Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional reasoning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

A composition comparison between comets P/Halley and P/Brorsen-Metcalf

The appearance of comet Brorsen-Metcalf in 1989 following only a few years on the heels of comet Halley in 1986 gave an unusual opportunity to compare two comets of similar orbital elements but potentially different physical and chemical characteristics. Photometric spectral data were acquired for Brorsen-Metcalf on two dates: 13 July 1989 and 2 August 1989. The observations were performed with the 154 cm Catalina Telescope of the University of Arizona Observatories. The spectrum for 13 July 1989 is compared to a Halley spectrum. The general appearance of the spectra is very similar, both comets showing emission due to C2, NH2, OI(D-1), and CN. Neither displays any emission features that are exclusive to only one of the two. Since water is now reasonably well established as the major driving force in the activity of a comet, the H2O production rate for comet Brorsen-Metcalf was calculated. The relative ratios between the production rates of the various species obtained from the data are presented. Results are summarized in tabular form. All species are compared to the H2O production rate of the two comets. The results indicate that C2 originates from an extended source of dust particles or small polymers in addition to parent molecules. The lower production rates of C2 and CN in Brorsen-Metcalf correlate well with both the lower dust production and their smaller increase as the comet approaches the sun. Even without a mode, the spectroscopic observations of Brorsen-Metcalf allowed significant compositional conclusions to be drawn. The NH2 abundance is lower by about a factor of three which appears to be independent of heliocentric distance. Both C2 and CN are less abundant in Brorsen-Metcalf than in Halley and do not seem to participate as much in the strong increase as the comet approaches the sun. The lower H2O production rate implies that the active surface area of the comet Brorsen-Metcalf is much smaller, or equivalently the comet as a whole is much smaller. The substantially lower continuum level for Brorsen-Metcalf cannot readily be explained by smaller or larger active surface area, and must be intrinsic to the comet's embedded dust-to-ice ratio, or to an overall smaller-sized dust grain population.

Disanti, Michael A.↗
NASA NTRS1979

Middle- and far-ultraviolet observations of hot white dwarfs

Observations of HD 149499 B, the previously unrecognized white dwarf star found by the Skylab ultraviolet objective-prism survey, are discussed. Spectra of the binary HD 149499 AB were obtained by the short wavelength and long wavelength cameras of the IUE, and converted into fluxes. The absorption line strengths of the white dwarf secondary indicate a He/H composition ratio greater than or equal to 1. Comparison with model atmospheres of the IUE data suggests a temperature of around 93,000 K for HD 149499 B, while comparison with visual magnitude data indicates a temperature of 82,000 K. Either temperature value would make the star the hottest white dwarf for which reasonably reliable temperature estimates are available. Future work intended includes the repetition of the Skylab ultraviolet experiment on Spacelab for the detection of a complete sample of hot white dwarfs and subdwarfs.

Parsons, S. B.↗
NASA NTRS1993

Mass and spatial distribution of carbonaceous component in Comet Halley

Cometary grains containing large amounts of carbon and/or organic matter were discovered by in situ measurements of cometary dust composition during VEGA and GIOTTO fly-by missions. In accordance with the classification for the data of PUMA-1 and PUMA-2 mass-spectrometers on board the VEGA spacecraft, particles with a ratio of C to any rock-forming element (Mg, Si, Fe, Ca etc.) greater than 10, were categorized as CHON. There are 464 such particles in PUMA-1 data and 51 in PUMA-2 data. Application of cluster analysis to these grains revealed several distinct compositional classes, namely: (H,C,N,O), (H,C,N), (H,C), (H,C,O), (C,N), (C,O), (C,N,O), and (C). Similar classes were identified among particles analyzed by PIA. Also, about a third of all particles fell into groups (H) and (O) characterized by abundances of these elements beyond chemically reasonable limits.

Fomenkova, M.↗
NASA NTRS1996

From Stardust to Planetesimals: Contributed Papers

On June 24 through 26, 1996, a scientific conference entitled From Stardust to Planetesimals was held at the Westin Hotel, Santa Clara, California, as part of the 108th annual meeting of the Astronomical Society of the Pacific. Over the last decade, our understanding of the formation and early evolution of the solar system has advanced considerably due to progress that has been made simultaneously on many fronts. Stardust has been isolated in meteorites and interplanetary dust particles (IDP's), providing us with sample materials which predate the solar system and which offer clues to the processing that has occurred. At the same time, infrared studies have led to a better characterization of the composition of interstellar dust, which is now readily accepted as an important component of the interstellar medium infrared observations have also provided a much better view of the star-formation process and the role of dust therein. Recently, the presence of Kuiper Belt planetesimals has been confirmed and spectroscopy of these rather pristine objects may soon become available. Analysis of spacecraft data from the Comet Halley flybys has yielded a wealth of information on the composition of this comet. These observational advances have changed our understanding of planetesimal processing. The launch of the Infrared Space Observatory, the opening of 10-meter class telescopes, and, in the longer term, the Rosetta mission, promise to continue to broaden and deepen our understanding of the evolution from stardust to planetesimals. For these reasons we considered it timely to organize a meeting focused on the processes that connect stardust and planetesimals. The goal of this meeting was, therefore, to bring together astronomers interested in star- and planet-formation, planetary scientists studying early solar system relics, laboratory scientists studying the processing of analogs, and scientists analyzing meteorites and interplanetary dust particles, grain by grain. As a result of this endeavor, over 200 participants, including 153 scientists from 14 different countries, gathered to discuss the origin and evolution of stardust. We hope that this encounter in Santa Clara will foster an ongoing interchange of information and ideas within this diverse group of scientists. A major aim of this meeting was to produce conference proceedings which reflect the current situation regarding the evolution from stardust to planetesimals.

Kress, M. E.↗
NASA NTRS2007

Investigation of MMOD Impact on STS-115 Shuttle Payload Bay Door Radiator

The Orbiter radiator system consists of eight individual 4.6 m x 3.2 m panels located with four on each payload bay door. Forward panels #1 and #2 are 2.3 cm thick while the aft panels #3 and #4 have a smaller overall thickness of 1.3 cm. The honeycomb radiator panels consist of 0.028 cm thick Aluminum 2024-T81 facesheets and Al5056-H39 cores. The face-sheets are topped with 0.005 in. (0.127 mm) silver-Teflon tape. The radiators are located on the inside of the shuttle payload bay doors, which are closed during ascent and reentry, limiting damage to the on-orbit portion of the mission. Post-flight inspections at the Kennedy Space Center (KSC) following the STS-115 mission revealed a large micrometeoroid/orbital debris (MMOD) impact near the hinge line on the #4 starboard payload bay door radiator panel. The features of this impact make it the largest ever recorded on an orbiter payload bay door radiator. The general location of the damage site and the adjacent radiator panels can be seen in Figure 2. Initial measurements of the defect indicated that the hole in the facesheet was 0.108 in. (2.74 mm) in diameter. Figure 3 shows an image of the front side damage. Subsequent observations revealed exit damage on the rear facesheet. Impact damage features on the rear facesheet included a 0.03 in. diameter hole (0.76 mm), a approx.0.05 in. tall bulge (approx.1.3 mm), and a larger approx.0.2 in. tall bulge (approx.5.1 mm) that exhibited a crack over 0.27 in. (6.8 mm) long. A large approx.1 in. (25 mm) diameter region of the honeycomb core was also damaged. Refer to Figure 4 for an image of the backside damage to the panel. No damage was found on thermal blankets or payload bay door structure under the radiator panel. Figure 5 shows the front facesheet with the thermal tape removed. Ultrasound examination indicated a maximum facesheet debond extent of approximately 1 in. (25 mm) from the entry hole. X-ray examinations revealed damage to an estimated 31 honeycomb cells with an extent of 0.85 in. x 1.1 in. (21.6 x 27.9 mm). Pieces of the radiator at and surrounding the impact site were recovered during the repair procedures at KSC. They included the thermal tape, front facesheet, honeycomb core, and rear facesheet. These articles were examined at JSC using a scanning electron microscope (SEM) with an energy dispersive x-ray spectrometer (EDS). Figure 6 shows SEM images of the entry hole in the facesheet. The asymmetric height of the lip may be attributed to projectile shape and impact angle. Numerous instances of a glass-fiber organic matrix composite were observed in the facesheet tape sample. The fibers were approximately 10 micrometers in diameter and variable lengths. EDS analysis indicated a composition of Mg, Ca, Al, Si, and O. Figures 7 and 8 present images of the fiber bundles, which were believed to be circuit board material based on similarity in fiber diameter, orientation, consistency, and composition. A test program was initiated in an attempt to simulate the observed damage to the radiator facesheet and honeycomb. Twelve test shots were performed using projectiles cut from a 1.6 mm thick fiberglass circuit board substrate panel. Results from test HITF07017, shown in figures 9 and 10, correlates with the observed impact features reasonably well. The test was performed at 4.14 km/sec with an impact angle of 45 degrees using a cylindrical projectile with a diameter and length of 1.25 mm. The fiberglass circuit board material had a density of 1.65 g/cu cm, giving a projectile mass of 2.53 mg. An analysis was performed using the Bumper code to estimate the probability of impact to the shuttle from a 1.25 mm diameter particle. Table 1 shows a 1.6% chance (impact odds = 1 in 62) of a 1.25 mm or larger MMOD impact on the radiators of the vehicle during a typical ISS mission. There is a 0.4% chance (impact odds = 1 in 260) that a 1.25 mm or larger MMOD particle would impact the RCC wing leading edge and nose cap during a typical miion. Figure 11 illustrates the vulnerable areas of the wing leading edge reinforced carbon-carbon (RCC), an area of the vehicle that is very sensitive to impact damage. The highlighted red, orange, yellow, and light green areas would be expected to experience critical damage if impacted by an OD particle such as the one that hit the RH4 radiator panel on STS-115.

Hyde, J.↗
NASA NTRS2009

NASA Tech Briefs, March 2009

Topics covered include: Improved Instrument for Detecting Water and Ice in Soil; Real-Time Detection of Dust Devils from Pressure Readings; Determining Surface Roughness in Urban Areas Using Lidar Data; DSN Data Visualization Suite; Hamming and Accumulator Codes Concatenated with MPSK or QAM; Wide-Angle-Scanning Reflectarray Antennas Actuated by MEMS; Biasable Subharmonic Membrane Mixer for 520 to 600 GHz; Hardware Implementation of Serially Concatenated PPM Decoder; Symbolic Processing Combined with Model-Based Reasoning; Presentation Extensions of the SOAP; Spreadsheets for Analyzing and Optimizing Space Missions; Processing Ocean Images to Detect Large Drift Nets; Alternative Packaging for Back-Illuminated Imagers; Diamond Machining of an Off-Axis Biconic Aspherical Mirror; Laser Ablation Increases PEM/Catalyst Interfacial Area; Damage Detection and Self-Repair in Inflatable/Deployable Structures; Polyimide/Glass Composite High-Temperature Insulation; Nanocomposite Strain Gauges Having Small TCRs; Quick-Connect Windowed Non-Stick Penetrator Tips for Rapid Sampling; Modeling Unsteady Cavitation and Dynamic Loads in Turbopumps; Continuous-Flow System Produces Medical-Grade Water; Discrimination of Spore-Forming Bacilli Using spoIVA; nBn Infrared Detector Containing Graded Absorption Layer; Atomic References for Measuring Small Accelerations; Ultra-Broad-Band Optical Parametric Amplifier or Oscillator; Particle-Image Velocimeter Having Large Depth of Field; Enhancing SERS by Means of Supramolecular Charge Transfer; Improving 3D Wavelet-Based Compression of Hyperspectral Images; Improved Signal Chains for Readout of CMOS Imagers; SOI CMOS Imager with Suppression of Cross-Talk; Error-Rate Bounds for Coded PPM on a Poisson Channel; Biomorphic Multi-Agent Architecture for Persistent Computing; and Using Covariance Analysis to Assess Pointing Performance.

Source record↗
NASA NTRS1975

An investigation of the failure and fracture behavior of graphite/epoxy laminates

A fundamental investigation of the fracture behavior of fiber reinforced composites is discussed. It is suggested that experimental and analytical investigations should compliment each other. Further, it is suggested that in order to understand and mathematically model composite fracture it is necessary to explore, understand and characterize the stress-strain behavior of each type of laminate tested from initial loading to incipient fracture. That is, it is not only necessary to perform fracture studies but it is necessary to perform stress-strain characterization and failure studies as well. For this reason a literature survey is presented in which these three elements are discussed. An experimental program to determine tensile properties of unnotched and notched unidirectional and multi-directional laminates composed of Hercules AS Fiber and 3501 Resin is described. Experimental unnotched moduli and strengths are presented, discussed and compared to lamination theory predictions. It is shown that rate effects are small and that lamination theory gives good results for moduli but not for strengths.

Brinson, H. F.↗
NASA NTRS1978

The origin of planetary atmospheres

Reasons for the difference in planetary atmospheres are reviewed. Atmospheric formation by outgassing from terrestrial planets is contrasted with the retention of the primary material by the outer planets. The differences in Venusian, earth, and Martian atmospheres are explained in terms of planet distance from the sun. Data on terrestrial planet pressures, temperatures, and gas compositions, as well as on rates and gas composition of outgassing material are presented. The significance of planet mass is considered.

Bauer, S. J.↗
NASA NTRS1979

The hydrogen lines in the high-luminosity quasar B2 1225+31

The emission lines H-alpha, H-beta + forbidden O III, and L-alpha have been observed in the high-redshift quasar 1225+31. The ratios of line intensities in 1225+31 are found to be approximately 0.8 for L-alpha/H-alpha, about 4 for H-alpha/(H-beta + forbidden O III), and between 4 and 10 for H-alpha/H-beta. The observed value of L-alpha/H-alpha agrees well with the ratio derived by Baldwin (1977) on the basis of a composite quasar spectrum, as well as with direct determination of this ratio in 3C 273 and PKS 0237-23. The ratio H-alpha/H-beta is in the range of values found for a sample of low-redshift quasars by Baldwin (1975). The low value for the L-alpha/H-alpha ratio cannot be reasonably explained by foreground extinction between the sun and 1225+31.

Soifer, B. T.↗
NASA NTRS1985

Strength Modeling Report

Strength modeling is a complex and multi-dimensional issue. There are numerous parameters to the problem of characterizing human strength, most notably: (1) position and orientation of body joints; (2) isometric versus dynamic strength; (3) effector force versus joint torque; (4) instantaneous versus steady force; (5) active force versus reactive force; (6) presence or absence of gravity; (7) body somatotype and composition; (8) body (segment) masses; (9) muscle group envolvement; (10) muscle size; (11) fatigue; and (12) practice (training) or familiarity. In surveying the available literature on strength measurement and modeling an attempt was made to examine as many of these parameters as possible. The conclusions reached at this point toward the feasibility of implementing computationally reasonable human strength models. The assessment of accuracy of any model against a specific individual, however, will probably not be possible on any realistic scale. Taken statistically, strength modeling may be an effective tool for general questions of task feasibility and strength requirements.

Badler, N. I.↗
NASA NTRS1986

Estimation of crystallinity in a model thermoplastic composite

Crystallinities as low as 16 percent have been estimated by determination of the interplanar spacing on PET/carbonaceous filament composites with resin content of aobut 25 percent w/w using wide-angle X-ray scattering (WAXS) in the angular range 2 theta = 16-18 deg. The diffraction pattern of the carbonaceous reinforcements masks the major reflections of the resin, and the resin content and the crystallinity are kept low to make the simulation reasonable.

Wakelyn, N. T.↗
NASA NTRS1990

Review of model sensor studies on Pd/SnO2(110) surfaces

Studies performed at the National Institute of Standards and Technology on the model gas sensor system, Pd/SnO2(110), are reviewed. Adsorption and interfacial effects play a primary role in the gas sensing process, as they do in catalysis. For this reason, researchers have used a variety of surface sensitive techniques in the research, including x ray and ultraviolet photoelectron spectroscopies (XPS and UPS), low energy electron diffraction (LEED), and ion scattering spectroscopy (ISS). By combining these complementary techniques with in situ gas response (conductance) measurements, researchers were able to correlate directly sensor activity with the composition and structure of the Pd/SnO2 interface. Although the intent of this work is to develop an understanding of gas sensing mechanisms, its relevance to Pt/SnO2 catalytic systems is obvious.

Fryberger, Teresa B.↗
NASA NTRS1993

Mechanical properties of triaxially braided composites - Experimental and analytical results

This paper investigates the unnotched tensile properties of two-dimensional (2D) triaxial braid-reinforced composites both experimentally and analytically. The materials are graphite fibers in an epoxy matrix. Three different reinforcing fiber architectures were considered. There were considerable differences in the observed elastic constants from different size strain gage and extensometer readings. Larger strain gages gave more consistent results and correlated better with the extensometer readings. Experimental strains correlated reasonably well with analytical predictions in the longitudinal, 0 deg, fiber direction but not in the transverse direction. Tensile strength results were not always predictable even in reinforcing directions. Minor changes in braid geometry led to disproportionate strength variations. The unit cell structure of the triaxial braid was discussed with the assistance of computer analysis of the microgeometry. Photomicrographs of braid geometry were used to improve upon the computer graphics representations of unit cells. These unit cells were used to predict the elastic moduli with various degrees of sophistication. The simple and the complex analyses were generally in agreement, but none adequately matched the experimental results for all the braids.

Masters, John E.↗
NASA NTRS2004

The Genesis Mission Solar Wind Collection: Solar-Wind Statistics over the Period of Collection

The NASA Genesis spacecraft was launched August 8, 2001 on a mission to collect samples of solar wind for 2 years and return them to earth September 8, 2004. Detailed analyses of the solar wind ions implanted into high-purity collection substrates will be carried out using various mass spectrometry techniques. These analyses are expected to determine key isotopic ratios and elemental abundances in the solar wind, and by extension, in the solar photosphere. Further, the photospheric composition is thought to be representative of the solar nebula with a few exceptions, so that the Genesis mission will provide a baseline for the average solar nebula composition with which to compare present-day compositions of planets, meteorites, and asteroids. The collection of solar wind samples is almost complete. Collection began for most substrates in early December, 2001, and is scheduled to be complete on April 2 of this year. It is critical to understand the solar-wind conditions during the collection phase of the mission. For this reason, plasma ion and electron spectrometers are continuously monitoring the solar wind proton density, velocity, temperature, the alpha/proton ratio, and angular distribution of suprathermal electrons. Here we report on the solar-wind conditions as observed by these in-situ instruments during the first half of the collection phase of the mission, from December, 2001 to present.

Barraclough, B. L.↗
NASA NTRS2005

Improvements in Fabrication of Sand/Binder Cores for Casting

Three improvements have been devised for the cold-box process, which is a special molding process used to make sand/binder cores for casting hollow metal parts. These improvements are: The use of fiber-reinforced composite binder materials (in contradistinction to the non-fiber-reinforced binders used heretofore), The substitution of a directed-vortex core-blowing subprocess for a prior core-blowing process that involved a movable gassing plate, and The use of filters made from filtration-grade fabrics to prevent clogging of vents. For reasons that exceed the scope of this article, most foundries have adopted the cold-box process for making cores for casting metals. However, this process is not widely known outside the metal-casting industry; therefore, a description of pertinent aspects of the cold-box process is prerequisite to a meaningful description of the aforementioned improvements. In the cold-box process as practiced heretofore, sand is first mixed with a phenolic resin (considered to be part 1 of a three-part binder) and an isocyanate resin (part 2 of the binder). Then by use of compressed air, the mixture is blown into a core box, which is a mold for forming the core. Next, an amine gas (part 3 of the binder) that acts as a catalyst for polymerization of parts 1 and 2 is blown through the core box. Alternatively, a liquid amine that vaporizes during polymerization can be incorporated into the sand/resin mixture. Once polymerization is complete, the amine gas is purged from the core box by use of compressed air. The finished core is then removed from the core box.

Bakhitiyarov, Sayavur I.↗
NASA NTRS2005

Effects of Control Mode and R-Ratio on the Fatigue Behavior of a Metal Matrix Composite

Composite Because of their high specific stiffness and strength at elevated temperatures, continuously reinforced metal matrix composites (MMC's) are under consideration for a future generation of aeropropulsion systems. Since components in aeropropulsion systems experience substantial cyclic thermal and mechanical loads, the fatigue behavior of MMC's is of great interest. Almost without exception, previous investigations of the fatigue behavior of MMC's have been conducted in a tension-tension, load-controlled mode. This has been due to the fact that available material is typically less than 2.5-mm thick and, therefore, unable to withstand high compressive loads without buckling. Since one possible use of MMC's is in aircraft skins, this type of testing mode may be appropriate. However, unlike aircraft skins, most engine components are thick. In addition, the transient thermal gradients experienced in an aircraft engine will impose tension-compression loading on engine components, requiring designers to understand how the MMC will behave under fully reversed loading conditions. The increased thickness of the MMC may also affect the fatigue life. Traditionally, low-cycle fatigue (LCF) tests on MMC's have been performed in load control. For monolithic alloys, low-cycle fatigue tests are more typically performed in strain control. Two reasons justify this choice: (1) the critical volume from which cracks initiate and grow is generally small and elastically constrained by the larger surrounding volume of material, and (2) load-controlled, low-cycle fatigue tests of monolithics invariably lead to unconstrained ratcheting and localized necking--an undesired material response because the failure mechanism is far more severe than, and unrelated to, the fatigue mechanism being studied. It is unknown if this is the proper approach to composite testing. However, there is a lack of strain-controlled data on which to base any decisions. Consequently, this study addresses the isothermal, LCF behavior of a [0]_32 MMC tested under strain- and load-controlled conditions for both zero-tension and tension-compression loading conditions. These tests were run at 427 C on thick specimens of SiC-reinforced Ti-15-3. For the fully-reversed tests, no difference was observed in the lives between the load- and strain-controlled tests. However, for the zero-tension tests, the strain-controlled tests had longer lives by a factor of 3 in comparison to the load-controlled tests. This was due to the fact that under strain-control the specimens cyclically softened, reducing the cracking potential. In contrast, the load-controlled tests ratcheted toward larger tensile strains leading to an eventual overload of the fibers. Fatigue tests revealed that specimens tested under fully-reversed conditions had lives approximately an order of magnitude longer than for those specimens tested under zero tension. When examined on a strain-range basis, the fully reversed specimens had similar, but still shorter lives than those of the unreinforced matrix material. However, the composite had a strain limitation at short lives because of the limited strain capacity of the brittle ceramic fiber. The composite also suffered at very high lives because of the lack of an apparent fatigue limit in comparison to the unreinforced matrix. The value of adding fibers to the matrix is apparent when the fatigue lives are plotted as a function of stress range. Here, the composite is far superior to the unreinforced matrix because of the additional load-carrying capacity of the fibers.

Source record↗
NASA NTRS1979

The condensation and fractionation of refractory lithophile elements

It is noted that Cr, Mg, and Si are fractionated in chondritic material along with, but to a lesser extent than, a large group of more refractory elements. These patterns are reexamined with the reasoning that this might imply some unique distribution at the time of fractionation. It is shown that apparently two distinct fractionization patterns can be resolved: one involving ordinary and enstatite chondrites and the other involving carbonaceous chondrites, the earth, the moon, and the eucrite parent body. It is noted that the two trends intersect at C1 composition. Attention is given to the range in which the largest fraction of planetary matter condenses. It is concluded that the appearance of large amounts of condensed materials is conceivably in some way related to the fractionization process, although the exact relationship cannot be specified.

Larimer, J. W.↗
NASA NTRS1993

Low-gravity electrodeposition and growth of polymer thin films with large third-order optical nonlinearities by electrochemical processes for devices: Thiophene-based polymers

It has been proposed that NLO thin film properties may be improved by low-gravity processing. Strong candidates for NLO thin film applications are the polythiophenes. Polymeric thiophenes are attractive materials due to their ease of preparation, stability, and high X(exp 3). A simple and convenient method for preparation of polythiophenes is electrochemical oxidation. We will apply some of our experience and lessons learned in low-gravity metal, metal/cermet electrode position to improve the quality of polythiophene(s) thin films. In low gravity electrode position of Ni at a high rate on an Au substrate often results in the production of an x-ray non diffracting surface. Cobalt metal deposition does not give this result nor does Ni when deposited similarly on a glassy carbon substrate. Co/Ni alloy composition produced during electrode position is strongly dependent upon the amount of convection. Code position of neutral inert cermets with metals is influenced significantly by the presence of gravity and the size of the cermets. Tracks left in the 1-g surfaces by unsuccessful particle occlusion indicate suspension of the large particles is not the only reason for poor volume percentages of the larger particles in the deposits. All size particles are more homogeneously distributed in the deposits in low-gravity electrocodeposition than in 1-g. Low gravity gives larger volume percentages for the larger particles in the deposits, while 1-g gives larger volume percentages for the smaller particles. Intermediate size particles give mixed results. The experimental cells were constructed with flat electrode end plates such that 1-g bench reference electrode positions could be carried out at various orientations with respect to gravity. A series of bench studies using similar designed cells are suggested so that convection modification can be applied to electrochemical thin film preparation. Convection effects can then be coupled with other parameter variations in current, temperature, concentration, solvent, electrolyte, and anode substrates to optimize the properties of NLO thin films before resorting to low-gravity processing.

Penn, Benjamin G.↗