Search NASA⌕ Search

SEARCH · Search NASA

Results for “solar materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Triple-halide wide–band gap perovskites with suppressed phase segregation for efficient tandems

Wide–band gap metal halide perovskites are promising semiconductors to pair with silicon in tandem solar cells to pursue the goal of achieving power conversion efficiency (PCE) greater than 30% at low cost. However, wide–band gap perovskite solar cells have been fundamentally limited by photoinduced phase segregation and low open-circuit voltage. Here, we report efficient 1.67–electron volt wide–band gap perovskite top cells using triple-halide alloys (chlorine, bromine, iodine) to tailor the band gap and stabilize the semiconductor under illumination. We show a factor of 2 increase in photocarrier lifetime and charge-carrier mobility that resulted from enhancing the solubility of chlorine by replacing some of the iodine with bromine to shrink the lattice parameter. We observed a suppression of light-induced phase segregation in films even at 100-sun illumination intensity and less than 4% degradation in semitransparent top cells after 1000 hours of maximum power point (MPP) operation at 60°C. By integrating these top cells with silicon bottom cells, we achieved a PCE of 27% in two-terminal monolithic tandems with an area of 1 square centimeter.

14 SOLAR ENERGY↗
DOE OSTI2020

Correlated Electrical and Chemical Nanoscale Properties in Potassium-Passivated, Triple-Cation Perovskite Solar Cells

Perovskite semiconductors are an exciting class of materials due to their promising performance outputs in photovoltaic devices. To boost their efficiency further, researchers introduce additives during sample synthesis, such as KI. However, it is not well understood how KI changes the material and, often, leaves precipitants. To fully resolve the role of KI, multiple microscopy techniques are applied and the electrical and chemical behavior of a Reference (untreated) and a KI-treated perovskite are compared. Upon correlation between electrical and chemical nanoimaging techniques, it is discovered that these local properties are linked to the macroscopic voltage enhancement of the KI-treated perovskite. The heterogeneity revealed in both the local electrical and chemical responses indicates that the additive partially migrates to the surface, yet surprisingly does not deteriorate the performance locally, rather, the voltage response homogeneously increases. The research presented within provides a diagnostic methodology, which connects the nanoscale electrical and chemical properties of materials, relevant to other perovskites, including multication and Pb-free alternatives.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of an operando characterization stage for multi-modal synchrotron x-ray experiments

It is widely accepted that micro- and nanoscale inhomogeneities govern the performance of many thin-film solar cell absorbers. These inhomogeneities yield material properties (e.g., composition, structure, and charge collection) that are challenging to correlate across length scales and measurement modalities. The challenge is compounded if a correlation is sought during device operation or in conditions that mimic aging under particular stressors (e.g., heat and electrical bias). Correlative approaches, particularly those based on synchrotron x-ray sources, are powerful since they can access several material properties in different modes (e.g., fluorescence, diffraction, and absorption) with minimal sample preparation. Small-scale laboratory x-ray instruments have begun to offer multi-modality but are typically limited by low x-ray photon flux, low spatial resolution, or specific sample sizes. To overcome these limitations, a characterization stage was developed to enable multi-scale, multi-modal operando measurements of industrially relevant photovoltaic devices. The stage offers compatibility across synchrotron x-ray facilities, enabling correlation between nanoscale x-ray fluorescence microscopy, microscale x-ray diffraction microscopy, and x-ray beam induced current microscopy, among others. Furthermore, the stage can accommodate device sizes up to 25 × 25 mm 2 , offering access to multiple regions of interest and increasing the statistical significance of correlated properties. The stage materials can sustain humid and non-oxidizing atmospheres, and temperature ranges encountered by photovoltaic devices in operational environments (e.g., from 25 to 100 °C). As a case study, we discuss the functionality of the stage by studying Se-alloyed CdTe photovoltaic devices aged in the stage between 25 and 100 °C.

14 SOLAR ENERGY↗
DOE OSTI2021

Device Performance of Emerging Photovoltaic Materials (Version 2)

Following the 1st release of the "Emerging photovoltaic (PV) reports", the best achievements in the performance of emerging photovoltaic devices in diverse emerging photovoltaic research subjects are summarized, as reported in peer-reviewed articles in academic journals since August 2020. Updated graphs, tables, and analyses are provided with several performance parameters, e.g., power conversion efficiency, open-circuit voltage, short-circuit current density, fill factor, light utilization efficiency, and stability test energy yield. These parameters are presented as a function of the photovoltaic bandgap energy and the average visible transmittance for each technology and application and are put into perspective using, e.g., the detailed balance efficiency limit. The 2nd installment of the "Emerging PV reports" extends the scope toward tandem solar cells and presents the current state-of-the-art in tandem solar cell performance for various material combinations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Methods of forming interdigitated back contact solar cells

Methods for forming interdigitated back contact solar cells from III-V materials are provided. According to an aspect of the invention, a method includes depositing a patterned Zn layer to cover first areas of an n-type emitter region, wherein the emitter region comprises a III-V material, and forming a passivated back contact region by counter-doping the first areas of the emitter region by diffusing Zn from the patterned Zn layer into the first areas of the emitter region, such that the first areas of the emitter region become p-type.

14 SOLAR ENERGY↗
DOE OSTI2019

The great isotopic dichotomy of the early Solar System

The isotopic composition of meteorites and terrestrial planets holds important clues about the earliest history of the Solar System and the processes of planet formation. Recent work has shown that meteorites exhibit a fundamental isotopic dichotomy between non-carbonaceous (NC) and carbonaceous (CC) groups, which most likely represent material from the inner and outer Solar System, respectively. Here we review the isotopic evidence for this NC–CC dichotomy, discuss its origin and highlight the far-reaching implications for the dynamics of the solar protoplanetary disk. The NC–CC dichotomy combined with the chronology of meteorite parent-body accretion mandate an early and prolonged spatial separation of inner (NC) and outer (CC) disk reservoirs, lasting between ~1 and ~4 Myr after Solar System formation. This is most easily reconciled with the early and rapid growth of Jupiter’s core, inhibiting substantial exchange of material from inside and outside its orbit. Here, the growth and migration of Jupiter also led to the later implantation of CC bodies into the inner Solar System and, therefore, can explain the co-occurrence of NC and CC bodies in the asteroid belt, and the delivery of volatile and water-rich CC bodies to the terrestrial planets.

58 GEOSCIENCES↗
DOE OSTI2023

Renewable Energy Materials Properties Database: Summary

Renewable energy is providing a growing share of electricity generation in the United States, with generation from utility scale wind and solar increasing by 12% and 29%, respectively, in 2020 (EIA 2021). Installation of new renewable energy facilities requires material inputs that range from common construction materials to specialized, high-performance materials that may have limited availability. This report summarizes the Department of Energy (DOE) Wind Energy Technologies Office (WETO) and DOE Solar Energy Technologies Office (SETO) database of materials used in domestic wind and solar installations. The Energy Act of 2020 directs WETO and SETO to deliver a "comprehensive physical property database of materials for use in [wind and solar] energy technologies, which shall identify the type, quantity, country of origin, source, significant uses, projected availability, and physical properties of materials used in [wind and solar] energy technologies" by no later than September 1, 2022. This report is the summary and directions for use of the Renewable Energy Materials Property Database (REMPD), in response to that direction. The related full text of the Energy Act of 2020 is provided in Appendix A. The focus of the REMPD and this accompanying report is on quantifying the raw and processed materials used in renewable energy technologies. The database contains information on the amount of each material that goes into wind and solar power plants, descriptions of the relevant material properties, and the primary countries of origin for each material. Some materials go through several stages of processing and/or are incorporated into subcomponents that make up the completed energy generation facilities. This report does not analyze supply chains for the production of renewable energy plant components. The Department of Energy has carried out related analysis in response to Executive Order 14017, which directed production of "America's Supply Chains" reports for Wind and Solar. The supply chain reports can be found at https://www.energy.gov/sites/default/files/2022-02/Wind%20Supply%20Chain%20Report%20-%20Final%202.25.22.pdf (Wind) and https://www.energy.gov/sites/default/files/2022-02/Solar%20Energy%20Supply%20Chain%20Report%20-%20Final.pdf (Solar). Additional reports in this series that are relevant to wind, solar and hybrid plants include: Energy Storage at https://www.energy.gov/sites/default/files/2022-02/Energy%20Storage%20Supply%20Chain%20Report%20-%20final.pdf and Neodymium Magnets at https://www.energy.gov/sites/default/files/2022-02/Neodymium%20Magnets%20Supply%20Chain%20Report%20-%20Final.pdf.

14 SOLAR ENERGY↗
DOE OSTI2021

Design of High-Performance Lead-Free Quaternary Antiperovskites for Photovoltaics via Ion Type Inversion and Anion Ordering

The emergence of halide double perovskites significantly increases the compositional space for lead-free and air-stable photovoltaic absorbers compared to halide perovskites. Nevertheless, most halide double perovskites exhibit oversized band gaps (>1.9 eV) or dipole-forbidden optical transition, which are unfavorable for efficient single-junction solar cell applications. The current device performance of halide double perovskite is still inferior to that of lead-based halide perovskites, such as CH 3 NH 3 PbI 3 (MAPbI 3 ). Here, by ion type inversion and anion ordering on perovskite lattice sites, two new classes of pnictogen-based quaternary antiperovskites with the formula of X 6 B 2 AA' and X 6 BB'A 2 are designed. Phase stability and tunable band gaps in these quaternary antiperovskites are demonstrated based on first-principles calculations. Further photovoltaic-functionality-directed screening of these materials leads to the discovery of 5 stable compounds (Ca 6 N 2 AsSb, Ca 6 N 2 PSb, Sr 6 N 2 AsSb, Sr 6 N 2 PSb, and Ca 6 NPSb 2 ) with suitable direct band gaps, small carrier effective masses and low exciton binding energies, and dipole-allowed strong optical absorption, which are favorable properties for a photovoltaic absorber material. The calculated theoretical maximum solar cell efficiencies based on these five compounds are all larger than 29%, comparable to or even higher than that of the MAPbI 3 based solar cell. Finally, our work reveals the huge potential of quaternary antiperovskites in the optoelectronic field and provides a new strategy to design lead-free and air-stable perovskite-based photovoltaic absorber materials.

three-dimensional electronic transport↗
DOE OSTI2020

Disorder-Tunable ZnGeP2 for Epitaxial Top Cells on Si

There has been a longstanding search for top cell materials for Si-based tandems. ZnGeP 2 is one material that could fit this need. It is lattice matched to Si and has the potential for tuning its band gap at fixed lattice constant via cation ordering. In this study, we investigate the effects of growth and annealing conditions on the structure of ZnGeP 2 thin films. Films were deposited amorphous and then annealed ex-situ. Using low anneal temperatures or short anneal times, we were able to kinetically trap the disordered phase. We also found composition to play a role in the degree of ordering in our films. Our findings support the hypothesis that ZnGeP 2 could be implemented as a material with tunable properties at fixed lattice constant through cation ordering.

14 SOLAR ENERGY↗
DOE OSTI2023

Multi–Resonant Mie Resonator Arrays for Broadband Light Trapping in Ultrathin c–Si Solar Cells

Effective photon management is critical to realize high power conversion efficiencies for thin crystalline silicon (c–Si) solar cells. Standard few–100–µm–thick bulk cells achieve light trapping with macroscopic surface textures covered by thin, continuous antireflection coatings. Such sizeable textures are challenging to implement on ultrathin cells. Here, it is illustrated how nanoscale Mie–resonator–arrays with a bimodal size distribution support multiple resonances that can work in concert to achieve simultaneous antireflection and light–trapping across the broad solar spectrum. The effectiveness of these light–trapping antireflection coatings is experimentally demonstrated on a 2.8 µm–thick c–Si solar cell. The measured short–circuit current and corresponding power conversion efficiency are notably improved, achieving efficiencies as high as 11.2%. Measurements of the saturation current density on completed cells indicate that thermal oxides can effectively limit surface recombination. Finally, the presented design principles are applicable to a wide range of solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

CsI-Antisolvent Adduct Formation in All-Inorganic Metal Halide Perovskites

The excellent optoelectronic properties shown by hybrid organic/inorganic metal halide perovskites are all predicated on precisely controlling the exact nucleation and crystallization dynamics that occur during film formation. In general, high-performance thin films are obtained by a method commonly called solvent engineering (or antisolvent quench) processing. The solvent engineering method removes excess solvent, but importantly leaves behind solvent that forms chemical adducts with the lead-halide precursor salts. These adduct-based precursor phases control nucleation and the growth of the polycrystalline domains. There has not yet been a comprehensive study comparing the various antisolvents used in different perovskite compositions containing cesium. In addition, there have been no reports of solvent engineering for high efficiency in all-inorganic perovskites such as CsPbI 3 . In this work, inorganic perovskite composition CsPbI 3 is specifically targeted and unique adducts formed between CsI and precursor solvents and antisolvents are found that have not been observed for other A-site cation salts. These CsI adducts control nucleation more so than the PbI 2 -dimethyl sulfoxide (DMSO) adduct and demonstrate how the A-site plays a significant role in crystallization. The use of methyl acetate (MeOAc) in this solvent engineering approach dictates crystallization through the formation of a CsI-MeOAc adduct and results in solar cells with a power conversion efficiency of 14.4%.

14 SOLAR ENERGY↗
DOE OSTI2019

Optical and Structural Properties of High-Efficiency Epitaxial Cu(In,Ga)Se 2 Grown on GaAs

Photovoltaic devices based on Cu(In,Ga)Se 2 (CIGS) usually employ polycrystalline thin films as the absorber layer. This is because, to date, the highest conversion efficiencies have been attained with polycrystalline CIGS films. Recently, Nishinaga et al. presented an epitaxial CIGS thin-film solar cell grown on a GaAs (100) substrate with a conversion efficiency of 20.0%. In this contribution, we study the optical and structural properties of this high-efficiency epitaxial film, along with others with different compositions using cathodoluminescence spectrum imaging and transmission electron microscopy. A comparison of the high-efficiency epitaxial film and a traditional polycrystalline film with a similar global composition reveals significant differences in microstructure and uniformity of emission properties despite similar performance. The analysis of epitaxial films with a higher gallium concentration indicates that the emission characteristics and nature of extended defects in epitaxial CIGS films are strongly dependent on the gallium content. The results presented here provide evidence that, with further optimization, photovoltaic conversion efficiencies of epitaxial CIGS films could exceed those of polycrystalline CIGS.

14 SOLAR ENERGY↗
DOE OSTI2022

Microdroplet Electrospray Localized Laser Printing and Sintering of Nanoparticles for Passivating, Carrier-Selective Contacts (Final Technical Report)

In this project, the team used a nanoparticle electrospray laser deposition (NELD) process developed at the University of Central Florida (UCF) to address current limitations of passivating, carrier-selective contact technologies for crystalline silicon (c-Si) photovoltaic (PV) cells. The NELD process was used to print low bulk line resistivity Ag contacts directly onto transparent conductive oxides (TCOs), like indium tin oxide (ITO), for hydrogenated amorphous silicon (a-Si:H) based c-Si heterojunction (SHJ) cells without any subsequent contact firing step needed.

14 SOLAR ENERGY↗
DOE OSTI2026

PV Fleet Performance Data Initiative 2026 Update

We provide an update on the PV Fleet Performance Data Initiative at the 2026 PV Reliability Workshop. Our latest runs incorporate additional data sources and an integrated analysis pipeline run on our Kestrel HPC cluster. Initial degradation findings suggest that single-axis tracked PV systems exhibit higher performance loss rates than fixed-tilt systems, an increase of 0.5 %/yr, almost double. We discuss multiple methods for identifying stuck tracker rows, which are suspected to be a contributor to the enhanced degradation. Through satellite image detection and data-driven approaches we address the topic of identifying when stuck trackers are occuring and to what extent the problem exists. Preliminary results suggest that the increased performance loss detected for the tracked systems would be consistent with stuck tracker rows affecting on the order of 5% - 10% of the system.

14 SOLAR ENERGY↗
DOE OSTI2022

Innovative Method for Welding in Generation 3 CSP to Enable Reliable Manufacturing of Solar Receivers to withstand Daily Cycling at Temperatures Above 700°C (Final Technical Report)

Inconel® Alloy 740H® (alloy 740H) was the first age-hardenable nickel-based alloy approved by the ASME Boiler & Pressure Vessel Code for use in pressure-boundary applications. Over the past ~20 years the alloy has been optimized for weldability and high-temperature stability, approved for use in different applications. Development of a supply chain combined with the advantageous properties of the alloy (high-temperature creep strength, oxidation and corrosion resistance, etc.) have resulted in the alloy being applied to new high-temperature power cycle demonstration projects, and of particular interest are applications to concentrating solar power (CSP) to enable higher-efficiency Generation 3 CSP systems and the corresponding supercritical CO 2 (sCO 2 ) power cycle components (heat exchangers, piping, etc.). The high allowable stresses of alloy 740H also make it a desirable material for current Generation 2 CSP solar power receivers to improve cyclic capability and/or reduce receiver height. Recent experiences in demonstration projects utilizing alloy 740H identified cracking issues during welding and fabrication. In this project, a detailed study was done to confirm and clarify the Stress Relaxation Cracking (SRxC) mechanism, also known as stress relief cracking or strain-age cracking (SAC), during post-weld heat-treatment (PWHT). This involved detailed microscopy and advanced characterization to understand the root cause(s) of three failures obtained from industry. Based in-part on these findings, a targeted laboratory based SRxC test method was utilized to evaluate variables such as heat-to-heat variations, strain level, PWHT temperature, and starting material condition on three heats of alloy 740H. Industrial shop welding of cold-worked plates was also conducted. The research showed the following: SRxC was confirmed as the cracking mechanism for all field failures; Stress state (from residual stresses, constraint, deformation, and local stress concentrations) was playing a significant role in field failures and laboratory testing confirmed increasing susceptibility for all heats with increasing strain levels. High levels of microstructural strain were identified at crack initiation locations, in some cases leading to local recrystallization; Precipitate free zones (PFZs) at grain boundaries were found at relaxation cracks and crack initiation locations uniquely associated with SRxC in alloy 740H. Laboratory testing reproduced this microstructural feature which had only previously been reported in long-term creep testing of weldments. Advanced nano-scale characterization confirmed the presence of a moving boundary leading to coarsening of precipitates and PFZs where damage accumulated; The research suggested heat-to-heat variations due to local chemistry and processing may influence SRxC susceptibility, but more work is needed to fully clarify these effects. To disseminate the key learnings from this research to the scientific and engineering communities and alloy 740H end users, multiple technical publications and presentations were made, an industrial alloy 740H users meeting was held, and a new industry guideline specification document which can be directly implemented by end-users of alloy 740H was produced.

14 SOLAR ENERGY↗
DOE OSTI2023

Measurement and Reporting Guidelines for Solar Mirror Aging Tests Using Xenon Arc Lamp Exposure (XALE)

This technical report provides a guideline for accelerated aging tests on solar reflectors. Solar reflectors must have a high durability, with goal lifespans reaching 30 years. To test and develop state-of-the-art solar reflectors, relevant durability tests must be conducted. Existing guidelines for materials testing include isothermal testing, humidity testing, corrosion, etc., but many tests do not specify to include solar irradiance or address its relevance to solar reflector durability. The guideline focuses on test design and reporting guidelines for using Xenon Arc Lamp Exposure (XALE). The XALE environmental chambers can subject samples to a combination of relevant environmental factors including concentrated solar irradiance, heat, humidity, and weathering cycles. The guideline is meant to provide information on developing relevant test conditions, exposure times, reflectance characterization procedures, and data reporting.

14 SOLAR ENERGY↗