Search NASA⌕ Search

SEARCH · Search NASA

Results for “Testing and Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Development of a Weather Robust Microphone Configuration for Sonic Boom Measurements

This paper discusses ongoing development and testing of ground-based, weather-robust microphone measurement systems in conjunction with preparation for community testing of the NASA X-59 quiet supersonic aircraft. Prior efforts [Anderson et al., Proc. Mtgs. Acoust. 42, 040005 (2022)] resulted in the refinement of a ground-plate setup by investigating varied windscreen and plate diameters and thicknesses. The most recent goal has been to make the setup more compact and easier to manufacture. This paper discusses the results of additional tests performed on updated designs meant to find the balance between compactness and performance. Anechoic chamber testing was performed to examine ground plate and windscreen performance and to compare results against prior versions. Outdoor tests included measurements during different wind conditions and over different ground surfaces to examine low-frequency wind noise reduction and ground impedance effects. Results discussed during the presentation suggest the new design strikes an acceptable compromise between compactness, manufacturing ease and robustness, and performance. [Work supported by NASA Langley Research Center through Analytical Mechanics Associates]

sonic boom↗
NASA NTRS2020

Preliminary Design, Testing, and Performance of the LOFTID Navigation System

The Low Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) involves the first orbital test of an inflatable decelerator. This test involves the LOFTID re-entry vehicle using an inflatable decelerator to re-enter the atmosphere after flying to orbit as a secondary payload. Due to system constraints, including spin stabilization, unknown time of day, a limited space available for antennas, and a heat shield which blocks magnetic fields, the navigation system includes only an inertial measurement unit and a single GPS receiver. As the vehicle is turned off for the first part of the mission and will not receive commands or data from the ground, the navigation system will not have accurate initialization, and will in-stead rely on pre-flight estimates or first measurement estimation. This could result in significant unknown error in the initial state, resulting in needing to initialize the state on-orbit and requires using the single GPS antenna for attitude updates. These design considerations led to using an Extended Kalman filter, modified to perform with these design constraints. A streamlined testing approach, including tests with flight-like rotations, is being used to limit the time and resources needed to test the navigation system while still fully testing the performance and robustness of the navigation system. This testing approach follows the NASA test-as-you-fly principle and allows for early detection of errors and changes that are needed in the software. This results in a navigation system that, even within the design constraints of the mission architecture, will provide the performance and robustness needed of the mission.

Joel Amert↗
NASA NTRS1986

Performance Evaluation Tests for Environmental Research (PETER): evaluation of 114 measures

The goal of the Performance Evaluation Tests for Environmental Research (PETER) Program was to identify a set of measures of human capabilities for use in the study of environmental and other time-course effects. 114 measures studied in the PETER Program were evaluated and categorized into four groups based upon task stability and task definition. The Recommended category contained 30 measures that clearly obtained total stabilization and had an acceptable level of reliability efficiency. The Acceptable-But-Redundant category contained 15 measures. The 37 measures in the Marginal category, which included an inordinate number of slope and other derived measures, usually had desirable features which were outweighed by faults. The 32 measures in the Unacceptable category had either differential instability or weak reliability efficiency. It is our opinion that the 30 measures in the Recommended category should be given first consideration for environmental research applications. Further, it is recommended that information pertaining to preexperimental practice requirements and stabilized reliabilities should be utilized in repeated-measures environmental studies.

NASA Program Space Medicine↗
NASA NTRS1985

Performance characterization tests of a 1-kW resistojet using hydrogen, nitrogen and ammonia as propellants

A performance mapping test of a 1 kW radiatively heated resistojet demonstrated high specific impulse and efficiency with hydrogen, nitrogen and ammonia as propellants. The resistojet was based on an unmodified augmentation section of the flight-qualified Rocket Research Company Augmented Catalytic Thruster. Peak specific impulse values of 686.9 sec for hydrogen, 191.6 sec for nitrogen, and 342 sec for ammonia were demonstrated. A maximum specific impulse efficiency of 94.3 percent was demonstrated with hydrogen. Testing covered a thrust range of 27 to 112 mlbf with augmentation powers ranging from 300 to 1000 watts. A total of 83 runs accumulating 25 hours of operation were conducted with the three propellants. Comparison of specific impulse efficiency to other published resistojet performance data showed the radiatively heated resistojet compares favorably to other design concepts.

Miyake, C. I.↗
NASA NTRS1998

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Engineering Test Report: AMSU-A1 EOS Instrument, (S/N 202) Qualification Level Vibration Tests of August/September 1998, (S/O 565632, OC-417) Plus Addendum A

The purpose of this report is to present a qualification level vibration testing performed on the S/N 202, EOS AMSU-A1 Instrument was vibration tested to qualification levels per the Ref. 1 shop order. The instrument withstood the 8 g sine sweep test, the 7.5 Grms random vibration test, and the 18.75 g sine burst test in each of the three orthogonal axes. Some loss of transmissibility, however, is seen in the lower reflector after Z-axis random vibration. The test sequence was not without incidence. Failure of Channel 7 in the Limited Performance Test (LPT) performed after completion of the 1 st (X-axis) axis vibration sequence, required replacement of the DRO and subsequent re-testing of the instrument. The post-vibration comprehensive performance test (CPT) was successfully run after completion of the three axes of vibration with the replacement component installed in the instrument. Passing the CPT signified the successful completion of the S/N 202 A1 qualification vibration testing.

Heffer, R.↗
NASA NTRS1981

NASA VCE test bed engine aerodynamic performance characteristics and test results

The Core Driven Fan Stage (CDFS) Variable Cycle Engine (VCE) has been identified as a leading candidate for advanced supersonic cruise aircraft. A scale demonstrator version of this engine has been designed and tested. This testbed engine features a split fan with double bypass capability, variable forward and aft mixers, and a variable area low pressure turbine nozzle to permit exploration and optimization of the cycle in both single and double bypass modes. This paper presents the aerodynamic performance characteristics and experimental results obtained from both the core engine and full engine tests.

French, M. W.↗
NASA NTRS1978

Long-term CF6 engine performance deterioration: Evaluation of engine S/N 451-479

The performance testing and analytical teardown of CF6-6D engine is summarized. This engine had completed its initial installation on DC-10 aircraft. The investigative test program was conducted inbound prior to normal overhaul/refurbishment. The performance testing included an inbound test, a test following cleaning of the low pressure turbine airfoils, and a final test after leading edge rework and cleaning the stage one fan blades. The analytical teardown consisted of detailed disassembly inspection measurements and airfoil surface finish checks of the as received deteriorated hardware. Included in this report is a detailed analysis of the test cell performance data, a complete analytical teardown report with a detailed description of all observed hardware distress, and an analytical assessment of the performance loss (deterioration) relating measured hardware conditions to losses in both SFC (specific fuel consumption) and EGT (exhaust gas temperature).

Kramer, W. H.↗
NASA NTRS1978

Long-term CF6 engine performance deterioration: Evaluation of engine S/N 451-380

The performance testing and analytical teardown of CF6-6D engine serial number 451-380 which was recently removed from a DC-10 aircraft is summarized. The investigative test program was conducted inbound prior to normal overhaul/refurbishment. The performance testing included an inbound test, a test following cleaning of the low pressure turbine airfoils, and a final test after leading edge rework and cleaning the stage one fan blades. The analytical teardown consisted of detailed disassembly inspection measurements and airfoil surface finish checks of the as-received deteriorated hardware. Aspects discussed include the analysis of the test cell performance data, a complete analytical teardown report with a detailed description of all observed hardware distress, and an analytical assessment of the performance loss (deterioration) relating measured hardware conditions to losses in both specific fuel comsumption and exhaust gas temperature.

Kramer, W. H.↗
NASA NTRS1978

The modular power subsystem for the multimission modular spacecraft

The block diagram, subsystems, and components of the modular power subsystem for the multimission modular spacecraft (MMS) are described. The basic design studies were guided by considerations of cost, efficiency, simplicity, and flexibility to serve a variety of missions. Components discussed are the power regulator unit, the power control unit, the signal conditioning assembly, bus protection assembly, and the 20 Ah and 50 Ah batteries. The plan for the modular power subsystem protoflight module tests is shown. The testing has four phases: (1) component level tests, (2) subsystem integration and initial performance test, (3) subsystem protoflight environmental tests, and (4) subsystem final performance tests, qualification/acceptance review and delivery.

Harris, D. W.↗
NASA NTRS1989

Performance and test section flow characteristics of the National Full-Scale Aerodynamics Complex 40- by 80-foot wind tunnel

Results from the performance and test section flow calibration of the 40- by 80-Foot Wind Tunnel are presented. A flow calibration test was conducted in May and June 1987. The goal of the flow calibration test was to determine detailed spatial variations in the 40- by 80-ft test section flow quality throughout the tunnel operational envelope. Data were collected for test section speeds up to 300 knots and for air exchange rates of 0, 5, and 10 percent. The tunnel performance was also calibrated during the detailed mapping of the test section flow field. Experimental results presented indicate that the flow quality in the test section, with the exception of temperature, is relatively insensitive to the level of dynamic pressure and the air exchange rate. The dynamic pressure variation in the test section is within + or - 0.5 deg at all test section velocities. Cross-stream temperature gradients in the test section caused by the air exchange system were documented, and a correction method was established. Streamwise static pressure variation on the centerline is about 1 percent of test section dynamic pressure over 30 ft of the test section length.

Zell, Peter T.↗
NASA NTRS1993

Performance and test section flow characteristics of the National Full-Scale Aerodynamics Complex 80- by 120-Foot Wind Tunnel

Results from the performance and test section flow calibration of the 80- by 120-Foot Wind Tunnel are presented. Measurements indicating the 80- by 120-ft test section flow quality were obtained throughout the tunnel operational envelope and for atmospheric wind speeds up to approximately 20 knots. Tunnel performance characteristics and a dynamic pressure system calibration were also documented during the process of mapping the test section flow field. Experimental results indicate that the test section flow quality is relatively insensitive to dynamic pressure and the level of atmospheric winds experienced during the calibration. The dynamic pressure variation in the test section is within +/-75 percent of the average. The axial turbulence intensity is less than 0.5 percent up to the maximum test section speed of 100 knots, and the vertical and lateral flow angle variations are within +/-5 deg and +/-7 deg, respectively. Atmospheric winds were found to affect the pressure distribution in the test section only at high ratios of wind speed to test section speed.

Zell, Peter T.↗
NASA NTRS2007

Preliminary Low Temperature Electron Irradiation of Triple Junction Solar Cells

For many years extending solar power missions far from the sun has been a challenge not only due to the rapid falloff in solar intensity (intensity varies as inverse square of solar distance) but also because some of the solar cells in an array may exhibit a LILT (low intensity low temperature) degradation that reduces array performance. Recent LILT tests performed on commercial triple junction solar cells have shown that high performance can be obtained at solar distances as great as approx. 5 AU1. As a result, their use for missions going far from the sun has become very attractive. One additional question that remains is whether the radiation damage experienced by solar cells under low temperature conditions will be more severe than when measured during room temperature radiation tests where thermal annealing may take place. This is especially pertinent to missions such as the New Frontiers mission Juno, which will experience cell irradiation from the trapped electron environment at Jupiter. Recent testing2 has shown that low temperature proton irradiation (10 MeV) produces cell degradation results similar to room temperature irradiations and that thermal annealing does not play a factor. Although it is suggestive to propose the same would be observed for low temperature electron irradiations, this has not been verified. JPL has routinely performed radiation testing on commercial solar cells and has also performed LILT testing to characterize cell performance under far sun operating conditions. This research activity was intended to combine the features of both capabilities to investigate the possibility of any room temperature annealing that might influence the measured radiation damage. Although it was not possible to maintain the test cells at a constant low temperature between irradiation and electrical measurements, it was possible to obtain measurements with the cell temperature kept well below room temperature. A fluence of 1E15 1MeV electrons was selected as representative of a moderately high dose that might be expected for a solar powered mission. Fluences much greater than this would require large increases in array area and mass, compromising the ability of PV to compete with non-solar alternatives.

Stella, Paul M.↗
NASA NTRS2010

Refractory Metal Heat Pipe Life Test - Test Plan and Standard Operating Procedures

Refractory metal heat pipes developed during this project shall be subjected to various operating conditions to evaluate life-limiting corrosion factors. To accomplish this objective, various parameters shall be investigated, including the effect of temperature and mass fluence on long-term corrosion rate. The test series will begin with a performance test of one module to evaluate its performance and to establish the temperature and power settings for the remaining modules. The performance test will be followed by round-the-clock testing of 16 heat pipes. All heat pipes shall be nondestructively inspected at 6-month intervals. At longer intervals, specific modules will be destructively evaluated. Both the nondestructive and destructive evaluations shall be coordinated with Los Alamos National Laboratory. During the processing, setup, and testing of the heat pipes, standard operating procedures shall be developed. Initial procedures are listed here and, as hardware is developed, will be updated, incorporating findings and lessons learned.

Martin, J. J.↗
NASA NTRS2001

Improving the Total Impulse Capability of the NSTAR Ion Thruster With Thick-Accelerator-Grid Ion Optics

The results of performance tests with thick-accelerator-grid (TAG) ion optics are presented. TAG ion optics utilize a 50 percent thicker accelerator grid to double ion optics' service life. NSTAR ion optics were also tested to provide a baseline performance for comparison. Impingement-limited total voltages for the TAG ion optics were only 0 to 15 V higher than those of the NSTAR ion optics. Electron backstreaming limits for the TAG ion optics were 3 to 9 V higher than those for the NSTAR optics due to the increased accelerator grid thickness for the TAG ion optics. Screen grid ion transparencies for the TAG ion optics were only about 2 percent lower than those for the NSTAR optics, reflecting the lower physical screen grid open area fraction of the TAG ion optics. Accelerator currents for the TAG ion optics were 19 to 43 percent greater than those for the NSTAR ion optics due, in part, to a sudden increase in accelerator current during TAG ion optics' performance tests for unknown reasons and to the lower-than-nominal accelerator aperture diameters. Beam divergence half-angles that enclosed 95 percent of the total beam current and beam divergence thrust correction factors for the TAG ion optics were within 2 degrees and 1 percent, respectively, of those for the NSTAR ion optics.

Soulas, George C.↗
NASA NTRS1985

Preliminary evaluation of a micro-based repeated measures testing system

A need exists for an automated performance test system to study the effects of various treatments which are of interest to the aerospace medical community, i.e., the effects of drugs and environmental stress. The ethics and pragmatics of such assessment demand that repeated measures in small groups of subjects be the customary research paradigm. Test stability, reliability-efficiency and factor structure take on extreme significance; in a program of study by the U.S. Navy, 80 percent of 150 tests failed to meet minimum metric requirements. The best is being programmed on a portable microprocessor and administered along with tests in their original formats in order to examine their metric properties in the computerized mode. Twenty subjects have been tested over four replications on a 6.0 minute computerized battery (six tests) and which compared with five paper and pencil marker tests. All tests achieved stability within the four test sessions, reliability-efficiencies were high (r greater than .707 for three minutes testing), and the computerized tests were largely comparable to the paper and pencil version from which they were derived. This computerized performance test system is portable, inexpensive and rugged.

Kennedy, Robert S.↗
NASA NTRS2020

The World’s Largest Wind Tunnels: Their History, Contributions to Aeronautics, and Importance to Flight - A History of the NASA Ames 40- by 80-Foot and 80- by 120-Foot Wind Tunnels

This book describes the history of the facility in some detail. Modifications to the tunnel are described along with much of the research and development testing performed over the years. Often models or aircraft were studied in the facility and then modified and tested again, such that many models and aircraft were tested numerous times over a period of several years. Descriptions generally cover investigations of models that occurred for several years, rather than descriptions of tests performed chronologically. The goal has been to make the descriptions understandable and not particularly technical, but yet clearly state their purposes. Not all tests are described because of the large number of tests performed (on the order of 700), but many representative tests are described that are intended to illustrate the variety and importance of the models and aircraft investigated over the years. A comprehensive list of references is included for those who are interested in more technical details. It should be noted that after the implementation of full-cost recovery, the interest of NASA in producing traditional reports on aerodynamics was substantially reduced. As a result, there were fewer NASA aeronautical reports in later years. This was a disappointing development because of the importance and high quality of the NASA reports and the importance of archiving results of unique experiments. Dates of important events are provided in Appendix A and a list of NFAC tests are provided in Appendix B. This book is organized in four parts: Part I. Design and Construction; Part II. Operation and Management History; Part III. Research History; and Part IV. Concluding Remarks, References, and Appendices.

World’s Largest Wind Tunnels↗