Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Low speed aerodynamic characteristics of a transport model having 42.33 deg swept low wing with supercritical airfoil, double-slotted flaps, and T-tail or low tail

A low-speed investigation was conducted in the Langley V/STOL tunnel over an angle-of-attack range of approximately 4 deg to 24 deg to determine the static longitudinal stability characteristics and high lift performance of a general research model which represented an advanced subsonic transport configuration. The model had a 42.33 deg swept, aspect ratio 7.05 wing with a supercritical airfoil and high lift system consisting of a leading edge device (slat or Kruger flap) and a double-slotted flap. The flaps were deflected for take off and landing configurations and were not deflected for tests of the clean configuration. The model was tested with the horizontal tail in either a T tail or low tail position. The effects of various arrangements of flowthrough nacelles which represent a three engine configuration (two large wing-mounted nacelles and a vertical tail mounted nacelle) and a four engine configuration (four smaller wing-mounted nacelles) were determined.

Fournier, P. G.↗
NASA NTRS1975

Use of active control systems to improve bending and rotor flapping response of a tilt rotor VTOL airplane

The results are summarized of an analytical study of the use of active control systems for the purpose of reducing the root mean square response of wing vertical bending and rotor flapping to atmospheric turbulence for a tilt-rotor VTOL airplane. Only the wing/rotor assembly was considered so that results of a wind tunnel test program would be applicable in a subsequent phase of the research. The capabilities and limitations of simple single feedback configurations were identified, and the most promising multiloop feedback configurations were then investigated. Design parameters were selected so as to minimize either wing bending or rotor flapping response. Within the constraints imposed by practical levels of feedback gains and complexity and by considerations of safety, reduction in response due to turbulence of the order of 30 to 50 percent is predicted using the rotor longitudinal cyclic and a trailing edge wing flap as control effectors.

Whitaker, H. P.↗
NASA NTRS1976

Pressure distributions on a rectangular aspect-ratio-6, slotted supercritical airfoil wing with externally blown flaps

An investigation was made in the 5.18 m (17 ft) test section of the Langley 300 MPH 7 by 10 foot tunnel on a rectangular, aspect ratio 6 wing which had a slotted supercritical airfoil section and externally blown flaps. The 13 percent thick wing was fitted with two high lift flap systems: single slotted and double slotted. The designations single slotted and double slotted do not include the slot which exists near the trailing edge of the basic slotted supercritical airfoil. Tests were made over an angle of attack range of -6 deg to 20 deg and a thrust-coefficient range up to 1.94 for a free-stream dynamic pressure of 526.7 Pa (11.0 lb/sq ft). The results of the investigation are presented as curves and tabulations of the chordwise pressure distributions at the midsemispan station for the wing and each flap element.

Johnson, W. G., Jr.↗
NASA NTRS1976

An investigation of flap-lag stability of wind turbine rotors in the presence of velocity gradients and helicopter rotors in forward flight

The flap-lag equations of motion of a torsionally rigid and centrally hinged spring-restrained rigid blade are developed using quasi-steady blade-element aerodynamic theory. These equations have periodic coefficients and are applicable to both wind-turbine rotors with velocity gradients and helicopter rotors in forward flight. By solving these equations both by the Floquet-Liapunov method and by an approximate method, the range of applicability of the latter method is established. Flap-lag and pure flapping stability boundaries illustrating the effects of flow and rotor parameters are presented. Finally, some discussion on the techniques for generating the Floquet transition matrix and on the relative merits of the coordinate axes system is presented.

Kaza, K. R. V.↗
NASA NTRS1976

New developments in blown flap noise technology

The noise technology relating to blown-flap systems is reviewed. There are three general sources of noise: turbomachinery, airframe, and the interaction noise of the jet blowing on the flaps. The latter noise-source area is the most critical and the main subject dicussed. Characteristics of lower surface blown and upper surface blown systems are described, including noise spectra, directivity, jet velocity characteristics, aircraft geometric variation effects, and aircraft forward speed effects. Noise reduction concepts are described, including slowing down the jet flow field by devices and engine cycle modifications, structural geometry and shielding modifications, local flow field modifications of the passive and active type, and the absorption of noise. It is concluded that, while there has been considerable progress in the past several years, low noise characteristics in blown flap aircraft must be largely built in by better application of low noise principles during the design.

Gibson, J. S.↗
NASA NTRS1977

Flap noise and aerodynamic results for model QCSEE over-the-wing configurations

Noise spectra in three dimensions and aerodynamic data were measured for a model of the NASA quiet clean short-haul experimental engine (QCSEE) over-the-wing configuration. The effects of flap length, nozzle exhaust velocity, and nozzle geometry were determined using a single nozzle and wing-flap segment. The scaled-up model data is representative of full scale flap noise with the QCSEE engine.

Olsen, W.↗
NASA NTRS1977

Flight test pilot evaluation of a delayed flap approach procedure

Using NASA's CV-990 aircraft, a delayed flap approach procedure was demonstrated to nine guest pilots from the air transport industry. Four demonstration flights and 37 approaches were conducted under VFR weather conditions. A limited pilot evaluation of the delayed flap procedure was obtained from pilot comments and from questionaires they completed. Pilot acceptability, pilot workload, and ATC compatibility were quantitatively rated. The delayed flap procedure was shown to be feasible, and suggestions for further development work were obtained.

Bull, J. S.↗
NASA NTRS1977

Aileron and Krueger nose flap effectiveness measured on an oblique wing

The effects that deflection of conventional ailerons have on the lateral/directional characteristics of an oblique wing mounted on top of a body of revolution were measured. The wing had an aspect ratio of 6 (based on the unswept wing span) and was tested at various sweep angles ranging from 0 deg to 60 deg. Krueger nose flaps mounted on drooped-nose flaps were investigated on the downstream wing panel (for sweep angles of 45 deg and 60 deg) in an attempt to create more symmetrical spanwise wing stalling at high lift coefficients. The tests were conducted over a Mach number range of 0.25 to 1.4 and an angle-of-attack range from -3 deg to 28 deg. With the oblique wing in the swept position, considerable difference in the aileron effectiveness was measured for positive or negative differential aileron deflections. With the wing swept 45 deg at a Mach number of 0.8 and above, an extension of the span of the Krueger nose flaps on the downstream wing panel did not improve the linearity of the pitching-, rolling-, and yawing-moment curves.

Hopkins, E. J.↗
NASA NTRS1977

A low speed two-dimensional study of flow separation on the GA(W)-1 airfoil with 30-percent chord Fowler flap

Measurements of flow fields with low speed turbulent boundary layers were made for the GA(W)-1 airfoil with a 0.30 c Fowler flap deflected 40 deg at angles of attack of 2.7 deg, 7.7 deg, and 12.8 deg, at a Reynolds number of 2.2 million, and a Mach number of 0.13. Details of velocity and pressure fields associated with the airfoil flap combination are presented for cases of narrow, optimum and wide slot gaps. Extensive flow field turbulence surveys were also conducted employing hot-film anemometry. For the optimum gap setting, the boundaries of the regions of flow reversal within the wake were determined by this technique for two angles of attack. Local skin friction distributions for the basic airfoil and the airfoil with flap (optimum gap) were obtained using the razor blade technique.

Seetharam, H. C.↗
NASA NTRS1977

Flap noise and aerodynamic results for model QCSEE over-the-wing configurations

Noise spectra in three dimensions and aerodynamic data were measured for a model of the NASA QCSEE (Quiet Clean Short-Haul Experimental Engine) over-the-wing configuration. The effects of flap length, nozzle exhaust velocity, and nozzle geometry were determined using a single nozzle and wing-flap segment. Related tests indicated that the scaled-up model data would be representative of full scale flap noise with the QCSEE engine. The scaled-up QCSEE model data imply that the noise goal will be very nearly attained.

Olsen, W.↗
NASA NTRS1976

Flap-augmented shrouds for aerogenerators

Axisymmetrical shrouds for windmills are augmented by ring-shaped 'flaps' and their performance is studied experimentally. The concept of the shroud as an annular 'wing' is justified, leading to the conclusion that high-lift techniques should be used in shroud design, and that high-lift devices, such as flaps, would increase the power output of the windmill. It is shown experimentally that the ideal power output of a flap-augmented shrouded turbine can be more than 4 times the power of unshrouded turbines of the same diameter.

Seginer, A.↗
NASA NTRS1977

Use of simplified flow separation criteria for slotted flap preliminary design

From experimental correlations of airfoil and flap pressure distributions, it is observed that flow separation is likely to occur when the canonical pressure recovery coefficient (C sub pr) exceeds a critical value. A procedure is described for obtaining the C sub pr parameter from modified inviscid analysis. The procedure has been applied to preliminary design studies of a new slotted flap to determine the influence of shape and location. Experiments are planned to evaluate the flap designed by this procedure.

Wentz, W. H., Jr.↗
NASA NTRS1977

Acoustic source location in the secondary mixing region of a jet-blown flap using a cross-correlation technique

An experimental investigation of the acoustic sources in the secondary mixing region of a laboratory-scale jet-flap was made using a causality correlation technique. The processed signal of a hot-film anemometer probe was cross correlated with the output signal of a far-field microphone. Axial acoustic source strength distributions were measured for three far-field microphone locations: plus or minus 45 deg in the flyover plane and 45 deg in the sideline plane. These measurements showed that the acoustic sources in the secondary mixing region are highly directional, radiating much more effectively to the -45 deg-microphone, located below the plane of the flap surface. A relative maximum in the acoustic source strength measured for the microphones in the flyover plane occurred very near the flap trailing edge, which may be due to an edge amplification effect predicted by the theoretical work of Ffowcs Williams and Hall.

Becker, R. S.↗
NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗
NASA NTRS1977

Aircraft wake-vortex minimization by use of flaps

A survey was made of research on the alleviation of the trailing vortex hazard by altering span loading with flaps on the generator airplane. Flap configurations of the generator that shed multiple vortices were found to have wakes that dispersed by vortex merging and sinusoidal instability. Reductions of approximately 50 percent in both the wake rolling moment imposed on a following aircraft and the aircraft separation requirement were achieved in the ground based and flight test experiments by deflecting the trailing edge flaps more inboard than outboard. Significantly, this configuration did not increase the drag or vibration on the generating aircraft compared to the conventional landing configuration. Ground based results of rolling moment measurement and flow visualization are shown, using a water tow facility, an air tow facility, and a wind tunnel. Flight test results are also shown, using a full scale B-747 airplane. General agreement was found among the results of the various ground based facilities and the flight tests.

Corsiglia, V. R.↗
NASA NTRS1977

Finite element analysis of aeroacoustic jet-flap flows

A computational analysis was performed on the steady, turbulent aerodynamic flowfields associated with a jet-blown flap. For regions devoid of flow separation, a parabolic approximation to the governing time-averaged Navier-Stokes equations was applied. Numerical results are presented for the symmetry plane flow of a slot-nozzle planar jet flap geometry, including prediction of flowfield evolution within the secondary mixing region immediately downstream of the trailing edge. Using a two equation turbulence kinetic energy closure model, rapid generation and decay of large spatial gradients in mean and correlated fluctuating velocity components within the immediate wake region were predicted. Modifications to the turbulent flow structure, as induced by porous surface treatment of the flap, were evaluated. The recirculating flow within a representative discrete slot in the surface was evaluated, using the two dimensional, time-averaged Navier-Stokes equations.

Baker, A. J.↗
NASA NTRS1976

USB noise reduction by nozzle and flap modifications

The development of concepts for reducing upper surface blown flap noise at the source through flap modifications and special nozzles is reviewed. In particular, recent results obtained on the aerodynamic and acoustic performance of flaps with porous surfaces near the trailing edge and multi-slotted nozzles are reviewed. Considerable reduction (6-10 db) of the characteristic low frequency peak is shown. The aerodynamic performance is compared with conventional systems, and prospects for future improvements are discussed.

Hayden, R. E.↗
NASA NTRS1979

Leading edge vortex-flap experiments on a 74 deg delta wing

Exploratory wind tunnel tests are reported on a 74 deg. delta wing model. The potential of a vortex flap concept in reducing the subsonic lift dependent drag of highly swept, slender wings is examined. The suction effect of coiled vortices generated through controlled separation over leading edge flap surfaces to produce a thrust component is discussed. A series of vortex-flap configurations were investigated to explore the effect of some primary geometric variables.

Rao, D. M.↗