Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rockets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Computational simulation of liquid rocket injector anomalies

A computer model has been developed to analyze the three-dimensional two-phase reactive flows in liquid fueled rocket combustors. The model is designed to study the influence of liquid propellant injection nonuniformities on the flow pattern, combustion and heat transfer within the combustor. The Eulerian-Lagrangian approach for simulating polidisperse spray flow, evaporation and combustion has been used. Full coupling between the phases is accounted for. A nonorthogonal, body fitted coordinate system along with a conservative control volume formulation is employed. The physical models built into the model include a kappa-epsilon turbulence model, a two-step chemical reaction, and the six-flux radiation model. Semiempirical models are used to describe all interphase coupling terms as well as chemical reaction rates. The purpose of this study was to demonstrate an analytical capability to predict the effects of reactant injection nonuniformities (injection anomalies) on combustion and heat transfer within the rocket combustion chamber. The results show promising application of the model to comprehensive modeling of liquid propellant rocket engines.

Przekwas, A. J.↗
NASA NTRS1986

Acceleration effects in solid propellant rocket motors

The performance variations due to acceleration loads imposed on spinning solid propellant rocket motors are investigated. The four potentially most significant modes of acceleration-induced phenomena are identified from a study of the literature and modeled. The four modes are a mechanical mode which deals with deformations of the propellant and case: a thermodynamic mode which covers acceleration-induced combustion phenomena; a stress mode which covers the stressed propellant's effect on burn rate; and a gas dynamic mode which deals with changes in gas flow in the chamber and through the nozzle. Simplified models of each mode are developed or taken from the literature and are added to an internal ballistics evaluation computer program. The resulting analysis is the first to include all of the modes. In order to do this an original analysis of the mechanical and stress modes was necessary. However, the analysis shows that the stress mode is not important for the circular perforated grains studied. The other effects are shown to have a significant influence on solid rocket motor performance. The magnitude of the different mode effects are such that one may not be ignored over the others as has been done in the past. The results of the analysis are compared to published rocket motor data. The comparisons indicate an erosive burning effect that is a function of spin rate. A qualitative explanation of the erosive effect is presented.

Langhenry, M. T.↗
NASA NTRS1987

Comparison of theoretical and experimental thrust performance of a 1030:1 area ratio rocket nozzle at a chamber pressure of 2413 kN/m2 (350 psia)

The joint Army. Navy, NASA. Air Force (JANNAF) rocket engine peformnace prediction procedure is based on the use of various reference computer programs. One of the reference programs for nozzle analysis is the Two-Dimensional Kinetics (TDK) Program. The purpose of this report is to calibrate the JANNAF procedure incorporated into the December l984 version of the TDK program for the high-area-ratio rocket engine regime. The calibration was accomplished by modeling the performance of a 1030:1 rocket nozzle tested at NASA Lewis Research Center. A detailed description of the experimental test conditions and TDK input parameters is given. The results show that the computer code predicts delivered vacuum specific impulse to within 0.12 to 1.9 percent of the experimental data. Vacuum thrust coefficient predictions were within + or - 1.3 percent of experimental results. Predictions of wall static pressure were within approximately + or - 5 percent of the measured values. An experimental value for inviscid thrust was obtained for the nozzle extension between area ratios of 427.5 and 1030 by using an integration of the measured wall static pressures. Subtracting the measured thrust gain produced by the nozzle between area ratios of 427.5 and 1030 from the inviscid thrust gain yielded experimental drag decrements of 10.85 and 27.00 N (2.44 and 6.07 lb) for mixture ratios of 3.04 and 4.29, respectively. These values correspond to 0.45 and 1.11 percent of the total vacuum thrust. At a mixture ratio of 4.29, the TDK predicted drag decrement was 16.59 N (3.73 lb), or 0.71 percent of the predicted total vacuum thrust.

Smith, Tamara A.↗
NASA NTRS1987

Active vehicle charging measurements in sounding rocket and space shuttle orbiter environments at Low Earth Orbit (LEO) altitude

It was concluded that for electron beam emission up to 100mA, vehicle charging is not a significant problem with the Space Shuttle Orbiter. Similarly, sounding rocket payloads have no serious charging problems up to this level of beam current, provided that the maximum amount of the rocket skin is available to collect ionospheric electrons from the LEO altitude range. However, sounding rockets are marginal in their collecting area capability and other effects may occur to balance the beam current when operated at lower altitudes during the night.

Raitt, W. J.↗
NASA NTRS1987

A detailed description of the uncertainty analysis for High Area Ratio Rocket Nozzle tests at the NASA Lewis Research Center

A preliminary uncertainty analysis has been performed for the High Area Ratio Rocket Nozzle test program which took place at the altitude test capsule of the Rocket Engine Test Facility at the NASA Lewis Research Center. Results from the study establish the uncertainty of measured and calculated parameters required for the calculation of rocket engine specific impulse. A generalized description of the uncertainty methodology used is provided. Specific equations and a detailed description of the analysis are presented. Verification of the uncertainty analysis model was performed by comparison with results from the experimental program's data reduction code. Final results include an uncertainty for specific impulse of 1.30 percent. The largest contributors to this uncertainty were calibration errors from the test capsule pressure and thrust measurement devices.

Kenneth J. Davidian↗
NASA NTRS1986

Results from a series of US/Japan tethered rocket experiments

Tethered rocket experiments have been carried out four times during a US-Japan joint space program in progress since 1980. The goal of the rocket program has been to perform a new type of active experiment by ejecting an electron beam from the tethered mother-daughter payload system. In the third and fourth rocket flights, the conductive tether wire was deployed more than 400 m. It was found that the tether wire acted as an antenna and its antenna impedance decreased with the extension of the wire both in HF and VLF bands. The vehicle charging due to the beam emission up to 80 mA was repeatedly measured in the series of the experiments. During the 80 mA emission, a clear evidence for the ignition of a beam plasma discharge was obtained by the plasma probe, photometers and wave receivers.

Sasaki, S.↗
NASA NTRS1987

Comparison of theoretical and experimental thrust performance of a 1030:1 area ratio rocket nozzle at a chamber pressure of 2413 kN/sq m (350 psia)

The Joint Army, Navy, NASA, Air Force (JANNAF) rocket-engine performance-prediction procedure is based on the use of various reference computer programs. One of the reference programs for nozzle analysis is the Two-Dimensional Kinetics (TDK) Program. The purpose of this report is to calibrate the JANNAF procedure that has been incorporated into the December 1984 version of the TDK program for the high-area-ratio rocket-engine regime. The calibration was accomplished by modeling the performance of a 1030:1 rocket nozzle tested at NASA Lewis. A detailed description of the test conditions and TDK input parameters is given. The reuslts indicate that the computer code predicts delivered vacuum specific impulse to within 0.12 to 1.9 percent of the experimental data. Vacuum thrust coefficient predictions were within + or - 1.3 percent of experimental results. Predictions of wall static pressure were within approximately + or - 5 percent of the measured values.

Smith, Tamara A.↗
NASA NTRS1986

Rocket nozzle thermal shock tests in an arc heater facility

A rocket motor nozzle thermal structural test technique that utilizes arc heated nitrogen to simulate a motor burn was developed. The technique was used to test four heavily instrumented full-scale Star 48 rocket motor 2D carbon/carbon segments at conditions simulating the predicted thermal-structural environment. All four nozzles survived the tests without catastrophic or other structural failures. The test technique demonstrated promise as a low cost, controllable alternative to rocket motor firing. The technique includes the capability of rapid termination in the event of failure, allowing post-test analysis.

Painter, James H.↗
NASA NTRS1987

A detailed description of the uncertainty analysis for high area ratio rocket nozzle tests at the NASA Lewis Research Center

A preliminary uncertainty analysis was performed for the High Area Ratio Rocket Nozzle test program which took place at the altitude test capsule of the Rocket Engine Test Facility at the NASA Lewis Research Center. Results from the study establish the uncertainty of measured and calculated parameters required for the calculation of rocket engine specific impulse. A generalized description of the uncertainty methodology used is provided. Specific equations and a detailed description of the analysis is presented. Verification of the uncertainty analysis model was performed by comparison with results from the experimental program's data reduction code. Final results include an uncertainty for specific impulse of 1.30 percent. The largest contributors to this uncertainty were calibration errors from the test capsule pressure and thrust measurement devices.

Davidian, Kenneth J.↗
NASA NTRS1987

Reusable rocket engine optical condition monitoring

Plume emission spectrometry and optical leak detection are described as two new applications of optical techniques to reusable rocket engine condition monitoring. Plume spectrometry has been used with laboratory flames and reusable rocket engines to characterize both the nominal combustion spectra and anomalous spectra of contaminants burning in these plumes. Holographic interferometry has been used to identify leaks and quantify leak rates from reusable rocket engine joints and welds.

Wyett, L.↗
NASA NTRS1988

Liquid rocket boosters for the Space Shuttle - An outline of trade issues and analysis techniques

Numerous liquid rocket booster configurations were studied to replace the Solid Rocket Boosters on the current Space Shuttle. While improved safety, reliability, performance and economy of operation were sought, the designs also sought to minimize volumetric growth to reduce aerodynamic loads and structural modifications. Aero loads could be significant as a function of booster diameter if extrapolated directly from solid rocket characteristics. Procedures to meet these goals with analytical booster sizing and simple dynamic simulations are shown. Engine chamber pressure proved to be a good independent variable for implications of pressure-fed and pump-fed engines, fuel and material selection. For some configurations, ascent trajectory modifications were suggested: longer vertical rise, lofting, heads-up orientation, and higher first and second stage target altitudes. Since engine manufacture would dominate booster costs, booster simplification of reuse are discussed based on cost estimates.

Kelly, W. D.↗
NASA NTRS1988

Rocket- and aircraft-borne trace gas measurements in the winter polar stratosphere

In January and February 1987 stratospheric rocket- and aircraft-borne trace gas measurements were done in the North Polar region using ACIMS (Active Chemical Ionization Mass Spectrometry) and PACIMS (PAssive Chemical Ionization Mass Spectrometry) instruments. The rocket was launched at ESRANGE (European Sounding Rocket Launching Range) (68 N, 21 E, Northern Sweden) and the twin-jet research aircraft operated by the DFVLR (Deutsche Forschungs- und Versuchs-anstalt fuer Luft- und Raumfahrt), and equipped with a mass spectrometer laboratory was stationed at Kiruna airport. Various stratospheric trace gases were measured including nitric acid, sulfuric acid, non-methane hydrocarbons (acetone, hydrogen cyanide, acetonitrile, methanol etc.), and ambient cluster ions. The experimental data is presented and possible implications for polar stratospheric ozone discussed.

Arnold, F.↗
NASA NTRS1989

Fiberoptics for liquid propellant rocket engine environments

Interest is increasing in the use of fiberoptics on liquid-fueled rocket engines in recognition of their immunity to lightning and EMI, light weight, high-frequency response, and the possibility offered by optical technologies to measure additional important engine parameters for which present measurement methods are impractical. This paper discusses the requirements to be placed on fiberoptics applied to liquid-fueled rocket engines; identifies manufacturers of fibers that appear to have promise for the harsh rocket engine applications; and summarizes information on the characteristics of these fibers obtained from the manufacturers, program testing, and the general literature.

Delcher, R.↗
NASA NTRS1989

Development of the Explorer solid rocket motor

The successful launching of Explorer I on an accelerated schedule was due in part to the extensive design and developmental testing effort accomplished in support of the U.S. Army's Sergeant missile system. The 1/5-scale solid rocket motor used in the missile development in conjunction with a modified Redstone rocket became the basis for the Jupiter-C launch vehicle, which launched the first U.S. satellite. A description of the solid rocket motor and its development for use as part of the upper stages of the Jupiter-C is presented.

Sola, F. L.↗
NASA NTRS1990

Array Of Rockets For Multicrewmember Evacuation

Emergency egress system undergoing development for aircraft and aerospace vehicles uses fixed array of tractor rockets to eject crewmembers. Crewmembers hook up to tractor rockets and fire them unaided. Positioned as unit in ready-to-use orientation during flight operations. On ground, swung out of way. Rocket array also mounts under exit hatch, serving as egress ramp.

Allen, Margaret A.↗
NASA NTRS1989

Heat transfer to throat tubes in a square-chambered rocket engine at the NASA Lewis Research Center

A gaseous H2/O2 rocket engine was constructed at the NASA-Lewis to provide a high heat flux source representative of the heat flux to the blades in the high pressure fuel turbopump (HPFTP) during startup of the space shuttle main engines. The high heat flux source was required to evaluate the durability of thermal barrier coatings being investigated for use on these blades. The heat transfer, and specifically, the heat flux to tubes located at the throat of the test rocket engine was evaluated and compared to the heat flux to the blades in the HPFTP during engine startup. Gas temperatures, pressures and heat transfer coefficients in the test rocket engine were measured. Near surface metal temperatures below thin thermal barrier coatings were also measured at various angular orientations around the throat tube to indicate the angular dependence of the heat transfer coefficients. A finite difference model for a throat tube was developed and a thermal analysis was performed using the measured gas temperatures and the derived heat transfer coefficients to predict metal temperatures in the tube. Near surface metal temperatures of an uncoated throat tube were measured at the stagnation point and showed good agreement with temperatures predicted by the thermal model. The maximum heat flux to the throat tube was calculated and compared to that predicted for the leading edge of an HPFTP blade. It is shown that the heat flux to an uncooled throat tube is slightly greater than the heat flux to an HPFTP blade during engine startup.

Nesbitt, James A.↗
NASA NTRS1990

Rocket studies of the lower ionosphere

The earth's ionosphere in the altitude range of 50 to 200 km was investigated by rocket-borne sensors, supplemented by ground-based measurement. The rocket payloads included mass spectrometers, energetic particle detectors, Langmuir probes and radio propagation experiments. Where possible, rocket flights were included in studies of specific phenomena, and the availability of data from other experiments greatly increased the significance of the results. The principal ionospheric phenomena studied were: winter anomaly in radiowave absorption, ozone and molecular oxygen densities, mid-latitude sporadic-E layers, energetic particle precipitation at middle and low latitudes, ionospheric instabilities and turbulence, and solar eclipse effects in the D and E regions. This document lists personnel who worked on the project, and provides a bibliography of resultant publications.

Bowhill, Sidney A.↗
NASA NTRS1989

The liquid rocket booster and its potential for the STS

Results of the liquid rocket booster study initiated by NASA to define an alternative to solid rocket boosters, are presented. The prime study contractors, Martin Marietta Corporation and General Dynamics, have identified liquid rocket booster configurations that can increase shuttle performance to 70 klb. These boosters will provide improved reliability, hold down, verification prior to vehicle release, engine-out and abort capabilities. Phasing of these boosters into Space Transportation System (STS) operations without adversely affecting flight rate is described.

Space Shuttle↗