Search NASA⌕ Search

SEARCH · Search NASA

Results for “object tracking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Equatorial Precession in the Control Software of the Ka-Band Object Observation and Monitoring Experiment

The Ka-Band Object Observation and Monitoring, or KaBOOM, project is designed mainly to track and characterize near Earth objects. However, a smaller goal of the project would be to monitor pulsars and study their radio frequency signals for use as a clock in interstellar travel. The use of pulsars and their timing accuracy has been studied for decades, but never in the Ka-band of the radio frequency spectrum. In order to begin the use of KaBOOM for this research, the control systems need to be analyzed to ensure its capability. Flaws in the control documentation leave it unclear as to whether the control software processes coordinates from the J200 epoch. This experiment will examine the control software of the Intertronic 12m antennas used for the KaBOOM project and detail its capabilities in its "equatorial mode." The antennas will be pointed at 4 chosen points in the sky on several days while probing the virtual azimuth and elevation (horizon coordinate) registers. The input right ascension and declination coordinates will then be converted separately from the control software to horizontal coordinates and compared, thus determining the ability of the control software to process equatorial coordinates.

Jakeman, Hali L.↗

Communications and tracking expert systems study

The original objectives of the study consisted of five broad areas of investigation: criteria and issues for explanation of communication and tracking system anomaly detection, isolation, and recovery; data storage simplification issues for fault detection expert systems; data selection procedures for decision tree pruning and optimization to enhance the abstraction of pertinent information for clear explanation; criteria for establishing levels of explanation suited to needs; and analysis of expert system interaction and modularization. Progress was made in all areas, but to a lesser extent in the criteria for establishing levels of explanation suited to needs. Among the types of expert systems studied were those related to anomaly or fault detection, isolation, and recovery.

Leibfried, T. F.↗

A Climatology and Life‐Cycle Characteristics of Atmospheric Fronts and Their Associated Precipitation

Abstract Atmospheric fronts are one of the main sources of mid‐latitude variability. We employ a novel method for identifying and tracking fronts and frontal precipitation. Thermal and dynamical variables are used to identify fronts as areal objects in space, which are tracked in time using the open‐source TempestExtremes software package. Precipitation objects are co‐located to identify frontal precipitation. The method is subjected to validation and sensitivity tests using manually curated data from the National Weather Service. Climatologies of fronts and frontal precipitation are computed from reanalysis and observations; fronts are present upwards of 14% of the time in the storm tracks, and represent the majority (up to 90%) of total and extreme precipitation. Novel aspects of the method are showcased through the lifetime characteristics of fronts across North America. Three sets of warm and cold fronts were discovered, and their duration, distance‐traveled, and translation velocity are examined. Plain Language Summary Mid‐latitude low‐pressure systems and weather fronts are important for our day‐to‐day experience of weather events, particularly in the mid‐latitudes. This work makes use of standardized atmospheric data and creates a method of automatically tracking these important atmospheric features and their precipitation to quantify their relative role in global precipitation. Weather fronts are persistent in the mid‐latitudes and are associated with the majority of precipitation–particularly the most intense precipitation. Trajectories of fronts over North America are categorized to create a set of archetypal fronts that occur in that region. The differences between these types of fronts are characterized. Key Points An automated, efficient, and skillful frontal detection algorithm is developed and validated Fronts contribute a larger fraction of extreme precipitation than all precipitation in mid‐latitude storm tracks Fronts across North America have substantial variation in characteristics depending on their origin location

extratropical cyclone↗

Laser Prevention of Earth Impact Disasters

We now believe that while there are about 2000 earth orbit crossing rocks greater than 1 kilometer in diameter, there may be as many as 100,000 or more objects in the 100m size range. Can anything be done about this fundamental existence question facing us? The answer is a resounding yes! We have the technology to prevent collisions. By using an intelligent combination of Earth and space based sensors coupled with an infrastructure of high-energy laser stations and other secondary mitigation options, we can deflect inbound asteroids, meteoroids, and comets and prevent them from striking the Earth. This can be accomplished by irradiating the surface of an inbound rock with sufficiently intense pulses so that ablation occurs. This ablation acts as a small rocket incrementally changing the shape of the rock's orbit around the Sun. One-kilometer size rocks can be moved sufficiently in a month while smaller rocks may be moved in a shorter time span.We recommend that the World's space objectives be immediately reprioritized to start us moving quickly towards a multiple option defense capability. While lasers should be the primary approach, all mitigation options depend on robust early warning, detection, and tracking resources to find objects sufficiently prior to Earth orbit passage in time to allow mitigation. Infrastructure options should include ground, LEO, GEO, Lunar, and libration point laser and sensor stations for providing early warning, tracking, and deflection. Other options should include space interceptors that will carry both laser and nuclear ablators for close range work. Response options must be developed to deal with the consequences of an impact should we move too slowly.

Campbell, J.↗

ELROI Extremely Low Resource Optical Identifier. A license plate for your satellite, and more.

ELROI (Extremely Low Resource Optical Identifier) is a license plate for your satellite; a small tag that flashes an optical identification code that can be read by a small telescope on the ground. The final version of the tag will be the size of a thick postage stamp and fully autonomous: you can attach it to everything that goes into space, including small cubesats and inert debris like rocket stages, and it will keep blinking even after the satellite is shut down, reliably identifying the object from launch until re-entry.

47 OTHER INSTRUMENTATION↗

SLS-PLAN-IT: A knowledge-based blackboard scheduling system for Spacelab life sciences missions

The primary scheduling tool in use during the Spacelab Life Science (SLS-1) planning phase was the operations research (OR) based, tabular form Experiment Scheduling System (ESS) developed by NASA Marshall. PLAN-IT is an artificial intelligence based interactive graphic timeline editor for ESS developed by JPL. The PLAN-IT software was enhanced for use in the scheduling of Spacelab experiments to support the SLS missions. The enhanced software SLS-PLAN-IT System was used to support the real-time reactive scheduling task during the SLS-1 mission. SLS-PLAN-IT is a frame-based blackboard scheduling shell which, from scheduling input, creates resource-requiring event duration objects and resource-usage duration objects. The blackboard structure is to keep track of the effects of event duration objects on the resource usage objects. Various scheduling heuristics are coded in procedural form and can be invoked any time at the user's request. The system architecture is described along with what has been learned with the SLS-PLAN-IT project.

Kao, Cheng-Yan↗

Sensor Spatial Distortion, Visual Latency, and Update Rate Effects on 3D Tracking in Virtual Environments

Several common defects that we have sought to minimize in immersing virtual environments are: static sensor spatial distortion, visual latency, and low update rates. Human performance within our environments during large amplitude 3D tracking was assessed by objective and subjective methods in the presence and absence of these defects. Results show that 1) removal of our relatively small spatial sensor distortion had minor effects on the tracking activity, 2) an Adapted Cooper-Harper controllability scale proved the most sensitive subjective indicator of the degradation of dynamic fidelity caused by increasing latency and decreasing frame rates, and 3) performance, as measured by normalized RMS tracking error or subjective impressions, was more markedly influenced by changing visual latency than by update rate.

Ellis, S. R.↗

Astrometric Follow-Up of Faint Near Earth Objects

The observing program at Mt. Hopkins using the 48" reflector and funded by the Near- Earth Object Observation Program continues to excel. As in the past, all requested observing time was granted. Minor improvements continue to be made. For example, the telescope is set up to track and non-sidereal rates. This allows the user to track on the target object, rather than relying exclusively on the shift- and-stack technique. Other improvements made by the staff include automatic focus routines, automatic seeing-measurement routines, and improvement in dome seeing and mirror stabilization. The net result is better focus, better seeing, and the ability to expose longer in order to acquire the faintest and most important objects. During the proposal period, this program ranked again very high worldwide in terms of faint Near Earth Objects observed. During this latest proposal cycle, fewer objects were observed than previous cycles, but this was due to the strict targeting of only the faintest observable objects. The follow-up programs of observatory codes 926 (led by P. Holvorcem) and 291 (led by Dr. B. McMillan) have greatly increased their capacity, and as a result less bright objects are in urgent need of follow-up than in years past. Even with this new object selection and additional competition, code 696 still ranked second to code 291 in terms of objects observed fainter than V = 20. Minimal scripting is now in place to allow the telescope to run autonomously for 30-45 minutes at a time.

Morgan, T.↗

Object Locating System

A portable system is provided that is operational for determining, with three dimensional resolution, the position of a buried object or approximately positioned object that may move in space or air or gas. The system has a plurality of receivers for detecting the signal front a target antenna and measuring the phase thereof with respect to a reference signal. The relative permittivity and conductivity of the medium in which the object is located is used along with the measured phase signal to determine a distance between the object and each of the plurality of receivers. Knowing these distances. an iteration technique is provided for solving equations simultaneously to provide position coordinates. The system may also be used for tracking movement of an object within close range of the system by sampling and recording subsequent position of the object. A dipole target antenna. when positioned adjacent to a buried object, may be energized using a separate transmitter which couples energy to the target antenna through the medium. The target antenna then preferably resonates at a different frequency, such as a second harmonic of the transmitter frequency.

Arndt, G. Dickey↗

Deterministic Simulation of First-Order Scattering in a Clinical X-ray Computed Tomography Scanner - Paper 81

In nondestructive testing (NDT) and medical diagnostic x-ray imaging (photon energy<140 keV), scattered x-ray caused by Compton and Rayleigh scattering should be eliminated. Scattered x-ray photons reduce image contrast, increase image noise, and introduce artifact into the reconstructed computed tomography (CT) images. In cone-beam CT, where the coverage of the x-ray beam and the area of the detector are significantly larger than those in fan-beam CT, x-ray photon scatter is one of the major sources of image degradation. The artifacts caused by scattered x-ray photon can be divided into two categories: 1) low spatial frequency scatter profile adds a positive bias to the detected radiation signal, thus reducing the effective attenuation of the imaged object, resulting in a negative bias in the measured linear attenuation coefficient in the image; 2) a high spatial frequency scatter profile causes a differential artifact, such as shading in uniform regions. A real x-ray scan is composed of both low and high frequency scatter profiles. Thus, the key to a successful scatter correction is the ability to accurately capture the scatter profile of a real x-ray imaging scan. The most accurate method for estimating a scatter profile is the Monte Carlo simulation. However, the computation cost of the Monte Carlo method makes it unfeasible for simulating real and complex scan geometries in clinical settings. A practical yet accurate scatter profile estimation method is through ray tracing techniques, where the scatter profiles are computed by tracking rays through the object's volume. The x-ray from the source is tracked when it interacts with the material in the volume. The interaction creates scattered x-rays, in all possible directions. These rays are again either attenuated or scattered, creating cascaded scatter events. In x-ray CT, the first-order scattering (where only one scatter interaction is encountered) accounts for the most severe image artifacts since this first-order scatter contains a high frequency component of the scatter profile. Previous studies have shown that ray tracing techniques are quite effective in simulating the contribution of first-order scattering in radiological images. In this study, a similar ray tracing technique is applied to simulate the scatter profile of a real x-ray computed tomography (CT) scan in clinical settings. A good agreement has been found between the simulated scatter profile and the experimental measurement result. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗

Optimal nonlinear estimation for aircraft flight control in wind shear

The most recent results in an ongoing research effort at Princeton in the area of flight dynamics in wind shear are described. The first undertaking in this project was a trajectory optimization study. The flight path of a medium-haul twin-jet transport aircraft was optimized during microburst encounters on final approach. The assumed goal was to track a reference climb rate during an aborted landing, subject to a minimum airspeed constraint. The results demonstrated that the energy loss through the microburst significantly affected the qualitative nature of the optimal flight path. In microbursts of light to moderate strength, the aircraft was able to track the reference climb rate successfully. In severe microbursts, the minimum airspeed constraint in the optimization forced the aircraft to settle on a climb rate smaller than the target. A tradeoff was forced between the objectives of flight path tracking and stall prevention.

Mulgund, Sandeep S.↗

Standardizing Navigation Data: A Status Update

This paper presents the work of the Navigation Working Group of the Consultative Committee for Space Data Systems (CCSDS) on development of standards addressing the transfer of orbit, attitude and tracking data for space objects. Much progress has been made since the initial presentation of the standards in 2004, including the progression of the orbit data standard to an accepted standard, and the near completion of the attitude and tracking data standards. The orbit, attitude and tracking standards attempt to address predominant parameterizations for their respective data, and create a message format that enables communication of the data across space agencies and other entities. The messages detailed in each standard are built upon a keyword = value paradigm, where a fixed list of keywords is provided in the standard where users specify information about their data, and also use keywords to encapsulate their data. The paper presents a primer on the CCSDS standardization process to put in context the state of the message standards, and the parameterizations supported in each standard, then shows examples of these standards for orbit, attitude and tracking data. Finalization of the standards is expected by the end of calendar year 2007.

VanEepoel, John M.↗

Sharp Interface Tracking in Rotating Microflows of Solvent Extraction

The objective of this project is to develop a specialized sharp interface tracking simulation capability for predicting interaction of micron-sized drops and bubbles in rotating flows relevant to optimized design of contactor devices used in solvent extraction processes of spent nuclear fuel reprocessing. The primary outcomes of this project include the capability to resolve drops and bubbles micro-hydrodynamics in solvent extraction contactors, determining from first principles continuum fluid mechanics how micro-drops and bubbles interact with each other and the surrounding shearing fluid for realistic flows. In the near term, this effort will play a central role in providing parameters and insight into the flow dynamics of models that average over coarser scales, say at the millimeter unit length. In the longer term, it will prove to be the platform to conduct full-device, detailed simulations as parallel computing power reaches the exaflop level. The team will develop an accurate simulation tool for flows containing interacting droplets and bubbles with sharp interfaces under conditions that mimic those found in realistic contactor operations. The main objective is to create an off-line simulation capability to model drop and bubble interactions in a domain representative of the averaged length scale. The technical approach is to combine robust interface tracking software, subgrid modeling, validation quality experiments, powerful computational hardware, and a team with simulation modeling, physical modeling and technology integration experience. Simulations will then fully resolve the microflow of drops and bubbles at the microsecond time scale. This approach is computationally intensive but very accurate in treating important coupled physical phenomena in the vicinity of interfaces. The method makes it possible to resolve spatial scales smaller than the typical distance between bubbles and to model some non-equilibrium thermodynamic features such as finite critical tension in cavitating liquids

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Impact Imperative: A Space Infrastructure Enabling a Multi-Tiered Earth Defense

Impacting at hypervelocity, an asteroid struck the Earth approximately 65 million years ago in the Yucatan Peninsula a m . This triggered the extinction of almost 70% of the species of life on Earth including the dinosaurs. Other impacts prior to this one have caused even greater extinctions. Preventing collisions with the Earth by hypervelocity asteroids, meteoroids, and comets is the most important immediate space challenge facing human civilization. This is the Impact Imperative. We now believe that while there are about 2000 earth orbit crossing rocks greater than 1 kilometer in diameter, there may be as many as 200,000 or more objects in the 100 m size range. Can anything be done about this fundamental existence question facing our civilization? The answer is a resounding yes! By using an intelligent combination of Earth and space based sensors coupled with an infrastructure of high-energy laser stations and other secondary mitigation options, we can deflect inbound asteroids, meteoroids, and comets and prevent them &om striking the Earth. This can be accomplished by irradiating the surface of an inbound rock with sufficiently intense pulses so that ablation occurs. This ablation acts as a small rocket incrementally changing the shape of the rock's orbit around the Sun. One-kilometer size rocks can be moved sufficiently in about a month while smaller rocks may be moved in a shorter time span. We recommend that space objectives be immediately reprioritized to start us moving quickly towards an infrastructure that will support a multiple option defense capability. Planning and development for a lunar laser facility should be initiated immediately in parallel with other options. All mitigation options are greatly enhanced by robust early warning, detection, and tracking resources to find objects sufficiently prior to Earth orbit passage in time to allow significant intervention. Infrastructure options should include ground, LEO, GEO, Lunar, and libration point laser and sensor stations for providing early warning, tracking, and deflection. Other options should include space interceptors that will carry both laser and nuclear ablators for close range work. Response options must be developed to deal with the consequences of an impact should we move too slowly.

Campbell, Jonathan W.↗

Debris impact on Earth-orbiting spacecraft

The accumulation of Earth-orbiting space debris leads to important new design considerations. Some 5,000 orbiting objects, many of them explosion fragments, are currently being tracked and future collision of these objects with each other is predicted. These collisions will occur at high velocities. Each collision will be explosive, ejecting thousands, of new orbiting objects, in turn increasing the frequency of future collisions. The debris population may thus become self-regenerative, and the future flux of orbiting debris will exceed that of meteoroids. As a result, a large space structure in Earth-orbit for several years has a significant probability of impact by debris objects. As a design problem, debris impact is significantly different from meteoroid impact. Protection against such large objects may require structural measures. The consideration of debris impact in the design of large, Earth-orbiting spacecraft is recommended.

Smith, D. G.↗

Precursor active galaxies and the cosmic X-ray background

It is argued that the cosmic X-ray background (CXB) is not dominated by sources that are usual active galaxies or quasars. A comparable number of objects, young galaxies at z approximately 4 containing massive black holes surrounded by hot optically thin accretion disks, constitute the precursor active galaxies (PAG) postulated here for producing the thermal type spectrum required for the CXB. An evolutionary track for such PAG objects is described which would lead to the active galaxies observed as individual nonthermal sources. Unresolved emission from active galaxies at z 1 could then readily account for most of the nonthermal background observed in the gamma ray band.

Boldt, E. A.↗

NORAD satellite tracking

NORAD routinely tracks about 6000 orbiting objects. During the last 30 days of orbital time, prior to reentry, special perturbations are used in the orbital update procedure. Besides routine orbit determination, NORAD does special tasks such as predicting satellite orbit conjunctions within 20 km, ephimerides of weather satellites, satellite decay predictions and other studies. Since their mission is operational, they do not store the data from their analyses. The ballistic coefficient is not known for most of the orbiting objects. If a ballistic coefficient were derived that was consistent with one density model, it might give erroneous results if used with a different density model. Given the ballistic coefficient, density values could, in principle, be obtained from their tracking data. The densities would represent an integrated mean over the orbital path near perigee. They would be model dependent and would not necessarily represent the real density. In summary, the primary need is for reliable forecasts of solar flux (F10.7) and geomagnetic activity (Ap) in the 1 to 4 week time scale. Forecasts over longer time spans would also be useful for special projects.

Liu, Joseph J. F.↗

Space Object Query Tool

STI is for a fact sheet on the Space Object Query Tool being created by the MDC. When planning launches, NASA must first factor in the tens of thousands of objects already in orbit around the Earth. The number of human-made objects, including nonfunctional spacecraft, abandoned launch vehicle stages, mission-related debris and fragmentation debris orbiting Earth has grown steadily since Sputnik 1 was launched in 1957. Currently, the U.S. Department of Defenses Joint Space Operations Center, or JSpOC, tracks over 15,000 distinct objects and provides data for more than 40,000 objects via its Space-Track program, found at space-track.org.

Space congestion↗