Search NASA⌕ Search

SEARCH · Search NASA

Results for “antenna arraying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Optical technology for spacecraft antennas

The issues involved in the design and implementation of high-speed fiberoptic distribution networks for spacecraft antennas are examined. The phased array antennas and antenna remoting are considered. The system requirements for these two generic system types are summarized, and their architectures are described. Optical beamforming of phased arrays is discussed, including beam control at the T/R module level, optical beam control on the fiber optic distribution network, and optical beamforming in free space.

Herczfeld, P. R.↗
NASA NTRS2005

System concepts for transmit arrays of parabolic antennas for deep space uplinks

Phased arrays of parabolic antennas are a potentially lower-cost way to provide uplink transmission to distant spacecraft, compared to the 34-m and 70-m antennas now used by the NASA Deep Space Network. A large transmit array could provide very high EIRP when needed for spacecraft emergencies, such as the equivalent of 1 MW radiated from a 70-m antenna. Cost-effectiveness is realized by dividing the array into smaller arrays to provide routine support to many spacecraft simultaneously. The antennas might be as small as 12-m in diameter, with as many as 100 antennas covering an area of 0.5 km to 1 km in extent. Such arrays present significant technical challenges in phase alignment, which must be maintained at close to 1 mm. The concept requires a very stable system with accurately known antenna phase center locations. The system is first calibrated by transmitting from all antennas, and observing the signals at a target located in the far fields of the individual antennas. The antennas are then pointed to the operational targets, with the signal phases and time delays set to reinforce in the target directions. This requires accurate knowledge of the target directions and calculation of the required phases. The system must be phase-stable for all directions and over the time between calibrations, which is desired to be at least one day. In this paper, a system concept is presented, the major error sources are identified, a rough error budget is established, and key elements of the system are discussed. A calibration method is recommended which uses satellites as radar targets. The performance goal is to achieve a combining loss of less than 0.2 dB in good weather, and of less than 1 dB in all but extremely bad weather.

Effective Isotropic Radiated Power (EIRP)↗
NASA NTRS1986

Features and technologies of ERS-1 (ESA) and X-SAR antennas

Features and technologies of planar waveguide array antennas developed for spaceborne microwave sensors are described. Such antennas are made from carbon fiber reinforced plastic (CFRP) employing special manufacturing and metallization techniques to achieve satisfactory electrical properties. Mechanical design enables deployable antenna structures necessary for satellite applications (e.g., ESA ERS-1). The slotted waveguide concept provides high aperture efficiency, good beamshaping capabilities, and low losses. These CFRP waveguide antennas feature low mass, high accuracy and stiffness, and can be operated within wide temperature ranges.

Schuessler, R.↗
NASA NTRS1987

An experimental investigation of parasitic microstrip arrays

The characteristics of a parasitic microstrip antenna array with a center-fed patch are experimentally investigated. The parasitic array is composed of identical parasitic patches which are symmetrically arranged and electromagnetically coupled to a center-fed patch. The shape and dimensions of the parasitic patches and their positions relative to the center-fed patch are parameters in the study. To show mutual coupling effects between radiating and nonradiating edges of adjacent patches, the impedance and radiation characteristics of a three-element parasitic array excited with (0.1) mode are examined, and compared to that of a single patch. Experimental data indicate that the presence of parasitic patches has significant effects upon the gain, resonant frequency, and impedance bandwidth of the array.

Lee, Richard Q.↗
NASA NTRS1972

Project Cyclops: a Design Study of a System for Detecting Extraterrestrial Intelligent Life

The requirements in hardware, manpower, time and funding to conduct a realistic effort aimed at detecting the existence of extraterrestrial intelligent life are examined. The methods used are limited to present or near term future state-of-the-art techniques. Subjects discussed include: (1) possible methods of contact, (2) communication by electromagnetic waves, (3) antenna array and system facilities, (4) antenna elements, (5) signal processing, (6) search strategy, and (7) radio and radar astronomy.

Source record↗
NASA NTRS1981

A multiple access communication network based on adaptive arrays

A single frequency communication system is considered consisting of K possibly moving users distributed in space simultaneously communicating with a central station equipped with a computationally adapted array of n = or K antennas. Such a configuration could result if K spacecraft were to be simultaneously tracked by a single DSN complex consisting of an n antennas array. The array employs K sets of n weights to segregate the signals received from the K users. The weights are determined by direct computation based on known position information of the K users. Currently known techniques require (for n = K) about (4/3)K to the 4th power computer operations (multiply and add) to perform such computations. A technique that accomplishes this same goal in 8 K to the 3rd power operations, yielding a reduction by a factor K/6, was developed.

Zohar, S.↗
NASA NTRS1981

Frequency and timing system for the consolidated DSN and STDN tracking network

The consolidation on the existing Deep Space Network (DSN) and colocated Goddard Spaceflight Tracking and Data Network (STDN) stations into a multiple antenna array is discussed. Each site includes a signal processing center (SPC) centered in an array of four or five antennas each located within approximately 300 to 800 meters of the SPC. A central frequency and timing system (FTS) located in the SPC contains reference frequency, timing and time code generation, and distribution equipment for both the SPC and each antenna with its associated front end antenna control building. The reference frequency distribution and clock equipment are driven by a hydrogen maser as the prime frequency standard with cesium beam frequency standard as the secondary.

Coffin, R. C.↗
NASA NTRS1966

ATS-4 study program, volume 2 Final report

Systems analysis of Applications Technology Satellite-4 - mission and power profiles, antenna array accuracy and efficiency, failure modes, and weight summaries

ANTENNA ARRAY↗
NASA NTRS2009

UAVSAR Phased Array Aperture

This paper describes the development of a patch antenna array for an L-band repeat-pass interferometric synthetic aperture radar (InSAR) instrument that is to be flown on an unmanned aerial vehicle (UAV). The antenna operates at a center frequency of 1.2575 GHz and with a bandwidth of 80 MHz, consistent with a number of radar instruments that JPL has previously flown. The antenna is designed to radiate orthogonal linear polarizations in order to facilitate fully-polarimetric measurements. Beam-pointing requirements for repeat-pass SAR interferometry necessitate electronic scanning in azimuth over a range of -20degrees in order to compensate for aircraft yaw. Beam-steering is accomplished by transmit/receive (T/R) modules and a beamforming network implemented in a stripline circuit board. This paper, while providing an overview of phased array architecture, focuses on the electromagnetic design of the antenna tiles and associated interconnects. An important aspect of the design of this antenna is that it has an amplitude taper of 10dB in the elevation direction. This is to reduce multipath reflections from the wing that would otherwise be detrimental to interferometric radar measurements. This taper is provided by coupling networks in the interconnect circuits as opposed to attenuating the output of the T/R modules. Details are given of material choices and fabrication techniques that meet the demanding environmental conditions that the antenna must operate in. Predicted array performance is reported in terms of co-polarized and crosspolarized far-field antenna patterns, and also in terms of active reflection coefficient.

Unmanned Aerial Vehicle (UAV)↗
NASA NTRSDate not supplied

Towards Gbps Downlinks from Low-Cost Active Phased Arrays

Spacecraft performing science missions use high-directivity antennas to quickly downlink large amounts of collected data. Movement required to keep gimbaled reflector antennas trained on target receivers can impart blockages or vibrations which perturb precision science instruments. Recent manufacturing advances have made Ka-band electronically-steered antenna arrays a cost-effective option to mitigate these challenges, but only if these devices can be proven to deliver comparable quality of service. In this work we present a hardware and software architecture for high-rate links using an active phased array-based terminal in a 1U (10cm cube) form factor. Over-the-air tests in an antenna range characterize two key features of the architecture: high-order (32APSK and above) modulations and dual carriers. We calculate an optimal modulation-dependent input power backoff from array saturation and perform orbital simulations of the link at this operating point. We conclude that reliable links with rates in excess of 1Gbps are possible with current-generation hardware.

Adam Gannon↗
NASA NTRSDate not supplied

Design of a Thermal Testbed for Metrology of Active Antennas

NASA mission requirements have driven an increased interest in active phased array antennas (APAA) for space-based user communication terminals. Recent advancements in 5G technology have driven down the cost of APAA development and manufacturing all while providing a technology solution that covers many existing Ka-Band satellite communication spectrum bands. While these developments have provided ample opportunities to leverage new chips and arrays for use in space, there is also a need to evaluate these antennas in a relevant environment. Active arrays, as designed for use in 5G, require thermal management to avoid damage to the device as well as to maintain performance. Measured performance under various thermal conditions is essential both for understanding overall APAA performance and ensuring operation is within required tolerances. To address these measurement needs, the SmallSat Ka-band Operations User Terminal (SKOUT) project at the NASA Glenn Research Center (GRC) developed a test environment that combines traditional antenna and communication system metrology with a conduction cooling/heating thermal control system to simulate the space thermal environment. This paper will address the metrologysystem design and performance specifications as well as test article setup and operation. Tests that are typically performed at ambient temperature can now be performed over the typical temperature range of a Low Earth Orbit (LEO) mission. These tests include error vector magnitude (EVM), gain to noise temperature (G/T), antenna patterns, and non-linear characterization. The paper will cover the configuration for each test and provide results from a recent test campaign. Results illustrate the importance of higher fidelity environmental testing when evaluating the performance of an APAA.

active phased array↗
NASA NTRS1975

System consideration, design approach and test of a low gain spherical coverage antenna for large space vehicles

A fixed beam array antenna approach is proposed to meet the omnidirectional receiving and transmitting requirements of LST (Large Space Telescope). The proposed method uses an antenna of known performance and scales the size and frequency to conform with the LST 1/5-th scale model. The simplification that the approach provides over switching antenna elements on board the LST or switching from the ground by frequency diversity makes it worthy of consideration against the factors of performance, cost, reliability, and operations complexity. For LST applications, the system capabilities, requirements, and margins are summarized. The areas to be covered by further investigations into the proposed LST antenna are noted.

Ferguson, R. E.↗
NASA NTRS1981

Virtual center arraying

Methods to increase the amount of data that can be received from outer planet missions are described with emphasis on antenna arraying systems designed to increase the total effective aperture of the receiving system. One such method is virtual center arraying (VCA). In VCA, a combined carrier reference is derived at a point that is, conceptually, the geometric center of the array. This point need not coincide with any of the actual antennas of the array. A noise analysis of the VCA system is given along with formulas for the phase jitter as a function of loop bandwidths and the amount of loop damping. If the ratio of the loop bandwidths of the center loop to the vertex loops is greater than 100, then the jitter is very nearly equal to that expected for ideal combined carrier referencing.

Deutsch, L. J.↗