Search NASA⌕ Search

SEARCH · Search NASA

Results for “lithium diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The drift field model applied to the lithium-containing silicon solar cell

The drift field model used by Wolf to calculate the short-circuit current was extended to permit calculations of the open-circuit voltage and the maximum power under conditions of illumination of either tungsten (2800 C) source or AMO sunlight. Voltages were calculated using an expression for the drift field diode saturation current derived here. The model, applied to the oxygen rich (C-13 group) lithium solar cells, was used to calculate the pre-and post-electron bombardment trends for lithium gradients in the range of 10 to the 18th power to 10 to the 19th power Li/cm to the 4th power. Published experimental data characterizing these cells were used to tailor the model. The calculated trends are in reasonable agreement with the empirical data of Faith. Diffusion length degradation and carrier removal effects were sufficient to predict the cell performance up to 3 x 10 to the 14th power e/sq cm. Beyond this fluence it was necessary to include drift field removal effects.

Godlewski, M. P.↗
NASA NTRS1991

Simulation of whistler waves excited in the presence of a cold plasma cloud - Implications for the CRRES mission

A one-dimensional electromagnetic particle simulation model is constructed to study the excitation of whistler waves in the presence of a cold plasma cloud for conditions representative of those after the release of lithium in the inner plasma sheet during the Combined Release and Radiation Effect Satellite mission. The results indicate that a standing-wave pattern with discrete wave frequencies is formed within the cloud. The magnetic wave amplitude inside the cloud, which is limited by quasi-linear diffusion, is of the order of several nanoteslas. Assuming a magnetospheric loss cone of 5 deg, the observed pitch angle diffusion produced by the whistler waves is sufficient to put the electrons on strong diffusion.

Pritchett, P. L.↗
DOE OSTI2020

Measurement of Three Transport Coefficients and the Thermodynamic Factor in Block Copolymer Electrolytes with Different Morphologies

The design and engineering of composite materials is one strategy to satisfy the materials needs of systems with multiple orthogonal property requirements. In the case of rechargeable batteries with lithium metal anodes, the system requires a separator with fast lithium ion transport and good mechanical strength. In this work, we focus on the system polystyrene-block-poly(ethylene oxide) (SEO) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). Ion transport occurs in the salt-containing poly(ethylene oxide)-rich domains. Mechanical rigidity arises due to the glassy nature of polystyrene (PS). If we assume that the salt does not interact with the PS-rich domains, we can describe ion transport in the electrolyte by three transport parameters (ionic conductivity, κ, salt diffusion coefficient, D, and cation transference number, t + 0 ) and a thermodynamic factor, T f . By systematically varying the volume fraction of the conducting phase, Φ c between 0.29 and 1.0, and chain length, N between 80 and 8000, we elucidate the role of morphology on ion transport. We find that κ is the strongest function of morphology, varying by three full orders of magnitude, while D is a weaker function of morphology. To calculate t + 0 and T f , we measure the current fraction, ρ + , and the open circuit potential, U, of concentration cells. We find that ρ + and U follow universal trends as a function of salt concentration, regardless of chain length, morphology, or Φ c , allowing us to calculate t + 0 for any SEO/LiTFSI or PEO/LiTFSI mixture when κ and D are known. Finally, the framework developed in this paper enables predicting the performance of any block copolymer electrolyte in a rechargeable battery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Bi-Layer Dense/Porous Solid Electrolyte Interphase for Enhanced Lithium-Metal Stability

Due to its high theoretical capacity and low electrochemical potential, lithium metal is a highly investigated anode for next-generation high-energy batteries. However, the unstable chemical and topographical heterogeneous surface of lithium gives rise to safety and efficiency concerns that prevent it from being utilized in practical applications. Exposure to electrolyte leads to non-uniform, mixed organic-inorganic solid-electrolyte interphase (SEI) formation, starting a cascading to non-uniform flux distribution, consumption of active materials, and dendrite growth. The SEI is the key feature that will lead to harnessing the capabilities possible with lithium metal. In this work, the formation of a closed-host bi-layer solid electrolyte interphase (SEI) improves the stability of lithium anode. This is successfully realized by forming an interconnected porous LiF-rich artificial SEI in contact with Li metal, and a dense, stable in-situ formed upper layer SEI. The porous layer increases the number of Li/LiF interfaces, which reduces local volume fluctuations and improves Li+ diffusion along these interfaces. Additionally, the tortuous porous structure guides uniform Li+ flux distribution and mechanically suppresses dendrite propagation. The dense upper layer of the SEI accomplishes a closed-host design through reaction with LiNO3 additive and prevents continuous consumption of active materials seen without the additive included in the electrolyte. The duality of a dense top layer with porous bottom layer led to extended cycle life and improved rate performance, evidenced with symmetric cell testing, as well as full cell testing paired with sulfur and LiFePO4 (LFP) cathodes. This work is a good example of a rational design of the SEI, based on comprehensive consideration of various critical factors to improve Li-metal anode stability, and highlights a new pathway to improve cycling and rate performances of Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Single crystal cathodes enabling high-performance all-solid-state lithium-ion batteries

All-solid-state lithium-ion batteries (ASSLIBs) are receiving significant attention owing to their improved safety and energy density over liquid counterparts. However, single-crystal cathodes have never been investigated in ASSLIBs. In this work, single-crystal Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 (SC-NMC532) is used as the cathode material for ASSLIBs, which exhibits 6~14 times higher Li + diffusion coefficient than polycrystalline Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 (PC-NMC532). As a result, SC-NMC532 exhibits an initial specific capacity of 156.4 mAh.g -1 while PC-NMC532 shows an initial capacity of only 127.5 mAh.g -1 . After 150 cycles, SC-NMC532 retains the capacity of 94.5 mAh.g -1 . More impressively, under a high current density of 1.3 mA.cm -2 , SC-NMC532 exhibits a capacity of 82 mAh.g -1 , much higher than that of PC-NMC532 (2.1 mAh.g -1 ). This work demonstrates that single-crystal NMC cathodes could enable both high power density and high energy density of ASSLIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

NaSICON-type materials for lithium-ion battery applications: Progress and challenges

Lithium-ion batteries (LIBs) are widely used in electric vehicles, energy storage, smart grids, and portable devices due to their high average output voltage and energy density. NaSICON-type materials have been identified as potential candidates for electrode and solid electrolyte materials for LIBs due to their 3D framework, which contains Li + ions, excellent ionic conductivity, and thermal stability. NaSICON-type materials have a 3D framework and a fast Li + diffusion pathway, making them suitable for use in LIBs. However, their application as solid electrolytes is limited due to poorer ionic conductivity and interfacial stability compared to commercialized liquid electrolytes. Furthermore, their use as electrode materials is restricted by their low electronic conductivity. Here, this review provides an overview of NaSICON-type materials, including their common structure, Li + diffusion mechanism, and preparation strategies. The article also discusses the application and modification strategies of NaSICON-type materials for LIBs, classifying them as anode materials, cathode materials, and solid electrolyte materials. Additionally, the potential use of NaSICON-type materials as modification materials for cathode materials for LIBs is briefly mentioned. Building on previous work on NaSICON-type materials, we propose potential areas for further development and wider applications of these materials in LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Modeling Chemo-Mechanics with Electrolyte Infiltration to Quantify Degradation of Cathode Particles

One of the main goals in modeling lithium-ion batteries is to improve/predict longevity and resilience of new chemistries. To that end, this talk investigates the formation of stress-induced fracture within polycrystalline cathode particles and the impact on capacity loss. Physically based cathode aging dynamics is simulated in a 3D, continuum-level chemo-mechanical model. The model captures anisotropic Li diffusion within a single polycrystalline particle comprised of hundreds to thousands of randomly oriented grains. A recent addition to this model includes electrolyte infiltration, which occurs when the electrolyte seeps into surface cracks within the particle. The model predicts that particle fracture is primarily due to non-ideal grain interactions with slight dependence on high-rate charge demands. Essentially, when neighboring grains are misaligned, they expand a different rates relative to one another leading to high stresses and ultimately the formation of intraparticle cracks. The model predicts that small particles with large grains develop significantly less damage than larger particles with small grains. Finally, the model predicts most of the chemo-mechanical damage accumulates in the first charge after formation. This chemo-mechanical "damage saturation" effect indicates that initial particle fracture occurs within the first few cycles, while long-term cathode degradation is not solely chemo-mechanically induced. The principle contribution of this research is the use of an anisotropic chemo-mechanical model to test how particle geometry affect capacity fade, which predicts that particle size has a stronger effect on capacity fade than grain size and ultimately that small particles with large grains have the least capacity fade.

cathode↗
NASA NTRS1973

Theoretical analysis of oxygen diffusion at startup in an alkali metal heat pipe with gettered alloy walls

The diffusion of oxygen into, or out of, a gettered alloy exposed to oxygenated alkali liquid metal coolant, a situation arising in some high temperature heat transfer systems, was analyzed. The relation between the diffusion process and the thermochemistry of oxygen in the alloy and in the alkali metal was developed by making several simplifying assumptions. The treatment is therefore theoretical in nature. However, a practical example pertaining to the startup of a heat pipe with walls of T-111, a tantalum alloy, and lithium working fluid illustrates the use of the figures contained in the analysis.

Tower, L. K.↗
DOE OSTI2025

Tetrahedral Lithium Stuffing in Disordered Rocksalt Cathodes for High-Power-Density and Energy-Density Batteries

Li-rich cation-disordered rocksalt (DRX) materials introduce new paradigms in the design of high-capacity Li-ion battery cathode materials. However, DRX materials show strikingly sluggish kinetics due to random Li percolation with poor rate performance. Here, in this study, we demonstrate that Li stuffing into the tetrahedral sites of the Mn-based rocksalt skeleton injects a novel tetrahedron-octahedron-tetrahedron diffusion path, which acts as a low-energy-barrier hub to facilitate high-speed Li transport. Moreover, the enhanced stability of lattice oxygen and the suppression of transition metal migration preserve the efficacy of the Li percolation network during cycling. Overall, the tetrahedral Li stuffing DRX material exhibits high energy density (311 mAh g -1 , 923 Wh kg -1 ) and high power density (251 mAh g -1 , 697 Wh kg -1 at 1000 mA g -1 ). Our results highlight the potential to develop high-performance and earth-abundant cathode materials within the extensive range of rocksalt compounds.

Disordered Rocksalt Cathodes↗
DOE OSTI2022

Quantifying Lithium Ion Exchange in Solid Electrolyte Interphase (SEI) on Graphite Anode Surfaces

Solid Electrolyte Interphase (SEI) has been identified as the most important and least understood component in lithium-ion batteries. Despite extensive studies in the past two decades, a few mysteries remain: what is the chemical form of and degree of mobility of Li + in the interphase? What fraction of Li + is permanently immobilized in the SEI, while the rest are still able to participate in the cell reactions via the ion-exchange process with Li + in the electrolyte? This study attempted to answer, in part, these questions by using 6 Li and 7 Li-isotopes to label SEIs and electrolytes, and then quantifying the distribution of permanently immobilized and ion-exchangeable Li + with solid-state NMR and ToF-SIMS. The results showed that the majority of Li + were exchanged after one SEI formation cycle, and a complete exchange after 25 cycles. Ion exchange by diffusion based on concentration gradient in the absence of applied potential also occurred simultaneously. This knowledge will provide a foundation for not only understanding but also designing better SEIs for future battery chemistries.

25 ENERGY STORAGE↗
DOE OSTI2023

Moisture Absorbing and Water Self‐Releasing from Hybrid Hydrogel Desiccants

Abstract Atmospheric moisture is a valuable resource for fresh water and potentially sustainable energy. However, direct harvesting water from moisture (the vapor form) remains the most challenging. Hybrid desiccants made from hydrogels embedded with salt offer promise in absorbing moisture. However, the desorption process often requires additional energy to heat the samples. Here, poly(acrylic acid) (PAA) hydrogels embedded with lithium chloride are prepared, demonstratng simultaneous moisture absorption and self‐release of liquid water at room temperature with 50–90% relative humidity. The water self‐releasing process can be separated into two distinct stages: 1) surface release, where water droplets grow on the hydrogel surface due to differences in nucleation and diffusion rates, and 2) bulk release, triggered by the collapse of polymer chains, subsequently releasing water from the hydrogel network. Factors such as salt concentration, hydrogel crosslinking density, and film thickness are investigated to better understand the moisture absorption and water‐releasing processes. Moreover, hydrophobic domains are introduced onto the salt‐embedded PAA films, creating an edge effect that enhances the droplet growth rates. When the hydrophobic domains are patterned, the movement of released water can be guided, resulting in a threefold increase in water removal rate attributed to gravitational force.

Chemistry↗
DOE OSTI2023

Complex defect chemistry of hydrothermally-synthesized Nb-substituted β$'$-LiVOPO 4

Lithium vanadyl phosphate (LiVOPO 4 ) is a next-generation multielectron battery cathode that can intercalate up to two Li-ions per V-ion through the redox couples of V 4+ /V 3+ and V 5+ /V 4+ . However, its rate capacity is undermined by the sluggish Li-ion diffusion in the high-voltage region (4 V for V 5+ /V 4+ redox). Nb substitution was used to expand the crystal lattice to facilitate Li-ion diffusion. Here, in this work, Nb substitution was achieved via hydrothermal synthesis, which resulted in a new, lower symmetry β'-LiVOPO 4 phase with preferential Nb occupation of one of the two V sites. This phase presents complex defect chemistries, including cation vacancies and hydrogen interstitials, characterized by a combination of X-ray and neutron diffraction, elemental and thermogravimetric analyses, X-ray absorption spectroscopy, and magnetic susceptibility measurements. The Nb-substituted samples demonstrated improved capacity retention and rate capabilities in the high-voltage region, albeit an enlarged voltage hysteresis related to a partial V 4+ /V 3+ redox reaction, as evidenced by ex situ X-ray absorption spectroscopy and pair distribution function analysis. This work highlights the importance of understanding the complex defect chemistry and its consequence on electrochemistry in polyanionic intercalation compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

An infrared, Raman, and X-ray database of battery interphase components

Further improvements to lithium-ion and emerging battery technologies can be enabled by an improved understanding of the chemistry and working mechanisms of interphases that form at electrochemically active battery interfaces. However, it is difficult to collect and interpret spectra of interphases for several reasons, including the presence of a variety of compounds. To address this challenge, we herein present a vibrational spectroscopy and X-ray diffraction data library of ten compounds that have been identified as interphase constituents in lithium-ion or emerging battery chemistries. The data library includes attenuated total reflectance Fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray diffraction data, collected in inert atmospheres provided by custom sample chambers. The data library presented in this work (and online repository) simplifies access to reference data that is otherwise either diffusely spread throughout the literature or non-existent, and provides energy storage researchers streamlined access to vital interphase-relevant data that can accelerate battery research efforts.

25 ENERGY STORAGE↗
NASA NTRS2005

Nanostructured MnO2-Based Cathodes for Li-Ion/Polymer Cells

Nanostructured MnO2-based cathodes for Li-ion/polymer electrochemical cells have been investigated in a continuing effort to develop safe, high-energy-density, reliable, low-toxicity, rechargeable batteries for a variety of applications in NASA programs and in mass-produced commercial electronic equipment. Whereas the energy densities of state-of-the-art lithium-ion/polymer batteries range from 150 to 175 W h/kg, the goal of this effort is to increase the typical energy density to about 250 W h/kg. It is also expected that an incidental benefit of this effort will be increases in power densities because the distances over which Li ions must diffuse through nanostructured cathode materials are smaller than those through solid bulk cathode materials.

Skandan, Ganesh↗
DOE OSTI2022

Unlocking Failure Mechanisms and Improvement of Practical Li-S Pouch Cells Through in Operando Pressure Study

For Lithium-sulfur (Li-S) battery commercialization, the study at a pouch cell level is essential, as some problems ignored or deemed minimal at the smaller level could have a greater effect on the performance of the larger pouch cell. Herein, the failure mechanisms of Li-S pouch cells are deeply investigated via in operando pressure analysis. It is found that highly porous structures of cathodes/separators and slow electrolyte diffusion through cathodes/separators can both lead to poor initial wetting. Additionally, Li-metal anode dominates the thickness variation of the whole pouch cell, which is verified by in situ measured pressure variation. Consequently, a real-time approach that combined normalized pressure with dP/dV analysis is proposed and validated to diagnose the morphology evolution of Li-metal anode. Moreover, applied pressure and porosity/tortuosity ratio of the cathode are both identified as independent factors that influence anode performance. In addition to stabilizing anodes, high pressure is proven to improve the cathode connectivity and avoid cathode cracking over cycling, which improves the possibility of developing cathodes with high sulfur mass loading. This work provides insights into Li-S pouch cell design (e.g., cathode and separator) and highlights pathways to improve cell capacity and cycling performance with applied and monitored pressure

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of Fluorination on Lithium Transport and Short-Range Order in Disordered-Rocksalt-Type Lithium-Ion Battery Cathodes

Fluorine substitution is a critical enabler for improving the cycle life and energy density of disordered rocksalt (DRX) Li-ion battery cathode materials which offer prospects for high energy density cathodes, without the reliance on limited mineral resources. Due to the strong Li–F interaction, fluorine also is expected to modify the short-range cation order in these materials which is critical for Li-ion transport. In this work, density functional theory and Monte Carlo simulations are combined to investigate the impact of Li–F short-range ordering on the formation of Li percolation and diffusion in DRX materials. Additionally, the modeling reveals that F substitution is always beneficial at sufficiently high concentrations and can, surprisingly, even facilitate percolation in compounds without Li excess, giving them the ability to incorporate more transition metal redox capacity and thereby higher energy density. It is found that for F levels below 15%, its effect can be beneficial or disadvantageous depending on the intrinsic short-range order in the unfluorinated oxide, while for high fluorination levels the effects are always beneficial. Using extensive simulations, a map is also presented showing the trade-off between transition-metal capacity, Li-transport, and synthetic accessibility, and two of the more extreme predictions are experimentally confirmed.

25 ENERGY STORAGE↗
DOE OSTI2023

Ion irradiation study of lithium silicates for fusion blanket applications

Here, this study reports on the microstructural and compositional evolutions, deuterium release and lithium loss behavior in lithium silicates. Pellets of biphasic Li 4 SiO 4 and Li 2 SiO 3 were fabricated using hot pressing of powders. Sequential irradiation with Si + , He + and D + ions was performed up to 773 K to emulate one-year 6 Li burnup in 6 Li 4 SiO 4 inside the SlimCS DEMO. Crystalline Li 4 SiO 4 phase was not observed in the irradiated depth region of all the samples in this study. In spite of full amorphization in the near-surface region, Li 2 SiO 3 irradiated to a high dose at 773 K remained crystalline in the damage peak region, suggesting that Li 2 SiO 3 is more irradiation resistant to amorphization than Li 4 SiO 4 . Radiolysis may be primarily responsible for silicate decomposition and amorphization. Data from this study also show that D release from the pellet is very efficient during ion irradiation at 773 K, which is accompanied with a significant Li loss. Thermal annealing for 10 min at 773 K for the room-temperature irradiated pellet leads to a nearly complete D release without an observable Li loss. A concept of Ni coating on tritium breeder materials is discussed with supporting data to minimize Li loss without a significant impact on tritium diffusion and release.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Solution-Based, Anion-Doping of Li 4 Ti 5 O 12 Nanoflowers for Lithium-Ion Battery Applications

Solution–based, anionic doping represents a convenient strategy with which to improve upon the conductivity of candidate anode materials such as Li 4 Ti 5 O 12 (LTO). As such, novel synthetic hydrothermally–inspired protocols have primarily been devised herein, aimed at the large–scale production of unique halogen–doped, micron–scale, three–dimensional, hierarchical LTO flower–like motifs. Although fluorine (F) doping has been explored, the use of chlorine (Cl) dopants is the primary focus here. Several experimental variables, such as dopant amount, lithium hydroxide concentration, and titanium butoxide purity, were probed and perfected. Furthermore, the Cl doping process did not damage the intrinsic LTO morphology. The analysis, based on interpreting a compilation of SEM, XRD, XPS, and TEM–EDS results, was used to determine an optimized dopant concentration of Cl. Electrochemical tests demonstrated an increased capacity via cycling of 12 % for a Cl–doped sample as compared with pristine LTO. Moreover, the Cl–doped LTO sample described in this study exhibited the highest discharge capacity yet reported at an observed rate of 2C for this material at 143mAh g –1 . Overall, these data suggest that the Cl dopant likely enhances not only the ion transport capabilities, but also the overall electrical conductivity of our as–prepared structures. Furthermore, to help explain these favorable findings, theoretical DFT calculations were used to postulate that the electronic conductivity and Li diffusion were likely improved by the presence of increased Ti 3+ ion concentration coupled with widening of the Li migration channel.

25 ENERGY STORAGE↗