Search NASA⌕ Search

SEARCH · Search NASA

Results for “fans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Commercial Supersonic Fan Noise Modeling

This presentation describes the development of an empirical noise model for a two-stage fan designed for a supersonic commercial aircraft. The existing fan noise models are reviewed and compared with noise data from a wind tunnel experiment where a model scale two-stage fan was tested. An error metric was developed to quantify how well the measurements and empirical model match. This error metric was then used to determine new coefficients and parameters for a version of the fan model that is a good match for the experimental data.

supersonics, acoustics, turbofan↗
NASA NTRSDate not supplied

Full Stall Simulations of a Redesigned Ventilation Fan for the ISS

The concept of a stall is studied rigorously in the aerospace industry. From a design standpoint, instabilities such as stall are undesirable– operation in the stall regime has a tremendous impact on aerodynamic performance as well as structural integrity. In extreme cases, operating in stall conditions can cause failure. Further, stall can cause a loss of lift on aircraft wings or a loss of thrust in aircraft engines. In any case, stall continues to be a topic of interest in the aerospace industry. The present work aims to analyze the stall characteristics of a ventilation fan that was recently designed for the International Space Station (ISS). Although the ventilation fan has a rotor-stator design, this paper considers a rotor-only configuration. The FUN3D Computational Fluid Dynamic (CFD) solver developed by NASA Langley Research Center was used to simulate the operational characteristics of the ventilation fan. FUN3D solves the Unsteady Reynolds-Averaged Naiver-Stokes (URANS) equations using implicit time marching and a dynamic overset grid. The FUN3D solver was originally written for exterior flow fields; however, this work represents an extension of the FUN3D solver to turbomachinery or interior flow fields. The FUN3D results for the rotor-only ventilation fan accurately captured the operational characteristics inherent to compressors– the results shared similar performance trends when compared to the experimental results for the rotor-stator case. A peak adiabatic efficiency of 96% occurred at a MFR of 105.2 CFM, the minimum aerodynamically stable point. A computationally stable stall occurred at a mass flow rate of 43.8 CFM where the adiabatic efficiency dropped to 69%.

CFD↗
NASA NTRS2017

Dynamic Analysis for a Geared Turbofan Engine with Variable Area Fan Nozzle

Aggressive design goals have been set for future aero-propulsion systems with regards to fuel economy, noise, and emissions. To meet these challenging goals, advanced propulsion concepts are being explored and current operating margins are being re-evaluated to find additional concessions that can be made. One advanced propulsion concept being evaluated is a geared turbofan with a variable area fan nozzle (VAFN), developed by NASA. This engine features a small core, a fan driven by the low pressure turbine through a reduction gearbox, and a shape memory alloy (SMA)-actuated VAFN. The VAFN is designed to allow both a small exit area for efficient operation at cruise, while being able to open wider at high power conditions to reduce backpressure on the fan and ensure a safe level of stall margin is maintained. The VAFN is actuated via a SMA-based system instead of a conventional system to decrease overall weight of the system, however, SMA-based actuators respond relatively slowly, which introduces dynamic issues that are investigated in this work. This paper describes both a control system designed specifically for issues associated with SMAs, and dynamic analysis of the geared turbofan VAFN with the SMA actuators. Also, some future recommendations are provided for this type of propulsion system.

N+3↗
NASA NTRS2017

Multipurpose Rotating Rake Arrays for Integrated Inlet and Fan Stage Performance Measurement

Low-pressure-ratio fan stage performance measurement requires precise measurement of conditions upstream and downstream of the fan stage. This presentation will discuss the rotating rake arrays used for the recent Boundary Layer Ingesting Inlet-Distortion-Tolerant Fan experiment in the NASA Glenn 8 by 6 foot wind tunnel. To achieve precise measurements, simulations of the rake sampling from pre-test CFD (Computerized Fluid Dynamics) solutions were used to optimize the number and locations of rake instruments.

performanc↗
NASA NTRS2018

Cyclic Symmetry Finite Element Forced Response Analysis of a Distortion-Tolerant Fan with Boundary Layer Ingestion

Accurate prediction of the blade vibration stress is required to determine overall durability of fan blade design under Boundary Layer Ingestion (BLI) distorted flow environments. Traditional single blade modeling technique is incapable of representing accurate modeling for the entire rotor blade system subject to complex dynamic loading behaviors and vibrations in distorted flow conditions. A particular objective of our work was to develop a high-fidelity full-rotor aeromechanics analysis capability for a system subjected to a distorted inlet flow by applying cyclic symmetry finite element modeling methodology. This reduction modeling method allows computationally very efficient analysis using a small periodic section of the full rotor blade system. Experimental testing by the use of the 8-foot by 6-foot Supersonic Wind Tunnel Test facility at NASA Glenn Research Center was also carried out for the system designated as the Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan (BLI2DTF) technology development. The results obtained from the present numerical modeling technique were evaluated with those of the wind tunnel experimental test, toward establishing a computationally efficient aeromechanics analysis modeling tool facilitating for analyses of the full rotor blade systems subjected to a distorted inlet flow conditions. Fairly good correlations were achieved hence our computational modeling techniques were fully demonstrated. The analysis result showed that the safety margin requirement set in the BLI2DTF fan blade design provided a sufficient margin with respect to the operating speed range.

forced response analysis↗
DOE OSTI2024

Primary Pump Motor Area - Transfer Fan Replacement PLC Design

My poster is about a project that I have worked on in my time at ATR as an intern. The Heating and Ventilation Control Panel (HVB-1) controls thirty-five heating and ventilation fans within the Advanced Test Reactor. This control panel needs replacement, as many of the components inside the existing panel are becoming old and degrading. In preparation for this replacement effort, concepts and component identification for the new control panel needed to be developed. Instead of replacing the new panel with replacement mechanical components, a Programmable Logic Controller (PLC) is proposed as a solution. Although multiple fans are associated with this panel, my poster focuses on the replacement design for the Primary Pump Motor Area Transfer Fan. This will provide an example of how the entire cabinet may be upgraded.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1971

Aerodynamics of lift fan V/STOL aircraft

V/stol aircraft lift fan aerodynamics, discussing optimum fan pressure ratios, augmentation ratio, noise constraints, wing loading and fan configurations

Hall, L. P.↗
NASA NTRS1972

Noise generated by quiet engine fans. 1: FanB

Acoustical tests of full scale fans for jet engines are presented. The fans are described and some aerodynamic operating data are given. Far field noise around the fan was measured for a variety of configurations over a range of operating conditions. Complete results of one third octave band analysis are presented in tabular form. Power spectra and sideline perceived noise levels are included.

Montegani, F. J.↗
NASA NTRS1972

High-loading low-speed fan study. 4: Data and performance with redesign stator and including a rotor tip casing treatment

A single stage fan with a rotor tip speed of 1000 ft/sec(304.8 m/sec) and a hub-to-tip ratio of 0.392 was retested with a redesigned stator. Tests were conducted with uniform inlet, tip-radial, hub-radial, and circumferential inlet distortions. With uniform inlet flow, stall margin was improved 12 percentage points above that with the original stator. The fan demonstrated an efficiency of 0.883 and a stall margin of 15 percent at a pressure ratio of 1.488 and a specific flow of 41.17 lb/sec/sq ft. Tests were also made with a redesigned casing treatment consisting of skewed slots over the rotor blade tips. This casing treatment gave a 7 percentage point improvement in stall margin when tested with tip radial distortion (when the rotor tip initiated stall). Noise measurements at the fan inlet and exit indicate no effect from closing the stator 10 degrees, nor were there measurable effects from adding skewed slots over the blade tips.

Harley, K. G.↗
NASA NTRS1972

Low pressure ratio fan noise experiment and theory.

Evaluation of data obtained from noise measurements on a wind-tunnel model of a Q-FAN, a new low-pressure-ratio, low-noise propulsion system. It is found that both rotor blades and stator vanes contributed to the noise signature of the test fan. Tone noise at blade passage frequency and at the high harmonics of blade passage frequency was the result of unsteady inflow to the fan. Tone noise at twice blade passage frequency and several high harmonics resulted from interception of rotor blade wakes by the stators. The midfrequency broadband noise also resulted from interception of wakes by the stators. Rotor vortex noise contributed only at high frequencies where the level of stator broadband decayed.

Metzger, F. B.↗
NASA NTRS1972

Design studies of lift fan engines suitable for use in civilian VTOL aircraft.

Preliminary engine design studies have been made of two general types of low-pressure-ratio lift fan engines that are receiving increasing attention as a means to provide low-speed lift for large civilian VTOL transports. The two engine types are integral fans and remote powered fans. A portion of the results of these design studies is summarized, including the crucial engine requirements, and some of the characteristics of the emerging engine designs of each type.

Roelke, R. J.↗
NASA NTRS1973

Preliminary study of an integral fan lift/cruise engine for a 100 passenger VTOL transport

A simplified mission analysis was performed to determine an optimum engine cycle for a 100-passenger VTOL transport with a range of 500 statute miles. The aircraft had a total of eight integral fan lift engines, three of which serve as cruise engines. Fan pressure ratio was varied from 1.2 to 1.3, overall pressure ratio from 7 to 13, and turbine inlet temperature from 2460 to 2860 R. Bypass ratio was selected to meet a 500-foot altitude flyover noise goal of 95 PNdB. Airplane gross weight and direct operating cost (DOC) were calculated. The lowest DOC of 1.82 cents per seat-mile was achieved with a fan pressure ratio of 1.3, overall pressure ratio of 12, and turbine inlet temperature of 2860 R.

Civinskas, K. C.↗
NASA NTRS1973

High loading, low speed fan study, 5

A low speed, low noise, single stage fan was designed and tested. Design pressure ratio was 1.5 at a rotor tip speed of 1000 ft/sec. No inlet guide vane was used, the rotor stator was spaced and the number of rotor and stator airfoils was selected for low noise. Tests were conducted with uniform and distorted inlet flows. Stall margin of the initial design was too low for practical application. Airfoil slots and boundary layer and endwall devices did not improve stall margin sufficiently. A redesigned stator with reduced loadings increased stall margin, giving a fan efficiency of 0.883, 15% stall margin, and a 1.474 pressure radio at a specific flow of 41.7 lb/sec sq ft. Casing treatment over rotor tips improved stall margin with distorted inlet flow; vortex generators did not. Blade passing frequency noise increased with rotor relative Mach number. No supersonic fan noise was measured below 105% of design speed. Slotting airfoils, casing treatments, and a reduction of the ratio (number-stators/number-rotors) from (2n + 16) to (2n + 2) had no significant effects on noise.

Keenan, M. J.↗
NASA NTRS1973

Steady state analysis of Energy Transfer Control (ETC) and compressor bleed concepts of remote lift fan control

Two new concepts of control for VTOL aircraft remote lift fans are analyzed and discussed. Both concepts employ flow transfer among lift fans located in separate parts of the aircraft in order to obtain attitude control moments in hover and low-speed flight. The results presented are from a digital computer analysis of the YJ97/LF460 remote drive turbofan, although qualitative conclusions should apply to any remote fan system. The basic operating principles of the two systems are described, and their steady-state moment generating capabilities are discussed. Lift-recovery strategies for component failures are also analyzed.

Sellers, J. F.↗
NASA NTRS1973

Noise measurements from a large-scale lift fan transport in the 40- by 80-foot wind tunnel

Noise data measurements from a large scale lift fan transport model aircraft were made in the 40- by 80-foot wind tunnel. The model had two lift fans in deep inlets in the forward fuselage and two lift-cruise fans in pods on the aft fuselage. The noise data measurements are presented as listings and plots of sounds pressure level versus 1/3-octave center frequency.

Atencio, A., Jr.↗
NASA NTRS1973

Shrouded fan propulsors for light aircraft.

Continued growth of general-aviation over the next 10-15 years is dependent upon continuing improvement in aircraft safety, utility, performance, and cost. An attractive, compact, low-noise propulsor concept, the Q-FAN, when matched to reciprocating or rotary combustion engines, opens up the exciting prospect of new, cleaner airframe designs for the next generation of general-aviation aircraft, which will provide these improvements and meet the expected noise and pollution restrictions of the 1980 time period. In this paper, Q-FAN propulsion system performance, weight, noise, and cost trends are discussed. The impact of this propulsion system on the complete aircraft is investigated for two representative aircraft size categories. Examples of conceptual designs for Q-FAN/engine integration and aircraft installations are presented.

Waters, M. H.↗
NASA NTRS1973

Remote lift fan study program, volume 4

A study program to select and conduct preliminary design of advanced technology lift fan systems to meet low noise goals of future V/STOL transport aircraft is discussed. This volume contains results of additional studies conducted to support the main preliminary design effort done under the Remote Lift Fan Study Program (Contract NAS3-14406) and a companion effort, the Integral Lift Fan Study (NAS3-14404). These results cover engine emission study, a review of existing engines for research aircraft application and support data for aircraft studies.

Source record↗