Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wind tunnel models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Characterization of Pressure Sensitive Paint Intrusiveness Effects on Aerodynamic Data

One effect of using pressure sensitive paint (PSP) is the potential intrusiveness to the aerodynamic characteristics of the model. The paint thickness and roughness may affect the pressure distribution. and therefore, the forces and moments on the wind tunnel model. A study of these potential intrusive effects was carried out at NASA Langley Research Center where a series of wind tunnel tests were conducted using the Modem Design of Experiments (MDOE) test approach. The PSP effects on the integrated forces were measured on two different models at different test conditions in both the Low Turbulence Pressure Tunnel (LTPT) and the Unitary Plan Wind Tunnel (UPWT) at Langley. The paint effect was found to be very small over a range of Reynolds numbers, Mach numbers and angles of attack. This is due to the very low surface roughness of the painted surface. The surface roughness, after applying the NASA Langley developed PSP, was lower than that of the clean wing. However, the PSP coating had a localized effects on the pressure taps, which leads to an appreciable decrease in the pressure tap reading.

Amer, Tahani R.↗
NASA NTRS1985

Analysis of holographic interferograms of aerodynamic models in a wind tunnel

Holographic interferometry provides a non-invasive technique for estimating variations in the air density distribution around aerodynamic models in wind tunnels. The testing of this technique has been underway for some time and has been reported previously for a two dimensional aerodynamic model. Results obtained from tests using three dimensional aerodynamic models are summarized. Holograms were made of aerodynamic models in a wind tunnel. Interferograms were made from these holograms. The interference fringes in these holographic interferograms were digitized and this information was entered into the HOLOFT program. The HOLOFT program successfully calculated the known stagnation air density at the nose of a model and the known air density distribution across the cross section passing through the stagnation point for the axisymmetrical case of this model at a Mach number of 0.8. Thus the technique of holographic interferometry does work.The HOLOFT program stands for HOLOgraphic Inversion by 2-D Fourier Transform.

Perry, R. L.↗
NASA NTRS1984

Remotely controlled models slash tunnel time

The employment of a remote-control model system makes it possible to reduce the wind-tunnel time and cost required to define the aerodynamics f a configuration. In support of the Space Shuttle program, several wind-tunnel models with remote-controlled elevons, body flap, and rudder were designed, built, and tested. The models have been tested at Mach numbers in the range from 0.30 to 4.5 and dynamic pressures greater than 2,000 psf. Attention is given to a model for Shuttle approach and landing tests, a model to define the aerodynamic characteristics of the final Shuttle Orbiter configuration, and the time savings made with a remotely controlled model.

Ware, G. M.↗
NASA NTRS1989

Influence of wing geometry on leading-edge vortices and vortex-induced aerodynamics at supersonic speeds

An assessment of the influence of wing geometry on wing leading-edge vortex flows at supersonic speeds is discussed as well as the applicability of various aerodynamic codes for predicting these results. A series of delta-wing wind-tunnel models were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel over a Mach number range from 1.6 to 4.6. The data show that wing airfoil has a significant impact on the localized loading on the wing. The experimental data for the flat wings were compared with results from full-potential, Euler, and Parabolized Navier-Stokes (PNS) computer codes. The theoretical evaluation showed that the full-potential analysis predicted accurate results for the attached-flow (alpha = 0 deg) conditions and that the Euler and PNS analyses made reasonable predictions for both attached and separated flow conditions.

Wood, Richard M.↗
NASA NTRS1997

BACT Simulation User Guide (Version 7.0)

This report documents the structure and operation of a simulation model of the Benchmark Active Control Technology (BACT) Wind-Tunnel Model. The BACT system was designed, built, and tested at NASA Langley Research Center as part of the Benchmark Models Program and was developed to perform wind-tunnel experiments to obtain benchmark quality data to validate computational fluid dynamics and computational aeroelasticity codes, to verify the accuracy of current aeroservoelasticity design and analysis tools, and to provide an active controls testbed for evaluating new and innovative control algorithms for flutter suppression and gust load alleviation. The BACT system has been especially valuable as a control system testbed.

Waszak, Martin R.↗
NASA NTRS1975

Effect of wing planform and canard location and geometry on the longitudinal aerodynamic characteristics of a close-coupled canard wing model at subsonic speeds

A generalized wind-tunnel model with canard and wing planforms typical of highly maneuverable aircraft was tested in the Langley 7- by 10-foot high-speed tunnel at a Mach number of 0.30 to determine the effect of canard location, canard size, wing sweep, and canard strake on canard-wing interference to high angles of attack. The major results of this investigation may be summarized as follows: the high-canard configuration (excluding the canard strake and canard flap), for both the 60 deg and 44 deg swept leading-edge wings, produced the highest maximum lift coefficient and the most linear pitching-moment curves; substantially larger gains in the canard lift and total lift were obtained by adding a strake to the canard located below the wing chord plane rather than by adding a strake to the canard located above the wing chord plane.

Gloss, B. B.↗
NASA NTRSDate not supplied

Degradation Characterization of Unsteady Pressure-Sensitive Paint Under Various Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the uPSP, this paper describes the efforts to characterize the degradation of both the intensity of the paint and its lifetime ratio, as well as the change in intensity calibration. It was found that the paint degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when under higher oxygen concentrations, both indicating photodegradation due to photodecomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel. The work provides insight into the dynamic degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS1999

Determination of Stability and Control Derivatives using Computational Fluid Dynamics and Automatic Differentiation

With the recent interest in novel control effectors there is a need to determine the stability and control derivatives of new aircraft configurations early in the design process. These derivatives are central to most control law design methods and would allow the determination of closed-loop control performance of the vehicle. Early determination of the static and dynamic behavior of an aircraft may permit significant improvement in configuration weight, cost, stealth, and performance through multidisciplinary design. The classical method of determining static stability and control derivatives - constructing and testing wind tunnel models - is expensive and requires a long lead time for the resultant data. Wind tunnel tests are also limited to the preselected control effectors of the model. To overcome these shortcomings, computational fluid dynamics (CFD) solvers are augmented via automatic differentiation, to directly calculate the stability and control derivatives. The CFD forces and moments are differentiated with respect to angle of attack, angle of sideslip, and aircraft shape parameters to form these derivatives. A subset of static stability and control derivatives of a tailless aircraft concept have been computed by two differentiated inviscid CFD codes and verified for accuracy with central finite-difference approximations and favorable comparisons to a simulation database.

Park, Michael A.↗
NASA NTRSDate not supplied

Characterization of Photodegredation in Unsteady Pressure-Sensitive Paint Under Varying Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the unsteady pressure-sensitive paint (uPSP), this paper describes the efforts to characterize how photo degradation affects the intensity of the paint signal and its lifetime ratio, as well as the intensity calibration's response and how these changes vary with different pressure environments. It was found that the paint photo degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when exposed to excitation light in higher pressure environments, both indicating photo degradation due to photo decomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel as well as a large-scale 11’ x 11’ transonic wind tunnel. The work provides analysis into the photo degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS1983

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley continuous flow hypersonic tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests wre completed in the Langley Continuous Flow Hypersonic Tunnel (CFHT). The 0.04-scale model was tested at angles of attack from -5 deg to 45 deg and angles of sideslip from -3 deg to 3 deg. The 0.02-scale model was tested at angles of attack from -10 deg to 45 deg and angles of sideslip from -5 deg to 5 deg. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗
NASA NTRS1987

Fifteenth NASTRAN (R) Users' Colloquium

Numerous applications of the NASA Structural Analysis (NASTRAN) computer program, a general purpose finite element code, are discussed. Additional features that can be added to NASTRAN, interactive plotting of NASTRAN data on microcomputers, mass modeling for bars, the design of wind tunnel models, the analysis of ship structures subjected to underwater explosions, and buckling analysis of radio antennas are among the topics discussed.

Source record↗
NASA NTRS1988

Computational design of low aspect ratio wing-winglet configurations for transonic wind-tunnel tests

A computational design has been performed for three different low aspect ratio wing planforms fitted with nonplanar winglets; one of the three planforms has been selected to be constructed as a wind tunnel model for testing in the NASA LaRC 7 x 10 High Speed Wind Tunnel. A design point of M = 0.8, CL approx = 0.3 was selected, for wings of aspect ratio equal to 2.2, and leading edge sweep angles of 45 and 50 deg. Winglet length is 15 percent of the wing semispan, with a cant angle of 15 deg, and a leading edge sweep of 50 deg. Winglet total area equals 2.25 percent of the wing reference area. This report summarizes the design process and the predicted transonic performance for each configuration.

Kuhlman, John M.↗
NASA NTRS1989

Computational design of low aspect ratio wing-winglets for transonic wind-tunnel testing

A computational design has been performed for three different low aspect ratio wing planforms fitted with nonplanar winglets; one of the three planforms has been selected to be constructed as a wind tunnel model for testing in the NASA LaRC 7 x 10 High Speed Wind Tunnel. A design point of M = 0.8, CL approx = 0.3 was selected, for wings of aspect ratio equal to 2.2, and leading edge sweep angles of 45 and 50 deg. Winglet length is 15 percent of the wing semispan, with a cant angle of 15 deg, and a leading edge sweep of 50 deg. Winglet total area equals 2.25 percent of the wing reference area. This report summarizes the design process and the predicted transonic performance for each configuration.

Kuhlman, John M.↗
NASA NTRS1993

Experimental apparatus for optimization of flap position for a three-element airfoil model

It is proposed to design and build a wind tunnel model comprising a Douglas Aircraft Company three-element high-lift airfoil with internal actuators to move the flap vertically and horizontally under computer control. The model will be used to find the optimum flap location for a fixed angle of attack, slat position and flap deflection angle. The model will span the full tunnel width and lift will be measured by integration of pressure readings taken from midspan taps. It is proposed to conduct experiments in the NASA Langley EFPB 2' x 3' low speed wind tunnel. This report serves as a project overview and a review of work completed to date through funding by the 1993 NASA/ASEE Summer Faculty Fellowship Program.

Landman, Drew↗
NASA NTRS1971

Detailed investigation of flowfields within large scale hypersonic inlet models

Analytical and experimental investigations were conducted to determine the characteristics of the internal flows in model passages representative of hypersonic inlets and also sufficiently large for meaningful data to be obtained. Three large-scale inlet models, each having a different compression ratio, were designed to provide high performance and approximately uniform static-pressure distributions at the throat stations. A wedge forebody was used to simulate the flowfield conditions at the entrance of the internal passages, thus removing the actual vehicle forebody from consideration in the design of the wind-tunnel models. Tests were conducted in a 3.5 foot hypersonic wind tunnel at a nominal test Mach number of 7.4 and freestream unit Reynolds number of 2,700,000 per foot. From flowfield survey data the inlet entrance, the entering inviscid and viscous flow conditions were determined prior to the analysis of the data obtained in the internal passages. Detailed flowfield survey data were obtained near the centerlines of the internal passages to define the boundary-layer development on the internal surfaces and the internal shock-wave configuration. Finally, flowfield data were measured across the throats of the inlet models to evaluate the internal performance of the internal passages. These data and additional results from surface instrumentation and flow visualization studies were utilized to determine the internal flowfield patterns and the inlet performance.

Seebaugh, W. R.↗
NASA NTRS1992

Navier-Stokes calculation of transonic flow past the NTF 65-deg delta wing

Viscous flow past a wind tunnel model of a 65-degree swept angle Delta wing at transonic speeds is being studied. The model was tested in the 8-foot cryogenic transonic wind tunnel at the National Transonic Facility. Aerodynamic forces and wing surface pressure data were obtained at various angles of attack, Mach numbers, and Reynold's numbers for four different leading edges of the wing. The objectives of the present investigation are: (1) to perform numerical modeling of the flow around the wing; (2) to validate the experimental data with a Navier-Stokes computational fluid dynamics code and vice versa; (3) to investigate the effects of the sting mount of the wing; (4) to evaluate the effects of leading edge radius on the flow; and (5) to explain the Reynold's number effect as indicated by the test data. Several computer programs were developed to define the surfaces of the wing, the four leading edges, and the sting mount. Based on these geometric databases, the surface grids of a single-block computational domain was generated interactively on the IRIS workstation using the GRIDGEN2D module of GRIDGEN. To refine the grids and to avoid excessive loss of grid points due to collapsed edges, a 9-block computational domain containing approximately 750,000 grid points was developed with the GRIDBLOCK module to replace the single-block grid.

Wu, Chivey↗