Search NASA⌕ Search

SEARCH · Search NASA

Results for “lapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Process Parameter Optimization in Refill Friction Spot Welding of 6061 Aluminum Alloys Using Response Surface Methodology

6061-T6 aluminum alloy joint was fabricated by refill friction stir spot welding (RFSSW) on which three process parameters of tool rotation speed, sleeve moving rate, and plunge depth make an important effect. The response surface methodology (RSM) was applied to establish a mathematical model to study the effect of process parameters on lap shear fracture load (LSFL) of the RFSSWed joints which were performed in Box–Behnken designs with three factors, three levels and 15 runs. Analysis of variance used to check the adequacy of the developed model indicates that the mathematical model is significant. LSFL increases with the increase in tool rotation speed, sleeve plunge depth, and sleeve moving rate to maximum and then decreases. Sleeve plunge depth makes the most effect on LSFL in all process parameters. The RFSSW process parameters were also optimized using RSM to predict maximize LSFL. The joint produced using a tool rotational speed of 1506 rpm, sleeve moving rate of 1.01 mm/s and sleeve plunge depth of 2.46 mm displays higher LSFL.

36 MATERIALS SCIENCE↗

Effect of Welding Parameters on the Corrosion Behavior of Dissimilar Alloy Welds of T6 AA6061 Al-Galvanized Mild Steel

Partial replacement of steel by Aluminium (Al) alloys is a promising approach adopted by automotive sector to improve fuel efficiency without compromising on the strength. However, this results in the generation of dissimilar welds of Al alloys and steel. Understanding the corrosion behavior of Al alloys–steel welds as a function of welding parameters is critical in the successful application of such alloys. The present study reports the intergranular corrosion behavior of T6 heat-treated AA6061 Al alloy-galvanized mild steel lap joints, welded by metal inert gas welding–brazing technique as a function of different welding parameters, viz. weld speed (4-6 m/min) and wire feed rate (0.8-0.9 m/min), following ASTM G 67-04. Weld characterization was performed by field emission scanning electron microscopy (FESEM), x-ray diffraction and nano-hardness measurement. Results indicate heavy dissolution and metal loss at the interface. A high volume fraction of Al-Fe intermetallics was precipitated at the weld interfaces, resulting in high hardness and higher localized corrosion. The thickness of Al-Fe intermetallic layer increased with increasing wire feed rate and lower weld speed which enhanced the severity of galvanic and intergranular corrosion.

36 MATERIALS SCIENCE↗

Improvement of Al/Steel Tungsten Inert Gas Welding–Brazing Joint by High-Energy Shot Peening

High-energy shot peening treatment was applied to improve the Al/steel tungsten inert gas welding–brazing lap joint. The mechanical properties and microstructure evolution of the joint were investigated. Results showed that the mechanical properties of weld were evidently reinforced due to microstructure transformation of joint surface layer. The grain structure in the joint surface layer was distorted and refined. Large compressive residual stress was introduced into the joint surface, and its hardness obviously increased due to strain hardening. When the peening pressure was 0.15 MPa, the tensile shear strength of the joint reached the maximum value (199.6 MPa), which was 16.5% higher than that of the as-welded joint.

36 MATERIALS SCIENCE↗

Hybrid fiber metal composite laminate interlaminar reinforcement through metal interlocks

Aircraft and automobile industries are continually seeking high-performance and lightweight solutions. Fiber-reinforced composites in conjunction with metals are being considered in the form of hybrid materials. There is a continuous need for improvement of interfacial bonding between composite layers and metal constituents. In this study, an innovative hybrid fiber interlocking metal hooks laminate (FIMHL) system was developed in which fiber-reinforced thermoset composite, and metal sheets are mechanically bonded together using out of plane hooks stamped in the metal. Process optimization was performed to gain the full benefit of the through-thickness reinforcement. Microstructural analysis showed improved interaction between the metal hooks and the fiber layers which reduced porosity and resin richness. This was reflected in mechanical properties, as tensile and flexural strength of FIMHL was enhanced by 38.5 and 18.8%, respectively, after process optimization. Furthermore, normalized weight fraction (76.4%) properties of FIMHL also confirmed that the increase in mechanical properties of optimized panel were not only due to increased reinforcement (glass fiber + aluminum) volume fraction but also because of improved metal hooks and fibers interaction. There was no significant effect on lap shear and fracture toughness, as they depend on bend back behavior of the hooks. A bilinear traction-separation model was used to characterize mode-I interlaminar fracture toughness properties, and 4.5% variation was recorded when modeling and experimental values were compared.

36 MATERIALS SCIENCE↗

Self-healing, re-adhering, and carbon-steel corrosion mitigating properties of fly ash-containing calcium aluminum phosphate cement composite at 300 °C hydrothermal temperature

This study assesses here the ability of calcium aluminate phosphate (CAP)/fly ash F (FAF) blend composite to self-heal at early age; to re-adhere to the casing surfaces after debonding and to protect carbon steel (CS) against brine-caused corrosion before and after the re-adherence. The composite was damaged after autoclaving for 24 h at 300 °C and then exposed to the same conditions for 5 more days for the self-healing and re-adhering processes. The ability of the blend to self-heal and re-adhere to CS was evaluated 1) by measurements of the recovery of compressive and bond strengths and Young's modulus; 2) by performing the 3-dimensional micro-image analysis of sealed cracks; 3) by phase identification in composite matrix and in the cracks after the healing; 4) by measurements of CS corrosion impediment by the re-adhered composite after 300°C-5-day restoration period. After the healing, the two factors, sealing effect of cracks by reaction products and change in phase composition of cement matrix, essentially governed the recovery of the original mechanical strength. For the former, analcime phase derived from pozzolanic FAF autogenous healing aid played the major role in sealing the cracks, while the well-formed hydroxyapatite phase contributed to the latter factor. The lap-shear bond with the strength of 1.11 MPa at CS plate/composite adhesive/CS plate joint failed cohesively, showing higher bond strength than strength of the composite matrix. The rebonded composite-CS plates developed a 0.37 MPa bond strength after the 5-day restoration period. The results of electrochemical polarization corrosion tests revealed that the re-adhered composite covering CS plate significantly inhibited the brine-caused corrosion of CS, leading to 0.011 mm/year corrosion rate, corresponding to 50% reduction compared with that of before re-adhering. There were two factors governing such corrosion mitigation: enhanced adhesive contact of composite with CS and increased coverage by the re-adhering composite.

36 MATERIALS SCIENCE↗

Current activated reactive ultrafast joining (CARUJ) of silicon carbide

In this work we propose and demonstrate a novel approach for rapid fabrication of ceramic-ceramic joint assemblies, using sintered Silicon Carbide (SiC) as an initial example. Current Activated Reactive Ultrafast Joining (CARUJ) utilizes resistive heating of carbon-based materials to apply localized heat at or around the joint zone at heating rates of 101– 103 °C/min. CARUJ is used to fabricate SiC-SiC joints with a Si-SiC interface using minimal pressure (1–2 MPa) at time scales considerably shorter (several minutes opposed to hours) than conventional approaches for similar systems. The reaction of an interfacial precursor based on elemental silicon and carbon leads to in-situ SiC formation to produce a continuous and dense bond in a single step. Measured average joint strengths of roughly 15 MPa are achieved when tested in single lap offset (SLO) compressive shear. Optional additions of refractory metals such as molybdenum can be utilized to introduce secondary inclusions such as MoSi 2 within the joint interface. We further demonstrate SiC-SiC joining using Active Brazing Alloys (ABA) and proof of concept joining of tubular geometries. The localized and rapid heat application realizes a versatile material joining technique that could be extended for joining components at the plant site.

36 MATERIALS SCIENCE↗

Characterization of microstructure and residual stress following the friction stir welding of dissimilar aluminum alloys

Friction-stir-welding (FSW) has gained importance as an effective way to join dissimilar materials due to its solid-state nature. However, FSW produces substantial residual stresses in aluminum welding, often deteriorating the component's structural performance and reliability. In the current study, the d-spacing (inter-atomic distance) of several locations on a battery tray and stress-free reference samples are measured with neutron diffraction to calculate the residual stresses in a lap 6061 to A365 dissimilar friction-stir-weld. Furthermore, the present study connects the measured residual stress to microstructure properties through electron backscatter diffraction (EBSD) and optical microscopy analyses. The EBSD results indicate that the FSW operation affects the grains’ orientation, thereby producing location-specific directionally varying elasticity across the weldment. Further, this varied elasticity creates unique d-spacing profiles even in the stress-free material. Additionally, the resulting stressed and stress-free d-spacing profiles show dependencies on the FSW tool geometry, traverse direction, and rotational direction. Lastly, this study suggests that the final component residual stress can be influenced by the sequence of multi-pass welds contributing to a rise in temperature in the presence of a completed weld relaxing its residual stress.

36 MATERIALS SCIENCE↗

From acetone fractionation to lignin-based phenolic and polyurethane resins

In this paper, acetone fractionation was used to increase the homogeneity of softwood kraft lignin for product development. The acetone soluble and insoluble fractions were analyzed in terms of elemental composition, chemical structure, and thermal properties. The phenolic hydroxyl content of the acetone soluble fraction increased by 24%. The acetone soluble fraction of kraft lignin was used to fully substitute phenol in phenolic resin formulation. The resulting formulated lignin-formaldehyde adhesive showed higher adhesion strength (4.3 MPa) compared to a lab formulated phenol-formaldehyde resin (3.4 MPa) with 100% wood failure after lap shear test. On the other hand, the acetone insoluble lignin fraction, which had 23% higher aliphatic hydroxyl content compared to the starting lignin, was used to entirely replace petroleum-based polyol in polyurethane resin formulation. Then a bio-derived solvent (dihydrolevoglucosenone, Cyrene) was used to dissolve the acetone insoluble lignin fraction to synthesize lignin-based polyurethane resin. Tailoring the structure of kraft lignin through solvent fractionation resulted in two fractions, which were used to replace 100% of two major petrochemicals (phenol and polyol) in the formulations of phenolic and PU resins, that would otherwise be challenging due to the heterogeneity of softwood kraft lignin.

36 MATERIALS SCIENCE↗

Mechanical joint performances of friction self-piercing riveted carbon fiber reinforced polymer and AZ31B Mg alloy

Carbon fiber reinforced polymer (CFRP) and AZ31B Mg alloy were joined by the friction self-piercing riveting (F-SPR) with different steel rivet shank sizes. With the increase of rivet shank size, lap shear fracture load and mechanical interlock distance increased. Ultrafine grains were formed at the joint in AZ31B as a result of dynamic recrystallization, which contributed to the higher hardness. Fatigue life of the CFRP-AZ31B joint was studied at various peak loads of 0.5, 1, 2, and 3 kN and compared with the resistance spot welded AZ31B-AZ31B from the open literature. The fatigue performance was better at higher peak load (>2 kN) and comparable to that of resistance spot welding of AZ31B to AZ31B at lower peak loads (<1 kN). From fractography, the crack initiation for lower peak load (<1 kN) case was observed at the fretting positions on the top and bottom surfaces of AZ31B sheet. When peak load was increased, fretting between the rivet and the top of AZ31B became more dominant to initiate a crack during fatigue testing.

36 MATERIALS SCIENCE↗

Galvanic corrosion of AZ31B joined to dual-phase steel with and without Zn layer by ultrasonic and friction stir welding

Galvanic corrosion of AZ31B joined with bare or Zn-coated DP590 steel by ultrasonic spot welding or linear friction stir welding was quantitatively studied by pre-defining anode and cathode in the lap joint samples. Corrosion volume and depth from Mg anode surfaces exposed to 0.1 M sodium chloride solution was analyzed as functions of cathode surface type and welding method. Characterization of as-welded joints was performed to identify any microstructural feature of the bonding zone that could impact galvanic corrosion behavior. COMSOL modeling with modified user subroutine was conducted to simulate the progression of Mg corrosion in the same joint and electrode configurations used for the corrosion experiments. The experimental results indicated that Zn-coated cathode surface can reduce Mg galvanic corrosion significantly as galvanic polarization and cathodic current on Zn-coated surface remained relatively low for Mg in the weld joints. COMSOL modeling described the growth of Mg galvanic corrosion in a reasonable manner but showed limitation by underestimating the corrosion volume as it did not capture self-corrosion.

36 MATERIALS SCIENCE↗

Joining sheet aluminum AA6061-T4 to cast magnesium AM60B by vaporizing foil actuator welding: Input energy, interface, and strength

Dissimilar joining of sheet aluminum AA6061-T4 to cast magnesium AM60B was achieved by vaporizing foil actuator welding (VFAW). Three input energy levels were used (6, 8, and 10 kJ), and as a trend, higher input energies resulted in progressively higher flyer velocities, more pronounced interfacial wavy features, larger weld zones, higher peel strengths, and higher peel energies. In all cases, weld cross section revealed a soundly bonded interface characterized by well-developed wavy features and lack of voids and continuous layers of intermetallic compounds (IMCs). At 10 kJ input energy, flyer speed of 820 m/s, peel strength of 22.4 N/mm, and peel energy of 5.2 J were obtained. In lap-shear, failure occurred in AA6061- T4 flyer at 97% of the base material’s peak tensile load. Peel samples failed along the weld interface, and the AM60B-side of the fracture surface showed thin, evenly-spaced lines of Al residuals which had been torn out of the base AA6061-T4 in a ductile fashion and transferred over to the AM60B side, indicating very strong AA6061-T4/AM60B bond in these areas. Furthermore, this work demonstrates VFAW’s capability in joining dissimilar lightweight metals such as Al/Mg, which is expected to be a great enabler in the ongoing push for vehicle weight reduction.

36 MATERIALS SCIENCE↗

Stress characterization for friction-stir-welded electric vehicle battery trays with application of neutron diffraction

The battery tray is an essential component that protects and controls battery-cell temperatures in electric and plug-in hybrid vehicles. The functional stress limit of the battery tray heavily depends on the residual stress acquired from the manufacturing process. Consequently, exceeding the stress limit of the battery tray during operation could compromise the battery-cell banks and may risk the vehicle's safety. Hence, understanding residual stress formation is vital for design and safety concerns. Here, in the current study, AA 6061-plates were friction stir welded to an A365 high-pressure die-cast battery tray to create sealed coolant channels in the battery tray. However, this multi-material lap friction stir weld introduces residual stress into the battery tray, resulting in distortion. This distortion was mitigated using burnishing or coining operations, though straightening the battery tray had initially unknown effects on the residual stress. Therefore, neutron diffraction was utilized to characterize residual stresses after straightening. The results indicate that the friction stir welding (FSW) operation generated residual stresses exceeding the yield strength of the material, consequently deforming the battery tray by ±3 mm from the pre-weld geometry. The burnishing operation reduced the residual stresses below the material's yield strength while restoring the tray to within ±0.75 mm of the pre-weld geometry. Similarly, the coining operation restored the battery tray to within ±0.75 mm of the pre-weld geometry, however, increasing the number of locations where the residual stress exceeds the yield strength of the material.

36 MATERIALS SCIENCE↗

Phosphate modulated luminescence in lanthanum vanadate nanorods- Catechin, polyphenolic ligand

Rare earth orthovanadates and phosphates offer a very high opportunity for fabrication of nanoscale devices that exploit their luminescence properties. Optimization of luminescence by way of modulation of size, shape, structure, and morphology has been an area of study for several researchers. There has been a debate as to whether doped orthophosphate or orthovanadate is better luminescent material as both are chemically similar. It has been reported earlier that catechin hydrate can play the role of a structure director and thus influence the luminescence properties of orthovanadates. In this work, a catechin modulated the synthesis of Eu-doped lanthanum orthophosphate by phosphate substitution into vanadate host lattice is reported. A mechanistic understanding of the luminescence changes in LaMO{sub 4} has been proposed. During the substitution of V with P, catechin modulates the structure between 1D nanorods and nanowires. The host crystal structure, shape, and size influence the luminescence properties in doped LaMO{sub 4}. - Graphical abstract: Schematic illustration for the formation process of LAP nanowires using catechin. Display Omitted - Highlights: • Lanthanum phosphate nanowires are prepared by catechin -natural product. • Morphology tuned from nanorods to nanowires with tune in host lattice. • Quenching of luminescence – Zeolite water and Eu{sup 3+} to Eu{sup 2+} reduction. • The crystal structures was investigated by XRD, NMR, XPS and EPR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Three-dimensional (3D) visualization of reflow porosity and modeling of deformation in Pb-free solder joints

The volume, size, and dispersion of porosity in solder joints are known to affect mechanical performance and reliability. Most of the techniques used to characterize the three-dimensional (3D) nature of these defects are destructive. With the enhancements in high resolution computed tomography (CT), the detection limits of intrinsic microstructures have been significantly improved. Furthermore, the 3D microstructure of the material can be used in finite element models to understand their effect on microscopic deformation. In this paper we describe a technique utilizing high resolution (< 1 {mu}m) X-ray tomography for the three-dimensional (3D) visualization of pores in Sn-3.9Ag-0.7Cu/Cu joints. The characteristics of reflow porosity, including volume fraction and distribution, were investigated for two reflow profiles. The size and distribution of porosity size were visualized in 3D for four different solder joints. In addition, the 3D virtual microstructure was incorporated into a finite element model to quantify the effect of voids on the lap shear behavior of a solder joint. The presence, size, and location of voids significantly increased the severity of strain localization at the solder/copper interface.

36 MATERIALS SCIENCE↗

Grain structure, texture and mechanical property evolution of automotive aluminium sheet during high power ultrasonic welding

High power ultrasonic spot welding (HPUSW) is a joining technique which is performed within less than a second and provides a more energy-efficient alternative to friction stir spot welding (FSSW), which is considered a longer cycle manufacturing process for joining automotive alloys. To date, only a few reports exist on the deformation mechanisms that take place during high power ultrasonic spot welding. In this work, dynamic recrystallization and grain growth were examined using electron backscatter diffraction (EBSD). HPUSW causes extensive deformation within the weld zone where the temperature increases to 440 °C. An ultra-fine grain structure was observed in a thin band of flat weld interface within a short welding time of 0.10 s. With increasing welding time the interface was displaced and ‘folds’ or ‘crests’ appeared together with shear bands. The weld interface progressively changed from flat to sinusoidal and eventually to a convoluted wave-like pattern when the tool fully penetrated the workpiece, having a wavelength of ~ 1 mm after 0.40 s. Finally, the microstructure and texture varied significantly depending on the location within the weld. Although the texture near the weld interface was relatively weak, a shift was observed with increasing welding time from an initially Cube-dominated texture to one where the typical β-fibre Brass component prevailed. - Highlights: •Lap shear strength of ~2.9 kN was achieved in 0.30 sec welding time. •Temperature approached 440 °C along the weld centreline for the highest welding time. •The texture near the teeth was dominated by Brass, P and S components at optimum condition. •The weld interface showed typical β-fibre deformation texture at optimum condition.

36 MATERIALS SCIENCE↗

Characterisation of weld zone reactions in dissimilar glass-to-aluminium pulsed picosecond laser welds

Precision welded joints, produced between fused silica glass and aluminium by a newly-developed picosecond-pulse laser technique, have been analysed for the first time using a full range of electron microscopy methods. The welds were produced as lap joints by focusing a 1.2 μm diameter laser beam through the transparent glass top sheet, slightly below the surface of the metal bottom sheet. Despite the extremely short interaction time, extensive reaction was observed in the weld zone, which involved the formation of nanocrystalline silicon and at least two transitional alumina phases, γ- and δ-Al{sub 2}O{sub 3}. The weld formation process was found to be complex and involved: the formation of a constrained plasma cavity at the joint interface, non-linear absorption in the glass, and the creation of multiple secondary keyholes in the metal substrate by beam scattering. The joint area was found to expand outside of the main interaction volume, as the energy absorbed into the low conductivity and higher melting point silica glass sheet melted the aluminium surface across a wider contact area. The reasons for the appearance of nanocrystalline Si and transitional alumina reaction products within the welds are discussed. - Highlights: •Pulsed laser welding of dissimilar materials causes extensive chemical reactivity. •Metastable Al{sub 2}O{sub 3} phases form due to laser-induced highly-transient thermal regime. •Fused silica is reduced by Al to form nanocrystalline Si. •Mechanism of joint formation is discussed.

36 MATERIALS SCIENCE↗

On visualizing material flow and precipitate evolution during probeless friction stir spot welding of an Al-Li alloy

Highlights: • Severe thermal cycle and deformation refined grains and intermetallic particles in SZ. • T{sub 1} phases fully dissolved in SZ followed by re-precipitation of GP zone and δ′ phases. • The predominant flow direction remained in spiral-like pattern during P-FSSW. • Local abrasion existed in the lap-weld interface due to flow difference, forming joining. - Abstract: The precipitate evolution and material flow visualization during probeless friction stir spot welding (P-FSSW) of an Al-Li alloy has been investigated experimentally and numerically in this work. Due to severe heat input during welding, the main strengthening phases of T{sub 1} fully dissolved in the stir zone followed by the re-precipitation of GP zone and δ′ phases, assisted with the refinement of the intermetallic particles and grains. The history of material flow was three-dimensionally visualized with a tracer, studied with X-ray tomography. The experiments and the simulation results provided a consistent interpretation of a circumferential material flow which moved inwards radially near the top surface. Upward flow in the bottom sheet improved with dwell time, causing the interface to bend. Local abrasion between the two sheets due to flow difference led to the disruption of oxide layer, and formed a connection at the interface.

36 MATERIALS SCIENCE↗