SEARCH · Search NASA

Results for “TEST EQUIPMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1980

A radiant heating test facility for space shuttle orbiter thermal protection system certification

A large scale radiant heating test facility was constructed so that thermal certification tests can be performed on the new generation of thermal protection systems developed for the space shuttle orbiter. This facility simulates surface thermal gradients, onorbit cold-soak temperatures down to 200 K, entry heating temperatures to 1710 K in an oxidizing environment, and the dynamic entry pressure environment. The capabilities of the facility and the development of new test equipment are presented.

Sherborne, W. D.↗

NASA NTRS1981

Fatigue degradation in compressively loaded composite laminates

The effect of imbedded delaminations on the compression fatigue behavior of quasi-isotropic, T300/5208, graphite/epoxy laminates was investigated. Teflon imbedments were introduced during panel layup to create delaminations. Static and constant amplitude (R=10, omega = 10 Hz) fatigue tests were conducted. S-N data and half life residual strength data were obtained. During static compression loading, the maximum deflection of the buckled delaminated region was recorded. Under compression fatigue, growth of the imbedded delamination was identified as the predominant failure mode in most of the test cases. Specimens that exhibited others failures had a single low stiffness ply above the Teflon imbedment. Delamination growth during fatigue was monitored using DIB enhanced radiography. In specimens with buried delaminations, the dye penetrant (DIB) was introduced into the delaminated region through a minute laser drilled hole, using a hypodermic needle. A low kV, microfocus, X-ray unit was mounted near the test equipment to efficiently record the cyclic growth of buried delaminations on Polaroid film.

Ramkumar, R. L.↗

NASA NTRS1981

The Space Shuttle - Orbital flight phase begins

The results of the first orbital flight test of the Space Shuttle are summarized and the future operations are discussed. It is mentioned that increased payload lift capability will be obtained through a series of planned steps which have already been initiated in the program. These include the use of the main engines at higher thrust levels, lower weight External Tank and Solid Rocket Boosters (SRB's), higher thrust SRB's, and removal of certain test equipment from the Orbiter. The economics of the Space Shuttle to the users and the future uses of the Space Shuttle are also discussed.

Day, L. E.↗

NASA NTRS1983

Microprogramed Sequencer for Tunable RF Oscillator

Standard IC chips and digitally tuned oscillator combined. Circuit consists of PROM-based microprogramed control sequencer, which drives group of diode switches to select one of eight tuning capacitors in L-C oscillator. Circuit originally designed to "dither" transmitter frequency of K-band radar at high rates finds application in other areas, as automated test equipment or computer-controlled receiver tuning.

Couch, R. H.↗

NASA NTRS1983

Inexpensive Bolt-Load Gage

"Built-in" gage determines whether large bolt or stud has been torqued to desired load and provides for continuous inspection to ensure proper load is being maintained. Gage detects longitudinal stress/strain bolt; requires no electronic or sonic test equipment.

Long, M. J.↗

NASA NTRS1981

Automated Power Systems Management (APSM)

A breadboard power system incorporating autonomous functions of monitoring, fault detection and recovery, command and control was developed, tested and evaluated to demonstrate technology feasibility. Autonomous functions including switching of redundant power processing elements, individual load fault removal, and battery charge/discharge control were implemented by means of a distributed microcomputer system within the power subsystem. Three local microcomputers provide the monitoring, control and command function interfaces between the central power subsystem microcomputer and the power sources, power processing and power distribution elements. The central microcomputer is the interface between the local microcomputers and the spacecraft central computer or ground test equipment.

Bridgeforth, A. O.↗

NASA NTRS1982

Digital processing clock

Tthe digital processing clock SG 1157/U is described. It is compatible with the PTTI world where it can be driven by an external cesium source. Built-in test equipment shows synchronization with cesium through 1 pulse per second. It is built to be expandable to accommodate future time-keeping needs of the Navy as well as any other time ordered functions. Examples of this expandibility are the inclusion of an unmodulated XR3 time code and the 2137 modulate time code (XR3 with 1 kHz carrier).

Phillips, D. H.↗

NASA NTRS1982

An advanced tracker design for pointing and control of space vehicles using the charge injection device

The use of charge transfer devices (CTD) in pointing and control of space vehicles is examined, with emphasis on the use of charge injection devices (CID). The selection of CTD type and CID operation, including CID signal and noise analysis and signal improvement, are discussed. Star tracking operational advantages of the CTD are pointed out, and the tracking optical concept is discussed and graphically depicted. The position interpolation procedure and the effects of rate of stellar motion on position interpolation are considered, and error analysis is examined. Finally, the breadboard and test program are discussed in detail, coarse and fine acquisition, test for star, track pattern, test procedure and results. An overall accuracy performance of approximately 0.02 pixels or approximately 0.8 arcsec for the test equipment and tracker was obtained.

Jones, C.↗

NASA NTRS1982

Rotating gravity gradiometer study

Two rotating gravity gradiometer (RGG) sensors, along with all the external electronics needed to operate them, and the fixtures and special test equipment needed to fill and align the bearings, were assembled in a laboratory, and inspected. The thermal noise threshold of the RGG can be lowered by replacing a damping resistor in the first stage electronics by an active artificial resistor that generates less random voltage noise per unit bandwidth than the Johnson noise from the resistor it replaces. The artificial resistor circuit consists of an operational amplifier, three resistors, and a small DC to DC floating power supply. These are small enough to be retrofitted to the present circuit boards inside the RGG rotor in place of the 3 Megohm resistor. Using the artificial resistor, the thermal noise of the RGG-2 sensor can be lowered from 0.3 Eotvos to 0.15 Eotvos for a 10 sec integration time.

Forward, R. L.↗

NASA NTRS1981

Experimental program for the evaluation of turbofan/turboshaft c conversion technology

A TF34 turbofan engine is being modified to produce shaft power from an output coupling on the fan disk when variable inlet guide vanes are closed to reduce fan airflow. The engine, called a convertible engine, could be used on advanced rotorcraft such as X-wing, ABC (Advanced Blade Concept), and Folding Tilt Rotor, and on V/STOL craft in which two engines are cross-coupled. The engine will be tested on an outdoor static test stand at NASA Lewis Research Center. Steady-state tests will be made to measure performance in turbofan, turboshaft, and combined power output modes. Transient tests will be made to determine the response to the engine and a new digital engine control system for several types of rapid changes in thrust and shaft loads. The paper describes the engine modifications, the test facility equipment, proposed testing techniques for several types of tests, and typical test results predicted from engine performance computer programs.

Mcardle, J. G.↗

NASA NTRS1983

Initial '80s Development of Inflated Antennas

State of the art technology was considered in the definition and documentation of a membrane surface suitable for use in a space reflector system for long durations in orbit. Requirements for a metal foil-plastic laminate structural element were determined and a laboratory model of a rigidized element to test for strength characteristics was constructed. Characteristics of antennas ranging from 10 meters to 1000 meters were determined. The basic antenna configuration studied consists of (1) a thin film reflector, (2) a thin film cone, (3) a self-rigidizing structural torus at the interface of the cone and reflector; and (4) an inflation system. The reflector is metallized and, when inflated, has a parabolic shape. The cone not only completes the enclosure of the inflatant, but also holds the antenna feed at its apex. The torus keeps the inflated cone-reflector from collapsing inward. Laser test equipment determined the accuracy of the inflated paraboloids.

Friese, G. J.↗

NASA NTRS1983

Pilot response with conventional displays

A critical examination of pilot-aircraft-display system response was conducted for conventional displays. The system frequency and damping both by visual examination of system responses to initial errors and by pilot model analysis was studied. Examples of system response at two points in a flight are shown. The long periods and the occasional loss of system damping in these responses are a matter of concern. These system characteristics can be duplicated with the pilot model given on the pilot-model-aircraft system block diagram. The responses obtained with the pilot model are also shown, together with the pilot model gains used in obtaining these responses. The factors that determine what these gains will be are the requirements for system stability, the sensitivity of the displays, and the scanning required in looking at the displays. The effects of scanning on system response can be determined with the test set-up given. Using this test equipment, it was found that separating bank angle information from heading information caused a noticeable degradation in system response.

Adams, J. J.↗

NASA NTRS1985

Vapor-screen technique for flow visualization in the Langley Unitary Plan Wind Tunnel

The vapor-screen technique for flow visualization, as developed for the Langley Unitary Plan Wind Tunnel, is described with evaluations of light sources and photographic equipment. Test parameters including dew point, pressure, and temperature were varied to determine optimum conditions for obtaining high-quality vapor-screen photographs. The investigation was conducted in the supersonic speed range for Mach numbers from 1.47 to 4.63 at model angles of attack up to 35 deg. Vapor-screen photographs illustrating various flow patterns are presented for several missile and aircraft configurations. Examples of vapor-screen results that have contributed to the understanding of complex flow fields and provided a basis for the development of theoretical codes are presented with reference to other research.

Morris, O. A.↗

NASA NTRS1985

Circulation control lift generation experiment: Hardware development

A circulation control airfoil and its accompanying hardware were developed to allow the investigation of lift generation that is independent of airfoil angle of attack and relative flow velocity. The test equipment, designed for use in a water tunnel, includes the blown airfoil, the support systems for both flow visualization and airfoil load measurement, and the fluid control system, which utilizes hydraulic technology. The primary design tasks, the selected solutions, and the unforseen problems involved in the development of these individual components of hardware are described.

Panontin, T. L.↗

NASA NTRS1986

Three-Axis Load-Cell Assembly

Force-measuring device both sensitive and rugged. Load-cell assembly placed between manipulator and object being manipulated. Load cells measure forces on object almost directly, without interference by intervening manipulator forces. Developed for use with remote manipulator that bends cryogenic ducts. Device rugged and functions over wide range, having applications in automatic testing equipment, industrial robots, and force-measuring equipment.

Rewerts, G. R.↗

NASA NTRS1986

Low-Flammability PTFE for High-Oxygen Environments

Modified forming process removes volatile combustible materials. Flammability of cable-wrapping tape reduced by altering tape-manufacturing process. In new manufacturing process, tape formed by proprietary process of screw extrusion, followed by washing in solvent and drying. Tape then wrapped as before. Spectrogram taken after extrusion, washing, and drying shows lower hydrocarbon content. PTFE formed by new process suited to oxygen-rich environments. Safe in liquid oxygen of Space Shuttle tank and in medical uses; thin-wall shrinkable tubing in hospital test equipment, surgical instruments, and implants.

Walle, E.↗

NASA NTRS1984

Characterization of an advanced focal plane for multispectral linear array (MLA) application

It is pointed out that the MLA instrument represents the next generation in the Landsat series of earth resources satellites. The MLA sensor concept utilizes a pushbroom scan mode to eliminate electromechanical scan mirrors, and the lower reliabililty and higher power dissipation which accompany their employment. The pushbroom scanner makes use of a linear array which consists generally of thousands of detectors oriented perpendicular to the along-track direction of the satellite. Test techniques have been developed for the measurement of the module parameters which are critical to MLA focal plane performance. These measurements include the determination of infrared responsivity, linearity over the dynamic range, temporal noise, and fixed pattern effects on each detector element of each module tested. Tests related to spectral response, crosstalk, and spot scan profiles are also conducted. A description is provided of the test equipment involved.

King, P.↗

NASA NTRS1985

Guide to using lunar soil and simulants for experimentation

It is pointed out that lunar soil can be described as well-graded silty sands or sandy silts with an average particle size by weight in the range from 0.040 to 0.130 mm. The density of in situ bulk lunar soil is typically 1.4 to 1.9 g/cu cm. Changes in soil from moon to laboratory are considered along with some critical differences between simulants and lunar soil. Attention is given to agglutinates, iron metal distributed throughout the agglutinatic glass, solar wind hydrogen, and major lunar minerals (anorthite, pyroxene, ilmenite, olivine). The use of lunar fines as experimental samples is discussed, and the characteristics of simulants for experiments are examined, taking into account grain size distribution, particle type distribution, a highlands simulant, and a high titanium mare simulant. Simulants for testing equipment and structures are also described.

Allton, J. H.↗