Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Wind tunnel blockage and support interference effects on winged-body models at Mach numbers from 0.6 to 1.0

Three sting-mounted winged-body models with tunnel blockages of 0.1, 1.0, and 2.0 percent were tested in the Lewis Research Center's 8- by 6- Foot Supersonic Wind Tunnel. Fuselage pressures were obtained over a Mach number range of 0.6 to 1.0 at angles of attack from 0 deg to 4 deg. Two other types of model support were investigated, which included simulated wing-tip and fuselage support-strut mountings. The effects of tunnel porosity and sidewall geometry were also investigated. Model blockage effects were small up to M sub 0 = 0.95. At higher speeds the major blockage effect observed was a displacement of the local transonic terminal shocks on the model. The effects of the wing-tip type of model support were small up to M sub 0 = 0.95, but disturbances were observed on the fuselage at higher speeds. Changes in local tunnel porosity were effective in reducing the disturbances up to M sub 0 = 0.975, but a change in sidewall geometry was not.

Blaha, B. J.↗
NASA NTRS1974

Venting characteristics of gaseous helium and nitrogen discharging into a free stream at Mach numbers from 0.60 to 1.57

An experimental investigation was conducted in the Lewis Research Center 8- by 6-Foot Supersonic Wind Tunnel to compare the effects on discharge coefficient of venting gaseous helium and gaseous nitrogen into a free stream. The test was conducted from Mach 0.06 to 1.57 with the vent mounted in a flat plate. The plate was strut mounted to the tunnel ceiling and at a 0 angle of attack. The gases were discharged from a plenum chamber through a 2.54-centimeter (1.00-in.) diameter vent. The ratio of local static pressure to plenum pressure was varied from 0.51 to 0.975. The ratio of boundary layer thickness to vent diameter varied from a maximum of 1.34 at Mach 0.60 to a minimum of 0.55 at Mach 1.37.

Johns, A. L.↗
NASA NTRS1974

The 727 airplane side inlet low-speed performance confirmation model test for refanned JT8D engines

The results of a low-speed wind tunnel test of a 0.3 scale model 727 airplane side inlet for JT8D-100 engines are presented. The objectives of the test were to develop lines for a full-scale flightworthy inlet, to evaluate inlet total pressure recovery and steady-state total pressure distortion, and to obtain model-scale distortion data which can be used in the assessment of the compatibility of the inlet with the JT8D-100 series engines. A secondary objective was to obtain internal/external cowl static pressures for the determination of nacelle loads. Two basic inlet models were tested at static, forward speed, angle-of-attack (inflow angle), and cross-wind conditions. One model was with and one without an acoustic ring. Two modifications to the models were also tested, one with the ring closer to the inlet throat and one with a larger lip. Test measurements consisted of inlet surface static pressure, engine face total pressure, inlet airflow, tunnel total pressure, tunnel total temperature and tunnel velocity. Total pressure traverses were taken directly behind the ring and strut. No dynamic measurements were taken.

Schuehle, A. L.↗
NASA NTRS1973

Diffraction studies applicable to 60-foot microwave research facilities

The principal features of this document are the analysis of a large dual-reflector antenna system by vector Kirchhoff theory, the evaluation of subreflector aperture-blocking, determination of the diffraction and blockage effects of a subreflector mounting structure, and an estimate of strut-blockage effects. Most of the computations are for a frequency of 15.3 GHz, and were carried out using the IBM 360/91 and 360/95 systems at Goddard Space Flight Center. The FORTRAN 4 computer program used to perform the computations is of a general and modular type so that various system parameters such as frequency, eccentricity, diameter, focal-length, etc. can be varied at will. The parameters of the 60-foot NRL Ku-band installation at Waldorf, Maryland, were entered into the program for purposes of this report. Similar calculations could be performed for the NELC installation at La Posta, California, the NASA Wallops Station facility in Virginia, and other antenna systems, by a simple change in IBM control cards. A comparison is made between secondary radiation patterns of the NRL antenna measured by DOD Satellite and those obtained by analytical/numerical methods at a frequency of 7.3 GHz.

Schmidt, R. F.↗
NASA NTRS1974

An aerodynamic study of scramjet fuel injectors

The aerodynamic drag and fuel distribution patterns of injectors designed for a supersonic combustion ramjet were measured at Mach numbers of 2, 2.5, and 3. The most significant parameter effecting the drag was found to be the injector thickness ratio. A twofold reduction in the thickness ratio caused a 65% decrease in drag. Changing the injector sweep angle by a factor of 2 resulted in only a small change in drag. A reversal of injector sweep, from sweepback to sweepforward, did not change the measured drag. Helium gas was injected through the struts to simulate the penetration and spreading patterns of hydrogen. Sampling measurements were made at approximately two duct heights downstream of the combustor. The spacing required between fuel injectors was found to be about 10 jet diameters. The effect of gas injection on the measured drag was found to be minor.

Povinelli, L. A.↗
NASA NTRS1974

Aerodynamic results of support system interference effects tests conducted in NASA/ARC 6 by 6-foot supersonic wind tunnel using an 0.015-scale model of the configuration 14OA/B SSV orbiter (OA59), volume 1

An experimental aerodynamic investigation was conducted in the NASA/ARC 6- by 6-foot supersonic wind tunnel on an 0.015-scale configuration 140A/B SSV Orbiter model. The primary objective was to determine the extent aerodynamic simulation is compromised by sting base mounting with MPS nozzles removed. Both a conventional sting (through the base) and an alternate model mounting system were utilized. The alternate mounting system consisted of a non-metric blade strut, which approximated the vertical tail and entered the model through the upper aft section of its fuselage. The model was tested both in and out of the presence of a dummy sting with and without MPS nozzles when on the alternate mounting system. Data were obtained at Mach numbers from 0.6 through 2.0, a Reynolds number of 2.5 million per foot, angles of attack from -4 through 14 degrees, angles of sideslip from -15 through 15 degrees, elevon deflections of 0 and 15 degrees, and bodyflap deflections of -11.7, 0, and 16.3 degrees.

Campbell, J. H., II↗
NASA NTRS1974

Effect of interjet spacing on mixing of multiple coaxial jets in supersonic flow

An experimental and analytical investigation of strut-mounted, four-nozzle, downstream facing, gaseous fuel injector assembly was conducted in a Mach 4 air-stream with P = 154 psia and T sub o 520 R. Helium was used as the injectant, and the interjet spacing (S/D) was the main parameter varied. The principal data are in the form of Helium concentration profiles at seven axial stations, Mach number distributions at three axial stations and schlieren photographs of the flow field at different interjet spacings. An approximate analysis was developed based upon a linearization in the Von Mises plane, Crocco integrals for the temperature and concentrations fields and an eddy viscosity model. Good agreement with the data was achieved. It was found that, at these conditions, interjet spacing has an effect on mixing only up to S/D of approximately 2.5, with concentration of injectant becoming smaller as S/D is increased, and the Mach number downstream of the injector tends to decrease with decreasing S/D.

Lorber, A. K.↗
NASA NTRS1974

Subsonic and transonic hinge moment and wing bending/torsion characteristics of .015 scale space shuttle models 49-0 and 67-TS in the Rockwell International trisonic wind tunnel (IA70), volume 1

Experimental aerodynamic investigations were conducted on an 0.015-scale representation of the integrated space shuttle launch vehicle in the trisonic wind tunnel. The primary test objective was to obtain subsonic and transonic elevon and bodyflap hinge moments and wing bending-torsion moments in the presence of the launch vehicle. Wing pressures were also recorded for the upper and lower right wing surfaces at two spanwise stations. The hinge moment, wing bending/torsion moments and wing pressure data were recorded over an angle-of-attack (alpha) range from -8 deg to +8 deg, and angle-of-sideslip (beta) range from -8 deg to +8 deg and at Mach numbers of 0.90, 1.12, 1.24 and 1.50. Tests were also conducted to determine the effects of the orbiter rear attach cross beam and the forward attach wedge and strut diameter. The orbiter alone was tested at 0.90 and 1.24 Mach number only.

Hughes, M. T.↗
NASA NTRS1975

Experimental investigation of a simple distortion index utilizing steady-state and dynamic distortions in a Mach 2.5 mixed-compression inlet and turbofan engine

A wind tunnel investigation was conducted to determine the amplitude and spatial distribution of steady-state and dynamic distortion produced in an inlet with 45 percent of the overall supersonic area contraction occurring internally. It was found that the inlet support strut location and/or the overboard bypass flow rate has a significant effect on the spatial distribution of distortion. Because of this effect the majority of the stall points exhibited four-per-revolution patterns of distortion. Data from this test were used to formulate a simple index that combines steady-state and dynamic distortions. Distortion results obtained with this index correlated well with exhaust nozzle area. It is shown that the exhaust nozzle area of a TF30-P-3, as modified for use in this test, can be controlled in a scheme to avoid engine stall. A considerable increase in engine distortion tolerance can be achieved by opening the 7th-stage bleed. The engine exhibited higher tolerance to distortion for multiple patterns of distortion per-revolution than for a one-per-revolution pattern of distortion.

Costakis, W. G.↗
NASA NTRS1975

Internally supported flexible duct joint

An internally supported, flexible duct joint for use in conducting fluids under relatively high pressures in systems where relatively large deflection angles must be accommodated is presented. The joint includes a flexible tubular bellows and an elongated base disposed within the bellows. The base is connected through radiating struts to the bellows near mid-portion and to each of the opposite end portions of the bellows through a pivotal connecting body. A motion-controlling linkage is provided for linking the connecting bodies, whereby angular displacement of the joint is controlled and uniformity in the instantaneous bend radius of the duct is achieved as deflection is imposed.

Kuhn, R. F., Jr.↗
NASA NTRS1975

Shake test of rotor test apparatus in the 40- by 80-foot wind tunnel

A shake test was conducted to determine the dynamic characteristics of a rotor test apparatus on strut systems. The rotor-off hub transfer function (acceleration per unit force as a function of frequency) was measured in the longitudinal and lateral directions, using a combination of broadband and discrete frequency excitation techniques. The dynamic data is summarized for the configurations tested, giving the following properties for each mode identified: the natural frequency, the hub response at resonance, and the fixed system damping. The complete transfer functions are presented, and the detailed test results are included as an appendix. Data analysis techniques developed to obtain on-line measurements of the system modal properties, including the damping coefficient and the damping ratio are discussed.

Johnson, W.↗
NASA NTRS1975

Hypersonic research engine project. Phase 2: Some combustor test results of NASA aerothermodynamic integration model

Combustor test results of the NASA Aerothermodynamic Integration Model are presented of a ramjet engine developed for operation between Mach 3 and 8. Ground-based and flight experiments which provide the data required to advance the technology of hypersonic air-breathing propulsion systems as well as to evaluate facility and testing techniques are described. The engine was tested with synthetic air at Mach 5, 6, and 7. The hydrogen fuel was heated to 1500 R prior to injection to simulate a regeneratively cooled system. Combustor efficiencies up to 95 percent at Mach 6 were achieved. Combustor process in terms of effectiveness, pressure integral factor, total pressure recovery and Crocco's pressure-area relationship are presented and discussed. Interactions between inlet-combustor, combustor stages, combustor-nozzle, and the effects of altitude, combustor step, and struts are observed and analyzed.

Sun, Y. H.↗
NASA NTRS1975

Hole cutter

An adjustable hole cutter is described for use in forming circular openings in workpieces. The hole cutter is characterized by a mount of a substantially planar configuration, positionable into a plane paralleling the working plane of a selected workpiece. It also contains a shaft for imparting rotary motion to the mount about an axis of rotation normally related to the working plane, a plurality of stabilizing struts for resiliently supporting the mount in parallelism with the working plane as rotary motion is imparted thereto, a drill bit for drilling a pilot hole concentric with the axis of rotation, and an elongated cutting tool adjustably seated within a radially extended slot.

Thornton, G. E.↗
NASA NTRS1975

Results of a space shuttle vehicle ferry configuration afterbody fairing optimization study using a 140A/B 0.0405-scale model orbiter (43-0) in the Rockwell International 7.75 by 11.0 ft low speed wind tunnel (OA124)

Experimental aerodynamic investigations were conducted on a dual-strut mounted 0.0405-scale representation of the 140A/B outer mold line space shuttle orbiter vehicle. The tests, conducted from 11 Oct., 1974 through 22 Oct., 1974, were primarily to investigate aerodynamic stability and control characteristics of the space shuttle orbiter ferry configuration. Four afterbody fairing configurations and various additions to them in the form of horizontal and ventral fins strakes and other aerodynamic protuberances were tested. Base line data on the basic orbiter with MPS nozzles and bodyflap were recorded. The drag of the optimum ferry configuration was increased to the level of the basic orbiter for possible flight test configurations by the addition of two sizes of perforated speed brakes on the tail cone surface.

Houlihan, S. R.↗
NASA NTRS1975

Metal temperatures and coolant flow in a wire cloth transpiration cooled turbine vane

An experimental heat transfer investigation was conducted on an air-cooled turbine vane made from wire-wound cloth material and supported by a central strut. Vane temperature data obtained are compared with temperature data from two full-coverage film-cooled vanes made of different laminated construction. Measured porous-airfoil temperatures are compared with predicted temperatures.

Gladden, H. J.↗
NASA NTRS1975

Reentry static stability characteristics of a (Model 471) .005479-scale 146-inch solid rocket booster tested in the NASA/MSFC 14 by 14 inch TWT (SA8F)

A force test of a scale model of the Space Shuttle Solid Rocket Booster was conducted in a trisonic wind tunnel. The model was tested with such protuberances as a camera capsule, electrical tunnel, attach rings, aft separation rockets, ET attachment structure, and hold-down struts. The model was also tested with the nozzle at gimbal angles of 0, 2.5, and 5 degrees. The influence of a unique heat shield configuration was also determined. Some photographs of model installations in the tunnel were taken and are included. Schlieren photography was utilized for several angles of attack.

Johnson, J. D.↗
NASA NTRS1975

Design and performance at a local Mach number of 6 of an inlet for an integrated Scramjet concept

The development of a concept for a modular supersonic combustion ramjet which is designed to integrate with the airframe of a hypersonic vehicle is presented. The design philosophy and results of experiments at Mach 6 to evaluate the performance of the scramjet inlet are given. The inlet was designed with modest contraction ratio, fixed geometry, and three fuel injection struts which contributed to the inlet flow compression and provided a short combustor design that resulted in low internal cooling requirements. Results indicate that the inlet performance is well within the acceptable range for high engine performance.

Trexler, C. A.↗
NASA NTRS1975

Shake test of rotor test apparatus with balance dampers in the 40 by 80 foot wind tunnel

A shake test was conducted to determine the dynamic characteristics of a rotor test apparatus on two strut systems with balance dampers in the Ames 40- by 80-ft wind tunnel. The rotor-off hub transfer function (acceleration per unit force as a function of frequency) was measured in the longitudinal and lateral directions, using a combination of broadband and discrete frequency excitation techniques. The dynamic data are summarized for the configurations tested, giving the following properties for each mode identified: the natural frequency, the hub response at resonance, the fixed system damping, the damping ratio, and the modal mass. The complete transfer functions are presented, and the detailed test results are included as an appendix.

Johnson, W.↗