Search NASA⌕ Search

SEARCH · Search NASA

Results for “interdiffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

High Tc screen-printed YBa2Cu3O(7-x) films - Effect of the substrate material

Thick films of YBa2Cu3O(7-x) have been deposited on highly polished alumina, magnesia spinel, nickel aluminum titanate (Ni-Al-Ti), and barium tetratitanate (Ba-Ti) substrates by the screen printing technique. Properties of the films were found to be highly sensitive to the choice of the substrate material. The film on Ba-Ti turned green after firing, due to a reaction with the substrate and were insulating. A film on Ni-Al-Ti had a Tc (onset) of about 95 K and lost 90 percent of its resistance by about 75 K. However, even at 4 K it was not fully superconducting, possibly due to a reaction between the film and the substrate and interdiffusion of the reaction products. The film on alumina had Tc (onset) of about 96 K, Tc (zero) of about 66 K, and Delta Tc of about 10 K. The best film was obtained on spinel and had Tc (onset) of about 94 K, zero resistance at 81 K, and a transition width of about 7 K.

Bansal, Narottam P.↗

Microstructural aspects of zirconia thermal barrier coatings

Various combination of plasma-sprayed bond coatings and zirconia ceramic coatings on a nickel-based superalloy substrate were tested by static thermal exposure at 1200 C and cyclic thermal exposure to 1000 C. The bond coats were based on Ni-Cr-Al alloys with additions of rare earth elements and Si. The ceramic coats were various ZrO2-Y2O3 compositions, of which the optimum was found to be ZrO2-8.9 wt percent Y2O3. Microstructural analysis showed that resistance to cracking during thermal exposure is strongly related to deleterious phase changes. Zones depleted of Al formed at the bond coat/ceramic coat interface due to oxidation and at the bond coat/substrate interface due to interdiffusion, leading eventually to breakdown of the bond coat. The 8.9 percent Y2O3 coating performed best because the as-sprayed metastable tetragonal phase converted slowly into the low-Y2O3 tetragonal plus high-Y2O3 cubic-phase mixture, so that the deleterious monoclinic phase was inhibited from forming. Failure appeared to start with the formation of circumferential cracks in the zirconia, probably due to compressive stresses during cooling, followed by the formation of radial cracks due to tensile stresses during heating. Cracks appeared to initiate at the Al2O3 scale/bond coat interface and propagate through the zirconia coating. Comparisons were made with the behavior of bulk ZrO2-Y2O3 and the relationship between the microstructure of the tetragonal phase and the phase diagram. A separate investigation was also made of the ZrO2-Al2O3 interface.

Mitchell, T. E.↗

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗

Interdiffusional effects between TiBe12 and NiAl intermetallics

The TiBe12/NiAl composites fabricated by a powder metallurgy technique were examined for the extent of interdiffusion between its components, using scanning Auger microscopy. The results revealed an evidence of a reaction between the two component intermetallics after annealing at 1300 K for 100 h, with a 95-micron reaction zone extending from the TiBe12/NiAl interface. The concentration profile across the reaction zone showed that the Ni, Al, and Be concentrations were in a 1:1:2 ratio, while Ti was present in only very small amounts.

Carbone, A. J.↗

Measurement of the diffusion coefficient of acetone in succinonitrile at its melting point

The diffusion coefficient of acetone in liquid succinonitrile at 331.1 K was determined using the method of McBain and Dawson (1935). Only dilute mixtures of SCN-acetone were studied. The interdiffusion constant was determined to be 0.0000127 sq cm/s and was essentially independent of the acetone concentration over the range investigated (0.5 to 18 mol pct acetone).

Chopra, M. A.↗

Chemical profiling of silicon nitride structures

X ray photoelectron spectroscopy (XPS), spectroscopic ellipsometry (SE), and scanning electron microscopy (SEM) were used to study structural and chemical inhomogeneities in several electronic materials and device structures of relevance to radiation hard electronics. The systems studied include metal nitride oxide semiconductor (MNOS) structures, silicon oxynitride (SiO(x)N(y)) formed by the thermal nitridation of SiO2, and semiconductor on insulator (SOI) structures. Studies of MNOS structures suggest that the effect of H2 annealing is to make the Si3N4/SiO2 interface less abrupt by causing interdiffusion of silanol and silamine groups with subsequent oxynitride formation. Another effect of the annealing appears to be to relieve the strain at the SiO2/Si interface.

Vasquez, R. P.↗

Tracer versus trace element diffusion - Diffusional decoupling of Sr concentration from Sr isotope composition

Chemical diffusivities for nonalkali major, minor, and selected trace elements have been measured at 10 kbar, 1300 C during interdiffusion of dacitic and rhyolitic melts. Sr tracer diffusivities were measured at the same conditions in melts of dacitic and rhyolitic composition and in a diffusion couple of these two melts undergoing simultaneous chemical diffusion. Chemical diffusivities of all elements studied are functions of the silica content of the melt, but at any one silica content the chemical diffusivities of all elements studied are within a factor of five of the Si and Al diffusivities. Si diffusivity varies from 2.8 x 10 to the -9th sq cm/s at 65 percent SiO2 to 5.1 x 10 to the -10th sq cm/s at 75 percent SiO2. The diffusivities of minor and trace elements are proposed to be controlled by the ability of the local melt structure to accommodate these elements while maintaining LTE. The measured Sr tracer diffusivities are an order of magnitude above Sr chemical diffusivities.

Baker, Don R.↗

Ballistic electron emission microscopy and spectroscopy of Au/GaAs interfaces

This paper presents the first Schottky barrier results for the Au/GaAs(100) interface prepared completely in situ on GaAs grown by molecular-beam epitaxy. The resulting interface displays unexpected properties which can be interpreted in terms of enhanced electrode interdiffusion. In addition, the capability of molecular-beam epitaxy for in situ processing enables the stabilization of this interface against diffusion and allows the formation of a Au/GaAs system with nearly ideal properties. Newly developed ballistic electron spectroscopy and imaging techniques demonstrate that the heterogeneity present at the interface of Au/GaAs(100) fabricated on chemically treated GaAs substrates is removed.

Kaiser, W. J.↗

Combustion interaction with radiation-cooled chambers

Over 15 hours of thruster operation at temperatures between 1916 and 2246 C without failure or erosion has been demonstrated using iridium-coated rhenium chamber materials with nitrogen tetroxide/monomethylhydrazine propellants operating over a mixture ratio range of 1.60-2.05. Research is now under way to provide a basic understanding of the mechanisms which make high-temperature operation possible and to extend the capability to a wider range of conditions, including other propellant combinations and chamber materials. Techniques have been demonstrated for studying surface fracture phenomena. These include surface Raman and Auger for study of oxide formation, surface Raman and X-ray diffraction to determine the oxide phase, Auger to study oxide stoichiometry, and sputter Auger to study interdiffusion of alloy species.

Rosenberg, S. D.↗

Reaction of beta-phase Ni-Al alloys with CrB2

Reaction of Ni-Al alloys within the beta-NiAl phase with CrB2 was studied at 1473 K as a function of Al concentration in the alloy. Reaction of 49-50 at. pct Al alloys with CrB2 occurred by interdiffusion of Ni into CrB2 and Cr into the alloy without forming a new product phase. On the other hand, a new product phase, rich in Ni and B, formed by the reaction of alloys having Al concentrations 48 at. pct or lower with CrB2. The reaction product was observed both at the CrB2/alloy interface and along the alloy grain boundaries.

Misra, Ajay K.↗

High-T sub c fluorine-doped YBa2Cu3O(y) films on ceramic substrates by screen printing

Thick films of fluorine-doped YBa2Cu3O(y) were screen printed on highly polished alumina, magnesia spinel, strontium titanate, and yttria-stabilized zirconia (YSZ) substrates. They were annealed at 1000 C and soaked in oxygen at 450 C, followed by slow cooling to room temperature. The films were characterized by electrical resistivity measurements as a function of temperature and x-ray diffraction. The film on YSZ showed the best characteristics with a T sub c (onset) of 91 K, T sub c (R equals 0) of 88.2 K, and a transition width, delta T sub c (10-90 percent), of approximately 1.7 K. The film adhesion, probably controlled by interdiffusion of cations between the film and the substrate, was good in all cases except on strontium titanate where the film completely detached from the substrate.

Bansal, Narottam P.↗

Thermal histories of CO3 chondrites - Application of olivine diffusion modelling to parent body metamorphism

The petrologic sequence observed in the CO3 chondrite group has been suggested to be the result of thermal metamorphism on a parent body. A model developed to examine the possibility that chondrule and matrix olivines equilibrated in situ, during parent body metamorphism is presented. The model considers Fe-Mg interdiffusion between chondrule and matrix olivines. Zoning profiles comparable to those observed in chondrule olivines from partially equilibrated members of the series are reproduced successfully. Metamorphism of CO3 chondrites on a parent body is therefore a viable model for the observed equilibration. Results indicate that peak metamorphic temperatures experienced by the CO3 chondrites were around 500 C, and that the range of peak temperatures between unequilibrated and equilibrated subtypes was relatively narrow, around 100 C.

Jones, Rhian H.↗

Natural convection in binary gases driven by combined horizontal thermal and vertical solutal gradients

An investigation of natural convection is presented to examine the influence of a horizontal temperature gradient and a concentration gradient occurring from the bottom to the cold wall in a cavity. As the solutal buoyancy force changes from augmenting to opposing the thermal buoyancy force, the fluid motion switches from unicellular to multicellular flow (fluid motion is up the cold wall and down the hot wall for the bottom counterrotating flow cell). Qualitatively, the agreement between predicted streamlines and smoke flow patterns is generally good. In contrast, agreement between measured and predicted temperature and concentration distributions ranges from fair to poor. Part of the discrepancy can be attributed to experimental error. However, there remains considerable discrepancy between data and predictions due to the idealizations of the mathematical model, which examines only first-order physical effects. An unsteady flow, variable thermophysical properties, conjugate effects, species interdiffusion, and radiation were not accounted for in the model.

Weaver, J. A.↗

Low thrust chemical rocket technology

An on-going technology program to improve the performance of low thrust chemical rockets for spacecraft on-board propulsion applications is reviewed. Improved performance and lifetime is sought by the development of new predictive tools to understand the combustion and flow physics, introduction of high temperature materials and improved component designs to optimize performance, and use of higher performance propellants. Improved predictive technology is sought through the comparison of both local and global predictions with experimental data. Predictions are based on both the RPLUS Navier-Stokes code with finite rate kinetics and the JANNAF methodology. Data were obtained with laser-based diagnostics along with global performance measurements. Results indicate that the modeling of the injector and the combustion process needs improvement in these codes and flow visualization with a technique such as 2-D laser induced fluorescence (LIF) would aid in resolving issues of flow symmetry and shear layer combustion processes. High temperature material fabrication processes are under development and small rockets are being designed, fabricated, and tested using these new materials. Rhenium coated with iridium for oxidation protection was produced by the Chemical Vapor Deposition (CVD) process and enabled an 800 K increase in rocket operating temperature. Performance gains with this material in rockets using Earth storable propellants (nitrogen tetroxide and monomethylhydrazine or hydrazine) were obtained through component redesign to eliminate fuel film cooling and its associated combustion inefficiency while managing head end thermal soakback. Material interdiffusion and oxidation characteristics indicated that the requisite lifetimes of tens of hours were available for thruster applications. Rockets were designed, fabricated, and tested with thrusts of 22, 62, 440 and 550 N. Performance improvements of 10 to 20 seconds specific impulse were demonstrated. Higher performance propellants were evaluated: Space storable propellants, including liquid oxygen (LOX) as the oxidizer with nitrogen hydrides or hydrocarbon as fuels. Specifically, a LOX/hydrazine engine was designed, fabricated, and shown to have a 95 pct theoretical c-star which translates into a projected vacuum specific impulse of 345 seconds at an area ratio of 204:1. Further performance improvment can be obtained by the use of LOX/hydrogen propellants, especially for manned spacecraft applications, and specific designs must be developed and advanced through flight qualification.

Schneider, Steven J.↗

Fabrication of photovoltaic laser energy converterby MBE

A laser-energy converter, fabricated by molecular beam epitaxy (MBE), was developed. This converter is a stack of vertical p-n junctions connected in series by low-resistivity, lattice matched CoSi2 layers to achieve a high conversion efficiency. Special high-temperature electron-beam (e-beam) sources were developed especially for the MBE growth of the junctions and CoSi2 layers. Making use of the small (greater than 1.2 percent) lattice mismatch between CoSi2 and Si layers, high-quality and pinhole-free epilayers were achieved, providing a capability of fabricating all the junctions and connecting layers as a single growth process with one pumpdown. Well-defined multiple p-n junctions connected by CoSi2 layers were accomplished by employing a low growth temperature (greater than 700 C) and a low growth rate (less than 0.5 microns/hour). Producing negligible interdiffusion, the low growth temperature and rate also produced negligible pinholes in the CoSi2 layers. For the first time, a stack of three p-n junctions connected by two 10(exp -5) Ohm-cm CoSi2 layers was achieved, meeting the high conversion efficiency requirement. This process can now be optimized for high growth rate to form a practical converter with 10 p-n junctions in the stack.

Lu, Hamilton↗

Kinetics of diffusional droplet growth in a liquid/liquid two-phase system

This report contains experimental results for the interdiffusion coefficient of the system, succinonitrile plus water, at a number of compositions and temperatures in the single phase region of the phase diagram. The concentration and temperature dependence of the measured diffusion coefficient has been analyzed in terms of Landau - Ginzburg theory, which assumes that the Gibb free energy is an analytic function of its variables, and can be expanded in a Taylor series about any point in the phase diagram. At most points in the single phase region this is adequate. Near the consolute point (critical point of solution), however, the free energy is non-analytic, and the Landau - Ginzburg theory fails. The solution to this problem dictates that the Landau - Ginzburg form of the free energy be replaced by Widom scaling functions with irrational values for the scaling exponents. As our measurements of the diffusion coefficient near the critical point reflect this non-analytic character, we are preparing for publication in a refereed journal a separate analysis of some of the data contained herein as well as some additional measurements we have just completed. When published, reprints of this article will be furnished to NASA.

Baird, James K.↗

Non-destructive, ultra-low resistance, thermally stable contacts for use on shallow junction InP solar cells

Contact formation to InP is plagued by violent metal-semiconductor intermixing that takes place during the contact sintering process. Because of this the InP solar cell cannot be sintered after contact deposition. This results in cell contact resistances that are orders of magnitude higher than those that could be achieved if sintering could be performed in a non-destructive manner. We report here on a truly unique contact system involving Au and Ge, which is easily fabricated, which exhibits extremely low values of contact resistivity, and in which there is virtually no metal-semiconductor interdiffusion, even after extended sintering. We present a description of this contact system and suggest possible mechanisms to explain the observed behavior.

Weizer, V. G.↗

The structural and electrical properties of low-resistance Ni contacts to InP

We have investigated the electrical and metallurgical behavior of the Ni-InP contact system. Specific contact resistivity (Rc) values in the low 10 exp -7 Omega-sq cm range are achieved with Ni-only contacts on n-InP by sintering at 400 C for several minutes. The postsinter contact metallization consists of three layers, arranged in the sequence: InP/Ni3P/Ni2P/In. Extended sintering (40 min) at 400 C brings about a rise in Rc to the 10 exp -4 Omega-sq cm range. After extended sintering, the contact metallization is found to consist of only two layers, arranged in the sequence: InP/Ni2P/In. Based on the correlation between low Rc and the presence of Ni3P at the metal-InP interface, it is suggested that the presence of Ni3P is the cause of the low Rc values. We show that the sintering schedule used to achieve low values of Rc is accompanied by substantial metal-InP interdiffusion that results in severe device degradation.

Fatemi, Navid S.↗