Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile Strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The effect of aspect ratio on the mechanical behavior of Li metal in solid-state cells

The Li metal anode is necessary for solid-state batteries to dramatically exceed the energy density of state-of-the-art conventional Li-ion batteries. To enable the Li metal anode, the mechanical properties of Li metal under compression in a commercially relevant cell configuration must be determined. This work examines the compression creep behavior of Li metal coupled with a relevant model solid-state electrolyte (Li 6.5 La 3 Ta 0.5 Zr 1.5 O 12 ) and current collector (Ni) as a function of applied stress (1–10 MPa) and Li foil thickness (100–700 μm). At 1 MPa applied stress, the strain rate of all Li foil thicknesses under compression was almost four orders of magnitude lower than what is predicted from tensile creep tests. Steady-state creep behavior was observed for Li foil ≥350 μm at 5 MPa and ≥250 μm at 10 MPa. Conversely, sustained creep deformation was not observed for 100 and 150 μm Li foils at any applied stress. It is suggested that friction at the Li/LLZO and Li/Ni interfaces leads to the formation of hydrostatic stress that controls Li deformation at low aspect ratios. Finally, these results have implications for battery pack stack pressure requirements, particularly relating to void formation during stripping and Li metal filament penetration during plating.

25 ENERGY STORAGE↗
DOE OSTI2022

Coupled diffusion-deformation-damage model for polymers used in hydrogen infrastructure

The soft materials used in the infrastructure of hydrogen storage and distribution systems are vulnerable because exposure to high-pressure hydrogen can lead to mechanical damage and property degradation. Some materials, such as polymers, can undergo mechanical failure due to a phenomenon wherein hydrogen gas diffuses through the polymer chains and occupies preexisting cavities or voids inside the polymer material. If the hydrogen gas pressure is reduced more quickly than hydrogen can diffuse back out of the polymer which is necessary for some applications, the trapped hydrogen gas instead escapes by rupturing the material, causing surface blistering or permanent damage. In this study, a continuum mechanics-based fully coupled diffusion-deformation model with damage is developed to predict the stress distribution and damage propagation while the polymer undergoes rapid decompression failure. The hyperelastic material model, along with the maximum principal strain failure theory, was chosen for this study as it represents the nonlinear material response with brittle failure observed in uniaxial tensile tests perfectly. EPDM polymer was chosen for this study because of its commercial availability and common use in hydrogen storage and distribution system. It has superior mechanical properties, high and low temperature resistance, and certain compounds work well in hydrogen gas. This work is useful for design engineers to alter the parameters while manufacturing polymer composites to increase their performance in a high-pressure hydrogen environment.

Kulkarni, Shank S.↗
DOE OSTI2025

Forming Limits of Thin Ferritic Stainless Steel for Fuel Cell Application

To lower the cost of fuel cell bipolar plate (BPP), less expensive ferritic stainless steel (FSS) BPP substrate materials are investigated. A series of tensile tests and multistage microchannel-forming tests were conducted on 85-µm-thick ferritic stainless steel foils, 439L, 444, and Chromeshield® 22, to understand the effect of the forming temperatures, tooling geometry, and processes on their formability. Three microchannel-forming processes were conducted, which are 1-Hit (single-stage forming), 2-Hit (two-stage forming) with 50% preform, and 2-Hit with 80% preform. FLC o s at various microchannel-forming conditions were obtained to address the formability of the ferritic stainless steel foils under plane strain conditions. It has been found that the larger the microchannel radius, the better the formability, two-stage forming is superior to the single-stage process, and a larger draw percentage in preform (stage I) leads to a higher FLC o or better formability. It has also been found from tensile tests that the thermal effect (higher temperature) has a negative impact on the failure strains. A similar phenomenon was also observed through channel-forming tests conducted at room temperature, 100 °C, and 200 °C.

08 HYDROGEN↗
DOE OSTI2023

Implementation and experimental validation of nonlocal damage in a large-strain elasto-viscoplastic FFT-based framework for predicting ductile fracture in 3D polycrystalline materials

Ductile materials, such as metal alloys, can undergo substantial deformation before failure. Additionally, these materials are usually of polycrystalline composition and exhibit strongly anisotropic behavior at small length scales. Previously developed fast Fourier transform (FFT)-based models can model ductile fracture of isotropic materials or the elastic–plastic behavior of anisotropic polycrystalline materials; however, there remains a need to couple both capabilities. This work extends a large-strain FFT-based crystal plasticity model to simulate ductile fracture of polycrystalline materials. In this work, a triaxiality-based continuum damage mechanics (CDM) formulation is incorporated into a large-strain elasto-viscoplastic FFT (LS-EVPFFT) framework. The CDM formulation is augmented with an integral-based nonlocal regularization approach that correctly handles gas-phase material necessary to model unconstrained surfaces. To validate the damage-enabled LS-EVPFFT framework, mesoscale copper tensile coupons were machined using microwire electrical discharge machining and experimentally characterized using electron backscatter diffraction. In-situ optical digital image correlation was performed during uniaxial testing to provide a side-by-side comparison of the experimental and computational strain fields and stress–strain responses. The damage-enabled LS-EVPFFT framework can simulate the complete macroscopic stress–strain response of ductile polycrystals to failure. The model reproduces necking behavior that qualitatively agrees with experimental observations. By leveraging the relatively low computational cost of the damage-enabled LS-EVPFFT framework, the framework presented here allows the ductile fracture response of 3D polycrystalline materials to be tractably predicted.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Report on RIA Relevant Modified Burst Testing of ATF Cladding Materials

The mechanical performance of accident-tolerant fuel (ATF) cladding candidates in light-water reactors (LWRs) must be similar to or better than that of current conventional nuclear fuel claddings to reduce dose to the public and ensure a that the core coolable geometry is maintained during a postulated reactivity-initiated accident (RIA) in light-water reactors (LWRs). During an RIA event, the rapid thermal expansion of nuclear fuel can deform the cladding once the fuel–cladding gap closes. In some cases, the pellet–cladding mechanical interaction (PCMI) can induce mechanical failure in ATF candidates. Thus, the mechanical response of ATF cladding must be investigated by mimicking the conditions of RIA and potentially performing Transient Reactor Test (TREAT) experiments to establish or verify the safety envelope. The work presented in this report investigated the failure behavior of as-received, hydrided, and chromium-coated (Cr-coated) Zircaloy-4 (Zry-4) cladding tube under strain-driven mechanical conditions, mimicking postulated RIA loading conditions. Mechanical testing was performed at 300°C via modified burst test (MBT) equipment with pulse width control previously developed under the Department of Energy’s (DOE’s) Advanced Fuel Campaign (AFC). The mechanical strains were determined using 2D digital image correlation (DIC) techniques. The base Zry-4 acquired by Cameco Inc. was in stress-relieved annealed (SRA) condition. Because of the observed large deformation of the cladding tubes, the failure strain definition was updated for the MBT, which can also be applied to other tube tests where significant bulging (out-of-plane deformation) is present. The failure strain was determined to be affected by the speed of the test or the RIA event. As the RIA-like event duration decreased from 75 to 15 ms, the failure strain decreased 5, 7 and 1% for as-received, hydrided, and Cr-coated specimens, respectively. Fractography on the Cr-coated specimens indicated the presence of two failure mechanisms: (i) crenulation at the outer surface of the coating due to the tensile tractional forces along with coatings grain microstructure and (ii) formation of critical defect at the coating/cladding interface that initiated coating rupture after severe plastic deformation of the Zry- 4 substrate. Based on the MBT results and fractography observations, performing mechanical property testing at high strain rates—in particular on Cr-coated tubes—and semi-integral TREAT experiments are required future efforts to ensure ATF cladding performance during transients. The testing recommended would also inform the development of long-term generalized cladding technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Experimental investigation on the effects of fabric architectures on mechanical and damage behaviors of carbon/epoxy woven composites

The mechanical behaviors and damage evolutions of carbon/epoxy woven fabric composites with three different geometries, i.e., one plain weave and two twill weave patterns with different areal densities, are studied under tensile loading. The effects of weave patterns on mechanical properties are investigated by monotonic and cyclic tension tests. Remarkable variations in stress–strain curve, Poisson’s ratio, residual strain and strain map exist in the three composites. Crimp ratio is found to be a critical factor to govern the mechanical properties. With smaller crimp ratio, a quasi-linear stress–strain curve with higher elastic modulus and strength is observed. The stress–strain curves of composites with higher crimp ratio contain transition stages with significant tangent modulus degradation. Elastic modulus, strength and damage initiation are all correlated with the crimp ratio linearly regardless of the fabric pattern. Dramatic nonlinear evolution in Poisson’s ratio occurs in the composite with higher crimp ratio. Cyclic tension results indicate that the residual strain is a more appropriate damage indicator than the unloading elastic modulus. Microstructure examination shows that damage developments are essentially related to the fabric geometry, and result in various mechanical behaviors. This work provides important insights into the geometry-deformation mechanism-mechanical property relationship of the woven composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hierarchical crack buffering triples ductility in eutectic herringbone high-entropy alloys

In human-made malleable materials, microdamage such as cracking usually limits material lifetime. Some biological composites, such as bone, have hierarchical microstructures that tolerate cracks but cannot withstand high elongation. Here, we demonstrate a directionally solidified eutectic high-entropy alloy (EHEA) that successfully reconciles crack tolerance and high elongation. The solidified alloy has a hierarchically organized herringbone structure that enables bionic-inspired hierarchical crack buffering. This effect guides stable, persistent crystallographic nucleation and growth of multiple microcracks in abundant poor-deformability microstructures. Hierarchical buffering by adjacent dynamic strain–hardened features helps the cracks to avoid catastrophic growth and percolation. Our self-buffering herringbone material yields an ultrahigh uniform tensile elongation (~50%), three times that of conventional nonbuffering EHEAs, without sacrificing strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Heterogeneous solute segregation suppresses strain localization in nanocrystalline Ag-Ni alloys

Solute segregation to individual grain boundaries is used by design to produce strong and stable nanocrystalline metallic alloys. Grain-boundary segregation, however, is known to cause adverse embrittlement effects from a strain-localization failure mechanism that imposes significant material limitations for structural applications. Here, using atomistic simulations, it is discovered that heterogeneous Ni segregation in nanocrystalline Ni-mixed Ag alloys dramatically shuts down localized shear bands during plastic deformation, while simultaneously increasing the tensile strength. Nanocrystalline Cu-mixed Ag metals are predicted to exhibit standard homogeneous Cu segregation and a tensile strength that saturates above a solute concentration of 8 at.% due to glass-like shear localization induced by grain boundaries. By contrast, it is found that heterogeneous Ni segregation in nanocrystalline Ag-Ni alloys forms solute-rich clusters along interfaces leading to strain delocalization at high strain and continuous strengthening at high solute concentrations up to 15 at.%. As a result, this study reveals the importance of heterogeneous versus homogeneous segregation behaviors on strain localization and points to a fundamentally new strategy to design failure-resistant nanostructured materials through grain boundary segregation engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Stress and Strain Heterogeneity and Persistence in Uniaxially‐ and Triaxially‐Loaded Sandstone

Two critical questions in brittle rock mechanics are how rocks developed localized strains and to what extent internal stress heterogeneity controls this localization and subsequent macroscopic failure. Definitive answers have not yet been found, but would provide insight into rock fracture mechanics as relevant to hydrocarbon extraction and sequestration. Here, we use synchrotron X‐ray tomography (XRT) and 3D X‐ray diffraction (3DXRD) during uniaxial and triaxial tests on Nugget and Bentheimer sandstones to examine strain and stress localization prior to mechanical failure. 3DXRD was used to measure intra‐granular lattice strains which were used to compute elastic stress tensors of each grain. Digital volume correlation (DVC) was applied to XRT images to determine the strain field in the sample. Both samples featured marked spatial heterogeneity, localization, and temporal persistence of elevated stresses and strains during their mechanical deformation toward failure. Both samples featured a majority of grains with at least one principal stress component that was tensile, a signature of the influence of heterogeneity on stress transmission. Measurements further revealed that compressive stress orientations and statistics evolved in a similar manner to those of inter‐particle forces in loose granular materials, with triaxially‐compressed rock exhibiting enhanced grain stress heterogeneity compared to uniaxially‐compressed rock. Our results complement recent work by others who employed XRT and scanning 3DXRD to study triaxially‐compressed sandstone, but extend those results to uniaxial compression, sandstones of varied porosity, and grain stress measurements throughout the 3D full extent of the samples rather than in a single layer examined with scanning 3DXRD.

58 GEOSCIENCES↗
DOE OSTI2023

Tailoring planar slip to achieve pure metal-like ductility in body-centred-cubic multi-principal element alloys

Uniform tensile ductility (UTD) is crucial for the forming/machining capabilities of structural materials. Normally, planar-slip induced narrow deformation bands localize the plastic strains and hence hamper UTD, particularly in body-centred-cubic (bcc) multi-principal element high-entropy alloys (HEAs), which generally exhibit early necking (UTD < 5%). Here we demonstrate a strategy to tailor the planar-slip bands in a Ti-Zr-V-Nb-Al bcc HEA, achieving a 25% UTD together with nearly 50% elongation-to-failure (approaching a ductile elemental metal), while offering gigapascal yield strength. The HEA composition is designed not only to enhance the B2-like local chemical order (LCO), seeding sites to disperse planar slip, but also to generate excess lattice distortion upon deformation-induced LCO destruction, which promotes elastic strains and dislocation debris to cause dynamic hardening. Further, this encourages second-generation planar-slip bands to branch out from first-generation bands, effectively spreading the plastic flow to permeate the sample volume. Moreover, the profuse bands frequently intersect to sustain adequate work-hardening rate (WHR) to large strains. Our strategy showcases the tuning of plastic flow dynamics that turns an otherwise-undesirable deformation mode to our advantage, enabling an unusual synergy of yield strength and UTD for bcc HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Molecular Origin of Strain-Induced Chain Alignment in PDPP-Based Semiconducting Polymeric Thin Films

Donor–acceptor (D–A) type semiconducting polymers have shown great potential for the application of deformable and stretchable electronics in recent decades. However, due to their heterogeneous structure with rigid backbones and long solubilizing side chains, the fundamental understanding of their molecular picture upon mechanical deformation still lacks investigation. Here, the molecular orientation of diketopyrrolopyrrole (DPP)-based D–A polymer thin films is probed under tensile deformation via both experimental measurements and molecular modeling. The detailed morphological analysis demonstrates highly aligned polymer crystallites upon deformation, while the degree of backbone alignment is limited within the crystalline domain. Besides, the aromatic ring on polymer backbones rotates parallel to the strain direction despite the relatively low overall chain anisotropy. Additionally, the effect of side-chain length on the DPP chain alignment is observed to be less noticeable. These observations are distinct from traditional linear-chain semicrystalline polymers like polyethylene due to distinct characteristics of backbone/side-chain combination and the crystallographic characteristics in DPP polymers. Furthermore, a stable and isotropic charge carrier mobility is obtained from fabricated organic field-effect transistors. This study deconvolutes the alignment of different components within the thin-film microstructure and highlights that crystallite rotation and chain slippage are the primary deformation mechanisms for semiconducting polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A continuum damage approach to spallation and the role of microinertia

Spall failure is of interest due to its prevalence in high strain rate problems in which the spallation is driven by the interaction of release waves. In this article, a porosity-based damage model that includes microinertial effects is used to examine spall failure. The model is successfully calibrated to plate impact-driven experiments and then used to evaluate experimental conditions producing more extreme strain rate conditions, such as those in laser-driven experiments. The incorporation of microinertia allows us to better understand the increase in apparent macroscopic spall strength seen at high strain rates. Correspondingly, we conclude that the incorporation of microinertial effects improves the model’s predictive capabilities. Microinertial effects result in more severe local tensile stresses that affect the damage evolution, and microinertia can play a significant role in the approach to the material’s ideal strength at extreme loading rates. Additionally, a preliminary parametric study is also carried out to investigate the role of microstructural aspects such as nucleation volume fraction and initial pore radius. One counter-intuitive result from the microinertial effects is that, for a given nucleation site volume fraction, having larger initial pore nucleation sites can lead to an improved macroscopic spall strength.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Impact of Plate Thickness and Joint Geometry on Residual Stresses in 347H Stainless Steel Welds

Weldments of 347H stainless steel are potentially susceptible to stress relaxation cracking at elevated service temperatures. Mitigation of stress relaxation cracking susceptibility within a multipass weld requires a good understanding of welding practices and manufacturing techniques to control high tensile residual stresses. Here in this work, the dependence of residual stress distribution in 347H stainless steel on base plate thickness, joint geometry design, and preheating condition was systematically investigated by using three-dimensional finite element models. The finite element models were validated through good agreement between neutron diffraction measurements and calculated elastic strains. The single-V-groove welds with and without a preheating step all produced similar peak von Mises residual stresses, above 450 MPa, within both the fusion zone and heat-affected zone (HAZ). In plates thicker than 0.5 in. (12.7 mm), high tensile residual stress could be observed in a relatively large area, from the middle of the plate thickness to underneath the top surface. A double-V groove shifted the high tensile stress area to the middle thickness of the weld. A single-J-groove weld was able to confine the residual stress to a very small region near the middle thickness within the fusion zone and suppressed the von Mises residual stress within the HAZ to below 400 MPa.

14 SOLAR ENERGY↗
DOE OSTI2021

Columnar Grain-driven Plasticity and Cracking in Nanotwinned FCC Metals

The mechanisms of strengthening and plasticity in columnar-grained metals with preferentially oriented nano-sized twins have been examined traditionally by considering dislocation processes, but rarely from the perspective of grain boundary (GB) deformation. Here, the effects of GB strain accommodation on plastic deformation in four different columnar-grained nanocrystalline nanotwinned (nt) face-centered-cubic metals (Cu, Ag, Al, and Ni) were studied by large-scale molecular dynamics simulations. It is observed that in tensile deformation parallel to coherent twin boundaries (CTBs), the dislocation mechanisms in each metal are identical and associated with GB emissions of jog and threading dislocations at small and large CTB spacings, respectively. However, CTB strengthening effects are increasingly more pronounced in columnar-grained nt metals as their shear modulus increases, which is rationalized by the dependence of GB stress concentrations on twin size, metal type and strain rate. Also, while flow stresses in nt-Cu, nt-Ag, and nt-Al metals increase linearly with decreasing CTB spacing, a maximum strength limit is reached in nt-Ni below a critical CTB spacing of 6 nm. The strength limit in nt-Ni results from columnar GB cracking induced by prominent GB sliding. For columnar-grained microstructures, GB sliding is equivalent in nt-Ag and nt-Al and slightly lower in nt-Cu but markedly higher in nt-Ni. These findings underscore the importance of new GB deformation mechanisms on plasticity and fracture in columnar-grained nt metals and enrich our understanding of CTB strengthening in fcc metals synthesized in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Burst Pressure Solutions of Thin and Thick-Walled Cylindrical Vessels

Pressure vessels (PVs) are widely used in the energy industry. Accurate burst pressure is critical to structural design and safe operation for both thin and thick-walled PVs. The traditional strength theories utilized a single-parameter material property, such as the yield stress or the ultimate tensile stress (UTS) to develop failure models for determining the yield or ultimate pressure carrying capacity in the PV design. The UTS-based Barlow formula is a typical burst pressure model developed from the Tresca strength theory that provides the basis for developing regulation rules and failure models for different industry design codes, such as ASME BPVC, ASME B31.3, and ASME B31G, among others. In order to reduce the conservatism of the Tresca strength model, ASME BPVC recently adapted failure models developed from the von Mises strength theory for the PV design and analysis. It has been commonly accepted that the burst pressure of pipelines depends on the UTS and strain hardening exponent, n, of the pipeline steel. An average shear stress yield theory was thus developed, and the Zhu-Leis solution of burst pressure was obtained as a function of UTS and n for thin-walled line pipes. Experiments showed that the Zhu-Leis solution provides an accurate, reliable prediction of burst pressure for defect-free thin-walled pipes. In order to extend the Zhu–Leis solution to thick-walled cylindrical PVs, this paper defined three new flow stresses, modified the traditional strength theories, and obtained three new burst pressure solutions that are valid for both thin and thick-walled cylindrical vessels. The proposed flow stresses are able to describe the tensile strength and the plastic flow response of PVs for a strain hardening steel. The associated strength theories were then developed in terms of the Tresca, von Mises, and Zhu-Leis yield criteria. From these new strength theories, three burst pressure solutions were obtained for thick-walled cylinders, where the von Mises solution is an upper bound prediction, the Tresca solution is a lower bound prediction, and the Zhu-Leis solution is an intermediate prediction of burst pressure for thick-walled cylinders. Lastly, the proposed burst pressure solutions were evaluated and validated by two large datasets of full-scale burst tests for thick-walled tubes and for thin-walled pipes.

42 ENGINEERING↗
DOE OSTI2020

Bicontinuous nanoporous design induced homogenization of strain localization in metallic glasses

Bicontinuous nanoporous metallic glasses (MG) synergize the outstanding properties of MGs and open-cell nanoporous materials. The low-density and high-specific-surface-area of bicontinuous nanoporous structures have the potential to enhance the applicability of MGs in catalysis, sensors, and lightweight structural designs. In this work, we report molecular dynamics simulations of tensile loading deformation and failure of bicontinuous nanoporous Cu 64 Zr 36 MG with 55% porosity and 4.4 nm ligament size. Results indicate an anomalous mechanical behavior featuring delocalized plastic deformation preceding ductile failure. The deformation follows two mechanisms: i) Necking of ligaments aligned with the loading direction and ii) progressive alignment of randomly oriented ligaments. Failure occurs at 0.16 strain, following massive rupture of ligaments. This work indicates that a bicontinuous nanoporous design is able to effectively delocalize strain localization in a MG due to a combination of size effect on the ductility of MGs resulting in nano ligaments necking and progressive asynchronous alignment of ligaments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Theoretical and experimental studies of compression and shear deformation behavior of Osmium to 280 GPa

Abstract The compression behavior of osmium metal was investigated up to 280 GPa (volume compression V/V o = 0.725) under nonhydrostatic conditions at ambient temperature using angle dispersive axial x-ray diffraction (A-XRD) with a diamond anvil cell (DAC). In addition, shear strength of osmium was measured to 170 GPa using radial x-ray diffraction (R-XRD) technique in DAC. Both diffraction techniques in DAC employed platinum as an internal pressure standard. Density functional theory (DFT) calculations were also performed, and the computed lattice parameters and volumes under compression are in good agreement with the experiments. DFT predicts a monotonous increase in axial ratio ( c/a ) with pressure and the structural anomalies of less than 1% in ( c/a ) ratio reported below 150 GPa were not reproduced in theoretical calculations and hydrostatic measurements. The measured value of shear strength of osmium ( τ ) approaches a limiting value of 6 GPa above a pressure of 50 GPa in contrast to theoretical predictions of 24 GPa and is likely due to imperfections in polycrystalline samples. DFT calculations also enable the studies of shear and tensile deformations. The theoretical ideal shear stress is found along the (001)[1–10] shear direction with the maximal shear stress ∼24 GPa at critical strain ∼0.13.

Lin, Chia-Min↗