SEARCH · Search NASA

Results for “REINFORCING FIBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Performance of graphite fiber-reinforced polyimide composites in self-aligning plain bearings to 315 C

A 50/50 (weight percent) composite of graphite fibers and polyimide was studied in self-aligning plain bearings oscillating + or - 15 degrees at 1 hz. The friction coefficient was 0.15 + or - 0.05 at 250 C, and 0.05 + or - 0.02 at 315 C. Best results were obtained with a molded composite liner with chopped graphite fibers randomly oriented in the composite. The specific wear rate is given. It was found that the dynamic unit load capacity was higher for a composite bushing (thin liner), than for a composite ball.

Sliney, H. E.↗

NASA NTRS1994

Continuous unidirectional fiber reinforced composites: Fabrication and testing

The study of the anisotropic mechanical properties of an inexpensively fabricated composite with continuous unidirectional fibers and a clear matrix was investigated. A method has been developed to fabricate these composites with aluminum fibers and a polymer matrix. These composites clearly demonstrate the properties of unidirectional composites and cost less than five dollars each to fabricate.

Weber, M. D.↗

DOE OSTI2022

Self-Sensing Fiber Reinforced Composite (CRADA Final Report)

The project aimed to demonstrate a scalable coating process to adhere nanoparticles to the surface of fibers and fabricate composites with in-situ damage detection abilities and simultaneous mechanical performance enhancements. Carbon fiber (CF) composites have the inherent problem of hiding damage within the structure with no visual indications on the surface. Therefore, a technique to monitor for damage or excessive stress on the composite is necessary to ensure its safety and avoid catastrophic failure. This capability will be desired in future transportation vehicle designs, such as in cargo and surveillance drones developed by Dronesat, LLC, (Dronesat) who was the industrial partner on this project.

36 MATERIALS SCIENCE↗

NASA NTRS1974

Penny-shaped crack in a fiber-reinforced matrix

Using a slender inclusion model developed earlier, the elastostatic interaction problem between a penny-shaped crack and elastic fibers in an elastic matrix is formulated. For a single set and for multiple sets of fibers oriented perpendicularly to the plane of the crack and distributed symmetrically on concentric circles, the problem was reduced to a system of singular integral equations. Techniques for the regularization and for the numerical solution of the system are outlined. For various fiber geometries numerical examples are given, and distribution of the stress intensity factor along the crack border was obtained. Sample results showing the distribution of the fiber stress and a measure of the fiber-matrix interface shear are also included.

Narayanan, T. V.↗

NASA NTRS1975

Penny-shaped crack in a fiber-reinforced matrix

Using the slender inclusion model developed earlier the elastostatic interaction problem between a penny-shaped crack and elastic fibers in an elastic matrix is formulated. For a single set and for multiple sets of fibers oriented perpendicularly to the plane of the crack and distributed symmetrically on concentric circles the problem is reduced to a system of singular integral equations. Techniques for the regularization and for the numerical solution of the system are outlined. For various fiber geometries numerical examples are given and distribution of the stress intensity factor along the crack border is obtained. Sample results showing the distribution of the fiber stress and a measure of the fiber-matrix interface shear are also included.

Narayanan, T. V.↗

NASA NTRS1979

A review of issues and strategies in nondestructive evaluation of fiber reinforced structural composites

The need for advanced nondestructive evaluation (NDE) techniques for quantitative assessment of the mechanical strength and integrity of fiber composites during manufacture and service and following repair operations is stressed. The discussion covers problems and different approaches in regard to acceptance criteria, calibration standards, and methods for NDE of composites in strength critical applications. Finally, it is concluded that acousto-ultrasonic techniques provide the 'methods of choice' in this area.

Vary, A.↗

NASA NTRS1982

Modelling of dimensional stability of fiber reinforced composite materials

Various methods of predicting the expansion and diffusion properties of composite laminates are reviewed. The prediction equations for continuous fiber composites can be applied to SMC composites as the effective fiber aspect ratio in the latter is large enough. The effect of hygrothermal expansion on the dimensional stability of composite laminates was demonstrated through the warping of unsymmetric graphite/epoxy laminates. The warping is very sensitive to the size of the panel, and to the moisture content which is in turn sensitive to the relative humidity in the environment. Thus, any long term creep test must be carried out in a humidity-controlled environment. Environmental effects in SMC composites and bulk polyester were studied under seven different environments. The SMC composites chosen are SMC-R25, SMC-R40, and SMC-R65.

Hahn, H. T.↗

NASA NTRS1991

Chemical compatibility issues related to use of copper as an interfacial layer for SiC fiber reinforced Ti3Ai+Nb composite

The reaction of Cu, a potential interfacial compliant layer for the Ti3Al plus Nb/SiC composite, with SiC, SCS-6 fiber, and the Ti3Al plus Nb matrix was examined at two temperatures: 1223 and 1273 K. Reaction of Cu with SiC resulted in the formation of a CuSi solution and free carbon, the reaction product being molten at 1273 K. Hot pressing the SCS-6 fiber in a Cu matrix at 1273 K resulted in cracking and delamination of the outer carbon-rich coating, thus allowing the Cu to penetrate to the SiC-carbon coating interface and react with SiC. In contrast, no such damage to the outer coating was observed at 1223 K. There was excessive reaction between Cu and the Ti3Al plus Nb matrix, the reaction product being molten both at 1223 and 1273 K. An interlayer of Nb between Cu and Ti3Al plus Nb matrix prevented the reaction between the two.

Misra, Ajay K.↗

NASA NTRS1983

Surface analysis of grapite fiber reinforced polyimide composites. I

The results of experimental analyses of the effects of pretreatment on bonding between composite materials are reported. The materials comprised graphite fibers in a polyimide matrix. The surfaces were bonded as-received or subjected to grit blasting, bead blasting, hand sanding, washes with ethanolic KOH, NH2NH2-H2O or H2SO4 + 0.30 H2O2 or flashblasting. SEM and X-ray photoelectron spectroscopy revealed fluorine contents in the as-received samples. Contact angles were determined by means of five different liquids with various surface tensions. The flashblast technique removed all fluorine from the samples. Low critical surface tensions were found in the composite surfaces with high fluorine concentrations. The surface scanning techniques are concluded to be useful for studying factors influencing the strength and durability of adhesively bonded composites.

Messick, D. L.↗

NASA NTRS1965

Research on fiber-reinforced composites

Research in materials science - high temperature structural materials, wetting and adherence of nickel alloys to sapphire, boron carbide filaments, and ceramic and graphite fibers

MATERIALS SCIENCE↗

NASA NTRS1974

Compressive strength of fiber reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes, and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed, delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗

NASA NTRS1975

Compressive strength of fiber-reinforced composite materials

Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed - delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

Davis, J. G., Jr.↗

NASA NTRS1980

Environmental effects on graphite fiber reinforced PMR-15 polyimide

Studies were conducted to establish the effects of thermo-oxidative and hydrothermal exposure on the mechanical properties of T300 graphite fabric reinforced PMR-15 composites. The effects of hydrothermal exposure on the mechanical properties of HTS-2 continuous graphite fiber composites were also investigated. The thermo-oxidative stability characteristics of T300 fabric and T300 fabric/PMR-15 composites were determined. Flexural strengths of specimens were determined. The useful lifetime of T300 fabric/PMR-15 composites in air at 316 C was found to be about 100 hours. The useful lifetimes in air at 228 and 260 C were determined to be 500 and 1000 hours, respectively. Absorbed moisture was found to reduce the elevated temperature properties of both the T300 fabricate and HTS-2 continuous fiber composites. The moisture effect was found to be reversible.

Serafini, T. T.↗

NASA NTRS1982

Environmental effects on graphite fiber reinforced PMR-15 polyimide

Serafini, T. T.↗

NASA NTRS1998

Method of Manufacturing Carbon Fiber Reinforced Carbon Composite Valves

A method for forming a carbon composite valve for internal combustion engines is discussed. The process includes the steps of braiding carbon fiber into a rope thereby forming a cylindrically shaped valve stem portion and continuing to braid said fiber while introducing into the braiding carbon fiber rope a carbon matrix plug having an outer surface in a net shape of a valve head thereby forming a valve head portion. The said carbon matrix plug acting as a mandrel over which said carbon fiber rope is braided, said carbon fiber rope and carbon matrix plug forming a valve head portion suitable for mating with a valve seat; cutting said braided carbon valve stem portion at one end to form a valve tip and cutting said braided carbon fiber after said valve head portion to form a valve face and thus provide a composite valve preform; and densifying said preform by embedding the braided carbon in a matrix of carbon to convert said valve stem portion to a valve stem and said valve head portion to a valve head thereby providing said composite valve.

Rivers, H. Kevin↗

NASA NTRS1983

Surface analysis of graphite fiber reinforced polyimide composites

Several techniques have been used to establish the effect of different surface pretreatments on graphite-polyimide composites. Composites were prepared from Celion 6000 graphite fibers and the polyimide LARC-160. Pretreatments included mechanical abrasion, chemical etching and light irradiation. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were used in the analysis. Contact angle of five different liquids of varying surface tensions were measured on the composites. SEM results showed polymer-rich peaks and polymer-poor valleys conforming to the pattern of the release cloth used durng fabrication. Mechanically treated and light irradiated samples showed varying degrees of polymer peak removal, with some degradation down to the graphite fibers. Minimal changes in surface topography were observed on concentrations of surface fluorine even after pretreatment. The light irradiation pretreatment was most effective at reducing surface fluorine concentrations whereas chemical pretreatment was the least effective. Critical surface tensions correlated directly with the surface fluorine to carbon ratios as calculated from XPS.

Messick, D. L.↗

NASA NTRS1994

Low pressure process for continuous fiber reinforced polyamic acid resin matrix composite laminates

A low pressure processor was developed for preparing a well-consolidated polyimide composite laminate. Prepreg plies were formed from unidirectional fibers and a polyamic acid resin solution. Molding stops were placed at the sides of a matched metal die mold. The prepreg plies were cut shorter than the length of the mold in the in-plane lateral direction and were stacked between the molding stops to a height which was higher than the molding stops. The plies were then compressed to the height of the stops and heated to allow the volatiles to escape and to start the imidization reaction. After removing the stops from the mold, the heat was increased and 0 - 500 psi was applied to complete the imidization reaction. The heat and pressure were further increased to form a consolidated polyimide composite laminate.

Druyun, Darleen A.↗

NASA NTRS2011

Fabrication and Characterization of Multi-Walled Carbon Nanotube (MWCNT) and Ni-Coated Multi-Walled Carbon Nanotube (Ni-MWCNT) Repair Patches for Carbon Fiber Reinforced Composite Systems

Multi-walled carbon nanotube (MWCNT)/epoxy and nickel-coated multi-walled carbon nanotube (Ni-MWCNT)/epoxy systems were fabricated into carbon fiber composite repair patches via vacuum resin infusion. Two 4 ply patches were manufactured with fiber orientations of [90/ 90/ 4590] and [0/90/ +45/ -45]. Prior to resin infusion, the MWCNT/Epoxy system and NiMWCNT/ epoxy systems were optimized for dispersion quality. Scanning electron microscopy (SEM) and optical microscopy (OM) were used to determine the presence ofcarbon nanotubes and assess dispersion quality. Decomposition temperatures were determined via thermogravametric analysis (TGA). SEM and TGA were also used to evaluate the composite repair patches.

Johnson, Brienne↗