Search NASA⌕ Search

SEARCH · Search NASA

Results for “fixed points”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Mach 4 Performance of a Fixed-Geometry Hypersonic Inlet with Rectangular-to-Elliptical Shape Transition

Wind-tunnel testing of a hypersonic inlet with rectangular-to-elliptical shape transition has been conducted at Mach 4.0. These tests were performed to investigate the starting and back-pressure limits of this fixed-geometry inlet at conditions well below the Mach 5.7 design point. Results showed that the inlet required side spillage holes in order to self-start at Mach 4.0. Once started, the inlet generated a compression ratio of 12.6, captured almost 80% of available air and withstood a back-pressure ratio of 30.3 relative to tunnel static pressure. The spillage penalty for self-starting was estimated to be 4% of available air. These experimental results, along with previous experimental results at Mach 6.2 indicate that fixed-geometry inlets with rectangular-to-elliptical shape transition are a viable configuration for airframe-integrated scramjets that operate over a significant Mach number range. Nomenclature

Smart, Michael K.↗
NASA NTRS2005

Sensors for Pointing Moving Instruments Toward Each Other

Optoelectronic sensor systems are being developed for use in maintaining fixed relative orientations of two scientific-instrument platforms that are in relative motion. In the original intended application, the platforms would be two spacecraft flying in formation and separated by a long baseline. In principle, sensor systems of this type could also be used in terrestrial applications for maintaining alignments between moving instrument platforms. The sensor system would utilize beacon laser beams that would be transmitted by the platforms in the normal course of scientific measurements. The frequency of the returned laser beam would differ by about 5 MHz. On each platform, the transmitted laser beam and the laser beam bounced off the other platform would be focused onto a quadrant photodetector, where the interference between the laser beams would give rise to sinusoidal (beat-frequency) signals on all four quadrants. The differences among the phases of the beat-frequency signals in the quadrants would depend on, and would be used to determine the angle between, the wave fronts of the outgoing and incoming laser beams.

Liebe, Carl↗
NASA NTRS1977

Interpolation schemes for orbit determination with the global positioning system

This paper demonstrates that the Global Positioning System (GPS) and simple interpolation schemes can be utilized to satisfy typical orbit determination demands of applications satellites. The complete GPS consists of 24 satellites and permits a position fix of a user satellite at any arbitrary instant. The interpolation formulae used in this report fit generalized Keplerian orbits through a number of position fixes. For a given accuracy level the telemetry requirements as measured by the time intervals between position fixes and the computational load of an interpolation as measured by the number of points through which a generalized Keplerian orbit is fitted vary inversely. A set of possible compromises between these two factors is presented. The Phase I GPS consists of 6 satellites and permits a position fix of a user satellite just 36% of the time. It is shown that with this system more sophisticated interpolation schemes which model atmospheric drag and higher degree terms of the earth's gravity field must be employed to obtain accurate orbits.

Argentiero, P.↗
NASA NTRS2018

Recent Advances to Estimation of Fixed-Interface Modal Models Using Dynamic Substructuring

In 2010, Allen & Mayes proposed to estimate the fixed-interface modes of a structure by measuring the modes of the structure bolted to a fixture and then applying constraints to the fixture using the transmission simulator method. While the method proved useful, and has indeed been used in studies since that point, a few peculiarities were noted. First, in some cases the estimated fixed-base natural frequencies were observed to converge very slowly to the true values (in simulated experiments) as the number of constraints was increased. To formulate these constraints, prior studies used only the free-interface modes of the fixture or the measured modes of the assembly. This work extends that to consider other sets of constraints, showing improved results. Furthermore, in some prior studies it has been observed that there were errors of more than 10% in the natural frequencies even when the fixture motion was hundreds of times smaller than the motion of the structure of interest (and so it had presumably been removed). This work explores this phenomenon, seeking to use the strain energy in the fixture, to the extent that it can be estimated using a test-analysis model for the fixture, as a metric to predict frequency error. The proposed methods are explored by applying them to simulated measurements from a beam and from the NASA Space Launch System coupled to the Mobile Launcher.

Allen, Mathew S.↗
NASA NTRS1970

Global search algorithm for optimal control

Random-search algorithm employs local and global properties to solve two-point boundary value problem in Pontryagin maximum principle for either fixed or variable end-time problems. Mixed boundary value problem is transformed to an initial value problem. Mapping between initial and terminal values utilizes hybrid computer.

Brocker, D. H.↗
NASA NTRS1983

The disturbance flow field produced by an evolving vortex

The flow field of a vortex in a viscous shear flow is found by constructing a uniformly valid asymptotic expansion consisting of an inner solution field represented, to lowest order, by a two dimensional, nonliner, inviscid Stuart vortex and an outer solution field represented, to lowest order, by either a two dimensional parallel or self similar viscous flow. The technique involves scaling both the transverse and streamwise coordinates in the vicinity of the vortex as well as allowing for a slow variation of the outer viscous flow. Criteria are established for both the size of the vortical structure and proximity to the boundary surfaces. The composite solution is a consistent mathematical picture of the flow field at a fixed streamwise location as the vortical structure evolves past this point. Such a formulation is also useful in the specification of boundary or initial conditions in numerical fluid dynamic calculations, where an inconsistent setting of these conditions leads to spurious results for rather long computation times.

Gatski, T. B.↗
NASA NTRS2001

Demonstration of Imaging Fourier Transform Spectrometer (FTS) Performance for Planetary and Geostationary Earth Observing

The combination of massively parallel spatial sampling and accurate spectral radiometry offered by imaging FTS makes it extremely attractive for earth and planetary remote sensing. We constructed a breadboard instrument to help assess the potential for planetary applications of small imaging FTS instruments in the 1 - 5 micrometer range. The results also support definition of the NASA Geostationary Imaging FTS (GIFTS) instrument that will make key meteorological and climate observations from geostationary earth orbit. The Planetary Imaging FTS (PIFTS) breadboard is based on a custom miniaturized Bomen interferometer that uses corner cube reflectors, a wishbone pivoting voice-coil delay scan mechanism, and a laser diode metrology system. The interferometer optical output is measured by a commercial infrared camera procured from Santa Barbara Focalplane. It uses an InSb 128x128 detector array that covers the entire FOV of the instrument when coupled with a 25 mm focal length commercial camera lens. With appropriate lenses and cold filters the instrument can be used from the visible to 5 micrometers. The delay scan is continuous, but slow, covering the maximum range of +/- 0.4 cm in 37.56 sec at a rate of 500 image frames per second. Image exposures are timed to be centered around predicted zero crossings. The design allows for prediction algorithms that account for the most recent fringe rate so that timing jitter produced by scan speed variations can be minimized. Response to a fixed source is linear with exposure time nearly to the point of saturation. Linearity with respect to input variations was demonstrated to within 0.16% using a 3-point blackbody calibration. Imaging of external complex scenes was carried out at low and high spectral resolution. These require full complex calibration to remove background contributions that vary dramatically over the instrument FOV. Testing is continuing to demonstrate the precise radiometric accuracy and noise characteristics.

Revercomb, Henry E.↗
NASA NTRS1947

Effects of Compressibility on the Flow Past Thick Airfoil Sections

Six, 3-inch-chord symmetrical airfoil sections having systematic variations in thickness and thickness location were tested at Mach numbers near flight values for propeller-shank sections. The tests, the results of which are presented in the form of schlieren photographs of the flow past each model and pressure-distribution charts for two of the model, were performed to illustrate the effects of compressibility on the flow past thick symmetrical airfoil sections. Representative flow photographs indicated that at Mach numbers approximately 0.05 above the critical Mach number a speed region was reached in which the flow oscillated rapidly and the separation point and the location of the shock wave were unstable. Fixing the transition on both surfaces of the airfoil was effective in reducing these rapid oscillations. The pressure distributions showed that the section normal-force coefficients for thick airfoils were very erratic at subcritical speeds; at supercritical speeds the section normal-force coefficients for the thick airfoils became more regular. Drag coefficients showed that considerable drag decreases can be expected by decreasing the model thickness ratio.

Daley, Bernard N.↗
NASA NTRS2017

Flight Deck Surface Trajectory-Based Operations (STBO): A Four-Dimensional Trajectory (4DT) Simulation

In four-dimensional trajectory (4DT) Surface Trajectory-Based Operations (STBO), aircraft are assigned a conflict-free 4DT which defines an expected location (x,y coordinates) at all times, t, along the taxi route (with altitude, being fixed). These 4DTs afford the highest temporal certainty at all points along the taxi route, and at the departure runway. In the present study, a 4DT flight deck display was presented on the Airport Moving Map (AMM) to support pilot conformance to a 4DT clearance while taxiing under manual control. This pilot-in-the-loop simulation compared the effect of 4DT flight deck display formats on distance from the expected 4DT location, conformance to the displayed tolerance band, eyes-out time, and pilot ratings of safety and workload. In the defined-tolerance display format, a graphical representation of the expected 4DT location, with a distance-based allowable-tolerance band, was depicted on the AMM. Two defined-tolerance band sizes were tested: plus or minus 164 feet and plus or minus 405 feet. In the undefined-tolerance display format, the expected 4DT location was displayed graphically on the AMM, with no indicated allowable-tolerance bounds. Each taxi trial included 4DT speed changes (two or five, per trial) and a range of 4DT taxi speeds. Results showed that the larger (plus or minus 405 feet) defined-tolerance band yielded higher conformance levels than the smaller (plus or minus 164 feet) band, with pilots staying within the specified and displayed conformance bounds more in the larger (99.71%) than the smaller defined-tolerance band (93.37 percent). However, in terms of being able to predict the location of the aircraft compared to the expected 4DT location, the smaller defined-tolerance band resulted in pilots keeping their aircraft closer to the 4DT location, for both average distance and for a given confidence interval (e.g., 95 percent), than either the larger defined-tolerance band or the undefined-tolerance display format. The larger tolerance band yielded more “eyes-out-the-window” time than the smaller tolerance band. Pilots also rated taxing with the larger tolerance band as safer than the smaller tolerance band.

STBO↗
NASA NTRS1993

Further studies to extend and test the area-time-integral technique applied to satellite data

The principal goal of this project is to establish relationships that would allow application of area-time integral (ATI) calculations based upon satellite data to estimate rainfall volumes. The research has been pursued using two different approaches, which for convenience can be designated as the 'fixed-threshold approach' and the 'variable-threshold approach'. In the former approach, an attempt is made to determine a single temperature threshold in the satellite infrared data that would yield ATI values for identifiable cloud clusters which are most closely related to the corresponding rainfall amounts. Results thus far have indicated that a strong correlation exists between the rain volumes and the satellite ATI values, but the optimum threshold for this relationship seems to differ from one geographic location to another. The difference is probably related to differences in the basic precipitation mechanisms that dominate in the different regions. The average rainfall rate associated with each cloudy pixel is also found to vary across the spectrum of ATI values. Work on the second, or 'variable-threshold', approach for determining the satellite ATI values was essentially suspended during this period due to exhaustion of project funds. Most of the ATI work thus far has dealt with cloud clusters from the Lagrangian or 'floating-target' point of view. For many purposes, however, the Eulerian or 'fixed-target' perspective is more appropriate. For a very large target area encompassing entire cluster life histories, the rain volume-ATI relationship would obviously be the same in either case. The important question for the Eulerian perspective is how small the fixed area can be made while maintaining consistency in that relationship.

Smith, Paul L.↗
NASA NTRS2010

Mission Enabling and Enhancing Spacecraft Capabilities with MicroNewton Electric Propulsion

The capability to significantly improve current spacecraft pointing, precision orbit maintenance and disturbance mitigation were considered using precision, quiescent microNewton electric propulsion systems. Analysis results showed that electric propulsion systems operating in the microNewton to hundreds of microNewtons thrust range can offer significant improvements over state-of-the-art mission capabilities to enable 30 m Earth-fixed orbital tubes, constellation spacecraft position control to within nanometers and exoplanet observatory pointing with 0.1 milliarcsecond precision. Specific thrust levels and profiles required to support these capabilities are discussed.

micro propulsion↗
NASA NTRS1998

Evaluation of Clouds and the Earth's Radiant Energy System (CERES) Scanner Pointing Accuracy using a Coastline Detection System

Clouds and the Earth's Radiant Energy System (CERES) is a National Aeronautics and Space Administration (NASA) investigation to examine the role of clouds in the radiative energy flow through the Earth-atmosphere system. The first CERES scanning radiometer was launched on November 27, 1997 into a 35 inclination, 350 km altitude orbit, on the Tropical Rainfall Measuring Mission (TRMM) spacecraft. The CERES instrument consists of a three channel scanning broadband radiometer. The spectral bands measure shortwave (0.3 - 5 microns), window (8 - 12 microns), and total (0.3 - 100 microns) radiation reflected or emitted from the Earth-atmosphere system. Each Earth viewing measurement is geolocated to the Earth fixed coordinate system using satellite ephemeris, Earth rotation and geoid, and instrument pointing data. The interactive CERES coastline detection system is used to assess the accuracy of the CERES geolocation process. By analyzing radiative flux gradients at the boundaries of ocean and land masses, the accuracy of the scanner measurement locations may be derived for the CERES/TRMM instrument/satellite system. The resulting CERES measurement location errors are within 10% of the nadir footprint size. Precise pointing knowledge of the Visible and Infrared Scanner (VIRS) is required for convolution of cloud properties onto the CERES footprint; initial VIRS coastline results are included.

Currey, Chris↗
NASA NTRS1980

Backward deletion to minimize prediction errors in models from factorial experiments with zero to six center points

Population model coefficients were chosen to simulate a saturated 2 to the fourth power fixed effects experiment having an unfavorable distribution of relative values. Using random number studies, deletion strategies were compared that were based on the F distribution, on an order statistics distribution of Cochran's, and on a combination of the two. Results of the comparisons and a recommended strategy are given.

Holms, A. G.↗
NASA NTRS2000

Laminar Diffusion Flame Studies (Ground- and Space-Based Studies)

Laminar diffusion flames are of interest because they provide model flame systems that are far more tractable for analysis and experiments than more practical turbulent diffusion flames. Certainly, understanding flame processes within laminar diffusion flames must precede understanding these processes in more complex turbulent diffusion flames. In addition, many properties of laminar diffusion flames are directly relevant to turbulent diffusion flames using laminar flamelet concepts. Laminar jet diffusion flame shapes (luminous flame boundaries) have been of particular interest since the classical study of Burke and Schumann because they are a simple nonintrusive measurement that is convenient for evaluating flame structure predictions. Thus, consideration of laminar flame shapes is undertaken in the following, emphasizing conditions where effects of gravity are small, due to the importance of such conditions to practical applications. Another class of interesting properties of laminar diffusion flames are their laminar soot and smoke point properties (i.e., the flame length, fuel flow rate, characteristic residence time, etc., at the onset of soot appearance in the flame (the soot point) and the onset of soot emissions from the flame (the smoke point)). These are useful observable soot properties of nonpremixed flames because they provide a convenient means to rate several aspects of flame sooting properties: the relative propensity of various fuels to produce soot in flames; the relative effects of fuel structure, fuel dilution, flame temperature and ambient pressure on the soot appearance and emission properties of flames; the relative levels of continuum radiation from soot in flames; and effects of the intrusion of gravity (or buoyant motion) on emissions of soot from flames. An important motivation to define conditions for soot emissions is that observations of laminar jet diffusion flames in critical environments, e.g., space shuttle and space station facilities, cannot involve soot emitting flames in order to ensure that test chamber windows used for experimental observations are not blocked by soot deposits, thereby compromising unusually valuable experimental results. Another important motivation to define conditions where soot is present in diffusion flames is that flame chemistry, transport and radiation properties are vastly simplified when soot is absent, making such flames far more tractable for detailed numerical simulations than corresponding soot-containing flames. Motivated by these observations, the objectives of this phase of the investigation were as follows: (1) Observe flame-sheet shapes (the location of the reaction zone near phi=1) of nonluminous (soot free) laminar jet diffusion flames in both still and coflowing air and use these results to develop simplified models of flame-sheet shapes for these conditions; (2) Observe luminous flame boundaries of luminous (soot-containing) laminar jet diffusion flames in both still and coflowing air and use these results to develop simplified models of luminous flame boundaries for these conditions. In order to fix ideas here, maximum luminous flame boundaries at the laminar smoke point conditions were sought, i.e., luminous flame boundaries at the laminar smoke point; (3) Observe effects of coflow on laminar soot- and smoke-point conditions because coflow has been proposed as a means to control soot emissions and minimize the presence of soot in diffusion flames.

Dai, Z.↗
NASA NTRS1981

Flow separation in shear-layer-driven cavities

A study of the shear-layer flow over a range of open-top cavity configurations is reported. Emphasis is placed on the effect that altering the cavity's span length and aspect ratio has on the development of the shear layer. Computational results are obtained using an interactive method which adapts the compressible boundary-layer model for the flow above the cavity and incompressible Navier-Stokes equations within the enclosure. Interaction of this composite model with the outer, inviscid supersonic flow is also considered in one case. The results show that the location of the stagnation points is sensitive primarily to the variation of the span. When the span was fixed and the aspect ratio varied, the shear layer was nearly unaffected except at aspect ratios less than 0.5. Interaction with the outer flow had a smoothing effect on the shape of the dividing streamline but did not significantly affect the location of the stagnation points.

Brandeis, J.↗
NASA NTRS1979

Design, fabrication and delivery of a prototype saturator for ACPL

The design configuration and performance characteristics of a saturator developed to provide ground-based simulation for some of the experiments for ACPL-1 first flights of Spacelab are described, some difficulties encountered with the apparatus are discussed, and recommendations concerning testing of this type of instrument are presented. The saturators provide a means of accurately fixing the water vapor mixing ratio of an aerosol sample. Dew point temperatures from almost freezing to ambient room temperatures can be attained with high precision. The instruments can accommodate aerosol flow rates approaching 1000 cc/s. Provisions were made to inject aerosols upstream of these saturators, although downstream injection can be accomplished as well. A device of this type will be used in the ACPL-1 to condition various aerosols delivered concurrently to a CFD, expansion chamber, and static diffusion chamber used in zero gravity cloud-forming experiments. The saturator was designed to meet the requirements projected for the flight instrument.

Keyser, G.↗
NASA NTRS1987

Finite element models of wire rope for vibration analysis

The usefulness of wire rope in shock and vibration isolation is briefly reviewed and its modeling for the purpose of vibration analysis is addressed. A model of a nominally straight segment of wire rope is described in which the rope structure is represented by a maiden, or central, strand of wire with one (or more) strand(s) wrapped around it in a helix (helices). The individual strands are modeled using finite elements and MSC NASTRAN. Small linear segments of each wire are modeled mathematically by dividing them lengthwise into triangular prisms representing each prism by a solid NASTRAN element. To model pretensioning and allow for extraction of internal force information from the NASTRAN model, the wound strands are connected to the maiden strand and each other using spring (scalar elastic) elements. Mode shapes for a length of wire rope with one and fixed to a moving base and the other attached to a point mass, are presented. The use of the NASTRAN derived mode shapes to approximate internal normal forces in equations of motion for vibration analyses is considered.

Cochran, J. E., Jr.↗
NASA NTRS1993

Method for controlling protein crystallization

A method and apparatus for controlling the crystallization of protein by solvent evaporation including placing a drop of protein solution between and in contact with a pair of parallel plates and driving one of the plates toward and away from the other plate in a controlled manner to adjust the spacing between the plates is presented. The drop of solution forms a liquid cylinder having a height dependent upon the plate spacing thereby effecting the surface area available for solvent evaporation. When the spacing is close, evaporation is slow. Evaporation is increased by increasing the spacing between the plates until the breaking point of the liquid cylinder. One plate is mounted upon a fixed post while the other plate is carried by a receptacle movable relative to the post and driven by a belt driven screw drive. The temperature and humidity of the drop of protein solution are controlled by sealing the drop within the receptacle and mounting a heater and dessicant within the receptacle.

Noever, David A.↗