SEARCH · Search NASA

Results for “numbers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Highlights of unsteady pressure tests on a 14 percent supercritical airfoil at high Reynolds number, transonic condition

Steady and unsteady pressures were measured on a 2-D supercritical airfoil in the Langley Research Center 0.3-m Transonic Cryogenic Tunnel at Reynolds numbers from 6 x 1,000,000 to 35 x 1,000,000. The airfoil was oscillated in pitch at amplitudes from plus or minus .25 degrees to plus or minus 1.0 degrees at frequencies from 5 Hz to 60 Hz. The special requirements of testing an unsteady pressure model in a pressurized cryogenic tunnel are discussed. Selected steady measured data are presented and are compared with GRUMFOIL calculations at Reynolds number of 6 x 1,000,000 and 30 x 1,000,000. Experimental unsteady results at Reynolds numbers of 6 x 1,000,000 and 30 x 1,000,000 are examined for Reynolds number effects. Measured unsteady results at two mean angles of attack at a Reynolds number of 30 x 1,000,000 are also examined.

Hess, Robert W.↗

NASA NTRS1986

Experimental evaluation of wall Mach number distributions of the octagonal test section proposed for NASA Lewis Research Center's altitude wind tunnel

Wall Mach number distributions were determined over a range of test-section free-stream Mach numbers from 0.2 to 0.92. The test section was slotted and had a nominal porosity of 11 percent. Reentry flaps located at the test-section exit were varied from 0 (fully closed) to 9 (fully open) degrees. Flow was bled through the test-section slots by means of a plenum evacuation system (PES) and varied from 0 to 3 percent of tunnel flow. Variations in reentry flap angle or PES flow rate had little or no effect on the Mach number distributions in the first 70 percent of the test section. However, in the aft region of the test section, flap angle and PES flow rate had a major impact on the Mach number distributions. Optimum PES flow rates were nominally 2 to 2.5 percent wtih the flaps fully closed and less than 1 percent when the flaps were fully open. The standard deviation of the test-section wall Mach numbers at the optimum PES flow rates was 0.003 or less.

Harrington, Douglas E.↗

NASA NTRS1987

Experimental study of low Reynolds number nozzles

High-performance electrothermal thrusters operate in a low nozzle-throat Reynolds number regime. Under these conditions, the flow boundary layer occupies a large volume inside the nozzle, contributing to large viscous losses. Four nozzles (conical, bell, trumpet, and modified trumpet) and a sharp-edged orifice were evaluated over a Reynolds number range of 500 to 9000 with unheated nitrogen and hydrogen. The nozzles showed significant decreases in specific impulse efficiency with decreasing Reynolds number. At Reynolds numbers less than 1000, all four nozzles were probably filled with a large boundary layer. The discharge coefficient decreased with Reynolds number in the same manner as the specific impulse efficiency. The bell and modified trumpet nozzles had discharge coefficients 4 to 8 percent higher than those of the cone or trumpet nozzles. The Two-Dimensional Kinetics (TDK) nozzle analysis computer program was used to predict nozzle performance. The results were then compared to the experimental results in order to determine the accuracy of the program within this flow regime.

Grisnik, Stanley P.↗

NASA NTRS1987

Effect of Reynolds number variation on aerodynamics of a hydrogen-fueled transport concept at Mach 6

Two separate tests have been made on the same blended wing-body hydrogen-fueled transport model at a Mach number of about 6 and a range of Reynolds number (based on theoretical body length) of 1.577 to 55.36 X 10 to the 6th power. The results of these tests, made in a conventional hypersonic blowdown tunnel and a hypersonic shock tunnel, are presented through a range of angle of attack from -1 to 8 deg, with an extended study at a constant angle of attack of 3 deg. The model boundary layer flow appeared to be predominately turbulent except for the low Reynolds number shock tunnel tests. Model wall temperatures varied considerably; the blowdown tunnel varied from about 255 F to 340 F, whereas the shock tunnel had a constant 70 F model wall temperature. The experimental normal-force coefficients were essentially independent of Reynolds number. A current theoretical computer program was used to study the effect of Reynolds number. Theoretical predictions of normal-force coefficients were good, particularly at anticipated cruise angles of attack, that is 2 to 5 deg. Axial-force coefficients were generally underestimated for the turbulent skin friction conditions, and pitching-moment coefficients could not be predicted reliably.

Penland, Jim A.↗

NASA NTRS1987

Highlights of unsteady pressure tests on a 14 percent supercritical airfoil at high Reynolds number, transonic condition

Steady and unsteady pressures were measured on a two-dimensional supercritical airfoil in the Langley 0.3-m Transonic Cryogenic Tunnel at Reynolds numbers (6-35) x 10 to the 6th. The airfoil was oscillated in pitch at amplitudes from + or - .25 degrees to + or - 1.0 degrees at frequencies from 5 Hz to 60 Hz. The special requirements of testing an unsteady pressure model in a pressurized cryogenic tunnel are discussed. Selected steady measured data are presented and are compared with GRUMFOIL calculations at Reynolds number 6 x 10 to the 6th and 30 x 10 to the 6th. Experimental unsteady results at the same Reynolds numbers are examined for Reynolds-number effects. Measured unsteady results at two mean angles of attack at Reynolds number of 30 x 10 to the 6th are also examined.

Hess, Robert W.↗

NASA NTRS1987

An unconditionally-stable central differencing scheme for high Reynolds number flows

The central difference scheme (CDS) is a second order accurate scheme which is free of numerical diffusion (in the second order sense) and is simple to implement: However, for grid Peclet numbers larger than 2, the CDS leads to over- and undershoots and is unstable. The present paper describes a method, called CONDIF, which retains the essential nature of the CDS but eliminates the over- and under-shoots. It leads to unconditionally positive coefficients and, in the limit, approaches the CDS for all values of grid Peclet numbers. The CONDIF modifies the CDS by introducing a controlled amount of numerical diffusion based on the local gradients. In the worst case the scheme yields results similar to those of the hybrid scheme. This paper reports the results obtained from CONDIF for a number of test problems which have been widely used for comparative study of numerical schemes in the published literature. For most of these problems, the CONDIF results are significantly more accurate than the hybrid scheme at high Peclet numbers. In particular, the CONDIF scheme depicts much lower level of numerical diffusion than the hybrid scheme even when the Peclet number is very high and the flow is at large angles to the grid.

Runchal, Akshai K.↗

NASA NTRS1986

Large eddy breakup devices as low Reynolds number airfoils

Turbulent drag reduction downstream of large-eddy breakup (LEBU) devices is analyzed from the viewpoint of low-Reynolds number airfoil aerodynamics. It is argued that the variability of results between different research labs is primarily due to low Reynolds number 'phenomena' associated with unsteady separation/transition of the LEBU device boundary layer. LEBU drag reduction is shown to be an extremely sensitive function of device microgeometry at the low Reynolds numbers of all current investigations, and by analogy with conventional low-Reynolds number airfoil testing, the conclusion is drawn that the full potential for LEBU drag reduction must be explored at chord Reynolds numbers of 300,000 and above.

Anders, John B.↗

NASA NTRS1987

Experimental study of low Reynolds number nozzles

Grisnik, Stanley P.↗

NASA NTRS1987

Influence of Reynolds number on forebody side forces for 3.5-diameter tangent-ogive bodies

Vortex asymmetries can arise on aircraft and missile forebodies at high angles of attack and have proven difficult to simulate in the wind tunnel because of a large array of parameters that can influence the test results. One of the most important of these parameters is Reynolds number. The current report compares, for tangent-ogive forebodies with fineness ratios of 3.5, flow patterns from oil-flow photographs to features in pressure distributions. The pressure data base is then used to illustrate the development of the sectional side force coefficient along both the tangent-ogive nose and an attached cylindrical afterbody for Reynolds numbers of 0.2, 0.8 and 3.8 million, based on maximum diameter, and angles of attack of 40, 50 and 60 deg. General commments concerning the effects of Reynolds number are presented, as well as an analysis of the effects of Reynolds number on the sectional side force coefficient near and at the apex of the pointed body. All data presented are for freestream Mach numbers on the order of 0.25.

Hall, Robert M.↗

NASA NTRS1988

A low speed wind tunnel investigation of Reynolds number effects on a 60-deg swept wing configuration with leading and trailing edge flaps

A low-speed wind tunnel test was performed to investigate Reynolds number effects on the aerodynamic characteristics of a supersonic cruise wing concept model with a 60-deg swept wing incorporating leading-edge and trailing-edge flap deflections. The Reynolds number ranged from 0.3 to 1.6 x 10 to the 6th, and corresponding Mach numbers from .05 to 0.3. The objective was to define a threshold Reynolds number above which the flap aerodynamics basically remained unchanged, and also to generate a data base useful for validating theoretical predictions for the Reynolds number effects on flap performance. This report documents the test procedures used and the basic data acquired in the investigation.

Rao, Dhanvada M.↗

NASA NTRS1989

Unsteady pressure measurements on a supercritical airfoil at high Reynolds numbers

Steady and unsteady pressures were measured on a 14 percent supercritical airfoil at transonic Mach numbers at Reynolds numbers from 6,000,000 to 35,000,000. Instrumentation techniques were developed to measure unsteady pressures in a cryogenic tunnel at flight Reynolds numbers. Experimental steady data, corrected for wall effects show very good agreement with calculations from a full potential code with an interacted boundary layer. The steady and unsteady pressures both show a shock position that is dependent on Reynolds number. For a supercritical pressure distribution at a chord Reynolds number of 35,000,000 laminar flow was observed between the leading edge and the shock wave at 45 percent chord.

Hess, R. W.↗

NASA NTRS1988

Topological numbering of features on a mesh

Assume a nxn binary image is given containing horizontally convex features; i.e., for each feature, each of its row's pixels form an interval on that row. The problem of assigning topological numbers to such features is considered; i.e., assign a number to every feature f so that all features to the left of f have a smaller number assigned to them. This problem arises in solutions to the stereo matching problem. A parallel algorithm to solve the topological numbering problem in O(n) time on an nxn mesh of processors is presented. The key idea of the solution is to create a tree from which the topological numbers can be obtained even though the tree does not uniquely represent the to the left of relationship of the features.

Atallah, Mikhail J.↗

NASA NTRS1989

Low Reynolds number numerical solutions of chaotic flow

Numerical computations of two-dimensional flow past an airfoil at low Mach number, large angle of attack, and low Reynolds number are reported which show a sequence of flow states leading from single-period vortex shedding to chaos via the period-doubling mechanism. Analysis of the flow in terms of phase diagrams, Poincare sections, and flowfield variables are used to substantiate these results. The critical Reynolds number for the period-doubling bifurcations is shown to be sensitive to mesh refinement and the influence of large amounts of numerical dissipation. In extreme cases, large amounts of added dissipation can delay or completely eliminate the chaotic response. The effect of artificial dissipation at these low Reynolds numbers is to produce a new effective Reynolds number for the computations.

Pulliam, Thomas H.↗

NASA NTRS1989

The effect of Mach number on the stability of a plane supersonic wave

The influence of compressibility on the mechanisms governing the various stages of transition in a supersonic wake is investigated. Results from linear stability theory are used to provide physical insights into the observed reduction in growth rate at high Mach numbers. A newly developed hybrid algorithm is used to solve the compressible inviscid linear disturbance equations. Growth rates for both antisymmetric and symmetric modes of two-dimensional and oblique waves are computed for a wide range of Mach numbers. Results from two and three-dimensional direct numerical simulations of a forced compressible time-developing wake are presented in order to understand the nonlinear stages of transition at high Mach numbers. Observed nonlinear growth rate comparisons are made for wakes at two different Mach numbers. The reduction in growth rate at high Mach numbers is explained by examining contour plots of baroclinic torques and the product of dilatation and vorticity.

Chen, Jacqueline H.↗

NASA NTRS1989

An improved correction algorithm for number density measurements made with the forward scattering spectrometer probe

A correction factor to the number density measured by the Forward Scattering Spectrometer Probe (FSSP) which compensates for dead time and coincidence errors was determined by calculating the probabilities of, and the average number of particles in, the six possible types of dead time and coincidence events. These probabilities and averages were calculated by means of a probabilistic model based on Poisson statistics. A Monte Carlo computer simulation of the FSSP operation was also carried out and the number density correction factor was compared with the Monte Carlo data. For an actual number density of 2000/cu cm, it was found that the measured number density was of the order of 300/cu cm.

Lock, James A.↗

NASA NTRS1989

Analysis of low Reynolds number separation bubbles using semiempirical methods

The formation and growth of transitional separation bubbles can significantly affect boundary-layer development on airfoils operating at low chord Reynolds numbers. Of primary concern is the change in boundary-layer thickness between laminar separation and turbulent reattachment. This can be estimated using semiempirical methods, such as the one devised by Horton (1968), which are based on solutions to the integral forms of the boundary-layer equations. The applicability of these methods at low Reynolds numbers was investigated using hot-wire measurements of bubbles formed on an NACA 66(3)-018 airfoil at chord Reynolds numbers of 50,000-200,000. The momentum thickness growth between separation and transition was found to be similar to that predicted for a laminar half-jet and appears to be influenced by the momentum thickness Reynolds number at separation. This parameter also was found to have a noticeable effect on the Reynolds number based on the length of a bubble's laminar portion.

Schmidt, Gordon S.↗

NASA NTRS1989

Comparison of conventional and adaptive wall wind tunnel results with regard to Reynolds number effects

A comparison of results from conventional and adaptive wall wind tunnels with regard to Reynolds number effects was carried out. The special objective of this comparison was to confirm or reject earlier conclusions, soley based on conventional wind tunnel results, concerning the influence of viscous effects on the characteristics of partially open wind tunnel walls, hence wall interference. The following postulations could be confirmed: (1) certain classes of supercritical airfoils exhibit a non-linear increase in lift which is, at least in part, related to viscous-inviscid interactions on the airfoil. This non-linear lift characteristic can erroneously be suppressed by sidewall interference effects in addition to being affected by changes in Reynolds number. Adaptive walls seem to relieve the influence of sidewall interference; (2) the degree of (horizontal) wall interference effects can be significantly affected by changes in Reynolds number, thus appearing as true Reynolds number effects; (3) perforated wall characteristics seem much more susceptible to viscous changes than the characteristics of slotted walls; here, blockage interference may be most severely influenced by viscous changes; and (4) real Reynolds number effects are present on the CAST 10-2/DOA 2 airfoil; they were shown to be appreciable also by the adaptive wall wind tunnel tests.

Stanewsky, E.↗

NASA NTRS1989

High Reynolds number tests of the CAST-10-2/DOA 2 transonic airfoil at ambient and cryogenic temper ature conditions

The transonic airfoil CAST 10-2/DOA 2 was investigated in several major transonic wind tunnels at Reynolds numbers ranging from Re=1.3 x 10(exp 6) to 45 x 10(exp 6) at ambient and cryogenic temperature conditions. The main objective was to study the degree and extent of the effects of Reynolds number on both the airfoil aerodynamic characteristics and the interference effects of various model-wind-tunnel systems. The initial analysis of the CAST 10-2 airfoil results revealed appreciable real Reynolds number effects on this airfoil and showed that wall interference can be significantly affected by changes in Reynolds number thus appearing as true Reynolds number effects.

Stanewsky, E.↗