Search NASA⌕ Search

SEARCH · Search NASA

Results for “silicate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Comparative geochemistry of flowback chemistry from the Utica/Point Pleasant and Marcellus formations

Flowback/Produced fluid samples were collected from several wells from two Utica/Point Pleasant (UPP) sites (UPPW and UPPS) in Ohio, and one Marcellus (Marcellus Shale Energy and Environment Laboratory (MSEEL)) site in West Virginia over a period of approximately two years. Although these formations have different ages, depositional environments, diagenetic histories, and geochemical and mineralogical compositions (i.e. the UPP is significantly more carbonate rich than the Marcellus which is more siliceous), analysis of trends in fluid species over time shows that, overall, the TDS and major solubilized elements (Na, Ca, Cl) in the UPP and Marcellus brines are remarkably similar. Total dissolved solutes (TDS) in these brines ranged from approximately 40 to 250 g/L salt, and in general, concentrations increased with time elapsed since natural gas well completion and stimulation. The behavior of Na, Br, and Cl suggests that the produced water signatures from these formations are largely derived from the native formational brines which display evidence of originating from evaporated seawater. There is a strong correlation between Cl and Br, indicating that both species behave conservatively, and the similarity among each of these brines suggests no appreciable contribution of salt from halite dissolution because Br is excluded from the halite structure. Cl/Br ratios in the brines range from ~80 to 120 (mg/L/mg/L). Other elements, such as K, which readily reacts between fluids and ion exchange sites on clays, generally exhibit conservative behavior for an individual site, but show significant variations among each of the different well pads. The concentrations of Sr and Ba vary dramatically among well sites, and increase with respect to Cl- over time, suggesting increasing solubilization, presumably from desorption from clay minerals or dissolution of carbonates or sulfates from the source formation(s). The UPPW well site has very low Ba due to high-sulfate input fluid, which resulted in precipitation of barite/celestite in the brines. In contrast the UPPS well site had elevated Sr (~ 3500 mg/L), presumably due to the use of Sr-rich recycled brine used in hydraulic fracturing. The Marcellus site had the highest Ba concentrations (up to 10 g/L) and highest Ba/Sr ratios in the fluids, due to the high concentration of barium in the Marcellus target (~ 1000 ppm, as compared to ~200 ppm in the UPP). These observations suggest that solutes in the FP fluids are derived from native brines, water-rock interactions that have occurred over geologic time scales, as well as some contribution from contemporaneous reactions in the subsurface. The results also show that the composition of the injected fluid can influence flowback fluid chemistry and possibly production efficiency.

58 GEOSCIENCES↗
DOE OSTI2023

Can Zn isotopes in sediments record past eutrophication of freshwater lakes? A pilot study at Lake Baldegg (Switzerland)

In this study, the speciation and isotopic composition of Zn were traced across the sediments of a freshwater lake that experienced one hundred years of strong eutrophication, in order to assess the potential of sedimentary Zn isotopes to record such an environmental disturbance. Here, the results indicate that the sedimentary Zn isotope signal varied with the change from pre-eutrophic to eutrophic conditions in the investigated lake. The average δ 66 Zn JMC value of the dominantly allochthonous lithogenic sediments deposited during the pre-eutrophic period was +0.27‰ ±0.05‰ (i.e. similar to the δ 66 Zn JMC value of +0.28‰ ±0.05‰ proposed for Bulk Silicate Earth), while enhanced autochthonous biochemical sedimentation during the eutrophic period resulted in significantly lower δ 66 Zn JMC values down to +0.04‰ ±0.06‰. Synchrotron-based X-ray absorption spectroscopy data revealed a concomitant change in Zn speciation from a dominant fraction of Zn in clay minerals during the pre-eutrophic period to a major fraction of Zn in ZnS during the eutrophic period. A linear regression relating the sedimentary Zn isotope signal to the fraction of Zn in ZnS indicated δ 66 Zn JMC values of +0.27‰ ±0.06‰ and 0.00‰ ±0.08‰ for Zn in clay minerals and in ZnS, respectively. The enrichment of light Zn in ZnS in the eutrophic sediments is tentatively attributed to enhanced biological uptake of light Zn in the water column, which resulted in an enhanced flux of organic-bound Zn towards the sediments and further transformation of organic Zn into ZnS upon biomass mineralization during early diagenesis. This hypothesis is in agreement with the fractionation towards lighter Zn reported for both biological uptake of Zn and ZnS precipitation. The results of this study emphasize the potential of sedimentary Zn isotopes to register past eutrophic periods in freshwater lakes, and thus to serve as a probe of paleo-environmental conditions and/or past land use at the catchment scale.

58 GEOSCIENCES↗
DOE OSTI2026

Ab initio thermodynamics of Ni and Co incorporation in Mg hydroxide, carbonate, and hydroxycarbonate minerals

Ni and Co are critical elements needed for modern technologies, and a better understanding of the ability of Mg-based minerals to incorporate these elements would benefit strategy development for Ni and Co recovery from mafic and ultramafic deposits. Here, in this work, we performed density functional theory (DFT) calculations of Ni and Co incorporation in six potential products of the carbonation of mafic and ultramafic silicates: brucite (Mg(OH) 2 ), magnesite (MgCO 3 ), nesquehonite (MgCO 3 ⸱3H 2 O), lansfordite (MgCO 3 ⸱5H 2 O), artinite (Mg 2 CO 3 (OH) 2 ⸱3H 2 O), and hydromagnesite (Mg 5 (CO 3 ) 4 (OH) 2 ⸱4H 2 O). The DFT results were used in an ab initio thermodynamics framework to explore the pH 2 O–pCO 2 conditions at which the Mg-based minerals were predicted to be thermodynamically stable and to quantify the Gibbs free energy of Ni and Co substitution at Mg sites. Among the six Mg-based minerals, brucite and magnesite were predicted to have the lowest Ni and Co substitution free energy. An analysis of the effect of temperature indicated that, at low temperature (<100 K), brucite more readily accommodated Ni and Co, while, at higher temperature (>335 K), magnesite more favorably incorporated Ni and Co. Between 100 K and 335 K, Ni was predicted to preferentially substitute for Mg in brucite and Co for Mg in magnesite, thus leading to a driving force for separating Ni and Co in conditions where brucite and magnesite both form. Insights gained in this work could therefore help select experimental conditions that either promote or inhibit incorporation of these critical elements into Mg-based mineral phases.

Critical elements↗
DOE OSTI2026

Optimizing a chemical cleaning protocol to determine the nickel isotopic composition of ancient seawater from carbonates

Reconstructing the ancient marine cycle of Ni, a trace metal in the oceans essential to enzymes regulating the C, N, and O cycles, would inform how Ni bioavailability shaped early life. The Ni isotopic composition of seawater (δ 60 Ni SW ) through time could provide insight, but this approach requires sedimentary archives that faithfully record δ 60 Ni SW . Carbonates are an often-used record of seawater chemistry, but contaminants could bias the measured δ 60 Ni of bulk sediment. To isolate the true carbonate-bound δ 60 Ni signal, we optimized a chemical cleaning protocol designed to minimize non‑carbonate Ni contributions and maximize carbonate recovery. We analyzed ODP Site 1007 sediments and evaluated oxidative and reductive pre-cleaning steps and carbonate dissolution protocols. Our results show that only reductive cleaning significantly altered the subsequent carbonate leachate composition, lowering Ni/Ca ratios by up to 60% and δ 60 Ni values by as much as 0.4 ‰. In contrast, δ 60 Ni values were largely insensitive to premature carbonate dissolution during pre-cleaning or to partial leaching of silicates during carbonate dissolution, even at higher acid molarities or longer reaction times. We recommend an evidence-based protocol that removes hydro-soluble salts and clays, applies reductive cleaning and oxidative cleaning for certain sample compositions, and dissolves carbonate using 0.5 M acetic acid, adjusted to pH 5. Using these results, we infer a ∼ 0.9 ‰ Ni isotopic fractionation between chemically cleaned deep-water carbonates (+0.4 ± 0.1 ‰) and deep seawater. This method development is a key step toward accurately reconstructing ancient marine Ni cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Phyllosilicate mineral dissolution upon alkaline treatment under aerobic and anaerobic conditions

The dissolution of phyllosilicate minerals exposed to high-pH environments has been studied to determine the influence of alkaline treatments and variable redox conditions on clay dissolution and the potential formation of new phases via incongruent dissolution phenomena. The present study focused on the dissolution of phyllosilicate minerals (illite, muscovite, and montmorillonite) under anaerobic and aerobic conditions using comparative solutions (sodium hydroxide and ammonium hydroxide) at similar ionic strength in the presence and absence of oxygen. Our batch data show that there is a rapid decrease in aluminum dissolution (< 240 hrs) and slow increase in silica over time (up to 1440 hrs). This trend was particularly evident for montmorillonite which shows the greatest dissolution for ammonium hydroxide, likely due to intercalation of the polyatomic cation ammonium into the mineral’s expandable layers. When comparing alkaline treatments, the strong base, sodium hydroxide, dissolved more of the mica minerals, illite and muscovite, likely due to ion-pairing between the silicate tetrahedra [SiO4]n- and Na+ cations in solution. In addition, redox conditions affect the systems similarly with treatment, although the sodium hydroxide treatment results in greater variability in solution redox conditions. For all investigated phyllosilicates, the calculated aqueous aluminum and silicon ratios over time are significantly different from the minerals’ stoichiometric ratios. As a result, we conclude that incongruent dissolution occurred and suggest formation of secondary precipitates. Understanding the potential for clay mineral alterations from interaction with alkaline solutions has implications for in situ remediation, mining operations, and waste interactions with the subsurface. This research shows that incongruent dissolution is likely and will lead to secondary precipitation which may have long term physical and chemical impacts in the subsurface.

mineral dissolution, phyllosilicate, alkaline, amm↗
DOE OSTI2022

Micro- to nano-scale areal heterogeneity in pore structure and mineral compositions of a sub-decimeter-sized Eagle Ford Shale

Mineral and organic matter compositions & pore structures of fine-grained shale influence reservoir properties. To improve the understanding of spatial heterogeneity in core-sized samples, methods of microscale X-ray fluorescence (μXRF) mapping, (ultra-) small-angle x-ray scattering [(U)SAXS] and wide-angle X-ray scattering (WAXS) have been used to determine elemental, pore-structure variations at scales up to ~10 cm on two samples prepared at circular and rectangular orientations from a piece of Eagle Ford Shale outcrop in South Texas, USA. In addition, thin section petrography and field emission-scanning electron microscopy observations, X-ray diffraction (XRD), total organic carbon, and pyrolysis were utilized to investigate the potential spatial heterogeneity of pore types, mineral and organic matter compositions for cm-sized samples at both orientations. Overall, the siliceous-carbonate mineral contents in these two samples (8 cm×8 cm×0.08 cm and 5 cm × 8 cm × 0.08 cm, in terms of width×length×thickness) of carbonate-rich Eagle Ford Shale vary between laminations at mm scales. For the circular sample, porosity and specific surface area (SSA) variations range from 0.82 to 3.04% and 1.51 to 14.1 m 2 /g, respectively. For the rectangular sample, values for porosity and SSA vary from 0.93 to 2.50% and 3.95 to 10.8 m 2 /g. By analyzing six selected sub-samples on each of two samples with (U)SAXS and XRD techniques, nm-sized pores are mainly interparticle ones in the higher calcite regions, where the porosity is also relatively lower, while the lower calcite regions consist of both interparticle and intraparticle pore types with higher porosity. Lastly, the μXRF and (U)SAXS mappings are combined to generate porosity distribution maps to provide more insights about sample heterogeneity related to the laminations and fractures at our observational scales.

58 GEOSCIENCES↗
DOE OSTI2019

Thermally-Induced morphological evolution of spherical silica nanoparticles using in-operando X-ray scattering measurements

The assembly and morphology of pores determine thermodynamic, flow and reactive properties of confined fluids. Yet, there is a limited understanding of how pore architectures dynamically develop in engineered and natural materials. To develop a calibrated understanding of fluid properties in confinement, the synthesis of architected materials has been proposed. The design of geo-architected materials has to be informed by the dynamic evolution of the morphology in response to thermal or chemical events. Here, we probe thermally induced morphological evolution of spherical silica nanoparticles 220 ± 30 nm in diameter using in-operando Ultra-Small and Small Angle X-Ray Scattering measurements. The calcination experiments demonstrated that at temperatures up to 600 °C the pore radii remained in the range of 2.15 nm–2.35 nm and the particle diameters in the range of 220 ± 30 nm. Sintering these calcined silica nanoparticles to temperatures up to 1050 °C reduced the pore size from 2.2 ± 0.1 nm to ~1.8–0.2 nm. These changes corresponded to the formation of siloxane (Si-O-Si) bridges resulting from dehydroxylation. The characteristic pore radius of sintered particles was also confirmed by N 2 adsorption measurements. These studies represent the use of non-invasive dynamic characterization methods such as X-ray scattering to elucidate thermally induced morphological evolution in architected siliceous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Multi-scale observations of structure and chemical composition changes of portland cement systems during hydration

There is little agreement about the mechanisms and few direct observations of the transition of cement paste from a slurry to a solid. This paper uses four different imaging techniques at multiple length scales (from 15.6 nm to 1 μm) to follow the three-dimensional microstructural evolution of portland cement, and monoclinic tricalcium silicate (mC 3 S) paste over the first 16 h of hydration. Measurements of over 60,000 particles captured every 10 min were made at the micron scale. Nanoscale examinations of the structure and chemical composition are used to support this work. The results show that hydration products with an average Ca/Si > 3 form on and near the surface of the hydrating particles prior to the acceleration period that appears to control the reaction rate. These hydration products appear to change in chemical composition as more rapid dissolution of C 3 S and formation of hydration products occur during the acceleration period. The findings are used to provide insights into the origin of the induction and acceleration periods during hydration.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Autogenous healing of Engineered Cementitious Composites (ECC) based on MgO-fly ash binary system activated by carbonation curing

Developing self-healing of concrete cracks represents a critical approach for extending material longevity. If demonstrated on concretes with CO 2 stored through carbonation curing, self-healing can further mitigate infrastructure lifecycle emissions. In this study, the self-healing process is investigated on novel Engineered Cementitious Composites (ECC) based on binary blends of reactive MgO cement and siliceous fly ash activated by carbonation. The self-healing was observed under cyclic wetting and drying exposures and was characterized by measurements of resonance frequency, optical microscopy and X-ray computed microtomography (XCT). Thermogravimetric analysis, X-ray powder diffraction and scanning electron microscopy were employed to assist in identifying healing products and mechanisms. It was found that micro-cracks could be autogenously filled in 7 wet-dry cycles, as evidenced by over 95% recovery of resonance frequency and healed crack appearance under optical microscopic observation. Nevertheless, the composite mechanical performance, particularly tensile strength and ductility, did not fully recover with respect to the uncracked specimens. The inadequate post-healing mechanical properties were consistent with XCT observations that indicated low material densities in the cracked area. Based on the chemical and microstructural characterizations, it was determined that nesquehonite crystallites were responsible for the crack filling. Although the nesquehonite filled cracks will be less permeable to invasion of reactive fluids, novel strategies are needed to establish more robust healing capability to completely restore the crack bridging and composite tensile performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Natural carbonation of portland cement with synthetic zeolite Y as a supplementary cementitious material

Risks associated with carbonation are a key limitation to greater replacement levels of ordinary portland cement (OPC) by supplementary cementitious materials (SCMs). The addition of pozzolanic SCMs in OPC alters the hydrate assemblage by forming phases like calcium-(alumina)-silicate-hydrate (C-(A)-S-H). The objective of the present study was to elucidate how such changes in hydrate assemblage influence the chemical mechanisms of carbonation in a realistic OPC system. Here, in this paper, we show that synthetic zeolite Y (faujasite) is a highly reactive pozzolan in OPC that reduces the calcium content of hydration products via prompt consumption of calcium hydroxide from the evolving phase assemblage prior to CO 2 exposure. Suppression of portlandite at moderate to high zeolite Y content led to a more damaging mechanism of carbonation by disrupting the formation of a passivating carbonate layer. Without this layer, carbonation depth and CO 2 uptake are increased. Binders containing 12–18% zeolite Y by volume consumed all the calcium hydroxide from OPC during hydration and reduced the Ca/(Si+Al) ratio of the amorphous products to near 0.67. In these cases, higher carbonation depths were observed after exposure to ambient air with decalcification of C-(A)-S-H as the main source of CO 2 buffering. Binders with either 0% or 4% zeolite Y contained calcium hydroxide in the hydrated microstructure, had higher Ca/(Si+Al) ratios, and formed a calcite-rich passivation layer that halted deep carbonation. Although the carbonated layer in the samples with 12% and 18% zeolite Y contained 70% and 76% less calcite than the OPC respectively, their higher carbonation depths resulted in total CO 2 uptakes that were 12x greater than the OPC sample. Passivation layer formation in samples with calcium hydroxide explains this finding and was further supported by thermodynamic modeling. High Si/Al zeolite additives to OPC should be balanced with the calcium content for optimal carbonation resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Elastic and magnetic properties of Fe 3 P up to core pressures: Phosphorus in the Earth's core

Phosphorus (P) is considered a possible light element alloying with iron (Fe) in the Earth's core due to its siderophile nature and the ubiquity of P-bearing iron alloys in iron meteorites. The sequestration of P by liquid metals during the core formation possibly results in the relatively low concentration of P in the bulk silicate Earth. Here, we performed single-crystal and powder X-ray diffraction, synchrotron Mossbauer spectroscopy and nuclear resonant inelastic X-ray scattering measurements in diamond anvil cells to investigate the elastic and magnetic properties of Fe 3 P under high pressures. Our X-ray diffraction results suggest that there is no structural phase transition up to 111 GPa. However, a volume collapse was observed at 21.5 GPa in Fe 3 P, ascribed to a magnetic transition as evidenced by synchrotron Mhssbauer spectroscopy results. Fitting the volume-pressure data by the Birch-Murnaghan equation of state gives bulk modulus $K_{T0}$ = 162.4(7) GPa, its first pressure derivative $K'_{T0}$ = 4.0 (fixed) and zeropressure volume $V_0$ = 370.38(6) Å 3 for the magnetic phase and $K_{T0}$ = 220(7) GPa, $K'_{T0}$ = 4.0 (fixed) and $V_0$ = 357(1) Å 3 for the non-magnetic phase. Sound velocities of Fe 3 P were determined up to 152 GPa by nuclear resonant inelastic X-ray scattering, demonstrating that Fe 3 P bears a low shear velocity and high Poisson's ratio at core pressures compared to Fe and Fe 3 S. When forming a solid solution Fe 3 (S,P) with Fe 3 S at core pressures, Fe 3 P may favorably influence the elastic properties of Fe 3 (S,P) to match the seismic observations of the inner core.

58 GEOSCIENCES↗
DOE OSTI2023

Noble gas insights into early impact delivery and volcanic outgassing to Earth's atmosphere: A limited role for the continental crust

Earth's atmosphere, crust and mantle have evolved together through continuous geochemical exchange throughout Earth's history. Constraints on the transport of volatile elements and compounds between these reservoirs are crucial for understanding how Earth could have stayed habitable for extended periods of time. In this work, we present a new forward model of He, Ne and Ar in the mantle, crust and atmosphere. We explore concentrations of noble gases at the end of accretion, bulk silicate Earth K/U ratios, crustal growth scenarios, and upper mantle processing rates throughout Earth's history. We search for parameter combinations that simultaneously satisfy observational constraints on present-day mantle 4 He/ 3 He and 40 Ar/ 36 Ar (sensitive to mantle outgassing and continental crust growth, which depletes the mantle of U, Th and K), atmospheric 20 Ne/ 22 Ne (which tracks the mix of outgassed vs. delivered Ne in the atmosphere), and atmospheric 40 Ar/ 36 Ar in the past and today (sensitive to volatile delivery, mantle outgassing and crustal growth). Leveraging this intertwined set of noble gas abundances and isotopic compositions yields new constraints on initial noble gas abundances in the mantle and on the proportions of atmospheric volatiles originating from delivery by impact degassing, mantle outgassing, and degassing of the continental crust. We find that atmospheric Ar isotopic evolution is primarily sensitive to the mantle processing rate history; the atmospheric Ar isotopic record should therefore not be used to reconstruct continental crust growth, but instead provides valuable insights into mantle processing rates. Our model predicts a measurably low 20 Ne/ 22 Ne ratio of ~9.7 in Archean atmospheric samples. Most of atmospheric primordial 36 Ar was directly delivered by chondritic bodies and not transferred to the atmosphere during an intense early episode of mantle outgassing. Nitrogen delivered by impact degassing could account for the present-day atmospheric nitrogen inventory.

58 GEOSCIENCES↗
DOE OSTI2024

Enabling thermal energy storage in structural cementitious composites with a novel phase change material microcapsule featuring an inorganic shell and a bio-inspired silica coating

Phase change material (PCM) microcapsules offer a promising approach for integrating PCM into building materials for efficient thermal energy storage. Here, this study presents the development of a novel PCM microcapsule specifically designed for incorporation into cementitious materials. The microcapsule consists of a low-cost PCM core derived from vegetable oil by-products and a durable inorganic shell made from cenosphere, a hollow fly ash generated from coal burning power plants. A novel process is developed to apply a silica coating to these cenosphere-based PCM microcapsules (CPCM), resulting in bioinspired-silica-coated CPCM microcapsules (BCPCM). This coating process draws inspiration from marine microorganism-based silica production and utilizes low-cost sodium silicate as a precursor, enabling eco-friendly and cost-effective manufacturing at ambient temperature and mild pH conditions. The morphology, chemical stability, and thermal properties of the BCPCM along with its thermo-mechanical performance in cementitious composites were comprehensively analyzed. Experimental results demonstrate successful silica deposition on BCPCM, leading to enhanced latent heat properties of the produced BCPCM. With the silica coating, BCPCM exhibits a 50 °C delay in thermal decomposition compared to CPCM, enhancing fire resistance and preventing premature PCM leakage of the microcapsule. The bioinspired silica coating effectively restores over 10% of the strength loss for each percent increase in CPCM incorporated into the mortar. The thermal performance experiments reveal that increasing the BCPCM content reduces temperature peaks and rates of temperature increase, indicating an improved capacity for thermal energy storage. This new PCM microcapsule provides a cost-effective solution to integrate thermal energy storage to cementitious material, as evidenced that over 30% of aggregates (in volume) can be replaced by the microcapsule without a drastic loss of strength.

25 ENERGY STORAGE↗
DOE OSTI2025

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗
DOE OSTI2022

Multimodal study of the impact of stimulation pH on shale pore structure, with an emphasis on organics behavior in alkaline environments

The tight nature of shale formations calls for hydraulic fracturing techniques able of altering the pore architecture to facilitate the production of hydrocarbon resources. The composition, pH, salinity, density and chemistry of Hydraulic Fracturing Fluids (HFF) vary substantially depending on reservoir characteristics. pH is among the most important stimulation fluid properties, ranging from very acidic, for carbonate reservoirs, to basic, in the case of clay-rich formations. pH regulates what geochemical reactions take place between the stimulation fluid and shale, as well as pore architecture alteration. The dissolution of carbonates and pyrite, and the precipitation of common minerals such as barite, gypsum and iron oxides in acidic environments have been extensively documented. In contrast, alkali stimulation environments and the role of organic components have received less attention. This research provides insight into the role of both minerals and organic components during alkaline stimulation, and the resulting pore architecture alterations. Here, a set of reactive experiments are performed using three different shales, with varying organic matter (OM) content, at different pH (3, 6, 8, 10, 12). The analysis of pore architecture alteration induced by the reaction was performed via nitrogen (N2) gas adsorption and Time-Domain Nuclear Magnetic Resonance (TD-NMR). Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES) was used to measure the composition of the stimulation fluid post-reaction. The system with a larger impact on the pore architecture (pH 12) underwent a more extensive analysis through the application of Focused Ion Beam Scanning Electron Microscopy (FIB-SEM) and x-ray Diffraction (XRD). Results show that mineral dissolution contributed to the creation of secondary porosity, mainly through dissolution of clays and silicates. We show that the abundance and distribution of organic matter both play a significant role in changes in pore architecture. Most samples showed an increase in inter-organic porosity, likely due to the organic acids within kerogen reacting with the stimulation fluid. Samples with a larger amount and more widespread distribution of organic matter show the most significant alterations. Finally, we also highlight the dissolution process of iron-rich minerals, including framboidal pyrite, as another important source of secondary porosity.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2019

Experimental determination of Zn isotope fractionation during evaporative loss at extreme temperatures

We report that zinc isotopes fractionate during evaporation, and thus can potentially be used to calculate the proportion of volatile elemental loss from objects such as tektites, nuclear fallout melt glasses formed from silicate soils, and rocks from the Moon. The utility of the Zn isotope system in constraining the magnitude of volatile loss depends on accurate knowledge of its fractionation behavior during evaporation, i.e., the Zn isotope fractionation factor. In this work, we present new results of Zn isotope analyses of experimentally heated soil samples, together with analyses of environmentally derived fallout melt glasses, and australite tektites, to better constrain how and to what extent Zn isotopes fractionate during thermally-driven evaporation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Constraining the behavior of gallium isotopes during evaporation at extreme temperatures

Renewed interest in gallium isotope systematics has stemmed from the fact that Ga is moderately volatile and is hypothesized to undergo kinetic fractionation during evaporation. In this work, we present the first Ga isotope data from terrestrial volatile depleted samples including a suite of experimentally heated rhyolitic soils, fallout melt glass, and splash-form tektites from the Australasian strewn field (hereafter termed australite tektites). The Ga in these samples is isotopically heavy compared to Ga in terrestrial basalts and estimates for the composition of the bulk silicate Earth (BSE). For each sample suite the isotopic fractionation of Ga scales with the degree of Ga depletion, consistent with isotopic fractionation caused by evaporation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

On the dissolution of a borosilicate glass with the use of isotopic tracing – Insights into the mechanism for the long-term dissolution rate

An understanding of the mechanisms responsible for controlling the long-term corrosion rate of nuclear waste glass is paramount if reliable glass dissolution models are to be used to calculate the controlled release of radionuclides from nuclear waste glass under geologic disposal conditions. Additionally, understanding silicate glass dissolution is also important for natural glasses to understand the role from the dissolution of these glasses has on the composition of natural aquatic systems. Two general mechanisms appear to be responsible for the elemental release from glass to the surrounding biosphere - ion exchange (release principally of alkalis) and matrix dissolution (release of the structural components of the glass). Key unknowns related to these mechanisms are the impact of surface layers on the altered glass and how these layers participate in corrosion. To better understand the impact of these layers on glass corrosion, we made two glasses of the same elemental composition, but with selected elements enriched in specific isotopes, e.g. more 10 B than 11 B. We reacted these glasses for 1 y then the solutions from each were exchanged and the chemistry of the solutions and the solids were followed for another 2 y and in some cases 3 y. This allowed us to follow changes in the glasses with respect to these elements and how these elements were transported through the alteration layers with time and, for at least one element, into the glass. Results from these experiments demonstrate that the release behavior of different elements is strongly dependent on their structural role in the glass (e.g. network formers and modifiers), but, more importantly, the role of water transport and subsequent ion exchange has in the long-term dissolution of the glass studied here. In this article, we highlight the behavior of four elements: lithium, sodium, silicon, and boron. Lithium and sodium, network modifying elements, have similar chemistries. The behavior of Li could be tracked in more detail by following both 6 Li and 7 Li; Li penetrates through the gel layer in both directions without hinderance and into and released from the glass deeper than sodium. Silicon, a network forming element, reacts with the silica-rich alteration layer. Boron, a network forming element, does not accumulate in the gel or the pristine glass and has a very sharp elemental profile between the pristine glass and alteration layer. Boron, lithium, and sodium elemental profiles suggest that there is little if any transport control within the alteration layer. The correlation between the Li and Na profiles and that of a water species suggest that the limiting release is a steady state between the diffusion of a water species and matrix dissolution that results in a low release rate for alkali and this provides a steady driving force for the long-term dissolution of glass.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗