Search NASA⌕ Search

SEARCH · Search NASA

Results for “test effectiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Design, production, and testing of field effect transistors

Cryogenic MOSFETS (CRYOFETS), specifically designed for low temperature preamplifier application with infrared extrinsic detectors were produced and comparatively tested with p-channel MOSFETs under matched conditions. The CRYOFETs exhibit lower voltage thresholds, high source-follower gains at lower bias voltage, and lower dc offset source voltage. The noise of the CRYOFET is found to be 2 to 4 times greater than the MOSFET with a correspondingly lower figure of merit (which is established for source-follower amplifiers). The device power dissipation at a gain of 0.98 is some two orders of magnitude lower than for the MOSFET. Further, CRYOFETs are free of low temperature I vs V character hysteresis and balky conduction turn-on effects and operate effectively in the 2.4 to 20 K range. These devices have promise for use on long term duration sensor missions and for on-focal-plane signal processing at low temperatures.

Sclar, N.↗
NASA NTRS2004

Two-Dimensional Air-Flow Tests of the Effect of ITA Flowliner Slot Modification by Grinding/Polishing on Edge Tone Generation Potential

Hersh Walker Acoustics (HWA) has performed a series of wind tunnel tests to support crack-repair studies for ITA flowliner vent slots. The overall goal of these tests is to determine if slot shape details have a significant influence on the propensity of the flowliner to produce aero-acoustic oscillations that could increase unsteady stresses on the flowliner walls. The test series, conducted using a full-scale two-dimensional model of a six-slot segment of the 38 slot liner, was intended to investigate the effects of altering slot shape by grinding away cracked portions.

Sutliff, Daniel L.↗
NASA NTRS1975

Cost effective dynamic design and test requirements for Shuttle payloads

The results of a study examining current spacecraft dynamic design and test requirements for the cost effective design and development of Shuttle payloads are presented. Dynamic environments, payload configurations, design/test requirements, test levels, assembly level of testing, simulation methods, prototype role, load limiting, test facilities, and flight measurements are discussed as they relate to the development of a cost effective design and test philosophy for Shuttle Spacelab payloads. It is concluded that changes to current design/test practices will minimize long range payload costs. However, changes to current practices need be quantitatively evaluated before an orderly progression to more cost effective methods can be achieved without undue risk of mission failures. Of major importance is optimization of test levels and plans for payloads and payload subsystems which will result in minimum project costs.

Stahle, C. V.↗
NASA NTRS1988

Effects of initial delamination on CIc and GIth values from glass/epoxy double cantilever beam tests

The effect of insert thickness and method of precracking on mode I interlaminar fracture toughness, GIc, and delamination fatigue threshold, GIth, values were determined for a glass/epoxy double cantilever beam specimen. The results of the static tests showed that precracking in tension would cause fiber bridging and thus may yield unconservative values of GIc and GIth. Precracking in shear yields suitable values of GIc but overly conservative values of GIth. For the glass/epoxy composite used, an insert thickness of 0.5 mil was most suitable for determining GIc and GIth values, although an insert thickness up to 3 mil was acceptable. Inserts thicker than 3 mil were not acceptable for determining GIc and GIth values.

Martin, Roderick H.↗
NASA NTRSDate not supplied

A Psychoacoustic Test on the Effect of Masking on Annoyance to Urban Air Mobility Vehicle Noise

Urban Air Mobility (UAM) vehicles have a large range of designs and configurations that lead to new noise characteristics and potentially different perceptual responses when compared to traditional aircraft. In addition, UAM vehicles are expected to operate around and within densely populated regions where the presence of ambient background noise is often present. Strategically, this can be leveraged to inform vehicle design and operations to partially or completely mask UAM noise, allowing for mitigation of negative responses and an increased number of allowed operations. A psychoacoustic test was conducted to investigate how masking effects can influence the annoyance response to a low frequency harmonic tone complex (80-320 Hz). To do this, five test subjects compared their annoyance response to the low frequency tonal noise with a higher frequency broadband noise (10dB down bandwidth between 300-2000 Hz), with and without a masking noise present. Detection thresholds were also measured for both sounds to help fit a model to the data. Although the effect of masking on annoyance is complex, results indicate that for some individuals, masking leads to a lower annoyance than the sound level alone would predict.

Matthew Boucher↗
NASA NTRS2008

Random Test Run Length and Effectiveness

A poorly understood but important factor in many applications of random testing is the selection of a maximum length for test runs. Given a limited time for testing, it is seldom clear whether executing a small number of long runs or a large number of short runs maximizes utility. It is generally expected that longer runs are more likely to expose failures -- which is certainly true with respect to runs shorter than the shortest failing trace. However, longer runs produce longer failing traces, requiring more effort from humans in debugging or more resources for automated minimization. In testing with feedback, increasing ranges for parameters may also cause the probability of failure to decrease in longer runs. We show that the choice of test length dramatically impacts the effectiveness of random testing, and that the patterns observed in simple models and predicted by analysis are useful in understanding effects observed.

software testing↗
NASA NTRS1985

Studies of condensation effects on airfoil testing in a transonic cryogenic tunnel

In the context of an overall development of transonic, cryogenic wind tunnel technology, NASA has been investigating the onset of condensation effects in nitrogen gas. The temperature at which condensation occurs determines the minimum operating temperature (MOT) of cryogenic tunnels. The apparatus and airfoils are discussed, taking into account a description of the 0.3-m Transonic Cryogenic Tunnel (TCT), the drag rake, the airfoils, and the technique used for determining the onset of condensation effects. Attention is also given to the types of nucleation processes, the relative sensitivity of drag rake and surface pressure measurements, correlations between data and theory, the prediction of minimum operating temperatures for the 0.3-m TCT, and MOT's for different tunnels.

Hall, R. M.↗
NASA NTRS1988

A test for interfacial effects and stress transfer in ceramic matrix composites

The efforts to fabricate single embedded filament specimens of carbon and SiC fibers were unsuccessful largely due to the thermal stresses resulting from differences in thermal coefficient of expansion. Other factors appear to have been involved including embrittlement of the metal substrate by the H2 gas in the chemical vapor deposition flow stream and reaction layers formed between the silicon carbide and the metal substrate. The carbon fiber may have been attacked by the CVD reactant. It is concluded that these differential stresses are so large as to make the embedded fiber test impractical for the study of interphase effects and stress transfer in fiber ceramic matrix systems.

Bascom, Willard D.↗
NASA NTRS1986

Studies of condensation effects on airfoil testing in the Langley 0.3-meter transonic cryogenic tunnel

In the context of an overall development of transonic, cryogenic wnd tunnel technology, NASA has been investigating the onset of condensation effects in nitrogen gas. The temperature at which condensation occurs determines the minimum operating temperature (MOT) of cryogenic tunnels. The apparatus and airfoils are discussed, taking into account a description of the 0.3-m Transonic Cryogenic Tunnel (TCT), the drag rake, the airfoils, and the technique used for determining the onset of condensation effects. Attention is also given to the types of nucleation processes, the relative sensitivity of drag rake and surface pressure measurements, correlations between data and theory, the prediction of minimum operating temperatures for the 0.3-m TCT, and MOT's for different tunnels.

Hall, R. M.↗
NASA NTRS1936

Tank Tests of the Effect of Rivet Heads, etc., on the Water Performance of a Seaplane Float, Special Report

A 1/3.5 full-size model of the Mark V float of the Bureau of Aeronautics, Navy Department, was tested in the NACA tank both with smooth painted bottom surfaces and with roundhead rivets, plate laps, and keel plates fitted to simulate the actual bottom of a metal float. The augmentation in water resistance due to the added roughness was found to be from 10-12% at the hum speed and from 12-14% at high speeds. The effect of the roughness of the afterbody was found to be negligible except at high trims. The model data were extrapolated to full size by the usual method which assumes the forces to vary according to Froude's law, and in the case of the smooth model by a method of separation that takes into account the effect of scale on the frictional resistance. It was concluded that the effect of rivet heads on the takeoff performance of a relatively high-powered float seaplane is of little consequence but that it may be of greater importance in the case of more moderately powered flying boats.

Parkinson, J. B.↗
NASA NTRS1976

Spin tests of a low-wing monoplane to investigate scale effect in the model test range, May 1941

Concurrent tests were performed on a 1/16 and a 1/20 scale model (wing spans of 2.64 and 2.11 ft. respectively) of a modern low wing monoplane in the NACA 15 foot free-spinning wind tunnel. Results are presented in the form of charts that afford a direct comparison between the spins of the two models for a number of different conditions. Qualitatively, the same characteristic effects of control disposition, mass distribution, and dimensional modifications were indicated by both models. Quantitatively, the number of turns for recover and the steady spin parameters, with the exception of the inclination of the wing to the horizontal, were usually in good agreement.

Donlan, C. J.↗
NASA NTRS2020

Controlled Environmental Effects on Creep Test Data of Woven Fabric Webbings for Inflatable Space Modules

eveloping technologies for proposed lunar and Mars space exploration missions. Enhanced habitation sy g studied as potential habitats due to their inherent low mass and small launch volume. One goal of inflatable module research is quantification of the safe-life and end-of-life creep-strain spectrum. Full-scale pressurized inflatable modules are large, costly, and difficult to experimentally study. Therefore, material subcomponents are often studied as an alternative. An experimental thermally controlled long-term creep study of VectranTM webbings for application to inflatable modules is presented. Vectran fibers have high strength and low creep properties. High strength webbing materials are desirable for the load bearing restraint layer of inflatable modules because they are strong, flexible, and lightweight. Characterization of the creep behavior, safe-life, and end-of- life of webbing specimens will help quantify comparable life properties for inflatable modules. Several experimental multiple-year creep studies of webbing specimens in uncontrolled thermal environments have been conducted at NASA Langley Research Center. Experimental data obtained exhibits the classic creep-strain curve due to load, coupled with unique sinusoidal variation due to variation in temperature and humidity over daily and annual time periods. Results also have indicated that specimens fail within a year if the applied load is greater than 50 percent of the rated load. The primary goal of this study is to eliminate thermal effects from the creep data for a group of webbing specimens, and to allow uncontrolled thermal effects to influence the creep data of a second group of webbing specimens. Comparison of both sets of data will define how temperature influences creep data. A unique creep test facility was fabricated to facilitate the generation and comparison of the two sets of data. The facility consists of five creep test stands with an integrated heating and cooling system, and four creep test stands exposed to external environmental or ambient conditions. The facility contains displacement, temperature, humidity, and load sensors. Test specimens consist of one- inch wide, 48-inch long Vectran webbings rated at 12,500 pounds-per-inch. Experimental thermally controlled creep-strain data has been generated for two groups of webbing specimens. Applied load for all test stands was above 9000 lbs and greater than 50 percent of the rated load. Temperatures varied between 58˚F and 83˚F for the four test stands exposed to ambient conditions. Associated creep data exhibited the classic creep- strain profiles. The temperature was set to 72˚F for the five test stands in the controlled temperature environment. Creep data for tests with temperature control also exhibited the classic strain profiles. Data indicated that if the load is greater n thermal effects do not manifest. Therefore, creep tests with loads less than 50 percent of the rated load are planned for in the near future.

Kenner, Winfred S.↗
NASA NTRS1977

Flight-test measurements of ground effect - STOL airplanes

Powered-lift STOL aircraft exhibit special aerodynamic characteristics that necessitate changes in established procedures of flight testing. Methods used in ground-effect flight testing of STOL-configured aircraft are described, with special emphasis on results obtained from tests of the YC-15 AMST prototype aircraft. Ground effect on lift and on drag is theoretically analyzed in terms of trailing vortices, bound vortex, and flight-path angle. Airspeed static source position errors are induced by ground constraint and must be considered in the data reduction. Flight-test results show a positive lift increment due to ground proximity.

Parks, E. K.↗
NASA NTRS2015

Hexavalent Chrome Free Coatings for Electronics Electromagnetic Interference (EMI) Shielding Effectiveness (SE) Interim Test Report

Test specimen configuration was provided by Parker Chomerics. The EMI gasket used in this project was Cho-Seal 6503E. Black oxide alloy steel socket head bolts were used to hold the plates together. Non-conductive spacers were used to control the amount of compression on the gaskets. The following test fixture specifications were provided by Parker Chomerics. The CHO‐TP09 test plate sets selected for this project consist of two aluminum plates manufactured to the specifications detailed in CHO­‐TP09. The first plate, referred to as the test frame, is illustrated in Figure 1. The test frame is designed with a cutout in the center and two alternating bolt patterns. One pattern is used to bolt the test frame to the corresponding test cover plate (Figure 2), forming a test plate set. The second pattern accepts the hardware used to mount the fully assembled test plate set to the main adapter plate (Figure 3).

trivalent chromium↗