SEARCH · Search NASA

Results for “boundary layer height”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1986

The structure of the atmospheric boundary layer in the central equatorial Pacific during January and February of FGGE

The structure of the atmospheric boundary layer for a region between Hawaii and the equator is studied using dropwindsonde data (about 900 soundings) collected in January and February 1979 as part of the First GARP Global Experiment. These data were used to establish the longitudinal and latitudinal variations in the thermodynamic and wind structure of the boundary layer and describe differences in the structure for convectively active and inactive conditions. Low-level inversions (at a pressure of approximately 850 mb) were found to be an important feature of the structure of the boundary layer for undisturbed conditions. Although the frequency of low-level inversions decreased equatorward from Hawaii, the average height of the inversions observed in these regions did not vary significantly in the north-south direction. For convectively undisturbed conditions, low-level inversions are on the average of sufficient strength to suppress deep convection. However, it is shown they could easily be modified by upward vertical motion to give a boundary layer structure similar to that observed in areas where deep convection was observed.

Firestone, James K.↗

NASA NTRS2005

Stagnation Flow in Thin Streamer Boundaries

Slow solar wind is believed to arise in the legs or near the cusp of streamers, inside the brightness boundary. In an earlier study, we used an analytic model of flow in this layer to analyze the effect of the magnetic field on the geometry of the flow. That study successfully described those conditions that can lead to a decrease of the flow speed with increasing height near the cusp of the closed magnetic helmet inside a streamer. The model was, however, restricted to a radial brightness boundary on the streamer and hence to a relatively thick outflow region near the cusp. Here this restriction is relaxed through the explicit introduction of a coronal hole-like region outside the brightness boundary. We use the model to describe flow solutions for outflow in a thin layer inside the brightness boundary. The flow geometry now can be constrictive just above the cusp, and we show solutions of this type. Many solutions then show a diverging geometry at greater heights above the cusp, out to at least 5 solar radius. We fail to find solutions in which the geometry alone leads to slow flow but give a more general description than before of conditions favoring slow flow and, consequently, gravitational settling in the legs of streamers.

Suess, Steven T.↗

NASA NTRS1982

NASA participation in the 1980 PEPE/NEROS project: Data archive

Eight experimental air quality measurement systems were investigated during July and August 1980 as part of the EPA PEPE/NEROS fiel measurement program. Data from those efforts have been entered into an archive that may be accessed by other researchers. The data sets consists of airborne measurements of regional mixed layer heights and aerosol and ozone distributions as well as point measurements of meteorological parameters and ozone obtained during diurnal transitions in the planetary boundary layer. This report gives a discussion of each measurement system, a preliminary assessment of data quality, a description of the archive format for each data set, and a summary of several proposed scientific studies which will utilize these data.

Brewer, D. A.↗

DOE OSTI2024

On the Departure from Monin–Obukhov Surface Similarity and Transition to the Convective Mixed Layer

Large-eddy simulations are used to evaluate mean profile similarity in the convective boundary layer (CBL). Particular care is taken regarding the grid sensitivity of the profiles and the mitigation of inertial oscillations in the simulation spin-up. The nondimensional gradients Φ for wind speed and air temperature generally align with Monin–Obukhov similarity across cases but have a steeper slope than predicted within each profile. The same trend has been noted in several other recent studies. The Businger-Dyer relations are modified here with an exponential cutoff term to account for the decay in Φ to first-order approximation, yielding improved similarity from approximately 0.05z i to above 0.3z i , where z i is the CBL depth. The necessity for the exponential correction is attributed to an extended transition from surface scaling to zero gradient in the mixed layer, where the departure from Monin–Obukhov similarity may be negligible at the surface but becomes substantial well below the conventional surface layer height of 0.1 z i .

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2020

Combining MODIS LAI with ICESat-Based Canopy Heights Improves Spaceborne Estimates of Vegetation Roughness Length for Momentum

Most land-surface models require parameterization of vertical wind profiles within the atmospheric boundary layer. For vegetated surfaces, it is common to assume a logarithmic profile in the surface layer, which includes estimates of vegetation roughness length for momentum (z0) and zero-plane displacement height (d0). This study finds that remotely-sensed forest canopy heights improve estimates of aerodynamic roughness length for momentum using a previously-developed representation of the roughness sublayer (Raupach 1992; Jasinski et al. 2005). Resulting roughness products consist of two datasets: 1) 14 years of 8-day snapshots of the global land surface at a nominal spatial resolution of 500-meters for users who wish to retain full temporal resolution and interannual variability; and 2) multiyear averages of the 8-day snapshots, here referred to as "climatologies" of roughness, which retain underlying seasonality. Both products are suitable for use in data assimilation and reanalyses such as the National Climate Assessment Land Data Assimilation System (NCA-LDAS), for which these products were initially developed.

Borak, Jordan S.↗

DOE OSTI2024

California Offshore Wind Resource Bias Investigation and Correction [Slides]

This presentation highlights the findings of an investigation into the causes of high wind speed bias in offshore California's 20-year wind resource dataset, CA20, released by the National Renewable Energy Laboratory (NREL) in 2020. Utilizing observations from floating lidars deployed by the Pacific Northwest National Laboratory (PNNL), considerable bias in modeled hub-height winds was identified. The study reveals that the choice of planetary boundary layer (PBL) scheme significantly impacts wind speed accuracy, with the less common Yonsei University (YSU) scheme nearly eliminating bias compared to the widely used Mellor-Yamada-Nakanishi-Niino (MYNN) scheme. Furthermore, it shows that one of the key factors contributing to this modeled bias is the fact that MYNN overestimates the frequency of stable atmospheric conditions in offshore California. As a result, an updated dataset, NOW-23, incorporating YSU as the PBL scheme, has been produced.

17 WIND ENERGY↗

NASA NTRS1970

Effect of wall roughness on liquid oscillations damping in rectangular tanks

Tests were conducted in two rectangular glass tanks using silicon carbide grit bonded to walls to determine effect of wall roughness for damping liquid oscillations. Tests included effects of roughness height, roughness location, roughness at various values, amplitude decay, Reynolds number, and boundary layer thickness.

Bugg, F. M.↗

NASA NTRS1984

Turbulent roughness drag due to surface waviness at low roughness Reynolds numbers

The current investigation has the objective to provide data which will make it possible to obtain a better estimate regarding the roughness drag for surface waviness. The data employed for this investigation were acquired in connection with a wavy wall study which was conducted as part of an overall program to reduce the skin friction of turbulent boundary layers in external flows. The results of the present investigation show that the low-speed roughness drag of small-amplitude sinusoidal wave trains having wavelengths of the order of the boundary-layer thickness is not only a function of h/lambda (h = total wave height, lambda = wavelength), but, in addition, is also a function of the roughness Reynolds number.

Lin, J. C.↗

NASA NTRS1993

Thin Hot-Film Sensors On Polyimide Film

Array of closely spaced hot-film sensors with thickness well below critical reference height with regard to air-flow pattern nonintrusively detect laminar boundary-layer transitions with very high resolution. Method developed at NASA Langley Research Center to fabricate such sensors on polyimide films to detect boundary-layer transitions with resolution as high as 0.050 in. These films formed by combination of vacuum deposition and photolithography.

Hopson, Purnell↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Boundary layer transition↗

NASA NTRS2015

Reducing the Effect of Transducer Mount Induced Noise on Aeroacoustic Wind Tunnel Testing Data with a New Transducer Mount Design

Characterization of launch vehicle unsteady aerodynamics is a field best studied through experimentation, which is often carried out in the form of large scale wind tunnel testing. Measurement of the fluctuating pressures induced by the boundary layer noise is customarily made with miniature pressure transducers installed into a model of the vehicle of interest. Literature shows that noise level increases between two to five decibels (dB referenced to 20 micropascal) can be induced when the transducer surface is not mounted perfectly flush with the model outer surface. To reduce this artificially induced noise, special transducer holders have been used for aeroacoustic wind tunnel testing by NASA. This holder is a sleeve into which the transducer fits, with a cap that allows it to be mounted in a recessed hole in the model. A single hole in the holder allows the transport of the tunnel medium so the transducer can discriminate the fluctuating pressure due to the turbulent boundary layer noise. The holder is first dry fitted into the model and any difference in height between the holder and the model surface can be sanded flush. The holder is then removed from the model, the transducer glued inside the holder, and the holder replaced in the model, secured also with glue, thus eliminating the problem of noise level increases due to lack of flushness. In order to work with this holder design, special transducers have been ordered with their standard screen removed and the diaphragm moved as close to the top of the casing as possible to minimize any cavity volume. Although this greatly reduces induced noise due to the transducers being out of flush, the holders can also induce a cavity resonance that is usually at a very high frequency. This noise is termed transducer mount induced noise (XMIN). The peak of the mode can vary with the cavity depth, boundary layer noise that can excite the mode, tunnel flow medium, and the build of the transducers. Because the boundary layer flow interaction with the microphone holder seems to have some effect on the cavity resonance response, the NASA/Marshall Space Flight Center (MSFC) aeroacoustic team postulated that changing the design of the holder might reduce the cavity resonance response. An experiment was performed at the MSFC Trisonic Wind Tunnel comparing a new holder design with the traditional MSFC holder. The new holder design is intended to mimic the Kulite Semiconductors, Inc. B-screen, where the single hole of the traditional MSFC holder is replaced by a series of ten 0.007 inch diameter holes. This particular design serves to protect the transducer diaphragm as in the manufacturer's B-screen, but also increases the frequency of the XMIN such that it is not apparent in the data collected from aeroacoustic wind tunnel tests. MSFC compared the two holder designs by installing two transducers in standard holders on one side of a ten inch long ten degree cone, and two transducers in B-screen holders on the opposite side for a series of runs at different conditions. Over 11-13 February, 2013, the model was run at Mach numbers between 0.80 and 1.96 at angles of attack at 0 deg, plus or minus 1 deg, plus or minus 2 deg, plus or minus 4 deg, and plus or minus 8 deg. Model roll attitudes at 0 deg, 90 deg, and 180 deg were tested to isolate potential tunnel bias. This paper presents results from the test showing that the proposed holder design significantly reduces the influence of XMIN on measured fluctuating pressure levels.

Herron, A. J.↗

NASA NTRS2001

Measurements of Aerosol Vertical Profiles and Optical Properties during INDOEX 1999 Using Micro-Pulse Lidars

Micro-pulse lidar systems (MPL) were used to measure aerosol properties during the Indian Ocean Experiment (INDOEX) 1999 field phase. Measurements were made from two platforms: the NOAA ship RN Ronald H. Brown, and the Kaashidhoo Climate Observatory (KCO) in the Maldives. Sunphotometers were used to provide aerosol optical depths (AOD) needed to calibrate the MPL. This study focuses on the height distribution and optical properties (at 523 nm) of aerosols observed during the campaign. The height of the highest aerosols (top height) was calculated and found to be below 4 km for most of the cruise. The marine boundary layer (MBL) top was calculated and found to be less than 1 km. MPL results were combined with air mass trajectories, radiosonde profiles of temperature and humidity, and aerosol concentration and optical measurements. Humidity varied from approximately 80% near the surface to 50% near the top height during the entire cruise. The average value and standard deviation of aerosol optical parameters were determined for characteristic air mass regimes. Marine aerosols in the absence of any continental influence were found to have an AOD of 0.05 +/- 0.03, an extinction-to-backscatter ratio (S-ratio) of 33 +/- 6 sr, and peak extinction values around 0.05/km (near the MBL top). The marine results are shown to be in agreement with previously measured and expected values. Polluted marine areas over the Indian Ocean, influenced by continental aerosols, had AOD values in excess of 0.2, S-ratios well above 40 sr, and peak extinction values approximately 0.20/km (near the MBL top). The polluted marine results are shown to be similar to previously published values for continental aerosols. Comparisons between MPL derived extinction near the ship (75 m) and extinction calculated at ship-level using scattering measured by a nephelometer and absorption using a PSAP were conducted. The comparisons indicated that the MPL algorithm (using a constant S-ratio throughout the lower troposphere) calculates extinction near the surface in agreement with the ship-level measurements only when the MBL aerosols are well mixed with aerosols above. Finally, a review of the MPL extinction profiles showed that the model of aerosol vertical extinction developed during an earlier INDOEX field campaign (at the Maldives) did not correctly describe the true vertical distribution over the greater Indian Ocean region. Using the average extinction profile and AOD obtained during marine conditions, a new model of aerosol vertical extinction was determined for marine atmospheres over the Indian Ocean. A new model of aerosol vertical extinction for polluted marine atmospheres was also developed using the average extinction profile and AOD obtained during marine conditions influenced by continental aerosols.

Welton, Ellsworth J.↗

NASA NTRS1985

Sea floor swells and mantle plumes

Most of the intraplate oceanic hot spots are located on the crest of broad topographic swells in the sea floor. These swells have Gaussian shaped profiles, with up to 1.6 km of relief and half widths of 200 to 300 km. Swells are accompanied by positive geoid height anomalies with amplitudes of 6 to 8 m. In the Atlantic and Pacific basins swells cover an area equal to 10% of the Earth's surface. Next to boundary layer contraction, swells are the most important cause of uplift and subsidence in oceanic lithosphere. Calculation of buoyancy supported topography and geoid height were combined with uplift data from laboratory experiments to assess whether sea floor swell can be produced by mantle plumes. The critical constraints are: (1) swell topographic profiles; (2) geoid height/topographic height ratios; and (3) uplift rates, estimated to be 0.2 km/ma.

Olson, P.↗

DOE OSTI2025

Boundary-Layer-Coupled and Decoupled Clouds in Global Storm-Resolving Models: Comparisons With the ARM Observations

The accurate representation of interactions between clouds and planetary boundary layer (PBL) is a persistent challenge in climate models, critical for simulating surface energy budget. The emergence of kilometer-grid-scale global storm resolving models (GSRMs) offers the potential for enhanced details of PBL processes in these complex interactions. This study evaluates the representation of PBL-coupled and decoupled clouds in nine GSRM simulations against extensive ground-based observations by the Department of Energy Atmospheric Radiation Measurement (ARM) program, across six sites encompassing diverse regimes such as marine and continental environments in tropics and midlatitude. By differentiating coupling based on the relative positions between cloud bases and PBL tops, our analysis focuses on the simulation of PBL height, cloud frequency, position and vertical extent. The GSRMs generally exhibit commendable agreements with observed cloud structures and PBL diurnal cycles across different ARM sites. In contrast to the relatively consistent representation of decoupled clouds, discrepancies exist between the simulated and the observed coupled clouds, particularly in areas of intense convection, for example, over tropical rainforests and mountainous regions. These biases are probably associated with the models' tendency to underestimate the boundary layer humidity and the frequency of coupled clouds within different ranges of PBL heights. This study underscores the importance for continuous improvements in the representation of boundary layer and convection within these global kilometer-grid-scale models.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2010

Roles of Engineering Correlations in Hypersonic Entry Boundary Layer Transition Prediction

Efforts to design and operate hypersonic entry vehicles are constrained by many considerations that involve all aspects of an entry vehicle system. One of the more significant physical phenomenon that affect entry trajectory and thermal protection system design is the occurrence of boundary layer transition from a laminar to turbulent state. During the Space Shuttle Return To Flight activity following the loss of Columbia and her crew of seven, NASA's entry aerothermodynamics community implemented an engineering correlation based framework for the prediction of boundary layer transition on the Orbiter. The methodology for this implementation relies upon the framework of correlation techniques that have been in use for several decades. What makes the Orbiter boundary layer transition correlation implementation unique is that a statistically significant data set was acquired in multiple ground test facilities, flight data exists to assist in establishing a better correlation and the framework was founded upon state of the art chemical nonequilibrium Navier Stokes flow field simulations. The basic tenets that guided the formulation and implementation of the Orbiter Return To Flight boundary layer transition prediction capability will be reviewed as a recommended format for future empirical correlation efforts. The validity of this approach has since been demonstrated by very favorable comparison of recent entry flight testing performed with the Orbiter Discovery, which will be graphically summarized. These flight data can provide a means to validate discrete protuberance engineering correlation approaches as well as high fidelity prediction methods to higher confidence. The results of these Orbiter engineering and flight test activities only serve to reinforce the essential role that engineering correlations currently exercise in the design and operation of entry vehicles. The framework of information-related to the Orbiter empirical boundary layer transition prediction capability will be utilized to establish a fresh perspective on this role, to illustrate how quantitative statistical evaluations of empirical correlations can and should be used to assess accuracy and to discuss what the authors' perceive as a recent heightened interest in the application of high fidelity numerical modeling of boundary layer transition. Concrete results will also be developed related to empirical boundary layer transition onset correlations. This will include assessment of the discrete protuberance boundary layer transition onset data assembled for the Orbiter configuration during post-Columbia Return To Flight. Assessment of these data will conclude that momentum thickness Reynolds number based correlations have superior coefficients and uncertainty in comparison to roughness height based Reynolds numbers, aka Re(sub k) or Re(sub kk). In addition, linear regression results from roughness height Reynolds number based correlations will be evaluated, leading to a hypothesis that non-continuum effects play a role in the processes associated with incipient boundary layer transition on discrete protuberances.

Campbell, Charles H.↗

DOE OSTI2021

A GPU-based Approach for Path Planning Optimization via Travel Length Reduction

Typically, before constructing an object with an additive manufacturing system, the 3D object must be sent through a process called slicing. Slicing converts a 3D object commonly in the form of an STL file into a set of layers by horizontally intersecting a plane with the object at various heights. At each height, called a layer, multiple 2D polygons can be generated. Each polygon represents a boundary for solid geometry and is called an island. Each island is then comprised of multiple path types in an attempt to optimally fill the polygon. To move between each island and each islands’ paths, travels are inserted. Travels are simply motion by the system to move from one area of construction to another. Travels do not contribute to the construction of the object, and so, are considered wasted motion. In large-scale additive manufacturing, objects can be quite large and the distance between islands can be large as well. As a result, these travels can waste a significant amount of time. Ideally, travels would be as short as possible, however, computing global minimal travel paths is computationally expensive. To combat this problem, researchers at Oak Ridge National Lab developed a GPU-based approach to travel insertion based on a unique factoradic representation. This representation was then utilized by the GPU to solve the Traveling Salesman Problem (TSP). This algorithm was able to compute global minimal travel paths quickly resulting in faster object construction. A general investigation was also carried out to determine when a GPU vs CPU implementation would be beneficial.

Borish, Michael↗

NASA NTRS1980

A study of tornadic thunderstorm interactions with thermal boundaries

A study of tornadic thunderstorm interactions with thermal boundaries using a model of subcloud wind profiles is presented. Within a hot, moist, and conditionally unstable air mass, warm thermal advection and surface friction cause the winds to veer and increase with height, while within a cool, moist air mass cool thermal advection and friction combine to produce a wind profile that has maximum speeds near the surface and veers little with height. The spatial distribution of different wind profiles and moisture contents within the boundary layer may act together to maximize mesoscale moisture contents, convergence, and cyclonic vorticity within a narrow mixing zone along the thermal boundary.

Maddox, R. A.↗