Results for “augmentation systems” — Page 25

NASA NTRS1984

Video compression using conditional replenishment and motion prediction

A study of a low-rate monochrome video compression system is presentd in this paper. This system is a conditional-replenishment coder that uses two-dimensional Walsh-transform coding within each video frame. The conditional-replenishment algorithm works by transmitting only the portions of an image that are changing in time. This system is augmented with a motn-prediction algorithm that measures spatial dispalcement parameters from frame to frame, and codes the data using these parameters. A comparison is made between the conditional-replenishment system with, and without, the motion-predictinalgorthm. Subsampling in time is ued to maintain the data rate rate at a fixed value. Average bit rates of 1 bit/picture element (pel) to 1/16 bit/pel are considered. The resultant performance of the compression simulations is presented in terms of the average frame rates produced.

Hein, D. N.↗

NASA NTRS1974

Variable geometry for supersonic mixed-compression inlets

Study of two-dimensional and axisymmetric supersonic mixed-compression inlet systems has shown that the geometry of both systems can be varied to provide adequate transonic airflow to satisfy the airflow demand of most jet engines. Collapsing geometry systems for both types of inlet systems provide a generous amount of transonic airflow for any design Mach number inlet system. However, the mechanical practicality of collapsing centerbodies for axisymmetric inlet systems is doubtful. Therefore, translating centerbody axisymmetric inlets with auxiliary airflow systems to augment the transonic airflow capability are an attractive alternative. Estimates show that the capture mass-flow ratio at Mach number 1.0 can be increased approximately 0.20 for a very short axisymmetric inlet system designed for Mach number 2.37. With this increase in mass-flow ratio, even variable-cycle engine transonic airflow demand can be matched without oversizing the inlet at the design Mach number.

Sorensen, N. E.↗

NASA NTRS1987

Large space antennas: A systems analysis case history

The value of systems analysis and engineering is aptly demonstrated by the work on Large Space Antennas (LSA) by the NASA Langley Spacecraft Analysis Branch. This work was accomplished over the last half-decade by augmenting traditional system engineering, analysis, and design techniques with computer-aided engineering (CAE) techniques using the Langley-developed Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) system. This report chronicles the research highlights and special systems analyses that focused the LSA work on deployable truss antennas. It notes developmental trends toward greater use of CAE techniques in their design and analysis. A look to the future envisions the application of improved systems analysis capabilities to advanced space systems such as an advanced space station or to lunar and Martian missions and human habitats.

Keafer, Lloyd S.↗

NASA NTRS1982

An experiment to enable commercial mobile satellite service

A Mobile Satellite Experiment (MSAT-X) is described, based on a planned cooperative U.S./Canadian program. The experiment would establish network architecture, develop system and ground-segment technology, and define the technical characteristics needed to help structure the regulatory/institutional framework needed to enable a first-generation commercial satellite service. A satellite of this type would augment terrestrial systems, both cellular and noncellular, in the thin-route/rural areas of the country where service is either unavailable or inadequate. Applications range from wide-area radio/dispatch (e.g., oil exploration and interstate trucking) to extension of the public mobile telephone service. Market estimates are provided and experiment objectives and requirements are delineated. The requirements are being developed in close coordination with the Department of Communications (DOC) of Canada and with industry and potential-user organizations. The paper closes with a development plan and milestone chart.

Lovell, R. R.↗

NASA NTRS1980

Dish Stirling solar receiver program

A technology demonstration of a Dish Stirling solar thermal electric system can be accomplished earlier and at a much lower cost than previous planning had indicated by employing technical solutions that allow already existing hardware, with minimum modifications, to be integrated into a total system with a minimum of development. The DSSR operates with a modified United Stirling p-40 engine/alternator and the JPL Test Bed Concentrator as a completely integrated solar thermal electric system having a design output of 25 kWe. The system is augmented by fossil fuel combustion which ensures a continuous electrical output under all environmental conditions. Technical and economic studies by government and industry in the United States and abroad identify the Dish Stirling solar electric system as the most appropriate, efficient and economical method for conversion of solar energy to electricity in applications when the electrical demand is 10 MWe and less.

Haglund, R. A.↗

NASA NTRS1974

Cybernetic anthropomorphic machine systems

Functional descriptions are provided for a number of cybernetic man machine systems that augment the capacity of normal human beings in the areas of strength, reach or physical size, and environmental interaction, and that are also applicable to aiding the neurologically handicapped. Teleoperators, computer control, exoskeletal devices, quadruped vehicles, space maintenance systems, and communications equipment are considered.

Gray, W. E.↗

NASA NTRSDate not supplied

Interoperable Services to Mitigate Lunar Position, Navigation, and Timing Challenges

Across the Earth, both civilian and government endeavors enjoy a built-in reliance on a position, navigation, and timing (PNT) infrastructure to which they are largely blind. Whether walking, driving, flying, or orbiting, Earth-centric PNT systems that have evolved over decades provide a core functionality to which we have grown accustomed for these pursuits. As NASA joins with other government space agencies and commercial partners to return humans to the Moon in a sustained manner within the current decade, expectations for PNT knowledge and timeliness at the Moon rival those on Earth. The need exists to develop a viable lunar-centric PNT infrastructure to support the planned human and robotic exploits. Navigating within the influence of the Moon presents its own set of challenges. Identification, understanding, and use of a unified reference frame and time system on which navigation is based becomes a fundamental need at the Moon. In addition to the unified foundational elements, measurement liability, dynamic conditions that require Earth-independent autonomous operations, and standards for PNT signals and message-based data exchange each represent distinct challenges to navigation in a burgeoning operational lunar environment. The PNT services planned as part of the lunar communications and navigation relay architecture known as LunaNet aid in surmounting the challenges. LunaNet interoperability specifications stipulate standards for signal parameters, messages, and lunar reference systems for PNT services. Within LunaNet’s defined interoperability resides the concept of a Reference Signal to provide communication signals specifically structured to enable measurement of pseudorange, Doppler, and time transfer by the recipient. One such signal type, the Augmented Forward Signal (AFS), functions as the mainstay for LunaNet PNT, while also serving the data needs for ubiquitous broadcast of network access and rapid unscheduled dissemination of alerts and messages. The presence of a geometrically distributed network of orbiting nodes transmitting the AFS forms the basis for the Lunar Augmented Navigation System (LANS), that delivers both radio navigation and data to multiple users in the lunar environment simultaneously. After reviewing the challenges associated with lunar navigation, this paper will describe the concepts and rationale behind the LunaNet PNT services. By borrowing techniques from Earth-centric Global Navigation Satellite Services (GNSS), the Tracking and Data Relay Satellite System, and the Consultative Committee for Space Data Standards, PNT from LunaNet aids to overcome challenges faced for accurate lunar navigation.

LunaNet↗

NASA NTRSDate not supplied

Interoperable Services to Mitigate Lunar Position, Navigation, and Timing Challenges

Across the Earth, both civilian and government endeavors enjoy a built-in reliance on a position, navigation, and timing (PNT) infrastructure to which they are largely blind. Whether walking, driving, flying, or orbiting, Earth-centric PNT systems that have evolved over decades provide a core functionality to which we have grown accustomed for these pursuits. As NASA joins with other government space agencies and commercial partners to return humans to the Moon in a sustained manner within the current decade, expectations for PNT knowledge and timeliness at the Moon rival those on Earth. The need exists to develop a viable lunar-centric PNT infrastructure to support the planned human and robotic exploits. Navigating within the influence of the Moon presents its own set of challenges. Identification, understanding, and use of a unified reference frame and time system on which navigation is based becomes a fundamental need at the Moon. In addition to the unified foundational elements, measurement liability, dynamic conditions that require Earth-independent autonomous operations, and standards for PNT signals and message-based data exchange each represent distinct challenges to navigation in a burgeoning operational lunar environment. The PNT services planned as part of the lunar communications and navigation relay architecture known as LunaNet aid in surmounting the challenges. LunaNet interoperability specifications stipulate standards for signal parameters, messages, and lunar reference systems for PNT services. Within LunaNet’s defined interoperability resides the concept of a Reference Signal to provide communication signals specifically structured to enable measurement of pseudorange, Doppler, and time transfer by the recipient. One such signal type, the Augmented Forward Signal (AFS), functions as the mainstay for LunaNet PNT, while also serving the data needs for ubiquitous broadcast of network access and rapid unscheduled dissemination of alerts and messages. The presence of a geometrically distributed network of orbiting nodes transmitting the AFS forms the basis for the Lunar Augmented Navigation System (LANS), that delivers both radio navigation and data to multiple users in the lunar environment simultaneously. After reviewing the challenges associated with lunar navigation, this paper will describe the concepts and rationale behind the LunaNet PNT services. By borrowing techniques from Earth-centric Global Navigation Satellite Services (GNSS), the Tracking and Data Relay Satellite System, and the Consultative Committee for Space Data Standards, PNT from LunaNet aids to overcome challenges faced for accurate lunar navigation.

Navigation↗

NASA NTRS1981

Design of a V/STOL propulsion system for a large-scale fighter model

Modifications were made to the existing Large-Scale STOL fighter model to simulate a V/STOL configuration. Modifications include the substitutions of two dimensional lift/cruise exhaust nozzles in the nacelles, and the addition of a third J97 engine in the fuselage to suppy a remote exhaust nozzle simulating a Remote Augmented Lift System. A preliminary design of the inlet and exhaust ducting for the third engine was developed and a detailed design was completed of the hot exhaust ducting and remote nozzle.

Willis, W. S.↗

NASA NTRS1988

A study of helicopter stability and control including blade dynamics

A linearized model of rotorcraft dynamics has been developed through the use of symbolic automatic equation generating techniques. The dynamic model has been formulated in a unique way such that it can be used to analyze a variety of rotor/body coupling problems including a rotor mounted on a flexible shaft with a number of modes as well as free-flight stability and control characteristics. Direct comparison of the time response to longitudinal, lateral and directional control inputs at various trim conditions shows that the linear model yields good to very good correlation with flight test. In particular it is shown that a dynamic inflow model is essential to obtain good time response correlation, especially for the hover trim condition. It also is shown that the main rotor wake interaction with the tail rotor and fixed tail surfaces is a significant contributor to the response at translational flight trim conditions. A relatively simple model for the downwash and sidewash at the tail surfaces based on flat vortex wake theory is shown to produce good agreement. Then, the influence of rotor flap and lag dynamics on automatic control systems feedback gain limitations is investigated with the model. It is shown that the blade dynamics, especially lagging dynamics, can severly limit the useable values of the feedback gain for simple feedback control and that multivariable optimal control theory is a powerful tool to design high gain augmentation control system. The frequency-shaped optimal control design can offer much better flight dynamic characteristics and a stable margin for the feedback system without need to model the lagging dynamics.

Zhao, Xin↗

NASA NTRS2009

Analysis of Aeroheating Augmentation due to Reaction Control System Jets on Orion Crew Exploration Vehicle

The analysis of effects of the reaction control system jet plumes on aftbody heating of Orion entry capsule is presented. The analysis covered hypersonic continuum part of the entry trajectory. Aerothermal environments at flight conditions were evaluated using Langley Aerothermal Upwind Relaxation Algorithm (LAURA) code and Data Parallel Line Relaxation (DPLR) algorithm code. Results show a marked augmentation of aftbody heating due to roll, yaw and aft pitch thrusters. No significant augmentation is expected due to forward pitch thrusters. Of the conditions surveyed the maximum heat rate on the aftshell is expected when firing a pair of roll thrusters at a maximum deceleration condition.

Dyakonov, Artem A.↗

NASA NTRS1996

Simulation model of the F/A-18 high angle-of-attack research vehicle utilized for the design of advanced control laws

The 'f18harv' six degree-of-freedom nonlinear batch simulation used to support research in advanced control laws and flight dynamics issues as part of NASA's High Alpha Technology Program is described in this report. This simulation models an F/A-18 airplane modified to incorporate a multi-axis thrust-vectoring system for augmented pitch and yaw control power and actuated forebody strakes for enhanced aerodynamic yaw control power. The modified configuration is known as the High Alpha Research Vehicle (HARV). The 'f18harv' simulation was an outgrowth of the 'f18bas' simulation which modeled the basic F/A-18 with a preliminary version of a thrust-vectoring system designed for the HARV. The preliminary version consisted of two thrust-vectoring vanes per engine nozzle compared with the three vanes per engine actually employed on the F/A-18 HARV. The modeled flight envelope is extensive in that the aerodynamic database covers an angle-of-attack range of -10 degrees to +90 degrees, sideslip range of -20 degrees to +20 degrees, a Mach Number range between 0.0 and 2.0, and an altitude range between 0 and 60,000 feet.

Strickland, Mark E.↗

NASA NTRS1985

Expert systems and their use in augmenting design optimization

The challenging requirements that are evolving for future aircraft demand that each design be optimally integrated, for the penalties imposed by nonoptimal performance are significant. Classic numerical optimization algorithms have been and will continue to be important tools for aircraft designers. These methods are, however, limited to certain categories of aircraft design variables, leaving the remainder to be determined by the user. A method that makes use of knowledge-based expert systems offers the potential for aiding the conceptual design process in a way that is similar to that of numerical optimization, except that it would address discrete, discontinuous, abstract, or any other unoptimized aspect of vehicle design and integration. Other unique capabilities such as automatic discovery and learning in design may also be achievable in the near term. This paper discusses current practice in conceptual aircraft design and knowledge-based systems, and how knowledge-based systems can be used in conceptual design.

Kidwell, G. H.↗

NASA NTRS2018

Feedback Control of Flight Speed to Reduce Unmanned Aerial System Noise

The aim of this initial study is to incorporate an acoustic metric into the flight control system of an unmanned aerial vehicle. This could be used to mitigate the noise impact of unmanned aerial systems operating near residential communities. To incorporate an acoustic metric into a pre-existing flight control system, two things are required: a source noise model, and an acoustic controller. An acoustic model was developed based on Gutin's work to estimate propeller noise. The flight control system was augmented with a controller to reduce propeller noise using feedback control of the commanded flight speed until an acoustic target was met. This control approach focuses on modifying flight speed only, with no perturbation to the trajectory. Multiple flight simulations were performed and the results showed that integrating an acoustic metric into the flight control system of an unmanned aerial system is possible.

Matthew B Galles↗

NASA NTRS2005

Reactions of Air Transport Flight Crews to Displays of Weather During Simulated Flight

Display of information in the cockpit has long been a challenge for aircraft designers. Given the limited space in which to present information, designers have had to be extremely selective about the types and amount of flight related information to present to pilots. The general goal of cockpit display design and implementation is to ensure that displays present information that is timely, useful, and helpful. This suggests that displays should facilitate the management of perceived workload, and should allow maximal situation awareness. The formatting of current and projected weather displays represents a unique challenge. As technologies have been developed to increase the variety and capabilities of weather information available to flight crews, factors such as conflicting weather representations and increased decision importance have increased the likelihood for errors. However, if formatted optimally, it is possible that next generation weather displays could allow for clearer indications of weather trends such as developing or decaying weather patterns. Important issues to address include the integration of weather information sources, flight crew trust of displayed weather information, and the teamed reactivity of flight crews to displays of weather. Past studies of weather display reactivity and formatting have not adequately addressed these issues; in part because experimental stimuli have not approximated the complexity of modern weather displays, and in part because they have not used realistic experimental tasks or participants. The goal of the research reported here was to investigate the influence of onboard and NEXRAD agreement, range to the simulated potential weather event, and the pilot flying on flight crew deviation decisions, perceived workload, and perceived situation awareness. Fifteen pilot-copilot teams were required to fly a simulated route while reacting to weather events presented in two graphical formats on a separate visual display. Measures of flight crew reactions included performance-based measures such as deviation decision accuracy, and judgment-based measures such as perceived decision confidence, workload, situation awareness, and display trust. Results demonstrated that pilots adopted a conservative reaction strategy, often choosing to deviate from weather rather than ride through it. When onboard and NEXRAD displays did not agree, flight crews reacted in a complex manner, trusting the onboard system more but using the NEXRAD system to augment their situation awareness. Distance to weather reduced situation awareness and heightened workload levels. Overall, flight crews tended to adopt a participative leadership style marked by open communication. These results suggest that future weather displays should exploit the existing benefits of NEXRAD presentation for situation awareness while retaining the display structure and logic inherent in the onboard system.

Bliss, James P.↗

NASA NTRS1982

A remote augmentor lift system with a turbine bypass engine

Two supersonic vertical takeoff or landing (VTOL) aircraft engine types, a conventional medium bypass ratio turbofan, and a turbine bypass turbojet were studied. The aircraft assumed was a clipped delta wing with canard configuration. A VTOL deck launched intercept, DLI, mission with Mach 1.6 dash and cruise segments was used as the design mission. Several alternate missions requiring extended subsonic capabilities were analyzed. Comparisons were made between the turbofan (TF) and the turbine bypass turbojet (TBE) engines in airplane types using a Remote Augmented Lift Systems, RALS and a Lift plus Lift Cruise system (L+LC). The figure of merit was takeoff gross weight for the VTOL DLI mission. The results of the study show that the turbine bypass turbojet and the conventional turbofan are competitive engines for both type of aircraft in terms of takeoff gross weight and range. However, the turbine bypass turbojet would be a simpler engine and may result in more attractive life cycle costs and reduced maintenance. The RALS and L+LC airplane types with either TBE or TF engines have approximately the same aircraft takeoff gross weight.

Fishbach, L. H.↗

NASA NTRS1997

HARV ANSER Flight Test Data Retrieval and Processing Procedures

Under the NASA High-Alpha Technology Program the High Alpha Research Vehicle (HARV) was used to conduct flight tests of advanced control effectors, advanced control laws, and high-alpha design guidelines for future super-maneuverable fighters. The High-Alpha Research Vehicle is a pre-production F/A-18 airplane modified with a multi-axis thrust-vectoring system for augmented pitch and yaw control power and Actuated Nose Strakes for Enhanced Rolling (ANSER) to augment body-axis yaw control power. Flight testing at the Dryden Flight Research Center (DFRC) began in July 1995 and continued until May 1996. Flight data will be utilized to evaluate control law performance and aircraft dynamics, determine aircraft control and stability derivatives using parameter identification techniques, and validate design guidelines. To accomplish these purposes, essential flight data parameters were retrieved from the DFRC data system and stored on the Dynamics and Control Branch (DCB) computer complex at Langley. This report describes the multi-step task used to retrieve and process this data and documents the results of these tasks. Documentation includes software listings, flight information, maneuver information, time intervals for which data were retrieved, lists of data parameters and definitions, and example data plots.

Yeager, Jessie C.↗

NASA NTRS1983

An evaluation of Landsat data for input to a state geographic information system

The results of a study to evaluate Landsat digital data, categorized by land cover, for input to the Maryland Automated Geographic Information (MAGI) system, the state georeferenced data base, are presented. Good correspondence is found between the MAGI system and Landsat data for six of seven categories: forest, water, crop/pasture, medium-density residential, low-density residential, and transitional (disturbed land, construction). Discrepancies between the results are found for commercial/industrial/institutional areas which are due to differences in interpretative methodologies, not to deficiencies in either data source. It is concluded that Landsat data are suitable for future Maryland land cover inventories, and can also be used to augment MAGI system data.

Middleton, E. M.↗