Search NASA⌕ Search

SEARCH · Search NASA

Results for “open circuit”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

SnS Homojunction Solar Cell with n-Type Single Crystal and p-Type Thin Film

Herein, a pn homojunction SnS solar cell is fabricated for the first time by the deposition of p-type SnS polycrystalline thin films on the recently reported large n-type SnS single crystals. The p-type thin films consist of columnar grains that grow along the <100> direction, which is the same orientation as the n-type single crystal. In addition, the interface of the pn homojunctions is void-free and compositionally sharp. The SnS homojunction solar cell achieves an open-circuit voltage (VOC) of 360 mV, which is as large as the highest VOC of previously reported SnS-based heterojunction solar cells. The built-in potential of the homojunction cell is 0.92 eV, which is close to the bandgap energy of SnS (≈1.1 eV), and larger than reported for heterojunctions (≈0.7 eV). The resulting 1.4% conversion efficiency (n) of the homojunction solar cell is smaller than the record 4–5% in heterojunctions, mainly due to the low short-circuit current density (J SC ) of 7.5 mA cm -2 . Once the device structure of the homojunction cell is optimized to efficiently collect the photogenerated carriers and achieve a comparable J SC as the conventional heterojunction cells (≈25 mA cm -2 ), high n exceeding 4–5% will be realized with improving the VOC.

14 SOLAR ENERGY↗
DOE OSTI2021

Identification of Recombination Losses in CdSe/CdTe Solar Cells from Spectroscopic and Microscopic Time-Resolved Photoluminescence

Due to the lowest-cost and best reliability, CdTe solar cells are the leading thin-film photovoltaic technology. Increasing open-circuit voltage by reducing recombination represents the most promising path toward further improvements. Analysis is needed to identify limitations that cause efficiency losses. To achieve this goal for Cu-doped CdSe/CdTe solar cells, time-resolved spectroscopy and microscopy are developed and applied. Recombination lifetimes and radiative efficiency identify that defect-mediated recombination is the dominant voltage loss mechanism. When carrier lifetimes are averaged over many crystalline grains, they increase from 180 to 430 ns when Al2O3 is applied to the back contact. The quasi-Fermi-level splitting correspondingly increases from 880–905 to 906–931 mV, indicating a pathway to overcome the long-standing 900 mV voltage limitation. However, the dominant recombination losses are attributed to the absorber bulk. From microscopic carrier lifetime measurements, it is identified that space charge fields due to charged grain boundaries (GBs) lead to recombination in the CdTe absorber bulk. At high injection, GB space charge fields are screened, but that occurs above 1 Sun excitation conditions. Alloying with selenium in the near-interface CdSeTe absorber region reduces GB losses and is identified as one of the factors leading to high radiative and power conversion efficiency.

14 SOLAR ENERGY↗
DOE OSTI2021

Exceeding 200 ns Lifetimes in Polycrystalline CdTe Solar Cells

CdTe photovoltaics has achieved one of the lowest levelized costs of electricity among all energy sources. However, for decades, carrier lifetimes have been inferior to those of other prevalent solar cell materials. This quality has inhibited common methods to improve solar cell efficiency such as back-surface fields, electron reflectors, or bifacial solar cells. In this work, a significant increase in carrier lifetime to values exceeding 200 ns in fully functional CdTe solar cells is demonstrated. The increased lifetime is achieved by large CdSeTe grains at the absorber/emitter interface, intragrain passivation in the absorber layer, and chemical passivation by forming nanoscale oxidized tellurium species at the transparent conducting oxide interface. The carrier lifetime is correlated to the open-circuit voltage and enables paths for back-surface manipulation and novel cell architectures to further improve CdTe photovoltaic performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Investigation of Gallium–Boron Spin-On Codoping for poly-Si/SiO x Passivating Contacts

A doping technique for p-type poly-Si/SiOx passivating contacts using a spin-on method for different mixtures of Ga and B glass solutions is presented. Effects of solution mixing ratios on the contact performance (implied open circuit voltage iV oc , contact resistivity ..rho..c) are investigated. For all as-annealed samples at different drive-in temperatures, increasing the percentage of Ga in the solution shows a decrement in iV oc (from ~680 to ~610 mV) and increment in ..rho..c (from ~3 to ~800 mO cm 2 ). After a hydrogenation treatment by depositing a SiN x /AlO x stack followed by forming gas annealing, all samples show improved iVoc (~700 mV with Ga-B co-doped, and ~720 mV with all Ga). Interestingly, when co-doping Ga with B, even a small amount of B in the mixing solution shows negative effects on the surface passivation. Active and total dopant profiles obtained by electrical capacitance voltage and secondary-ion mass spectrometry measurements, respectively, reveal a relatively low percentage of electrically-active Ga and B in the poly-Si and Si layers. Overall, these results help understand the different features of the two dopants: a low ρ c with B, a good passivation with Ga, their degree of activation inside the poly-Si and Si layers, and the annealing effects.

14 SOLAR ENERGY↗
DOE OSTI2021

Long-Term Degradation of Passivated Emitter and Rear Contact Silicon Solar Cell under Light and Heat

Advanced designs enable high-efficiency solar cells; however, more complex structures create new long-term stability concerns. Herein, the long-term degradation processes affecting advanced silicon solar cells using laboratory-based illumination and heating over hundreds of hours are investigated. The activation energy for the degradation of voltage is estimated and the degradation rates to normal solar cell operating temperature ranges are extrapolated. The cell degradation observed at high temperatures in the lab is kinetically similar to the process affecting field-deployed modules contributing to 0.37% year-1 of annualized degradation. Electroluminescence and photoluminescence mapping show that the degradation is dominated by minority carrier lifetime reduction. Suns-open-circuit voltage and light beam-induced current results indicate that the degradation could result from passivation degradation at the surface or defect formation in the near-subsurface region, leading to increased minority carrier recombination. This work highlights a long-term degradation process under elevated temperature and illumination that may continue to affect cells in an irreversible manner that is separate from recoverable light-induced degradation and light- and elevated temperature-induced degradation.

14 SOLAR ENERGY↗
DOE OSTI2021

How Useful are Conventional I–Vs for Performance Calibration of Single- and Two-Junction Perovskite Solar Cells? A Statistical Analysis of Performance Data on ≈200 Cells from 30 Global Sources

As perovskite photovoltaics (PV) advance from the laboratory to commercial prototypes, their accurate and reliable performance testing is becoming increasingly important. The well-documented dynamic response of perovskite solar cells to an external applied voltage has led to the development of steady-state performance measurement methods; however, these methods have not been widely adopted by the perovskite PV community. A key reason for this is that steady-state measurement methods take tens of minutes to complete, as opposed to conventional "fast" current-voltage (I-V) measurements usually lasting a few seconds. Fast I-Vs arise from a snapshot, almost always not a steady-state condition of the device; however, given their widespread use, the question arises: how do performance parameters of perovskite PV compare when measured with fast I-V and with a steady-state method? Results compiled from approximately 200 perovskite PV cells, including single junction, and two-terminal perovskite-perovskite and perovskite-Si tandems, show that fast I-Vs can provide a useful measure of the open-circuit voltage of the devices, while the short-circuit current and the overall efficiency can be widely misestimated. Here, the implications of these findings on performance testing protocols are discussed and possible options for fast and accurate testing of perovskite PV are proposed.

14 SOLAR ENERGY↗
DOE OSTI2022

Large-Area (Ag,Cu)(In,Ga)Se 2 Thin-Film Solar Cells with Increased Bandgap and Reduced Voltage Losses Realized with Bulk Defect Reduction and Front-Grading of the Absorber Bandgap

The 1.24 eV bandgap, 18.8% power conversion efficiency Ag-alloyed chalcopyrite (Ag,Cu)(In,Ga)Se 2 (ACIGS) solar cells are characterized to relate voltage and efficiency improvements to electro-optical (EO) characteristics. Shockley-Read-Hall recombination center defect density, identified and characterized through deep level transient spectroscopy and time-resolved photoluminescence (TRPL), is reduced through potassium and copper treatment optimization. Concomitantly, longer minority carrier lifetimes are achieved, which increases open-circuit voltage (V OC ). Near-conduction band defects associated in earlier studies with light-induced current instability are also mitigated. Analysis of charge-carrier dynamics after single- and two-photon excitation is used to separate recombination at the front interface and in the absorber bulk. From TRPL decay simulations, the authors estimate ranges of key solar cell material characteristics: bulk carrier lifetime T bulk = 110-210 ns, charge-carrier mobility u = 110-160 cm 2 V -1 s -1 , and front interface recombination velocity S front = 700-1050 cm s -1 . This lowest-reported S front for ACIGS absorbers originates from the notched conduction band grading, which also makes the impact of the back interface recombination negligible. It is suggested in the results that solar cell performance enhancements can be made most readily with two distinct strategies: improving device architecture and reducing semiconductor defect densities. Using these approaches, power conversion efficiency in large-area solar cells is improved by 1.1% absolute.

14 SOLAR ENERGY↗
DOE OSTI2022

Blade Coating Inverted Perovskite Solar Cells with Vacuum-Assisted Nucleation Based on Bottom Quasi-2D Passivation

Metal halide perovskite solar cells (PSCs) attract an enormous attention because of their high power conversion efficiency (PCE) and low fabrication cost. However, their commercialization is limited by fabricating highly efficient large-area solar cells. Controlling the morphology and crystallization of perovskite for large-area fabrication is difficult but important. Here, in this work, a vacuum-assisted approach is developed to obtain mirror-like, pinhole-free, highly crystalline, and uniform blade-coated perovskite films, without the use of antisolvent and air knife. This method can be a universal approach for various perovskite compositions. Meanwhile, the phenethylammonium iodide passivation effect at the top and bottom interfaces of perovskite layer based on FTO/NiO x /perovskite/C 60 /BCP/Cu inverted p-i-n structure is systematically investigated. The optimized device fabricated by blade coating under an ambient environment exhibits the champion PCE of 20.7% and is among the top few records of blade coating inverted structure based on NiOx hole transport layer. The encapsulated device retains 97% of its maximum efficiency under open-circuit condition after 1000 h of photostability test in an ambient environment at room temperature with a relative humidity of 40–60%. Herein, low-cost, easy, and reproducible strategies to fabricate efficient and stable blade-coated PSCs are demonstrated.

14 SOLAR ENERGY↗
DOE OSTI2023

Band Bending at CdTe Solar Cell Contacts: Correlating Electro‐Optical and X‐Ray Photoelectron Spectroscopy Analyses of Thin Film Solar Cells

With the semiconductor bulk properties reaching target values for highly efficient solar cells, efforts are applied to reduce losses at solar cell interfaces and contacts. Advances in understanding back contacts in thin‐film polycrystalline CdTe solar cells, a leading thin‐film PV technology, are reported. By using X‐Ray photoelectron spectroscopy, Kelvin probe spectroscopy, time‐ and energy‐resolved photoluminescence, defects at the back contact are analyzed. Densities of recombination centers and charged defects that induce near‐back‐contact band bending, both resulting in recombination losses, were estimated. Electro‐optical and surface analysis results are integrated into a device model, simulating the performance of CdSeTe/CdTe solar cells with 902 mV open circuit voltage.

14 SOLAR ENERGY↗
DOE OSTI2023

Thermomechanical Cleave of Polycrystalline CdTe Solar Cells and its Applications: A Review

One of the primary research challenges for cadmium telluride (CdTe) solar cells is addressing its open‐circuit voltage ( V OC ) deficit. While theoretical studies and single crystal work show V OC > 1 V is possible, devices remain stubbornly low at ≈800–900 mV. As absorber opto‐electronic properties (e.g., hole density, carrier lifetime) are improved, device modeling suggests that interfaces become limiting. Because CdTe‐based devices are typically grown in the superstrate configuration, the back interface is relatively accessible for manipulation and study, while the front interface (i.e., the heterojunction region) is buried under microns of material and inaccessible. NREL has developed a novel technique to thermomechanically cleave polycrystalline CdTe device stacks directly at the front interface, enabling characterization and controlled manipulation of this important region. Herein, recent work, primarily from NREL, will be reviewed, including considerations for achieving successful delamination; key scientific discoveries about the front interface that have been enabled by this technique; and practical applications, such as flexible, low‐cost solar with high power‐to‐weight ratio.

14 SOLAR ENERGY↗
DOE OSTI2024

Comprehensive Study of Carrier Recombination in High‐Efficiency CdTe Solar Cells Using Transient Photovoltage

Cadmium telluride (CdTe) solar cells represent a commercially successful photovoltaic technology, with an annual production capacity approaching 20 GW. However, improving the open-circuit voltage (V OC ) remains challenging. This study aims to deepen the understanding of charge carrier recombination in CdTe solar cells and to explore alternative dynamical characterization methods that address the limitations found in conventionally used time-resolved photoluminescence for CdTe solar cells. Transient photovoltage and transient photocurrent techniques are utilized to investigate charge carrier dynamics under conditions resembling real-world solar cell operation. The results reveal that an effective nonradiative recombination lifetime of 580 ns dominates the charge dynamics at VOC values below 850 mV. Above this threshold, radiative recombination becomes significant, with a radiative recombination coefficient of 1.1 × 10 −9 cm 3 s −1 . Additionally, the stationary charge carrier density at 1 sun is determined to be around 1 × 10 14 cm −3 . By accurately determining both radiative and nonradiative recombination, this work provides a comprehensive understanding of carrier dynamics in high-performing CdTe devices and paves the way for improving the V OC and performance of CdTe solar cells.

CdTe solar cells↗
DOE OSTI2025

Monocrystalline CdSeTe/MgCdTe Double‐Heterostructure Solar Cells

This article reports monocrystalline CdSeTe/MgCdTe double‐heterostructure (DH) solar cells with varying Se compositions in the absorber layers that are grown on InSb substrates by using molecular beam epitaxy. The Se composition in the samples studied is determined to be 4%–11% through high‐resolution X‐ray diffraction (XRD) and photoluminescence measurements. Increased Se incorporation induces higher defect density attributed to increased lattice mismatch, and mixed‐phase formation due to the small difference in formation energies between the wurtzite and zinc blende phases of CdSe, which causes stacking faults and grain boundaries. Devices are fabricated by directly depositing an n‐type indium tin oxide (ITO) layer on the CdSeTe/MgCdTe DHs followed by Ag metal contacts. Reduced bandgap is observed in solar cells with increased Se composition. The devices with an absorber containing 4% Se exhibit an average open‐circuit voltage ( V OC ) of 0.925 V, a short‐circuit current density ( J SC ) of 23.4 mA/cm 2 , a fill factor ( FF ) of 0.650 and an efficiency of 14.1% without anti‐reflection coating. Absorbers with higher Se compositions result in poor device performance, mainly attributed to high defect density in the materials.

Ju, Zheng [Center for Photonics Innovation Arizona↗
DOE OSTI2022

Chlorination of uranium metal in molten NaCl-CaCl 2 via bubbling HCl

Molten chloride salt fast reactors (MCFRs) will require UCl 3 dissolved in molten salt mixtures as fuel for nuclear fission. For infusing the salt with UCl 3 , bubbling HCl into NaCl-CaCl 2 in contact with U metal was investigated. The reaction was run up to 9 h and yielded U concentration up to 0.652 wt.%. Open circuit potential between a W electrode and Ag/AgCl reference electrode yielded a potential consistent with uranium existing as U(III) in the salt. Furthermore, this demonstrates that HCl can be a very effective chlorinating agent to infuse MCFR fuel with UCl 3 starting from U metal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

On the Impact of Mechanics on Electrochemistry of Lithium-Ion Battery Anodes

Abstract Models exploring electrochemistry-mechanics coupling in liquid electrolyte lithium-ion battery anodes have traditionally incorporated stress impact on thermodynamics, bulk diffusive transport, and fracture, while stress-kinetics coupling is more explored in the context of all solid-state batteries. Here, we showcase the existence of strong link between active particle surface pressure and reaction kinetics affecting performance even in liquid electrolyte systems. Traction-free and immobile particle surface mechanical boundary conditions are used to delineate the varying pressure magnitudes in graphite host during cycling. Both tensile and compressive stresses are generated in traction-free case, while a fixed surface subjects the entire particle to a compression state. Pressure magnitudes are nearly two to three orders of magnitude higher for the latter resulting in significant depression of open circuit potential and improvement of exchange current densities compared to stress-free state. The results demonstrate the need for incorporating stress-kinetics linkage in models and provide a rationale for putting battery electrodes under compression to improve kinetics.

25 ENERGY STORAGE↗
DOE OSTI2020

Mass production of high-performance single atomic FeNC electrocatalysts via sequenced ultrasonic atomization and pyrolysis process

Mass production of highly efficient, durable, and inexpensive single atomic catalysts is currently the major challenge associated with the oxygen reduction reaction (ORR) for fuel cells. In this study, we develop a general strategy that uses a simple ultrasonic atomization coupling with pyrolysis and calcination process to synthesize single atomic FeNC catalysts (FeNC SACs) at large scale. The microstructure characterizations confirm that the active centers root in the single atomic Fe sites chelating to the four-fold pyridinic N atoms. The identified specific Fe active sites with the variable valence states facilitate the transfer of electrons, endowing the FeNC SACs with excellent electrochemical ORR activity. The FeNC SACs were used as cathode catalysts in a homemade Zn-air battery, giving an open-circuit voltage (OCV) of 1.43 V, which is substantially higher than that of commercial Pt/C catalysts. This study provides a simple approach to the synthesis of single atomic catalysts at large scale.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tailoring activity of iron phthalocyanine by edge-nitrogen sites induced electronic delocalization

Fe-N-C catalysts have been recognized as the most satisfactory candidates alternatively to Pt-based catalysts for oxygen reduction reaction (ORR). However, fine-tailoring of their intrinsic ORR catalytic activity still remains a great challenge due to the inferior accessibility and intrinsic activity of FeN x moieties. Herein, one order of magnitude activity enhancement of pristine Fe-N-C through cooperating with nitrogen-doped carbon micro-flower is achieved. The axial coordination effect between Fe active center and nitrogen atoms in support can break the electronic distribution symmetry of FeN x moieties and induce the electron delocalization on Fe active center and the electron localization on N, respectively, which favor the adsorption behavior of *OH intermediate. As a result, the catalyst exhibits a remarkable half-wave potential of 0.9 V and a high kinetic current density of 74.04 mA cm -2 at 0.85 V. In addition, when utilized as a cathode catalyst of liquid Zn-air batteries (ZABs), it possesses excellent electrochemical performance, for example, a high open circuit voltage (OCV) and peak power density of 1.59 V and 170.09 mW cm -2 , respectively. In conclusion, this work provides a new understanding into the activity enhancement mechanism of Fe-N-C catalysts, and inspires electronic delocalization of active sites for adjusting catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A 3D porous honeycomb carbon as Na-ion battery anode material with high capacity, excellent rate performance, and robust stability

Motivated by the synthesis of three-dimensional (3D) honeycomb carbon structures and the subsequent theoretical prediction of an energetically more favorable hexagonal carbon phase composed of 28 carbon atoms in the unit cell (hC28) with ordered pores, excellent mechanical properties, and metallic feature, we explore its potential for a Na-ion battery (NIB) anode material. Using density functional theory based calculations, we find that hC28 is a promising candidate whose specific capacity of 717 mAh/g is almost three times larger than that of hard carbon (~250 mAh/g). In addition, migration barrier of Na ions along the honeycomb channel is only 0.08 eV and the volume change during the charging/discharging process is merely 2.30%, which are much less than those of other carbon-based NIB anode materials. The average voltage is also low (0.36 eV) which can provide high operating voltage when connected to the cathode. Finally, these encouraging results would pave the way towards the development of hC28 as NIB anode with high capacity, excellent rate performance, low open-circuit voltage, and long-term cycle life.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hex-C 558 : A new porous metallic carbon allotrope for lithium-ion battery anode

Due to the limited specific capacity of graphite anodes in lithium-ion batteries (LIBs), it is imperative to find alternatives with better performance. Here in this work, we propose, for the first time, a three dimensional (3D) porous metallic 5-5-8 carbon monolith with hexagonal lattice as a potential candidate. With 5-5-8 carbon nanoribbon as the building block, this material, named Hex-C558, goes beyond graphene-nanoribbon-based 3D porous carbon structures. Using first-principles calculations, we show that Hex-C 558 is not only dynamically and thermally stable, but also is energetically more favorable than many other theoretically predicted carbon allotropes. More importantly, Hex-C 558 is metallic with ordered ionic conducting channels and possesses a low mass density of 1.05 gcm -3 , exhibiting great potential for ion-battery applications. As an anode for LIBs, Hex-C558 possesses a large specific capacity of 591 mAhg -1 , low diffusion energy barrier of 0.27 eV (at low Li concentration) and 0.52 eV (at high Li concentration), a low open-circuit voltage of 0.51 V, and a small volume change of 2.4%. This work provides a new route for the design and synthesis of novel carbon materials for battery applications by using pentagon-based building units.

36 MATERIALS SCIENCE↗