Search NASA⌕ Search

SEARCH · Search NASA

Results for “control interactions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Reduction of blade-vortex interaction noise through higher harmonic pitch control

An acoustics test using an aeroelastically scaled rotor was conducted to examine the effectiveness of higher harmonic blade pitch control for the reduction of impulsive blade-vortex interaction (BVI) noise. A four-bladed, 110 in. diameter, articulated rotor model was tested in a heavy gas (Freon-12) medium in Langley's Transonic Dynamics Tunnel. Noise and vibration measurements were made for a range of matched flight conditions, where prescribed (open-loop) higher harmonic pitch was superimposed on the normal (baseline) collective and cyclic trim pitch. For the inflow-microphone noise measurements, advantage was taken of the reverberance in the hard walled tunnel by using a sound power determination approach. Initial findings from on-line data processing for three of the test microphones are reported for a 4/rev (4P) collective pitch control for a range of input amplitudes and phases. By comparing these results to corresponding baseline (no control) conditions, significant noise reductions (4 to 5 dB) were found for low-speed descent conditions, where helicopter BVI noise is most intense. For other rotor flight conditions, the overall noise was found to increase. All cases show increased vibration levels.

Brooks, Thomas F.↗
NASA NTRS1989

A spaceborne optical interferometer: The JPL CSI mission focus

The JPL Control Structure Interaction (CSI) program is part of the larger NASA-wide CSI program. Within this larger context, the JPL CSI program will emphasize technology for systems that demand micron or sub-micron level control, so-called Micro-Precision Controlled Structures (u-PCS). The development of such technology will make it practical to fly missions with large optical or large precision antenna systems. In keeping with the focused nature of the desired technology, the JPL approach is to identify a focus mission, develop the focus mission CSI system design to a preliminary level, and then use this design to drive out requirements for CSI technology development in the design and analysis, ground test bed, and flight experiment areas.

Laskin, R. A.↗
NASA NTRS1992

Active structural control for the mini-MAST and ACES structures

Two experiments based on the maximum entropy/optimal projection design approach are discussed which were conducted by Harris Corporation as part of the NASA Controls Structures Interaction Guest Investigator program. The design equations consist of four coupled matrix equations which specialize to the standard linear-quadratic Guassian Riccati equations, when the plant is known perfectly and a full order controller is desired. These experiments demonstrate successful control system design and implementation for flexible structures.

Collins, E. G., Jr.↗
NASA NTRSDate not supplied

Spacecraft Observatory Benchmark Problem for Optical Disturbance Rejection

Since mid-1980s NASA has launched several first-generation interplanetary observatory missions. A salient feature of these missions has been the mounting of the optical payload on top of a large flexible space structure. This imposes challenging control-structure interaction problems (CSI) that have been studied over several decades. The Dec. 2021 launch of the James Webb Telescope marks the latest example of such a mission. One way to encourage development of novel control methods is to provide a benchmark problem for researchers. By the mid-2000s, there were a few well-known benchmark problems developed by the control community with a focus on CSI applications. However, in the past 15 years, the control challenges in optical observation missions have shifted from CSI to line-of-sight (LOS) precision pointing. This is because popular designs of the second-generation (Gen II) space earth missions have eliminated the large structure interface by mounting the optical payload directly on top of a rigid bus platform. The focus now is to achieve accurate pointing with maximum rejection of the surrounding disturbances. The NASA Safety and Engineering Center (NESC) has tasked T he Aerospace Corporation to develop a Benchmark Problem to study the challenging control issues that Gen II observatory missions encounter. This software tool is to be released as a public domain platform aimed at government, academic, and industry researchers. The focus of this benchmark problem is for researchers to design a set of innovative payload control laws with the maximum Optical Disturbance Rejection (ODR) capability to meet a set of pre-defined μrad-level of LOS jitter requirements. This paper describes the development of the benchmark problem. Aerospace/NASA will provide an integrated LOS plant model and disturbance/command profiles for users to run their design and simulation with as well as a user’s guide describing the required interfaces. The Aerospace Corp is also working to develop a hardware fast steering mirror testbed for users to demonstrate their innovative design in real hardware, if so desired.

Spacecraft Observatory Benchmark Problem↗
NASA NTRS1985

Interactive computer graphics and its role in control system design of large space structures

This paper attempts to show the relevance of interactive computer graphics in the design of control systems to maintain attitude and shape of large space structures to accomplish the required mission objectives. The typical phases of control system design, starting from the physical model such as modeling the dynamics, modal analysis, and control system design methodology are reviewed and the need of the interactive computer graphics is demonstrated. Typical constituent parts of large space structures such as free-free beams and free-free plates are used to demonstrate the complexity of the control system design and the effectiveness of the interactive computer graphics.

Reddy, A. S. S. R.↗
NASA NTRS1998

Some Formal Aspects of Human-Machine Interaction

While automated control systems such as autopilots and medical devices are introduced at a rapid pace, it is widely recognized that user interaction with these machines is problematic (Abbott, Slotte, & Stimson, 1996). One factor commonly cited in the literature is the discrepancy between the machine's behavior and the user's expectations. Design guidelines to reduce this discrepancy focus on two elements: (1) improvement of the "feedback" about what the automation is actually doing, and (2) improvement of the user's "mental model" of the automation (Norman, 1990; Sarter and Woods, 1995). This presentation describes a methodology for investigating these two elements via a formal (Le., mathematical) approach. The method involves two representations: (1) a finite state model of the machine's behavior (2) a finite state model of the user's knowledge and expectations about the machine's behavior. In the analysis phase we compare these two models and identify discrepancies. Such discrepancies can be compensated by augmenting the display and/or the user's model. A taxonomy of these discrepancies will be discussed using examples from automated Eight control systems of modern "glass cockpit" jetliners.

Degani, Asaf↗
NASA NTRS1989

Computational architecture for integrated controls and structures design

To facilitate the development of control structure interaction (CSI) design methodology, a computational architecture for interdisciplinary design of active structures is presented. The emphasis of the computational procedure is to exploit existing sparse matrix structural analysis techniques, in-core data transfer with control synthesis programs, and versatility in the optimization methodology to avoid unnecessary structural or control calculations. The architecture is designed such that all required structure, control and optimization analyses are performed within one program. Hence, the optimization strategy is not unduly constrained by cold starts of existing structural analysis and control synthesis packages.

Belvin, W. Keith↗
NASA NTRS1992

Longitudinal vortex control - Techniques and applications (The 32nd Lanchester Lecture)

A summary is presented of vortex control applications and current techniques for the control of longitudinal vortices produced by bodies, leading edges, tips and intersections. Vortex control has up till now been performed by many approaches in an empirical fashion, assisted by the essentially inviscid nature of much of longitudinal vortex behavior. Attention is given to Reynolds number sensitivities, vortex breakdown and interactions, vortex control on highly swept wings, and vortex control in juncture flows.

Bushnell, D. M.↗
NASA NTRS1991

Optical pathlength control in the nanometer regime on the JPL phase B interferometer testbed

This paper describes experimental research being performed at the Jet Propulsion Laboratory to develop and validate control concepts arising out of NASA's Control Structure Interaction program. The facility is meant to be a ground testbed with relevance to a broad class of future precision optical space systems. The objective of the experimental program is to investigate a multi-layer control approach to the maintenance of nanometer level optical pathlength control in the presence of external disturbances and multiple structural resonances. A brief overview of the experimental facility is presented. The control design methodology is discussed, and several experimental results are presented.

O'Neal, Michael C.↗
NASA NTRS2000

Svalbard: A Window for Understanding Temporal/Spatial Aspects of Solar Wind Coupling to the Magnetosphere and Ionosphere

The research facilities on the Svalbard archepelego provide a unique opportunity for observing the temporal and spatial characteristics of the interaction of the solar wind with the magnetosphere-ionosphere system. The first sounding rockets from the SvdRak range at Ny-Alesund have opened a new perspective for separating temporal and spatial effects. Finding a correlation between observations from the rockets and the Wind satellite located nearly 200 R(sub E) upstream in the solar wind that had a lag time less than the advection time forced consideration of tilted phase planes of the interp1anetary electric field. From this it was deduced that the interaction process has to involve high latitude merging, the interplanetary magnetic field (IMF) B(sub Y) bifurcates the cusp relative to the high latitude source regions in the Northern and Southern Hemispheres, IMF B(sub X) controls the interaction time in each hemisphere, and the small convection cell is driven by opposite hemisphere merging. Studies with 4 satellites in the solar wind have shown that the tilt of the phase plane varies on a minute-by-minute basis and change significantly on time scales of tens of minutes. Images of the cusp at 557.7 nm provide a nearly instantaneous picture of the temporal and spatial characteristics of merging at the magnetopause and show that the process can occur at multiple locations. The rate and location vary with time.

Maynard, Nelson C.↗
NASA NTRS1989

Controls Astrophysics and Structures Experiment in Space (CASES) advanced studies and planning

The CASES (Controls, Astrophysics, and Structures Experiment in Space) program consists of a flight demonstration of CSI (Controls-Structures Interactions) technology on the Space Shuttle. The basis structure consists of a 32 m deployable boom with actuators and sensors distributed along its length. Upon deployment from the Orbiter bay, the CASES structure will be characterized dynamically and its deformations controlled by a series of experimental control laws; and cold gas thrusters at its tip will be used to orient the Orbiter to a fixed celestial reference. The scientific observations will consist of hard x-ray imaging, at high resolution, of the Sun and the Galactic center. The hard x-ray observations require stable (few arc min) pointing at these targets for one or more position-sensitive proportional counters in the Orbiter bay, which view the object to be imaged through an aperture-encoding mask at the boom tip. This report gives the concensus developed at the second CASES Science Working Group meeting, which took place at NASA Marshall Space Flight Center May 16-17, 1990. An earlier paper and scientific summaries are available and form the basis for the present discussion.

Wu, S. T.↗
NASA NTRS1993

Integrated design and experimental validation of the CSI evolutionary structure

An experimental validation of the optimization-based integrated design methodology performed under the Controls-Structures Interaction (CSI) program for a class of flexible spacecraft is reviewed. The studies have been performed using an integrated design software tool which is under development at the NASA-Langley Research Center. It is analytically and experimentally demonstrated that integrated controls-structures design can yield designs which are substantially superior to those obtained through the traditional sequential approach.

Maghami, P. G.↗
NASA NTRS1991

Control of a flexible beam using fuzzy logic

The goal of this project, funded under the NASA Summer Faculty Fellowship program, was to evaluate control methods utilizing fuzzy logic for applicability to control of flexible structures. This was done by applying these methods to control of the Control Structures Interaction Suitcase Demonstrator developed at Marshall Space Flight Center. The CSI Suitcase Demonstrator is a flexible beam, mounted at one end with springs and bearing, and with a single actuator capable of rotating the beam about a pin at the fixed end. The control objective is to return the tip of the free end to a zero error position (from a nonzero initial condition). It is neither completely controllable nor completely observable. Fuzzy logic control was demonstrated to successfully control the system and to exhibit desirable robustness properties compared to conventional control.

Mccullough, Claire L.↗
NASA NTRS1996

Experimental Validation of an Integrated Controls-Structures Design Methodology

The first experimental validation of an integrated controls-structures design methodology for a class of large order, flexible space structures is described. Integrated redesign of the controls-structures-interaction evolutionary model, a laboratory testbed at NASA Langley, was described earlier. The redesigned structure was fabricated, assembled in the laboratory, and experimentally tested against the original structure. Experimental results indicate that the structure redesigned using the integrated design methodology requires significantly less average control power than the nominal structure with control-optimized designs, while maintaining the required line-of-sight pointing performance. Thus, the superiority of the integrated design methodology over the conventional design approach is experimentally demonstrated. Furthermore, amenability of the integrated design structure to other control strategies is evaluated, both analytically and experimentally. Using Linear-Quadratic-Guassian optimal dissipative controllers, it is observed that the redesigned structure leads to significantly improved performance with alternate controllers as well.

Maghami, Peiman G.↗
NASA NTRSDate not supplied

Integrating Upper Class E Traffic Management (ETM) Operations into the National Airspace System: Use Cases and Research Questions

As new categories of vehicles are introduced in the National Airspace System, so too are novel concepts for a cooperative approach to traffic management environments. One of these new environments, Upper Class E Traffic Management (ETM), is expected to include a variety of high altitude, long endurance vehicles with a range of performance capabilities and mission profiles that operate in cooperative areas above 60,000 feet. In addition to developing the rules, architecture, and systems for operations within the ETM environment itself, it is also important to consider how ETM vehicles will integrate with traditional Air Traffic Management and interact with Air Traffic Control (ATC) as they traverse ATC-controlled airspace and transition in and out of cooperative ETM operating areas. As a first step toward future ETM demonstrations at the National Aeronautics and Space Administration (NASA) Ames Research Center’s Airspace Operations Laboratory, use cases with step-by-step procedures were developed to identify both nominal and off-nominal scenarios in which ETM operations will interact with ATC. As NASA prepares to develop a simulation platform to demonstrate ETM cooperative practices and ETM-ATC interactions, the procedures, ATC roles and responsibilities, data exchange requirements, and research questions that were identified as part of use case development will inform scenario and system architecture design. The upcoming simulation work will include initial prototype ETM-ATC coordination tools to support ATC controllers’ interactions with ETM operations. This paper will briefly discuss NASA’s upcoming ETM development work and then provide background on ETM-ATC interactions, describe each ETM-ATC interaction use case, and discuss open questions on concept, procedures, and assumptions.

ATC↗
NASA NTRSDate not supplied

Integrating Upper Class E Traffic Management (ETM) Operations into the National Airspace System: Use Cases and Research Questions

As new categories of vehicles are introduced in the National Airspace System, so too are novel concepts for a cooperative approach to traffic management environments. One of these new environments, Upper Class E Traffic Management (ETM), is expected to include a variety of high altitude, long endurance vehicles with a range of performance capabilities and mission profiles that operate in cooperative areas above 60,000 feet. In addition to developing the rules, architecture, and systems for operations within the ETM environment itself, it is also important to consider how ETM vehicles will integrate with traditional Air Traffic Management and interact with Air Traffic Control (ATC) as they traverse ATC-controlled airspace and transition in and out of cooperative ETM operating areas. As a first step toward future ETM demonstrations at the National Aeronautics and Space Administration (NASA) Ames Research Center’s Airspace Operations Laboratory, use cases with step-by-step procedures were developed to identify both nominal and off-nominal scenarios in which ETM operations will interact with ATC. As NASA prepares to develop a simulation platform to demonstrate ETM cooperative practices and ETM-ATC interactions, the procedures, ATC roles and responsibilities, data exchange requirements, and research questions that were identified as part of use case development will inform scenario and system architecture design. The upcoming simulation work will include initial prototype ETM-ATC coordination tools to support ATC controllers’ interactions with ETM operations. This paper will briefly discuss NASA’s upcoming ETM development work and then provide background on ETM-ATC interactions, describe each ETM-ATC interaction use case, and discuss open questions on concept, procedures, and assumptions.

ATC↗
NASA NTRS2006

System Engineering and Integration of Controls for Advanced Life Support

The Advanced Integration Matrix (AIM) project at the Johnson Space Center (JSC) was chartered to study and solve systems-level integration issues for exploration missions. One of the first issues identified was an inability to conduct trade studies on control system architectures due to the absence of mature evaluation criteria. Such architectures are necessary to enable integration of regenerative life support systems. A team was formed to address issues concerning software and hardware architectures and system controls.. The team has investigated what is required to integrate controls for the types of non-linear dynamic systems encountered in advanced life support. To this end, a water processing bioreactor testbed is being developed which will enable prototyping and testing of integration strategies and technologies. Although systems such as the water bioreactors exhibit the complexities of interactions between control schemes most vividly, it is apparent that this behavior and its attendant risks will manifest itself among any set of interdependent autonomous control systems. A methodology for developing integration requirements for interdependent and autonomous systems is a goal of this team and this testbed. This paper is a high-level summary of the current status of the investigation, the issues encountered, some tentative conclusions, and the direction expected for further research.

Overland, David↗