Search NASA⌕ Search

SEARCH · Search NASA

Results for “advanced alloy development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Advances in Molecular Beam Epitaxy Growth of Ultra-Wide Bandgap Ga2O3 Based Alloys

Gallium oxide (Ga2O3) is an emerging ultra-wide bandgap semiconductor material that has attracted attention for its potential to outperform existing SiC and GaN based devices operating at high breakdown voltages and high temperature. Isovalent alloying of In and Al in Ga2O3 provides the ability to engineer bandgap energy and strain of the material. Alloying with Al increases the bandgap energy and the theoretically achievable Baliga's figure of merit, a key measure of a material's ultimate performance limits for high power switching devices. Alloying with In introduces compressive strain and can be used to counteract the tensile strain of Al incorporation. The resulting (AlxGa1-x-yIny)2O3 alloy can be lattice-matched to commercially available Ga2O3 wafers and has a tunable bandgap energy greater than that of Ga2O3, 4.76 eV. Such lattice-matched material can be grown arbitrarily thick without the detrimental effects of elastic strain and relaxation, making it suitable for high voltage diodes and transistors. However, efforts to synthesize isovalent alloys are complicated by their tendency to phase separate into corundum Al2O3 or bixbyite In2O3. Literature reports of the quaternary (AlxGa1-x-yIny)2O3 are limited to <1% unintentional indium incorporation in In-catalyzed (AlxGa1-x)2O3. The primary limitation to quaternary growth is the limited incorporation of indium at elevated growth temperatures. This limited incorporation is due to both the volatility of indium oxide and Al and Ga cation exchange reactions which replace indium in In2O3. We report on the development of a novel high-throughput molecular beam epitaxy (MBE) technique to screen the growth conditions for the ternary alloy (InyGa1-y)2O3, and the application of these findings to the first successful synthesis of phase pure monoclinic (AlxGa1-x-yIny)2O3 by MBE. By leveraging the unique sub-oxide chemistry of Ga2O3 and in-situ monitoring of crystal properties by reflection high-energy electron diffraction (RHEED), a cyclical growth and etch-back method is developed and applied to rapidly characterize the (InyGa1-y)2O3 growth space. This cyclical method provides approximately 10x increase in experimental throughput and up to 46x improvement in Ga2O3 substrate utilization. Appropriate growth conditions for monoclinic (InyGa1- y)2O3 are identified by machine learning analysis of RHEED patterns and targeted growths are characterized ex-situ to confirm improved In incorporation. These growth conditions are then combined with established (AlxGa1-x)2O3 growth conditions to grow quaternary (AlxGa1-x-yIny)2O3 with Al mole fractions ranging from 1.4% - 24.4% and In mole fractions ranging from 3.1% to 15.5%. The chemical and optical properties of the alloys are investigated by XRD, XPS, and spectroscopic ellipsometry. A lattice-matched (AlxGa1-x-yIny)2O3 alloy is examined by 4D-STEM and the chemical and physical uniformity of Al and In incorporation are discussed.

alloy↗
DOE OSTI2021

CHARGED POINT DEFECTS AND DEFECT COMPLEXES IN PHOSPHORENE AND STRUCTURAL PREDICTION OF TAU-11, A DENSITY FUNCTIONAL THEORY APPROACH

With the advent of powerful computers, first principle calculations have become a robust and reliable tool to complement experiments in the study of materials. First principle calculations such as density functional theory can be used to guide experiments to save time and effort when it comes to new and advanced materials discovery. Study of charge defects in materials and crystal structure prediction are such areas in which density functional theory calculations facilitate the prediction of defect formation energy, charge transition levels and elemental site occupations. Experimentally, studying charge defects requires inferring results from various techniques. Likewise, determining site occupancies for similar elements using experimental techniques is challenging and sometimes impossible. In this work, we study the charged intrinsic and extrinsic defects and defect complexes in phosphorene and determine the site occupancies of Al, Fe and Si in the τ11 phase using density functional theory. In the defect work, we calculate the defect formation energy, charge transition level, binding energies and Stokes shift for vacancy, dopant substitution and dopant-vacancy defect complexes in phosphorene. We found that vacancy defect in phosphorene becomes negatively charged in n-type doping and may passivate the dopants and reduce carrier concentration and mobility. For non-metal dopants in phosphorene, we predict that O, S and Si prefer to form dopant-vacancy complexes removing the vacancy defect states from the band gap. Mn dopant-vacancy defect complex exhibits possibility of switching between two magnetic spin states. Lastly, using density functional theory, we complement the results from neutron powder diffraction to determine the site occupancies of Al and Si in τ11 phase which was used to determine the alloying element to develop a high temperature and low density alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Burst characteristics of advanced accident-tolerant FeCrAl cladding under temperature transient testing

Here assessment of burst characteristics of accident-tolerant fuel (ATF) claddings is essential to evaluate the safety margins of nuclear reactors, and better understanding can enable accelerated licensing for reactor concepts that include the new materials. Therefore, this study investigated the burst behavior of an ATF candidate of C26M, which is an iron–chromium–aluminum alloy (FeCrAl) under transient testing like the simulated loss-of-coolant accident (LOCA) conditions, except the water-quenching phase, in light-water reactors (LWRs). The effect of LOCA specimen length was assessed in terms of post-burst tube parameters. No critical length effect was determined on the burst pressure, burst location, and burst size measurements. Burst temperature showed larger variation likely due to its measurement approach used in this study. The post-test diametral strain was identified as the critical parameter to reduce the specimen length as compared to tube burst length or width. Postmortem optical metrology and digital image correlation were employed to determine the local strain-state during the simulated LOCA, which showed the loading path was close to equibiaxial conditions in regions away from the burst location, rather than internally pressurized conditions (or “plane-strain” tension). Pst-test microstructural characterizations of the FeCrAl revealed that ductile damage was present at the edge of the outer radial surface while the rest of the material was ruptured via cleavage at LOCA burst temperatures. Furthermore, internal grain boundary cracks were observed at locations away from the tube burst region. This behavior was considered to occur during the cooling down period of the simulated LOCA test. Overall, this study aimed to provide essential data for fuel performance code development by considering micromechanics of the deformation and failure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗
DOE OSTI2025

Development of Engine Valve Materials for Next Generation Higher Efficiency Engines

The growing demand to increase the performance and efficiency of light-, medium-, and heavy-duty engines continues to drive increases in combustion intensities and cylinder pressures, which result in higher exhaust gas temperatures. Thus, there is a critical need for new materials that can meet the performance and cost targets for components such as exhaust valves which are exposed to these higher exhaust gas temperatures. Oak Ridge National Laboratory (ORNL) has developed several lower-cost, high-strength alloys that have the potential to be adopted into intake and/or exhaust valves in the next generation, high-efficiency engines and other high temperature applications. These alloys are covered by two issued patents: 1. G. Muralidharan, U. S. Patent No. 9,605,565 B2, “Low-cost Fe--Ni--Cr alloys for high temperature valve applications,” March 28, 2017. 2. G. Muralidharan, U. S. Patent 9,752, 468 B2, “Low-Cost, High-Strength Fe-Ni-Cr Alloys for High Temperature Exhaust Valve Applications, Issued Sep. 5, 2017. The overall scope of this CRADA project was for Oak Ridge National Laboratory to collaborate with Tenneco Powertrain to: 1) better define the properties required for intake and/or exhaust valves for next generation vehicles, 2) fabricate industrial scale heats of alloys down-selected from existing patents, 3) generate critical high temperature property data that will help evaluate the suitability of these new alloys for high temperature intake and/or exhaust valves, and finally to 4) fabricate and evaluate the performance of prototype intake/and or exhaust valves.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated temperatures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple)trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A Baseline CFD model is defined and its accuracy established to be comparable to(and which usually exceeds) the accuracy of existing HTC (heat-transfer coefficient) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled),generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.1

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Mechanical Properties and Deformation Behavior of Additively Manufactured 316L Stainless Steel (FY2020)

The Transformational Challenge Reactor (TCR) program plans to build most of the TCR core components through additive manufacturing (AM) processes. These processes include laser powder bed fusion (LPBF) for the metallic (316L) components and the newly developed combined process of binderjet printing and chemical vapor infiltration (CVI) for the SiC fuel matrix. Mechanical testing and characterization tasks have been carried out since the beginning of the TCR program to (1) build a property database for the AM materials that will be used in TCR core and (2) to assess the materials’ performance in TCR-relevant conditions. This document reports the outcome of the testing and characterization efforts for the fiscal year with a focus on the mechanical performance data of AM 316L stainless steel (SS). Baseline tensile testing over a wide temperature range of room temperature–600 °C was completed for the AM 316L alloy in as-built, stress-relieved, and solution-annealed conditions. The as-built 316L showed the highest strength, and the alloy after the post-build treatments showed reduced strengths in the low-strain range. However, the strength differences among the AM materials became insignificant in the later part of deformation. Furthermore, regardless of post-build processing, the AM 316L SS showed higher strength and comparable ductility when compared with wrought 316L SS. Thermal creep testing and microstructural evolution during creep deformation were also performed under selected conditions. It was found that the AM 316L steel showed the best creep resistance in the stress-relieved condition. In-situ tensile tests were performed using scanning electron microscopy and 1-ID beamline at the Advanced Photon Source to elucidate the deformation and fracture behavior of AM 316L and the evolution of crystalline stress, dislocations, and pore distribution. Using these in-situ testing data, an in-depth analysis of the roles of microstructural features in deformation and fracture processes is presented herein. The final section of the document introduces ongoing and future activities for materials testing and characterization, including irradiation effect studies and ball punch testing on AM 316L and AM IN718 alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Quench process modeling & simulation in the heat-treatment of critical aerospace components

To manufacture light-weight, advanced metal alloy components for gas turbine engines, quench heat-treatment processes are typically used. By quenching the component from elevated tempera-tures, the alloy sometimes undergoes a solid-state phase transformation which produces special microstructures with the required, enhanced mechanical properties. However, the quenching can also lead to cracks forming in the component. Addressing the quench cracking problems adds a significant burden to the cost, schedule, and energy demand of manufacture. Currently, optimizing the quench process to mitigate or avoid the cracking is performed largely by trial-and-error, relying heavily on costly experimental (thermocouple) trials to understand the local thermal gradients which cause the cracks to form. In this first part (Phase 1) of the work, high-performance computing is employed to establish the ability of modern CFD (computational fluid dynamics) to alleviate or wholly replace the experimental quenching trials by virtual testing. A baseline CFD model is defined and its accuracy established to be comparable to (and which usually exceeds) the accuracy of existing HTC (heat-transfer correlation) based simulation methods of quenching. As a first-principles based approach, “calibration” of the Baseline CFD model is independent of the quench process itself, but instead relies on the accuracy of the underlying (modeled), generic two-phase fluid processes which cannot be currently resolved by CFD for large, industrial-scale cases. A novel, high-fidelity DNS capability has been developed and verified to examine and further improve upon the mean-field closure submodels on which the Baseline CFD approach is based.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding the deformation behavior of the γ rich transformative Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy using in situ synchrotron diffraction

In situ tensile testing coupled with synchrotron x-ray diffraction was used to study the deformation behavior of metastability-engineered Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy. Monitoring the evolution of phase fraction and strain hardening response allowed the determination of true critical stress for the onset of the transformation-induced plasticity (TRIP) to be ∼375 MPa, preceded by slip starting at ∼255 MPa. In situ EBSD was used to validate the critical stress for transformation at the microstructure level and observe slip traces to confirm prior slip activity before the transformation. Further, a modeling framework based on stacking fault energy (SFE) was developed to predict the critical stress for transformation. Modeling suggested the SFE of the alloy to fall nearly 15 mJ/m 2 , which agrees well with SFE values calculated using synchrotron peak shifting (12 mJ/m 2 ) and thermodynamic calculation (11 mJ/m 2 ). As a result of γ-fcc to ε-hcp phase transformation, new {0002} ε planes emerged parallel to unaligned {111} γ planes with the tensile loading following S-N orientation relationship. Such selective emergence of new diffraction rings corresponding to ε phase is understood based on the reorientation of γ crystals with reference to tensile axis. In conclusion, this approach can be extended to effectively design alloys based on critical stress required for activating different deformation mechanisms to further push the limits of the strength-ductility envelope.

Complex concentrated alloy↗
DOE OSTI2022

New challenges in oxygen reduction catalysis: a consortium retrospective to inform future research

In this perspective, we highlight results of a research consortium devoted to advancing understanding of oxygen reduction reaction (ORR) catalysis as a means to inform fuel cell science. We demonstrate how targeted collaborations between different institutions from academic, national lab, and industry backgrounds and different scientific disciplines like theory, experiment, and characterization can yield unique insights into fuel cell catalysts. We comment on such insights into material designs for platinum-group-metal alloys, transition metal oxides, and non-traditional materials including metal–organic frameworks; systems that have served as the foundational building blocks for our consortium. We also motivate a renewed focus on catalyst durability in light of emerging technological requirements and paths forward in understanding in situ and operando electrochemical stability. Lastly, we describe new frontiers ORR research can take and how emerging artificial intelligence tools can assist researchers in capturing data, selecting new experiments, and guiding characterization to accelerate the design and discovery of fuel cell catalysts. A main goal of sharing this perspective is to discuss the rationale for our future research plans based on our consortium work. However, we also hope to illustrate both the potential impact of a collaborative strategy with the hopes of inspiring a higher degree of Industry-Academia-National Laboratory collaboration and encourage other centers and consortiums to distill and share their findings in a similar perspective-type article. Together we hope to enable the fuel cell research community to engage in a discussion of strategies for research and accelerated development of catalysts with improved activity and stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Draft ASME Boiler and Pressure Vessel Code Cases and Technical Bases for Use of Alloy 617 for Constructions of Nuclear Component Under Section III, Division 5

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code currently only allows five materials for use in construction of nuclear components for high temperature service. These are: 2.25Cr-1Mo and V-modified 9Cr-1Mo steels, Types 304 and 316 stainless steels and the high nickel Alloy 800H. Since 2005, the US high temperature gas-cooled reactor program has been characterizing elevated temperature mechanical properties of Alloy 617 as the leading candidate construction material for the intermediate heat exchanger. After analysis of these experimental results, along with historical data and additional results available through the Generation IV International Forum, Very High Temperature Reactor, Materials Program Management Board Materials Handbook, a draft ASME Code Case to allow nuclear construction with Alloy 617 for temperatures up to 1750°F (954°C) has been developed. This report contains the Code Case for Low Temperature Service Construction of Section III, Division 5, Subsection HB, Subpart A, Class A and Subsection HC, Subpart A, Class B components, which has been approved in Section II, Materials, and Section III, Rules for Construction of Nuclear Facility Components. Supporting technical justification for the low temperature Code Case is also included. This Code Case allows use of Alloy 617 up to 800°F (425°C). This report also contains an updated draft of a Section III, Division 5, Subsection HB, Subpart B, Class A Code Case for Alloy 617 to qualify it for use in construction of nuclear components up to 1750°F (954°C) for service life up to 100,000 hours. The draft contained in Appendix 4, subject to editorial revision and approval by the ASME Special Task Group on Alloy 617 Code Qualification, will be submitted for approval by letter ballot by the appropriate ASME Committees. The technical justification supporting the Code Case is presented in Appendix 5 of this report. This background document is part of the information package that will be submitted with the Code Case for ballot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Overview of advanced plasma-facing materials testing for Fusion Pilot Plants at DIII-D

Characterization and testing of advanced plasma-facing materials (PFMs) for Fusion Pilot Plants (FPP) is being conducted at the DIII-D National Fusion Facility through the ongoing two-year FPP Candidate Materials Thrust. Year one tested 17 novel materials utilizing the Divertor Materials Evaluation System (DiMES), with samples analyzed pre- and post-experiment via SEM, EDS, and confocal microscopy. Repeatable reference discharges were developed to ensure uniformity between experiments, including a new strike-point rastering scenario to provide more uniform heat/particle flux across DiMES during ELMing H-mode discharges. Various sample geometries and temperatures were used to achieve FPP-relevant conditions, including samples angled 10° towards the incident plasma flux and pre-heating up to 500 °C. The first exposure of liquid lithium (Li) capillary porous structures in a tokamak demonstrated uniform emission of Li vapor and suppression of Li droplets in H-mode when preheated to 350 °C. Dispersoid-strengthened W with 1 wt% TaC, TiC, and ZrC exposed to H-mode showed cracking and dispersoid ejection for all varieties except TiC, providing a clear down-selection. Ultra-high temperature ceramic materials TiB 2 and ZrB 2 showed minimal degradation under L-mode exposure. Silicon carbide (SiC) fiber composites showed arcing along edges, while CVD SiC remained pristine. Atmospheric plasma-sprayed W and SiC coatings endured H-mode exposure without macroscopic delamination; SiC exhibited granular ejection, while W showed increased outgassing. Additional W-based alloys were stress tested in H-mode, including Ni-based W heavy alloys, W f SiC f /W composites, W multi-principle element alloys, and functionally-graded W/SiC, to varying degrees of success.

DIII-D↗
DOE OSTI2024

Influence of Nb alloying on Nb recrystallization and the upper critical field of Nb 3 ⁢Sn

Nb 3 Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, J c , of present Nb 3 Sn conductors declines swiftly above 12-15 T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, H c2 , values of ~ 24-26.5 T (4.2 K) and do not reach the FCC target J c , which serves as the present stretch target for Nb 3 Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance H c2 . In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of H c2 enhancement through alloying. H c2 (T) was measured for all samples in fields up to 16 T and some up to 31 T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (α) and spin-orbit scattering parameter (λ so ). The evaluation of dH c2 /dT near T c , which is proportional to the electronic specific heat coefficient γ and the normal state resistivity ρn, allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance H c2 (0) by 3-4 T to ~28 T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise H c2 (0) to ~31 T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C – 750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. Furthermore, the potential for further advancements in Nb 3 Sn properties is explored in relation to the recrystallization of the Nb alloy and the factors controlling the upper critical field.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Boride-based Ceramic Super-high Temperature Thermocouples in Harsh Environments (Final Scientific/Technical Report)

An electromotive force (emf) can be generated along a temperature gradient between the cold end and hot end of a thermoelectric material, termed the Seebeck effect. Based on the Seebeck effect, metallic alloys have been extensively employed to detect temperatures for centuries, named thermocouples. However, commercially available thermocouple alloys suffer from limitations, such as oxidation, chemical degradation, and poor long-term stability under high-temperature harsh environments. This DOE-funded project aimed to develop high-temperature, chemically tolerant thermocouples suitable for operation in extreme environments relevant to semiconducting thermoelectric materials. The research focused on boride-based semiconducting thermoelectric compounds as candidates for next-generation thermocouples with enhanced oxidation resistance, chemical stability, and thermal robustness under conditions representative of charcoal-fired electricity facilities. During the funded years, boride materials were synthesized using an arc-plasma technique under ambient air and argon atmospheres, enabling scalable and cost-effective production compared with conventional boride fabrication methods. The synthesized borides were processed into nanostructured powders, followed by consolidation into dense bulk materials using a spark plasma sintering (SPS) bottom-up approach. Comprehensive characterization was performed, including microstructural analysis, electrical transport measurements, and optical and thermal property evaluation. Both p-type and n-type boride electric legs were fabricated and integrated into boride-based thermocouples. The thermal and irradiation stabilities of the boride nanomaterials and bulk thermoelectric materials were systematically evaluated to assess suitability for long-term operation in harsh environments. Additionally, 12 students were broadly hands-on trained spanning the full research workflow, including word processing and technical editing (e.g., LATEX for manuscript and poster preparation), data collection and analysis (using Python and related libraries and hardware interfaces), sample preparation (including arc-plasma synthesis and spark plasma sintering), and advanced characterization techniques (such as X-ray diffraction, UV–vis spectroscopy, electron microscopy, differential thermal analysis (DTA), and Seebeck coefficient measurements, etc). Overall, this project demonstrated the feasibility of boride-based thermoelectric materials as durable high-temperature thermocouples, providing a promising pathway toward robust temperature sensing technologies aligned with DOE energy infrastructure and extreme-environment monitoring needs.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Tuning austenite stability through prior microstructure control in a low-alloy Q&P steel

Quenching and partitioning (Q&P) processing is a widely accepted heat treatment methodology for creating high strength steels consisting of ferrite, martensite, and austenite, while maintaining relatively low manufacturing costs. Though the research on effects of prior microstructure is limited, an understanding of the heat treatment response of different starting microstructures is critical to processing and creating steels with complex microstructures that contain retained austenite and may afford opportunities to further optimize properties. This study investigates the influence of starting microstructure (ferrite/pearlite versus martensite) and prior levels of cold work (38 verses 58 %) on the microstructural development and mechanical properties of a 0.2 C-2.0 Mn-1.5 Si (wt.%) steel exposed to Q&P processing. Samples with a starting martensitic microstructure resulted in higher retained austenite fractions and a more homogeneous microstructure after Q&P processing compared to a starting microstructure of ferrite-pearlite. Starting martensitic microstructures also displayed higher work hardening rates and higher uniform elongations. Larger cold reductions saw accelerated dissolution kinetics and austenite formation during intercritical annealing, resulting in more similar final microstructures from the ferrite-pearlite and martensitic starting microstructures. Finally, the results presented here indicate that varying prior processing can be a route to manipulate and control austenite stability in a Q&P processed steel.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Process Intensification for Nanostructure Aluminum Extrusions

A new technology called Shear Assisted Processing and Extrusion (ShAPE™), pioneered at the Pacific Northwest National Laboratory (PNNL), has the potential to revolutionize the US extrusion industry. Maturation of the ShAPE™ process would create a new cross cutting US manufacturing technology that advances three key the objectives within AMO; namely, nanomaterials processing, process intensification, and materials for extreme and harsh environments. PNNL and SCM Metals Products, Inc. (SCM), a division of Kymera International, will collaborate to mature the ShAPE™ extrusion process beyond TRL 3 to increase the likelihood of its adoption by industry. PNNL’s custom (one-of-a-kind in the world) ShAPE™ machine will be used to extrude round rods of high strength aluminum alloy feedstock powder provided by SCM. As proof-of-concept, PNNL has previously extruded 5 mm diameter rods with SCM aluminum alloy powder AL-12.4TM. This project aims to scale up the process to a diameter of 25 mm while retaining the excellent mechanical properties achieved for the 5 mm diameter rods. The degree of process intensification with ShAPE™ will also be estimated. The primary objectives of this project are as follows. 1) Fabricate 25 mm diameter nanostructured extrusions in bulk, directly from AL-12.4TM aluminum alloy powder without the need for canning, degassing, compaction, and other intermediate steps typical of powder metallurgy extrusion. 2) Achieve a microstructure with an ultrafine grained (UFG <1 µm) aluminum matrix having refined and homogenously distributed nanoscale second phases. 3) Show that the ram force can be significantly reduced compared to conventional powder metallurgy extrusion of the same material and estimate the extent of process intensification that may be possible with ShAPE™. 4) Demonstrate improved high-temperature mechanical properties compared to conventional extrusion of the same material. The following tasks will be undertaken to achieve these objectives. PNNL will develop the die set and process parameters necessary to fabricate Al-12.4TM extrusions with a 25 mm diameter. Microstructural analysis will be performed by PNNL while mechanical testing will be conducted by SCM. With information learned from the process development and characterization, PNNL will perform an estimate of the degree of process intensification that may be possible with ShAPE™.

42 ENGINEERING↗
DOE OSTI2020

Oak Ridge National Laboratory Technical Input for the Nuclear Regulatory Commission Review of the 2017 Edition of ASME Section III, Division 5, ‘High Temperature Reactors’

To assist the Nuclear Regulatory Commission in its decision making on endorsement of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code Section III, Division 5 (2017 Edition) for development of advanced non-light water reactors, the following Division 5 portions were reviewed: Article HBB-2000 Material; Article HCB-2000 Material; Article HGB-2000 Material; Mandatory Appendix HBB-I-14 Tables and Figures; and, Nonmandatory Appendix HBB-U Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications. In addition to the 2017 Edition, the same parts of the 2019 Edition have also been reviewed as indicated in various sections of the report. This review was conducted by a collaboration of national laboratory and private sector participants with significant industrial experience, including some heavy lifting and deep diving from Clarus Consulting, LLC., all intended to achieve an objective, independent, and practical perspective. The report provides recommendations, descriptions of the evaluation methods, and the source references for the data used. To build confidence required for endorsement of the Code, this review was conducted as a verification and validation of the above Code contents. The objective of verification is to ensure that the Code is free of error – direct or implied; contains the information needed for its use, including proper coverage of the Code-specified materials for the intended application, and completeness and adequacy of references to other portions of the Code. The objective of validation is to authenticate that the Code tabulations and graphs represent design inputs consistent with what are determined using rules and methods specified by the Code. The authentication process used data that were assembled and/or generated independent of Code development, while the methods of analysis followed Code-specified methods where appropriate. The designated portions for this review cover the five alloys codified for high temperature reactor applications in Division 5, i.e. 316 SS, 304 SS, 800H, 2¼Cr-1Mo, and 9Cr-1Mo-V, regarding their general requirements, permitted specifications and design stress intensity values for pressure-retaining applications, deterioration in service, fatigue acceptance test, permissible weld materials, tensile and yield strength, expected minimum stress-to-rupture values (including for Alloy 718), weld stress rupture factors, permissible materials for bolting use, and restricted specifications in certain service applications. Additionally, stress intensity values for bolting materials including 316 SS, 304 SS and alloy 718 were reviewed. Analysis and discussion are also provided on contents outside of these designated Code portions where it was deemed relevant and necessary to develop a technically sound understanding of issues relating to the designated portions. Due to unavailability of sufficient test data on welds during the review period, the weld stress rupture factors in Tables HBB-I-10.14A to E, which cover a total of ten tables for the five alloys welded with twenty-eight different weld metals (some with similar properties), have been deferred to a future review effort. The review identified mainly two types of issues. The first type includes instances where the Code is found factually incomplete or incorrect, such as obsolete materials specifications listings, missing tabulation of stresses for bolting. Changes to the Code are recommended in these cases. The second type of issue includes instances where the Code tabulations and graphs are found to be less conservative than the review analysis results. In these cases, recommendations are made for further review and consideration where the difference in conservatism exceeds 10%, which is our threshold for questioning technical adequacy, meriting a risk assessment by the Nuclear Regulatory Commission and/or reactor designers. It is noted that this effort has been executed using all available data and established methods of analysis, including methods and criteria specified and used by the Code. As such, the findings that are presented in quantitative detail, in a format for convenient comparison with the Code, and with identification of where further review is recommended, should provide a sound technical basis for decisions about quantifying the implications of the reduced design margins and technical adequacy/inadequacy to form a basis for conditioning specific Code tabulation values on endorsement. Recommendations for specific changes to the Code, however, entail design conservatism considerations beyond the scope of this review effort, and are not made in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Synthesis and Observation of Emergent Phenomena in Epitaxial Heusler Compound Heterostructures

The proposal was on the synthesis and observation of emergent phenomena in epitaxial Heusler compound heterostructures. The large range of properties and number of Heusler compounds opens up a wide number of potential compounds that will exhibit emergent phenomena. The similarity, large range of relatively inexpensive, large area, high crystal quality, III-V bulk substrates, lattice parameters and the ability to tune the lattice parameters through ternary or quaternary III-V compound semiconductor epitaxial growth, makes III-V semiconductors an ideal choice for substrates for epitaxial growth of Heusler compounds. A number of half Heusler compounds have been predicted to exhibit band inversion, making them topological and are therefore expected to exhibit spin-momentum locked topological surface states with linear dispersion. Others are predicted to be semimetals with Weyl points and others semiconducting and magnetic. During the course of this grant, emphasis has been on investigating Heusler compounds with emergent phenomena and demonstrating the ability to tune their properties through alloying and strain. We have grown toplogical semimetal (PtLuSb, PtMnBi), Weyl (Co 2 MnAl, Co 2 TiGe), half metal (PtMnSb, Co 2 MnSi, Co 2 MnAl x Si 1-x , Co2FeAl), and semiconducting (CoTiSb, NiTiSn) and tuned their properties through alloying and epitaxial strain. We also investigated the closely related materials of rare-earth monopnictide, some of which have also been predicted to be topological. During the attempts to grow the PtMnBi, it was discovered that Bi, another predicted topological material when ultrathin, could be grown epitaxially on InSb, results for which are also reported here. The main focus for this effort has been on using variable photon energy and spin-dependent angle resolved photoemission (ARPES) to determine bulk band structure and surface states of pristine epitaxial films grown on III-V semiconductor and MgO substrates and correlate results with theory and transport measurements. Theory has been critical to interpretation of experimental results and has been essential in guiding experiments. The research benefited from several strong collaborations between the PIs and the beamline scientists at the Advanced Light Source at Lawrence Berkeley Laboratory, the Stanford Linear Accelerator Center (SLAC) at Stanford and at the Max Lab at Lund University in Sweden. The strong experiment - theory collaboration between the PI’s groups, the Palmstrøm group at UCSB and the Janotti group at the University of Delaware, has been critical for interpreting the experimental ARPES and magnetotransport measurements results and making predictions to guide experiments. Weekly interactive Zoom meetings made this work well. A collaboration between the Palmstrøm group and Dr. Alexei Fedorov at the Advanced Light Source (ALS) resulted in significant modifications to his end chamber to accommodate the vacuum suitcase that was designed and constructed in the Palmstrøm group at UCSB. In collaboration with beamline scientists, Drs. Makoto Hashimoto and Donghui Lu at SLAC, Palmstrøm made modifications to the vacuum suitcase and developed special sample holders that allowed samples to be grown in the Palmstrøm MBE systems at UCSB and transported in the UHV vacuum suitcase to SLAC for ARPES measurements. The development of the vacuum suitcase was essential for this grant as it has allowed variable photon energies to be used to identify surface versus bulk states on samples that could not be capped and decapped using As- or Sb-capping layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗