Results for “correlation model” — Page 25

NASA NTRS2004

Testing the PV-Theta Mapping Technique in a 3-D CTM Model Simulation

Mapping lower stratospheric ozone into potential vorticity (PV)- potential temperature (Theta) coordinates is a common technique employed to analyze sparse data sets. Ozone transformed into a flow-following dynamical coordinate system is insensitive to meteorological variations. Therefore data from a wide range of times/locations can be compared, so long as the measurements were made in the same airmass (as defined by PV). Moreover, once a relationship between ozone and PV/Theta is established, a full 3D ozone field can be estimated from this relationship and the 3D analyzed PV field. However, ozone data mapped in this fashion can be hampered by noisy PV fields, or "mis-matches" in the resolution and/or exact location of the ozone and PV measurements. In this study, we investigate the PV-ozone relationship using output from a recent 50-year run of the Goddard 3D chemical transport model (CTM). Model constituents are transported using off-line dynamics from the finite volume general circulation model (FVGCM). By using the internally consistent model PV and ozone fields, we minimize noise due to mis-matching and resolution issues. We calculate correlations between model ozone and PV throughout the stratosphere, and test the sensitivity of the technique to initial data resolution. To do this we degrade the model data to that of various satellite instruments, then compare the mapped fields derived from the sub-sampled data to the full resolution model data. With these studies we can determine appropriate limits for the PV-theta mapping technique in latitude, altitude, and as a function of original data resolution.

Frith, Stacey M.↗

NASA NTRS2004

A Variable Turbulent Schmidt Number Formulation for Scramjet Application

In high speed engines, thorough turbulent mixing of fuel and air is required to obtain high performance and high efficiency. Thus, the ability to predict turbulent mixing is crucial in obtaining accurate numerical simulation of an engine and its performance. Current state of the art in CFD simulation is to assume both turbulent Prandtl number and Schmidt numbers to be constants. However, since the mixing of fuel and air is inversely proportional to the Schmidt number, a value of 0.45 for the Schmidt number will produce twice as much diffusion as that with a value of 0.9. Because of this, current CFD tools and models have not been able to provide the needed guidance required for the efficient design of a scramjet engine. The goal of this investigation is to develop the framework needed to calculate turbulent Prandtl and Schmidt numbers as part of the solution. This requires four additional equations: two for the temperature variance and its dissipation rate and two for the concentration variance and its dissipation rate. In the current investigation emphasis will be placed on studying mixing without reactions. For such flows, variable Prandtl number does not play a major role in determining the flow. This, however, will have to be addressed when combustion is present. The approach to be used is similar to that used to develop the k-zeta model. In this approach, relevant equations are derived from the exact Navier-Stokes equations and each individual correlation is modeled. This ensures that relevant physics is incorporated into the model equations. This task has been accomplished. The final set of equations have no wall or damping functions. Moreover, they are tensorially consistent and Galilean invariant. The derivation of the model equations is rather lengthy and thus will not be incorporated into this abstract, but will be included in the final paper. As a preliminary to formulating the proposed model, the original k-zeta model with constant turbulent Prandtl and Schmidt numbers is used to model the supersonic coaxial jet mixing experiments involving He, O2 and air.

Xiao, X.↗

NASA NTRSDate not supplied

Comparing Two Statistical Models for Low Boom Dose-response Relationships with Correlated Responses

This study compares two statistical modeling approaches to construct summary dose-response curves for low boom community noise surveys. NASA field survey data were used that consist of multiple responses from a survey participant. These data require an approach that accounts for the correlation among repeated annoyance observations from the same participant. A multilevel model accounts for the correlation by allowing estimated parameters to vary with each survey participant. On the other hand, a population average model utilizes generalized estimating equations and accounts for the correlation via a user-specified within-subject correlation structure. A visual comparison of the dose-response curves for these two methods reveals similar results. When comparing specific points along the summary curves, the multilevel model yields more precise confidence bounds than the population average model. The similarity between the summary curves derived from each model lends validity to both approaches for approximating a population representative summary curve.

X-59↗

NASA NTRS2022

Comparison of Two Statistical Models for Low Boom Dose-response Relationships with Correlated Responses

This study compares two statistical models to construct summary dose-response curves for low boom community noise surveys. Data from two NASA field surveys are used that consist of multiple responses per survey participant. These data require an approach that accounts for the correlation among repeated annoyance observations from the same participant. A multilevel model accounts for the correlation by allowing estimated parameters to vary with each survey participant. On the other hand, a population average model utilizes generalized estimating equations and accounts for the correlation via a userspecified within-subject correlation structure. A visual comparison of the dose-response curves for these two methods reveals similar results. When comparing specific points along the summary curves, the multilevel model yields more precise confidence bounds than the population average model. The similarity between the summary curves derived from each model lends validity to both approaches for approximating a population representative summary curve, though modeling assumptions may lend favor to the multilevel logistic modeling approach over the population average model.

dose-response↗

NASA NTRS1997

An Assessment of the Regional Distribution of the Oxygen-Isotope Ratio in Northeastern Canada

A compilation of mean values of the oxygen-isotope ratio relative to standard mean ocean Water for 22 sites representative of conditions in north-eastern Canada is complemented with data on mean annual surface temperature, latitude, surface elevation, and mean annual shortest distance to open ocean denoted by the 10% sea-ice concentration boundary. Stepwise regression analysis is used to develop a multivariate model suitable to infer the distribution of 6 1"0 in an area of complex topography and possibly mixed source of advected water vapor. The best model is produced by a run in the backward mode at the 95% confidence level in which only temperature, latitude and distance to the open ocean remain in the model (the correlation coefficient is 0.915, the adjusted coefficient of determination is 0.809, the root mean square residual is 1.62). This model is similar to the best 6180 predictive model derived elsewhere for Greenland, suggesting a common principal source of advected moisture.

Giovinetto, Mario B.↗

NASA NTRS2015

Reinforcement Learning with Autonomous Small Unmanned Aerial Vehicles in Cluttered Environments

We present ongoing work in the Autonomy Incubator at NASA Langley Research Center (LaRC) exploring the efficacy of a data set aggregation approach to reinforcement learning for small unmanned aerial vehicle (sUAV) flight in dense and cluttered environments with reactive obstacle avoidance. The goal is to learn an autonomous flight model using training experiences from a human piloting a sUAV around static obstacles. The training approach uses video data from a forward-facing camera that records the human pilot's flight. Various computer vision based features are extracted from the video relating to edge and gradient information. The recorded human-controlled inputs are used to train an autonomous control model that correlates the extracted feature vector to a yaw command. As part of the reinforcement learning approach, the autonomous control model is iteratively updated with feedback from a human agent who corrects undesired model output. This data driven approach to autonomous obstacle avoidance is explored for simulated forest environments furthering autonomous flight under the tree canopy research. This enables flight in previously inaccessible environments which are of interest to NASA researchers in Earth and Atmospheric sciences.

Tran, Loc↗

NASA NTRS2023

Can Remotely Sensed Snow Disappearance Explain Seasonal Water Supply?

Understanding the relationship between remotely sensed snow disappearance and seasonal water supply may become vital in coming years to supplement limited ground based, in situ measurements of snow in a changing climate. For the period 2001–2019, we investigated the relationship between satellite derived Day of Snow Disappearance (DSD)—the date at which snow has completely disappeared—and the seasonal water supply, i.e., the April—July total streamflow volume, for 15 snow dominated basins across the western U.S. A Monte Carlo framework was applied, using linear regression models to evaluate the predictive skill—defined here as a model’s ability to accurately predict seasonal flow volumes—of varied predictors, including DSD and in situ snow water equivalent (SWE), across a range of spring forecast dates. In all basins there is a statistically significant relationship between mean DSD and seasonal water supply (p ≤ 0.05), with mean DSD explaining roughly half of the variance. Satellite-based model skill improves later in the forecast season, surpassing the skill of in-situ-based (SWE) models in skill in 10 of the 15 basins by the latest forecast date. We found little to no correlation between model error and basin characteristics such as elevation and the ratio of snow water equivalent to total precipitation. Despite a relatively short data record, this exploratory analysis shows promise for improving seasonal water supply prediction, in particular for snow dominated basins lacking in situ observations.

snow remote sensing↗

NASA NTRS1992

On testing models for the pressure-strain correlation of turbulence using direct simulations

Direct simulations of homogeneous turbulence have, in recent years, come into widespread use for the evaluation of models for the pressure-strain correlation of turbulence. While work in this area has been beneficial, the increasingly common practice of testing the slow and rapid parts of these models separately in uniformly strained turbulent flows is shown in this paper to be unsound. For such flows, the decomposition of models for the total pressure-strain correlation into slow and rapid parts is ambiguous. Consequently, when tested in this manner, misleading conclusions can be drawn about the performance of pressure-strain models. This point is amplified by illustrative calculations of homogeneous shear flow where other pitfalls in the evaluation of models are also uncovered. More meaningful measures for testing the performance of pressure-strain models in uniformly strained turbulent flows are proposed and the implications for turbulence modeling are discussed.

Speziale, Charles G.↗

NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

NASA NTRSDate not supplied

Evaluation of Composite Airframe Dynamic Impact Modeling Using Hawker 4000 Fuselage Drop Test Data

Two drop tests of partial Hawker 4000 fuselage sections were conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to characterize the response of representative composite aerospace structure to dynamic impact loads. Test conditions were selected to induce damage into the composite structure in order to study material failure within a composite fuselage and evaluate the capability of finite element (FE) model analysis to predict that failure. The tests were simulated using FE models which were generated to isolate the effect of developmental data availability on predictive capability. FE Models of the tested fuselage sections were generated using two limited data sets. The first model configuration was reverse engineered from the test article with no information related to design or fabrication details which would be known only by the manufacturer. The second model was generated from data provided by the manufacturer but without additional material characterization test data. Models were developed using these methodologies for both fuselage sections tested. Correlation of each model to the tests conducted was evaluated in terms of damage, deformation, and cabin acceleration measurements. Correlation between the developed models and the tested fuselage sections showed that the reverse engineered model predicted the composite damage and cabin acceleration measured during test though it was limited due to lack of detail in the composite layup changes through the structure. The model developed using manufacturer specifications did not predict damage, due to limited material and component model characterization data, but it did predict acceleration on par with the reverse engineered model. Model capability and limitation sources identified were verified through correlation of a final model which was developed by combining the individual data sets. The combined model demonstrated that the addition of calibrated composite material models to accurate composite layup definitions and detailed geometry led to improved correlation of damage and acceleration response within the composite fuselage structures.

Crashworthiness↗

NASA NTRS2001

Traveling-Wave Tube Amplifier Model to Predict High-Order Modulation Intersymbol Interference

Demands for increased data rates in satellite communications necessitate higher order modulation schemes, larger system bandwidth, and minimum distortion of the modulated signal as it is passed through the traveling wave tube amplifier (TWTA). One type of distortion that the TWTA contributes to is intersymbol interference (ISI), and this becomes particularly disruptive with wide-band, complex modulation schemes. It is suspected that in addition to the dispersion of the TWT, frequency dependent reflections due to mismatches within the TWT are a significant contributor to ISI. To experimentally investigate the effect of these mismatches within the physical TWT on ISI would be prohibitively expensive, as it would require manufacturing numerous amplifiers in addition to the acquisition of the required digital hardware. In an attempt to develop a more accurate model to correlate IS1 with the TWTA and the operational signal, a fully three-dimensional (3D), time-dependent, TWT interaction model has been developed using the electromagnetic particle-in-cell (PIC) code MAFIA (solution of Maxwell's equations by the Finite-Integration-Algorithm). The model includes a user defined slow-wave circuit with a spatially tapered region of loss to implement a sever, and spatially varied geometry (such as helical pitch) to implement a phase velocity taper. The model also includes user defined input/output coupling and an electron beam contained by solenoidal, electrostatic, or periodic permanent magnet (PPM) focusing allowing standard or novel TWTs to be investigated. This model comprehensively takes into account the effects of frequency dependent nonlinear distortions (MAM and AMPM); gain ripple due to frequency dependent reflections at the input/output coupling, severs, and mismatches from dynamic pitch variations; drive induced oscillations; harmonic generation; intermodulation products; and backward waves.

Kory, Carol L.↗

NASA NTRS2012

Advanced Stirling Radioisotope Generator Thermal Power Model in Thermal Desktop SINDA/FLUINT Analyzer

This paper presents a three-dimensional Advanced Stirling Radioisotope Generator (ASRG) thermal power model that was built using the Thermal Desktop SINDA/FLUINT thermal analyzer. The model was correlated with ASRG engineering unit (EU) test data and ASRG flight unit predictions from Lockheed Martin's Ideas TMG thermal model. ASRG performance under (1) ASC hot-end temperatures, (2) ambient temperatures, and (3) years of mission for the general purpose heat source fuel decay was predicted using this model for the flight unit. The results were compared with those reported by Lockheed Martin and showed good agreement. In addition, the model was used to study the performance of the ASRG flight unit for operations on the ground and on the surface of Titan, and the concept of using gold film to reduce thermal loss through insulation was investigated.

Wang, Xiao-Yen↗

NASA NTRS2023

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗

NASA NTRS2023

Hybrid CFD Engineering Model of Plume Induced Erosion and Crater Formation During Descent of Lunar Landers

With rapidly increased worldwide interest in landing on the moon, the issue of Plume Surface Interactions (PSI) is gaining attention. Hazards posed by lander plume induced dust and debris, as well as landing site deformation can be mitigated when better understood through predictive simulations. As simulation enabling computational power continues to increase, hybrid Computational Fluid Dynamics (CFD)/Engineering models provide the immediate ability to conduct parametric/trade studies driving design decisions for landers. Reduced order erosion engineering models apply correlations of the surface erosion rate to the plume induced surface forces with the correlations anchored to flight observations from Apollo LM landings. The MSFC propulsion fluid dynamics branch has developed such a hybrid model for predicting the plume induced viscous erosive regression of the Lunar surface beneath a landing vehicle. The (Descent Interpolated Gas Granular Erosion Model) DIGGEM was originally implemented as a post processing tool to calculate induced erosion rates through vehicle descent using CFD solutions of the vehicle plume at several fixed altitudes. This capability has since been advanced in the Loci/Chem-DIGGEM model to allow transient, moving vehicle, fully coupled viscous erosion modeling of vehicle descent PSI. This model has recently been used to make preflight predictions of the erosive regression of the ground beneath a Commercial Lunar Payload Services (CLPS) vehicle in support of measurements to be made by the Stereo Cameras for Lunar Plume Surface Studies (SCALPSS) instrument.

Plume Surface Interaction↗

NASA NTRS1984

Hoop/column antenna RF verification model. Volume 2: Analysis and correlation

As part of the Large Space System Technology Program, the theoretical and experimental results of the RF characteristic of a hoop/column, quad aperture antenna using an RF verification model are presented. To satisfy the primary purposes of the model, experimental pattern data is provided for the quad aperture configuration at different reflector edge illumination levels, from which the geometry and edge effects can be assessed, and experimental data which can be compared with calculations using various theoretical reflector scattering formulae are provided. It also experimentally determines the effects upon secondary patterns of scale model quartz cables, as used in the hoop/column design, upon secondary patterns in order to assess the importance of developing a scattering theory to predict such effects. In addition, a comprehensive theoretical study and the experimental pattern results of quad aperture antenna feeds, a discussion of the fundamental affect of parasitic side lobes, their amplitude, and location in space.

Croswell, W. F.↗

NASA NTRS1996

Quantifying the Correlation Between Eye-Movement and Perceptual Responses to Moving Plaids

To determine the extent to which the pursuit eye-movement and perceptual systems share a common neural motion-processing pathway, we simultaneously measure the psychophysical and eye-movement responses to drifting plaids in a direction-discrimination task. Correlation between the noise in the eye movements and percepts would suggest a shared neural substrate. Three observers were asked to track a plaid (Type I 90 deg; TF = 4 Hz, SF = 0.6 c/d; direction = -2, 0, or 2 deg), and to respond whether the motion was to the right or left of vertical. The eye-movement direction is computed from the initial 300 ms of saccade-free tracking (near open-loop). On each trial, we use the eye-movement direction to predict the perceptual response. We then compute the probability of successfully predicting the observer's response. We also use SOC analysis as an alternate measure of the correlation. We compare the data from both these analyses to the predictions of two models in which the eye movements and the percept are driven by either a common noisy signal (correlated model) or by two separate noisy signals (uncorrelated model). We also allow for the fact that our measured eye movements are degraded by eye-tracker noise. This noise causes our measured correlation to be lower than the actual biological correlation. The correlations in our data are higher than those predicted by the uncorrelated model, and are similar to the predictions of the correlated model. The proportion of perceptual responses correctly predicted by the eye movements were 0.66, 0.60, 0.73 for the -2, 0, 2 deg stimuli respectively (correlated model 0.65, 0.60, 0.70; uncorrelated model 0.58, 0.51, 0.60).The SOC proportions were 0.71, 0.64, 0.72 (correlated model 0.66, 0.64, 0.69; uncorrelated model 0.5, 0.5, 0.5). These results show that the oculomotor and perceptual system share a performance-limiting noise source and provide strong evidence that a common neural mechanism (perhaps MT or MST) drives both perception and smooth eye movements.

Beutter, Brent R.↗

NASA NTRS1972

Basic failure mechanisms in advanced composites

Failure mechanisms in carbon-epoxy composites are identified as a basis for more reliable prediction of the performance of these materials. The approach involves both the study of local fracture events in model specimens containing small groups of filaments and fractographic examination of high fiber content engineering composites. Emphasis is placed on the correlation of model specimen observations with gross fracture modes. The effects of fiber surface treatment, resin modification and fiber content are studied and acoustic emission methods are applied. Some effort is devoted to analysis of the failure process in composite/metal specimens.

Mullin, J. V.↗

NASA NTRS1987

AH-64A shake test and correlation with NASTRAN finite element model predictions

A NASTRAN FEM code for the AH-64A helicopter airframe has been evaluated in light of suspended-fuselage shake tests that determined this aircraft's frequency-response characteristics at numerous measurement locations throughout the structure. Natural frequencies and mode shapes have been estimated from frequency-response data. On the basis of the correlation study results obtained, several modifications were made to the FEM model, yielding significant performance improvements.

Toossi, Mostafa↗