Search NASA⌕ Search

SEARCH · Search NASA

Results for “Bonded Joints”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

On the Sensitivity of Piezoceramics and Piezopolymers in Structural Integrity Monitoring of Large Trusses

An analytical assessment has been made of the reliability of using integrated microactuators and sensors in the form of piezoceramics and piezopolymers as joint integrity monitors in trussed systems. The concept is first implemented for a simple structure which consists of two truss members with a 45 deg lift angle joined at the apex. A piezoceramic patch (or piezopolymer film) bonded on the surface of one of the members at a location near the joint is used as a collocated actuator/sensor. The overall structural dynamic response under an excitation was modeled by finite element method. Different degrees of nodal constraints at the joints representing various degrees of joint integrity are employed. The resulting dynamic response showed distinct responses for varying joint stiffnesses. Parallel experimental work on a truss model using a multichannel data acquisition system and a digital signal analyzer confirms the results from analysis. We further studied the sensitivity of the micro-sensors to the behavior of joints of large arch truss structure. Results obtained for large trusses with many degrees of freedom indicate optimum locations of sensors for which the dynamic response signatures are distinct and distinguishable for relatively small changes in joint integrity and/or structural geometry. Computations based on finite element modeling show that locating the single actuator/sensor at the joint corresponding to the first loss of static stability appear optimal. Hence, static stability analysis of complex trusses can give us a good indication of the optimum placement of sensors for maximum response. This observation is important if few distributed sensors and actuators are available for placement in constructed facilities made from large trusses with many degrees of freedom. As an extension of this work a dynamic response signature identification technique to monitor in-service degradation of joints is under development for application to the monitoring of the integrity of adhesive joints in composite structures.

Abatan, A. O.↗
DOE OSTI2025

Formation of Composite SiC/SiC Joints by Embedded Wire Chemical Vapor Deposition

The joining of ceramic monoliths or composites to date has primarily been limited to the formation of brittle monolithic joints using heterogeneous (dissimilar) materials, similar to brazing in metals. The development of a damage-tolerant joint layer by SiC fiber reinforcements is demonstrated here. Tube workpieces made of SiC fiber-SiC matrix composite are joined using a nonwoven SiC fiber mat densified by embedded wire chemical vapor deposition (EWCVD), creating a fiber-reinforced weld-like joint by homogeneous joining. EWCVD uses a localized heating method to target deposition and growth to the joint region specifically, while minimizing thermal damage to the surrounding composite tube material. X-ray computed tomography (XCT) is used to nondestructively characterize as-made joints for relative density, adhesion, and composition. In situ XCT analysis during mechanical testing revealed crack deflections in the bonding layer, which indicates a toughening mechanism typical of ceramic matrix composite phase. Gas permeation testing of these proof-of-concept composite joints identified relatively high leak rates in comparison to fully coated SiC/SiC composite tube workpieces. In conclusion, the novelty of the composite joining method and current technology challenges, including gas permeability, are discussed in comparison with traditional ceramic joints and materials.

SiC↗
DOE OSTI2023

Interfacial bond characterization of epoxy adhesives to aluminum alloy and carbon fiber-reinforced polyamide by vibrational spectroscopy

Vibrational spectroscopic technique has been utilized to investigate interfacial bonding chemistry of two epoxy adhesive products, XP0012 and XP5005F, on plasma-treated AA6061 and carbon fiber-reinforced polyamide 66 (CFRP-PA66) surfaces. The change in vibrational peak ratios was measured by attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy to deduce bonding mechanisms. Both adhesives showed strong crosslinking polymerization of hydroxyl- and amine-initiated epoxy ring opening on AA6061 surface, but on CFRP surface XP0012 formed a simple amide linkage by the reaction of surface hydroxyl groups and nitrile groups of curing agent, and XP5005F formed a crosslinked network by hydroxyl-initiated epoxy ring opening polymerization. The different interfacial bonding formation of two adhesives on CFRP-PA66 surface is attributed to additive effect. Addition of additives to epoxy adhesives (XP5005F) changed the interfacial bonding mechanism on CFRP-PA66 surface, rather forming hydroxyl-initiated epoxy opening crosslinking polymerization than a simple amide bond formation (XP0012). The interfacial bonding chemistry was also proved by addition of bisphenol A (BA) to a simplified model diglycidyl ether of bisphenol A/dicyandiamide (DGEBA/DICY) epoxy system. When BA was added to the model DGEBA/DICY system, epoxy ring gradually decreased on CFRP-PA66 surface, while without BA, DGEBA/DICY showed only decrease in a nitrile peak intensity in ATR-FTIR. In conclusion, the foregoing different types of interfacial chemical bonds at the adhesive/CFRP-PA66 interfaces can affect the lap shear behavior of the joint.

36 MATERIALS SCIENCE↗
NASA NTRS2007

Optical Fiber Distributed Sensing Structural Health Monitoring (SHM) Strain Measurements Taken During Cryotank Y-Joint Test Article Load Cycling at Liquid Helium Temperatures

This paper outlines cryogenic Y-joint testing at Langley Research Center (LaRC) to validate the performance of optical fiber Bragg grating strain sensors for measuring strain at liquid helium temperature (-240 C). This testing also verified survivability of fiber sensors after experiencing 10 thermal cool-down, warm-up cycles and 400 limit load cycles. Graphite composite skins bonded to a honeycomb substrate in a sandwich configuration comprised the Y-joint specimens. To enable SHM of composite cryotanks for consideration to future spacecraft, a light-weight, durable monitoring technology is needed. The fiber optic distributed Bragg grating strain sensing system developed at LaRC is a viable substitute for conventional strain gauges which are not practical for SHM. This distributed sensing technology uses an Optical Frequency Domain Reflectometer (OFDR). This measurement approach has the advantage that it can measure hundreds of Bragg grating sensors per fiber and the sensors are all written at one frequency, greatly simplifying fiber manufacturing. Fiber optic strain measurements compared well to conventional strain gauge measurements obtained during these tests. These results demonstrated a high potential for a successful implementation of a SHM system incorporating LaRC's fiber optic sensing system on the composite cryotank and other future cryogenic applications.

Allison, Sidney G.↗
NASA NTRS2016

Joining and Integration of Silicon Carbide-Based Materials for High Temperature Applications

Advanced joining and integration technologies of silicon carbide-based ceramics and ceramic matrix composites are enabling for their implementation into wide scale aerospace and ground-based applications. The robust joining and integration technologies allow for large and complex shapes to be fabricated and integrated with the larger system. Potential aerospace applications include lean-direct fuel injectors, thermal actuators, turbine vanes, blades, shrouds, combustor liners and other hot section components. Ground based applications include components for energy and environmental systems. Performance requirements and processing challenges are identified for the successful implementation different joining technologies. An overview will be provided of several joining approaches which have been developed for high temperature applications. In addition, various characterization approaches were pursued to provide an understanding of the processing-microstructure-property relationships. Microstructural analysis of the joint interfaces was conducted using optical, scanning electron, and transmission electron microscopy to identify phases and evaluate the bond quality. Mechanical testing results will be presented along with the need for new standardized test methods. The critical need for tailoring interlayer compositions for optimum joint properties will also be highlighted.

Ceramic Matrix Composites↗
DOE OSTI2020

Dark Lock-in Thermography Identifies Solder Bond Failure as the Root Cause of Series Resistance Increase in Fielded Solar Modules

Correlating the electrical performance of photovoltaic modules to the spatially resolved photoluminescence, electroluminescence, and dark lock-in thermography (DLIT) images is an important long-term goal for developing solar cell technology. These images offer highly sophisticated and detailed information about the spatial distribution and (if imaged at successive time intervals) temporal degradation of local series and shunt resistances. There have been extensive studies to correlate these imaging techniques to local characteristics at the cell level. However, it has been difficult to extract and quantify module-level information from the techniques. In this study, we interpret module current-voltage (I-V) measurements along with corresponding DLIT images within a module-scale simulation framework, demonstrating that series resistance degradation of the module I-V characteristics, in this case, can be attributed to solder bond failures. Our simulations highlight how current crowding associated with a failed solder joint (or a section of the solder pad) translates to the characteristic point-like (asymmetric doublet) heating pattern in neighboring solder joints (or the neighboring regions of the solder pad). Overall, the correlation between series resistance and solder joint degradation could inform expedited diagnosis of field degradation of solar modules.

42 ENGINEERING↗
NASA NTRS1985

Improved stud configurations for attaching laminated wood wind turbine blades

A series of bonded stud design configurations was screened on the basis of tension-tension cyclic tests to determine the structural capability of each configuration for joining a laminated wood structure (wind turbine blade) to a steel flange (wind turbine hub). Design parameters which affected the joint strength (ultimate and fatigue) were systematically varied and evaluated through appropriate testing. Two designs showing the most promise were used to fabricate addiate testing. Two designs showing the most promise were used to fabricate additional test specimens to determine ultimate strength and fatigue curves. Test results for the bonded stud designs demonstrated that joint strengths approaching the 10,000 to 12,000 psi ultimate strength and 5000 psi high cycle fatigue strength of the wood epoxy composite could be achieved.

Fadoul, J. R.↗
DOE OSTI2026

Screening and qualification methodology for SiC end plug processing methods

Deployment of SiC-ceramic-based fuel cladding for light water reactors requires a hermetic end plug–to–cladding joint that can withstand neutron irradiation during normal operation and maintain integrity during design-basis accidents. Reactor experiments have shown that some SiC composite tubes with SiC end plugs can retain hermeticity after irradiation. However, achieving consistent joint performance under irradiation remains a key challenge. Resolving this issue is essential to enable integral irradiation testing and to demonstrate fuel integrity under commercial-reactor irradiation conditions. This report aims to: (1) provide guidance for designing radiation-tolerant end plug joints for SiC cladding; (2) demonstrate experimental methods to detect processing defects that are unstable under neutron irradiation at light-water-reactor-relevant temperatures and doses; and (3) outline a step-by-step approach for designing and conducting reactor experiments to screen joining methods. The resulting data will be used to improve joint processing and to define critical defect types and sizes that must be detected and eliminated through non-destructive evaluation for quality assurance. Based on prior irradiation experiments at the High Flux Isotope Reactor, differential swelling among the cladding, bonding layer, and end plug was identified as an underlying mechanism for irradiation-induced joint degradation. Accordingly, this effect must be considered in the design of radiation-tolerant joining techniques. In this work, miniature SiC end plug joint specimens irradiated during the previous project were analyzed using X-ray computed tomography to characterize the joint microstructure. Digital volume correlation of the tomography data quantified radiation-induced microstructural changes and enabled evaluation of defect-related risks. Finally, ongoing neutron irradiation efforts using larger specimen volumes are presented. These efforts aim to statistically assess joint performance and to build a microstructure–performance (e.g., leak-tightness) dataset to inform processing improvements and quality control.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2004

Thermally Conductive Metal-Tube/Carbon-Composite Joints

An improved method of fabricating joints between metal and carbon-fiber-based composite materials in lightweight radiators and heat sinks has been devised. Carbon-fiber-based composite materials have been used in such heat-transfer devices because they offer a combination of high thermal conductivity and low mass density. Metal tubes are typically used to carry heat-transfer fluids to and from such heat-transfer devices. The present fabrication method helps to ensure that the joints between the metal tubes and the composite-material parts in such heat-transfer devices have both (1) the relatively high thermal conductances needed for efficient transfer of heat and (2) the flexibility needed to accommodate differences among thermal expansions of dissimilar materials in operation over wide temperature ranges. Techniques used previously to join metal tubes with carbon-fiber-based composite parts have included press fitting and bonding with epoxy. Both of these prior techniques have been found to yield joints characterized by relatively high thermal resistances. The present method involves the use of a solder (63 percent Sn, 37 percent Pb) to form a highly thermally conductive joint between a metal tube and a carbon-fiber-based composite structure. Ordinarily, the large differences among the coefficients of thermal expansion of the metal tube, solder, and carbon-fiber-based composite would cause the solder to pull away from the composite upon post-fabrication cooldown from the molten state. In the present method, the structure of the solder is modified (see figure) to enable it to deform readily to accommodate the differential thermal expansion.

Copeland, Robert J.↗
NASA NTRS1987

Universal connectors for joining stringers

This invention is a lightweight, universal connector that joins stringers at various angles. The connectors 10 are fabricated from fiber-epoxy resin strips that wrap around stringers 30 and have ends, tabs 16 and 18, which extend in one general direction. The inside surface of the first tab 16 lies on a plane defined by the stringers being joined, and the second tab 18 is separated from the first tab 16 by a distance equal to their thickness. Stringers 30 of different shapes and sizes are joined by alternately bonding the first tab 16 of one connector between the first 16 and second 18 tabs of another connector. Tee-joints are formed by using web elements 41 and 42 which each partially wrap around a stringer 3010 and have tabs 411 and 421 which are offset, and are bonded between tabs 16 and 18 of universal connectors 109 and 1010 bonded to another stringer 309. Sharp corners are trimmed from the tabs so that a gusset area remains between the stringers for support. Acute angle through obtuse angle joints are formed by trimming those edges of the tabs which lie against the stringers. A specific application of the invention is a Walker 60, utilized by handicapped individuals, fabricated from composite materials that is 40% lighter than similar metallic structures.

Harrison, Jr., Ernest↗
NASA NTRS2020

Molecular Dynamics Investigation of the Structural and Mechanical Properties of Off-Stoichiometric Epoxy Resins

We carried out molecular dynamics (MD) simulations to measure the mechanical properties of various off-stoichiometric polymers regarding amine to epoxy ratios (r) and to understand the stiffness of the polymers in terms of their structures. The aerospace-grade API-60 epoxy resin is used as an adhesive bond for assembling large-scale composite structures via the co-curing-ply bonding method. This method will produce a reliable and certifiable composite joint without additional fasteners. Calculated Young's modulus was measured from the uniaxial tension simulation with several high strain rates, and the experimental modulus was estimated by extrapolating the simulation results. We found that the stiffness was associated with molecular packing caused by chemical cross-linking. We also found that the number of network clusters gradually decreased as the ratio approached r = 1.0, which made the tighter cluster and the system much stiffer with an increase in the molecular weight and the degree of cross-linking. Structural properties such as Rg, MSD were measured to figure out the degree of stiffness with respect to the r.

Jang, Chang Woon↗
NASA NTRSDate not supplied

Innovations in Continuous Ultrasonic Welding of Thermoplastic Composites and Evaluation for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗
NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include and assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities, including failure prediction of thermoplastic composites including joints. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite system were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding candidate materials by common welding techniques to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗
NASA NTRS1973

Manufacture of large, lightweight parabolic antennas

Antenna was produced in segments. Parabole sections were built up as aluminum foil sandwich with core bonded by film adhesive; whole structure was oven-cured after assembly. Structure was assembled with special tool for splice-bonding segments into complete dish, and inflatable bladder to apply pressure at joints during cure.

Hooper, S. W.↗
NASA NTRSDate not supplied

Manufacture, Characterization, and Fusion Welding of Thermoplastic Composites for Space Applications

The goals of NASA’s Thermoplastic Development for Exploration Applications (TDEA) Project include an assessment of thermoplastic composite joints for space structures by developing and maturing design capabilities, analysis tools and techniques, and manufacturing processes for thermoplastic composites. Through this effort the TDEA project will expand NASA’s in-house thermoplastic composite manufacturing capabilities, develop an understanding of advanced thermoplastic joining techniques relevant to space environments, evaluate the feasibility of reconfigurable composite structures, and advance structural analysis capabilities. This presentation will provide an overview of the materials and manufacturing effort within the TDEA project. Three semi-crystalline and one amorphous thermoplastic composite materials were selected for initial screening and provided an opportunity to gain manufacturing experience across a range of processing temperatures, rheological behavior, and composite properties. Equivalency to the National Center for Advanced Materials Performance (NCAMP) test report for Toray’s TC1225 material was established to provide confidence in in-house manufacturing and material properties were generated through baseline mechanical tests for each material. Material characterization data was generated for a subset of materials to (1) provide data for analysis and model development and (2) generate thermal, rheological and conductivity data across relevant temperatures. A key objective of the TDEA project is evaluation of thermoplastic composite joining processes suitable for in-space operations. This presentation will outline the project’s progress in fusion bonding of candidate materials to assess the quality, reproducibility and strength of the bond, as well as identify limitations to in-space manufacturing. The feasibility of joint disassembly and reassembly will be discussed.

thermoplastic composite↗
DOE OSTI2020

Numerical Simulation and Experimental Validation of Joint Performance in Aluminum-Steel Lap Welds Formed by Friction Stir Dovetailing

Friction stir dovetailing (FSD) is a new dissimilar material joining process that simultaneously forms a mechanical interlock and metallurgical bond at the dissimilar material interface. This work presents development of a modeling and simulation approach to predict mechanical performance of FSD thick section aluminum to steel joints. A finite element analysis (FEA) was carried out in order to predict the load-carrying capacity and failure location for aluminum thicknesses between 12.7 mm and 50.8 mm with different numbers of dovetails. The numerical results and corresponding experimental investigation are in agreement and suggest that the developed methods can be used effectively for design and analysis of FSD joints using standard FEA tools.

Friction stir dovetailing, Friction stir welding, ↗
NASA NTRS1972

Thin-film diffusion brazing of titanium alloys

A thin film diffusion brazing technique for joining titanium alloys by use of a Cu intermediate is described. The method has been characterized in terms of static and dynamic mechanical properties on Ti-6Al-4V alloy. These include tensile, fracture toughness, stress corrosion, shear, corrosion fatigue, mechanical fatigue and acoustic fatigue. Most of the properties of titanium joints formed by thin film diffusion brazing are equal or exceed base metal properties. The advantages of thin film diffusion brazing over solid state diffusion bonding and brazing with conventional braze alloys are discussed. The producibility advantages of this process over others provide the potential for producing high efficiency joints in structural components of titanium alloys for the minimum cost.

Mikus, E. B.↗