal radiation model in OpenFOAM to study heat transfer under no-forced-flow scenarios. Then, in the fourth part we simulated a pebble bed similar to the size of the Hermes Test Reactor. The total number of pebbles is in these simulations is 34,374. The container radius is 14 pebble-diameters. Finally, the report concludes in part five, with a discussion of future work.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutron diffraction and electrical transport studies on magnetic ordering in terbium at high pressures and low temperatures

Neutron diffraction and electrical transport measurements have been carried out on the heavy rare earth metal terbium at high pressures and low temperatures in order to elucidate the onset of ferromagnetic order as a function of pressure. The electrical resistance measurements show a change in slope as the temperature is lowered through the ferromagnetic Curie temperature. The temperature of this ferromagnetic transition decreases from approximately 240 K at ambient pressure at a rate of –16.7 K/GPa up to a pressure of 3.6 GPa, at which point the onset of ferromagnetic order is suppressed. Neutron diffraction measurements as a function of pressure at temperatures ranging from 90 K to 290 K confirm that the change of slope in the resistance is associated with the ferromagnetic ordering, since this occurs at pressures similar to those determined from the resistance results at these temperatures. Furthermore, a change in ferromagnetic ordering as the pressure is increased above 3.6 GPa is correlated with the phase transition from the ambient hexagonal close packed (hcp) structure to an α-Sm type structure at high pressures.

36 MATERIALS SCIENCE↗

Two-dimensional Anderson-Hubbard model in the DMFT + {Sigma} approximation

The density of states, the dynamic (optical) conductivity, and the phase diagram of the paramagnetic two-dimensional Anderson-Hubbard model with strong correlations and disorder are analyzed within the generalized dynamical mean field theory (DMFT + {Sigma} approximation). Strong correlations are accounted by the DMFT, while disorder is taken into account via the appropriate generalization of the self-consistent theory of localization. We consider the two-dimensional system with the rectangular 'bare' density of states (DOS). The DMFT effective single-impurity problem is solved by numerical renormalization group (NRG). The 'correlated metal,' Mott insulator, and correlated Anderson insulator phases are identified from the evolution of the density of states, optical conductivity, and localization length, demonstrating both Mott-Hubbard and Anderson metal-insulator transitions in two-dimensional systems of finite size, allowing us to construct the complete zero-temperature phase diagram of the paramagnetic Anderson-Hubbard model. The localization length in our approximation is practically independent of the strength of Hubbard correlations. But the divergence of the localization length in a finite-size two-dimensional system at small disorder signifies the existence of an effective Anderson transition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical/electrical correlations in ZnO. The plasmonic resonance phase diagram

The Drude equation for dielectric constant ϵ(E) depends on four parameters: ϵ∞, effective mass m*, optical mobility µopt, and optical carrier concentration nopt. By solving this equation at ϵ(Eres)=0, we obtain a relationship between µopt and nopt at constant plasmonic resonance energy Eres [or wavelength λres (µm)=1.2395/Eres (eV)]. A family of µopt versus nopt curves covering a range of λres values (including the limiting wavelength λres=∞) constitutes a plasmonic resonance phase diagram (PRPD) for a semiconductor defined by only ϵ∞ and m*. The PRPD is a convenient instrument that allows an immediate prediction of λres from Hall-effect measurements of µH and nH. We apply the PRPD analysis to a series of ten ZnO samples grown by pulsed laser deposition at 200°C in an ambient of 33%H2:67%Ar and annealed in 25°C steps for 10 min in air at various temperatures from 400 to 600°C. For the samples annealed at 550°C or lower, the µH/nH points yield predicted values of λres that range from 1.07 to 2.80 µm; however, the 575 and 600°C samples are predicted to have no resonance at all. Reflectance curves for the eight samples annealed up to 550 °C decrease slowly from 6 eV down to about Eres= 0.5–1.15 eV, and then increase rapidly for E < Eres. In contrast, there is no such resonance-related increase for the 575 and 600 °C samples. Satisfactory agreement is found between the reflectance minima and the Hall-effect-predicted values of λres.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Structural investigation of K{sub x}Ba{sub 1-x}Ga{sub 2-x}Ge{sub 2+x}O{sub 8} solid solutions using the X-ray Rietveld method

The K{sub x}Ba{sub 1-x}Ga{sub 2-x}Ge{sub 2+x}O{sub 8} (x=0.6-1.0) solid solutions undergo a structural phase transition that has a significant effect on their sintering behavior and their microwave dielectric properties. The crystal structures of both phases within the solid-solution region were determined by the Rietveld method using powder X-ray diffraction data. We found that the low-temperature-stable phase is isostructural with the pseudo-orthorhombic KGaGe{sub 3}O{sub 8} (space group P2{sub 1}/a), while the high-temperature-stable phase has a typical monoclinic feldspar structure (space group C2/m). Due to the topological differences between the two structures, the T-O bonds within the tetrahedra must be partially recombined to make a new framework, which causes an endothermic effect during the P2{sub 1}/a to C2/m phase transition. The correlation between the crystal structures, the microwave dielectric properties and the phase-transition behaviors were discussed in terms of the crystallographic features, the lattice parameters, and the strain-induced anisotropic peak-broadening. - Graphical abstract: The K{sub x}Ba{sub 1-x}Ga{sub 2-x}Ge{sub 2+x}O{sub 8} (x=0.6-1.0) solid solutions undergo a structural phase transition. The crystal structures of both phases within the solid-solution region were determined by the Rietveld method using powder X-ray diffraction data. The topological analogy between the two structures is seen by comparing the (001) projections of the low phase structure (left) and the (201-bar) projection of the high phase structure (right).

36 MATERIALS SCIENCE↗

Transition to the Haldane phase driven by electron-electron correlations

One of the most famous quantum systems with topological properties, the spin S = 1 antiferromagnetic Heisenberg chain, is well-known to display exotic S = 1/2 edge states. However, this spin model has not been analyzed from the more general perspective of strongly correlated systems varying the electron electron interaction strength. Here, we report the investigation of the emergence of the Haldane edge in a system of interacting electrons – the two orbital Hubbard model—with increasing repulsion strength U and Hund interaction J H . We show that interactions not only form the magnetic moments but also form a topologically nontrivial fermionic many-body ground-state with zero-energy edge states. Specifically, upon increasing the strength of the Hubbard repulsion and Hund exchange, we identify a sharp transition point separating topologically trivial and nontrivial ground-states. Surprisingly, such a behaviour appears already at rather small values of the interaction, in a regime where the magnetic moments are barely developed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Communication: An effective linear-scaling atomic-orbital reformulation of the random-phase approximation using a contracted double-Laplace transformation

An atomic-orbital (AO) reformulation of the random-phase approximation (RPA) correlation energy is presented allowing to reduce the steep computational scaling to linear, so that large systems can be studied on simple desktop computers with fully numerically controlled accuracy. Our AO-RPA formulation introduces a contracted double-Laplace transform and employs the overlap-metric resolution-of-the-identity. First timings of our pilot code illustrate the reduced scaling with systems comprising up to 1262 atoms and 10 090 basis functions. .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Correlation between ferroelectricity and ferroelectric orthorhombic phase of Hf x Zr 1-x O 2 thin films using synchrotron x-ray analysis

The change in the interplanar spacing ( d -spacing) including the ferroelectric orthorhombic (O) phase in the low-temperature fabricated Hf x Zr 1-x O 2 (HZO) films was studied using synchrotron grazing-incidence wide-angle x-ray scattering analysis. The 10-nm-thick HZO films were fabricated by thermal and plasma-enhanced atomic layer deposition (TH- and PE-ALD) methods using H 2 O gas and O 2 plasma as oxidants, respectively, and a post-metallization annealing (PMA) was performed at 300–400 °C. The d -spacing of the mixture of (111)-, (101)-, and (111)-planes of O, tetragonal (T), and cubic (C) phases, respectively, for the TH- and PE-ALD HZO films increased up to 2.99 Å with an increase in PMA temperature, while the d -spacing estimated by conventional x-ray diffraction was 2.92 Å regardless of the PMA temperature. The remanent polarization (2 P r = P r + - P r - ) of the HZO films increased as the PMA temperature increased. It is clear that the 2 P r value satisfied a linear relationship as a function of the d -spacing of O(111)/T(101)/C(111) phases. Furthermore, the wake-up effect was found to depend on the ferroelectric O phase formation. The wake-up effect was significantly reduced in both the TH- and PE-ALD HZO films after the PMA at 400 °C due to the increase in the ferroelectric O phase formation. The leakage current density ( J )–electric field properties of the PE-ALD HZO film with the lowest d -spacing were divided into three steps, such as low, middle, and large J values, in the wake-up (10 3 cycles), pristine (10 0 cycle), and fatigue (10 7 cycles) states, respectively. Therefore, an analysis of the ferroelectric O phase is very important for understanding the ferroelectricity including endurance.

36 MATERIALS SCIENCE↗

Random fields from quenched disorder in an archetype for correlated electrons: The parallel spin stripe phase of La 1.6 – x Nd 0.4 Sr x CuO 4 at the 1/8 anomaly

The parallel stripe phase is remarkable both in its own right, and in relation to the other phases with which it coexists. Its inhomogeneous nature makes such states susceptible to random fields from quenched magnetic vacancies. Here we argue this is the case by introducing low concentrations of nonmagnetic Zn impurities (0%–10%) into La 1.6–x ⁢Nd 0.4⁢ Sr x ⁢CuO 4 (Nd-LSCO) with x=0.125 in single-crystal form, well below the percolation threshold of ~41% for a two-dimensional square lattice. Elastic neutron scattering measurements on these crystals show clear magnetic quasi-Bragg peaks at all Zn dopings. While all the Zn-doped crystals display order parameters that merge into each other and the background at ~68 K, the temperature dependence of the order parameter as a function of Zn concentration is drastically different. This result is consistent with meandering charge stripes within the parallel stripe phase, which are pinned in the presence of quenched magnetic vacancies. In turn it implies vacancies that preferentially occupy sites within the charge stripes, and hence that can be very effective at disrupting superconductivity in Nd-LSCO (x=0.125), and, by extension, in all systems exhibiting parallel stripes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Gravitational-wave signature of core-collapse supernovae

Here, we calculate the gravitational-wave (GW) signatures of detailed 3D core-collapse supernova sim ulations spanning a range of massive stars. Most of the simulations are carried out to times late enough to capture more than 95% of the total GW emission. We find that the f/g-mode and f-mode of proto-neutron star oscillations carry away most of the GW power. The f-mode frequency inex orably rises as the proto-neutron star (PNS) core shrinks. We demonstrate that the GW emission is excited mostly by accretion plumes onto the PNS that energize modal oscillations and also high frequency (“haze”) emission correlated with the phase of violent accretion. The duration of the major phase of emission varies with exploding progenitor and there is a strong correlation between the total GW energy radiated and the compactness of the progenitor. Moreover, the total GW emissions vary by as much as three orders of magnitude from star to star. For black-hole formation, the GW signal tapers off slowly and does not manifest the haze seen for the exploding models. For such failed models, we also witness the emergence of a spiral shock motion that modulates the GW emission at a frequency near ~100 Hertz that slowly increases as the stalled shock sinks. We find significant angular anisotropy of both the high- and low-frequency (memory) GW emissions, though the latter have very little power.

79 ASTRONOMY AND ASTROPHYSICS↗

Effect of surface oxidation on the onset of nucleate boiling in a materials test reactor coolant channel

The onset of nucleate boiling (ONB) serves as the thermal-hydraulic operating limit for many research and test reactors. However, boiling incipience under forced convection has not been well-characterized in narrow channel geometries or for oxidized surface conditions. This study presents experimental data for the ONB in vertical upflow of deionized (DI) water in a simulated materials test reactor (MTR) coolant channel. The channel gap thickness and aspect ratio were 1.96 mm and 29:1, respectively. Boiling surface conditions were carefully controlled and characterized, with both heavily oxidized and native oxide surfaces tested. Measurements were performed for mass fluxes ranging from 750 to 3000 kg/m 2 s and for subcoolings ranging from 10 to 45°C. ONB was identified using a combination of high-speed visual observation, surface temperature measurements, and channel pressure drop measurements. Surface temperature measurements were found to be most reliable in identifying the ONB. For the nominal (native oxide) surface, results indicate that the correlation of Bergles and Rohsenow, when paired with the appropriate single-phase heat transfer correlation, adequately predicts the ONB heat flux. Furthermore, incipience on the oxidized surface occurred at a higher heat flux and superheat than on the plain surface.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Swelling and Helium Bubble Morphology in a Cryogenically Treated FeCrNi Alloy with Martensitic Transformation and Reversion after Helium Implantation

A cryo-quenched 70 wt % Fe-15 wt% Cr-15 wt% Ni single-crystal alloy with fcc (face centered cubic), bcc (body centered cubic), and hcp (hexagonal close packed) phases was implanted with 200 keV He+ ions up to 2 × 1017 ions·cm -2 at 773 K. Surface-relief features were observed subsequent to the He+ ion implantation, and transmission electron microscopy was used to characterize both the surface relief properties and the details of associated “swelling effects” arising cumulatively from the austenitic-to-martensitic phase transformation and helium ion-induced bubble evolution in the single-crystal ternary alloy. The bubble size in the bcc phase was found to be larger than that in the fcc phase, while the bubble density in the bcc phase was correspondingly lower. The phase boundaries with misfit dislocations formed during the martensitic transformation and reversion processes served as helium traps that dispersed the helium bubble distribution. Swelling caused by the phase transformation in the alloy was dominant compared to that caused by helium bubble formation due to the limited depth of the helium ion implantation. The detailed morphology of helium bubbles formed in the bcc, hcp, and fcc phases were compared and correlated with the characters of each phase. The helium diffusion coefficient under irradiation at 773 K in the bcc phase was much higher (i.e., by several orders of magnitude) than that in the fcc phase and led to faster bubble growth. Moreover, the misfit phase boundaries were shown to be effective sites for the diffusion of helium atoms. This feature may be considered to be a desirable property for improving the radiation tolerance of the subject, ternary alloy.

36 MATERIALS SCIENCE↗

Periodic Narrowband Radio Wave Emissions and Inward Plasma Transport at Saturn's Magnetosphere

The abrupt brightening of an Energetic Neutral Atom (ENA) blob or cloud has been interpreted as plasma injection in the Kronian magnetosphere (termed ENA injection herein). Morphologically, there appears to be two types of abrupt ENA cloud brightening: (1) the brightening of a large cloud usually seen at distances >10–12 R {sub s} (R {sub s} ∼ 60,268 km) in the midnight or postmidnight region; (2) the brightening of a smaller cloud usually seen at distances <10–12 R {sub s} around 21–03 magnetic local time. Among many radio waves observed at Saturn, type 2 ENA injections correlate best with the 5 kHz narrowband (NB) waves. Using Cassini Ion and Neutral Camera (INCA) and Radio and Plasma Wave Science (RPWS) data, we examine the periodicities of the type 2 ENA injections and the 5 kHz NB emissions as well as their cross-correlations, which have been previously used to measure the lag times or phase differences. Because correlational analysis can only establish linear relationships, we also use mutual information to establish linear and nonlinear relationships. On average, the peak of the 5 kHz NB emission lags those of the type 2 ENA injection by about a few minutes to 2 hr. The injection of hot plasma to the inner magnetosphere can lead to temperature anisotropy, which can generate electrostatic upper hybrid waves, which upon encountering the high-density gradient at the outer edge of the Enceladus density torus, can mode convert to Z mode and then to O mode. The 5 kHz NB waves commonly propagate in the O mode.

79 ASTRONOMY AND ASTROPHYSICS↗

The role of the spatial heterogeneity and correlation length of surface wettability on two-phase flow in a CO 2 -water-rock system

This study characterized and modeled heterogeneous surface wettability in sandstone and investigated the role of spatial heterogeneity and correlation length of surface wettability on relative permeability in a supercritical CO 2 (scCO 2 )-brine-rock system. Understanding the role of wettability heterogeneity on relative permeability is essential to geological CO 2 sequestration, oil and gas recovery, and contaminated groundwater remediation. Although numerous studies have attempted to understand the influences of surface wettability, capillary number (Ca), and viscosity ratio, the role of the spatial variation and correlation length of surface wettability on two-phase flow in three-dimensional (3D) porous media has not been unraveled due to the challenges in the measurement and representation of realistic rock surface wettability. In this work, we conducted in-situ measurements of surface contact angle (CA) in a Bentheimer sandstone after CO 2 flooding using micro-computed tomography (micro-CT), and found that the pore-scale CA distribution on rock surfaces followed a log-normal distribution associated with a spatial correlation length. Based on the statistical information from CT scanning, a Gaussian random field was used to model CA distributions that had desired standard deviations and spatial correlation lengths, which were then adjusted within a certain range of values for sensitivity analyses to study their combined effects on the two-phase flow in the porous medium using the lattice Boltzmann (LB) method. The LB two-phase flow simulation was accelerated using hybrid, multicore parallel computing to overcome the challenges in simulating multiphase flow in a large 3D domain having 800 × 800 × 600 nodes. The simulation results showed that the surface wettability heterogeneity (i.e., standard deviation of CA) had a lesser effect on the relative permeability of the wetting fluid (water) but a more significant impact on the relative permeability of the non-wetting fluid (scCO 2 ). The Corey model was used to fit the LB-simulated relative permeability curves of water and scCO 2 and showed that the variations in the relative permeability curves for both water and scCO 2 increased as the standard deviation and spatial correlation length of CA increased. This study illustrated that the assumption of homogeneous surface wettability may cause errors in multiphase flow simulations. Furthermore, the impacts of both the standard deviation and spatial correlation length of CAs should be accounted for. This is the first study that explored the spatial correlation lengths associated with CA distributions on sandstone surfaces and comprehensively investigated the roles of both spatial variation and correlation length of CA on two-phase flow properties in 3D porous media. The optimized LB multiphase flow model was proved a powerful tool to study the interplays and combined effects of these statistical parameters, which had critical applications in numerous natural and engineering processes that involved multiphase flow in porous media.

58 GEOSCIENCES↗