Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Effects of CeO{sub 2} on the Microstructure and Properties of Laser Cladding 316L Coating

Laser cladding was used to distribute a CeO{sub 2}-modified 316L powder coating onto a 316L stainless steel surface. The cladding layer phase composition was evaluated through x-ray diffraction. An analysis of the microstructure was conducted using an optical microscope and scanning electron microscope, while the micro-hardness was measured using a tester. The coating corrosion behavior in response to 3.5% NaCl solution was analyzed by polarization curves and electrochemical impedance spectroscopy. Finally, the overall performance of coatings with different CeO{sub 2} concentrations, 1, 2, and 3%, was compared. Results showed that adding CeO{sub 2} significantly refined the grains, reduced the coating porosity, and effectively limited the appearance of local corrosion. Also, additive CeO{sub 2} shifted the coating’s electrode potential in a positive direction, minimizing the current density of corrosion, creating a stable passivation film, and improving the coating’s corrosion resistance. The coating performance (hardness and corrosion behavior) was optimal when 2% CeO{sub 2} was employed as the powder mass.

36 MATERIALS SCIENCE↗

Material selection for accident tolerant fuel cladding

Alternative cladding materials are being investigated for accident tolerance, which can be defined as >100X improvement (compared to current Zr-based alloys) in oxidation resistance in steam environments at ≥1200°C for short (≤4 h) times. After reviewing a wide range of candidates, current steam oxidation testing is being conducted on Mo, MAX phases and FeCrAl alloys. Recently reported low mass losses for Mo in steam at 800°C could not be reproduced. Both FeCrAl and MAX phase Ti 2 AlC form a protective alumina scale in steam. Therefore, commercial Ti 2 AlC that is not single phase, formed a much thicker oxide at 1200°C in steam and significant TiO 2 , and therefore may be challenging to use as a cladding or a coating. Alloy development for FeCrAl is seeking to maintain its steam oxidation resistance to 1475°C, while reducing its Cr content to minimize susceptibility to irradiation assisted Cr-rich α’ formation. The composition effects and critical limits to retaining protective scale formation at >1400°C are still being evaluated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON validation to in situ cladding burst test and high-burnup LOCA experiments

The process for developing and qualifying nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and postirradiation examinations; and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes ~20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In situ measurements generally provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the US nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the US Nuclear Regulatory Commission (NRC) outlined in its research information letter several technical issues that the industry must address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heat-up phase. By leveraging these advanced in situ capabilities, this work used in situ data generated from a simulated LOCA to better understand high-temperature creep and its effect on Zircaloy balloon and rupture performance. Here, this work used the BISON fuel performance code to assess the high-temperature creep model predictions with in situ data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Understanding the high-temperature behavior and corrosion resistance of Cr-Nb coated cladding for BWRs

While Cr-coated Accident Tolerant Fuel has proven successful in Pressurized Water Reactors, its dissolution in high dissolved oxygen Boiling Water Reactor environments represents a major technological barrier. Here, this study presents a comprehensive evaluation of novel Cr-Nb alloys as a coating breakthrough solution for Accident Tolerant Fuel cladding in Boiling Water Reactors. We systematically investigated Physical Vapor Deposited Cr-Nb coatings with 13% and 24 at% Nb content on commercial Zr-based cladding through rigorous testing under both normal and accident conditions. Our results demonstrate Cr-Nb coatings remained completely intact during extended Boiling Water Reactor autoclave testing, while pure Cr coatings failed catastrophically due to oxide dissolution. Under Loss-of-Coolant Accident conditions at 1100°C, Cr-Nb coatings maintained protective capability for 45 min. At 800°C, the alloy coatings matched pure Cr's excellent corrosion resistance. Despite microstructural changes during prolonged high-temperature exposure, no coating delamination occurred, ensuring continued protection of the underlying Zr substrate. These findings establish Cr-Nb coatings as a viable Accident Tolerant Fuel solution for Boiling Water Reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Raman and XPS characterization of fuel-cladding interactions using miniature specimens

Laser Raman spectroscopy was evaluated as a tool for studying fuel-cladding chemical interactions at elevated temperatures. Materials and conditions were selected to simulate the interface of oxide fuels and fission products with high-temperature cladding materials for TRU-MOX fueled reactors. Both ex-situ and in-situ spectroscopy measurements were performed using polished HT-9 disks, uncoated and coated with yttria-stabilized zirconia, that were exposed to air oxidation at temperatures between 873-973K. Ex-situ measurements (under ambient conditions) were conducted to identify oxide phases, determine oxidation mechanisms and approximate film growth rates with an optimal signal-to-noise for the equipment used. Subsequently performed in-situ measurements were used to evaluate the sensitivity of the technique for measurements at elevated temperature in a hot-stage. Raman spectra were supported with x-ray photoelectron spectroscopy depth profiling. The results, which are for non-fueled materials in this study, illustrated a method for fast screening of candidate alloys with actinide-based MOX fuel mixtures.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Characterization and mechanical properties of cladded stainless steel 316L with nuclear applications fabricated using electron beam melting

The ability to fabricate or join components of 316 L austenitic stainless steel using additive manufacturing (AM) processes such as laser and electron beam melting (EBM®) offers several advantages including enhanced part complexity, narrow or absent heat affected zones, increased part precision, avoidance of filler materials (such as traditional welds), and the ability to create metallurgically sound bonds. These attributes can contribute to improved mechanical properties of the fabricated components and component repair in nuclear, aerospace, and chemical industries. In the present work, we report that austenitic 316 L stainless steel additively manufactured by EBM exhibits a 76% increase in the yield strength and a corresponding increase of 29% in the ultimate tensile strength in contrast to the wrought substrate and commercial forged 316 L stainless steel. The EBM clad 316 L stainless steel elongation was 36%. The wrought substrate equiaxed grain size was ~30 μm in contrast to elongated, columnar grains ~0.1 mm wide and >1 mm in length for the EBM cladding. Transmission Electron Microscopy (TEM) analysis revealed that these columnar grains, which exhibited very straight, and presumably special grain boundaries having a very high (100) texture, contained a variety of sub-grain microstructures consisting of low-angle sub-grain boundaries containing dislocation tangles and stacking-fault arrays, and homogeneously distributed Cr 23 C 6 carbide precipitates, with no preferential carbide precipitation on either the straight, special columnar grain boundaries, or the very low-angle sub-grain boundaries. This observation and the formation of hierarchical microstructures which produce high strength and possibly corrosion resistance as a consequence of the absence of grain boundary carbide precipitation, illustrate the prospects for AM as a novel concept for achieving grain boundary engineering to promote high-strength and corrosion resistant alloys for high-temperature, corrosive environments, including elevated temperature nuclear reactor applications.

36 MATERIALS SCIENCE↗

A correlation-based approach for evaluating mechanical properties of nuclear fuel cladding tubes

The present work offers and evaluates a correlation-based approach to determine the tensile properties of nuclear fuel cladding tubes. A set of model materials with known properties (i.e., austenitic and ferritic steels, fcc- and hcp-alloys) were tested to build a correlation between conventional tensile tests and ring (hoop) and tube (axial) tests. It was shown that close-to-linear relationships exist for the basic mechanical properties (i.e., yield and ultimate stress, uniform and total elongation) between the uniaxial tensile test data and the ring and tube test data. Using the ring and tube specimen geometries, the feasibility of the approach was demonstrated via manufacturing and testing specimens from irradiated Zr and FeCrAl nuclear fuel cladding tubes. Limitations caused by specific deformation mechanisms (e.g., high ductility of 304L steel) were discussed in detail. The approach can be extended to other tubular products with different geometry and dimensions.

36 MATERIALS SCIENCE↗

Microstructure and microchemistry changes at U-10Mo fuel/AA6061 cladding interfaces with varying hot isostatic pressing conditions

Monolithic uranium - 10 wt.% molybdenum (U-10Mo) is a promising high-assay low-enriched uranium fuel system for nuclear reactors used in research, medical isotope production, and remote power applications. During manufacturing, AA6061 cladding is bonded to the U-10Mo fuel plate via hot isostatic pressing, during which diffusion and fuel/cladding chemical interaction occurs at plate edges. Furthermore, the microstructure and microchemistry changes that occur at fuel/cladding interfaces are important to understand as a function of process parameters to develop a reliable fuel fabrication process and to meet the desired specifications. Here, microstructural and microchemical changes are studied using complementary electron microscopy and atom probe tomography for two manufactured fuel plates with varied hot isostatic pressing (HIP) parameters. Results highlight that modifying thermomechanical processing parameters significantly changed the interaction layer thickness between U-10Mo and AA6061 by an order of magnitude. In addition to this the distribution and concentration of elements (i.e., Al, Si, Mg) from cladding to fuel was also investigated.

36 MATERIALS SCIENCE↗

In-situ determination of strain during transient burst testing and the temperature dependence of Zircaloy-4 claddings

Understanding fuel system behavior during postulated loss-of-coolant accidents is pertinent for continued safe and efficient operation of light water reactors, particularly as higher burnups are being pursued and safety margins re-evaluated. Conventional mechanical models for the incumbent Zr alloys typically rely on the assumption that steady-state creep is the dominant fuel cladding response during transient accident conditions. To investigate this assumption, simulated accident burst testing was performed on Zircaloy-4 claddings with balloon behavior measured in-situ. Here, two distinct loading conditions were utilized during burst testing: (1) constant-gas-inventory where pressure was allowed to increase with temperature and (2) constant pressure. In-situ strains and strain rates were measured via 2-dimensional digital image correlation techniques and synchronized with temperature to determine deformation dependencies. The temperature dependence of strain rate was characterized by a two segment Arrhenius relationship, with a distinct transition between the high and low temperature/strain regimes. The average activation energy of the lower temperature/strain regime was 328 ± 25 kJ/mol, in agreement with the ~320 kJ/mol used for conventional LOCA models. However, the higher temperature/strain segment, which encompassed most of ballooning, showed increased activation energies as well as a dependence on whether the burst region was in view. For tests that burst away from the camera view, the average high temperature/strain segment activation energy was 635 ± 150 kJ/mol. For samples where the rupture opening formed in view, the average activation energy was 1015 ± 179 kJ/mol. This observed shift in temperature dependence indicates a transition in deformation mechanism at the end of life, possibly to time independent failure mechanisms, which has not yet been visualized in the literature for Zr alloys. Parameters at the transition points were analyzed to determine thresholds for this change in behavior, which occurred at an average hoop strain of 6.9 ± 2.1 %.

36 MATERIALS SCIENCE↗

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗

Metallic fuel transient fuel-cladding interface liquefaction model assessment platform enabled by integrating BISON with databases

A novel platform has been developed within the BISON fuel performance code to assess models of fuel-cladding interface liquefaction for sodium-cooled fast reactor (SFR) metallic fuels. Here, this platform is crucial because liquefaction at the fuel-cladding interface significantly impacts fuel performance and may compromise fuel pin integrity during transient events. To ensure accurate predictions, the platform integrates data collected during the Integral Fast Reactor (IFR) program, now archived in metallic fuel databases. This integration supports verification and validation (V&V) of the models in BISON. Leveraging the extensive US experience with metallic fuel liquefaction and the collections of preserved legacy data, the platform serves as a powerful tool for evaluating existing models and advancing the development of new ones.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Site-specific nanoscale characterization of zirconium hydrides in the hydride rim structure of hydrogen-charged zircaloy-4 cladding

Zircaloy-4 cladding tubes were hydrogen-charged using a static pressure hydrogen charging method to experimentally produce a zirconium-hydride rim structure similar to that observed in Zircaloy-4 cladding tubes after operation in commercial light-water nuclear reactors. Detailed characterization was performed using electron energy loss spectroscopy (EELS) and four-dimensional scanning transmission electron microscopy (4D-STEM). By mapping the position of the plasmon peak in the low-loss EELS spectrum, it was determined that the zirconium hydrides formed were predominantly solid δ-phase zirconium hydrides. 4D-STEM was used to generate phase and strain maps at nanoscale. The interactions between two zirconium hydride platelets less than 200 nm apart leads to the localized lattice rotations and possible phase change, revealing a potential hydride growth mechanism.

4D-STEM↗

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material

Silicon carbide (SiC)-based nuclear fission fuel rod cladding has been considered as one of the possible designs for accident tolerant fuels. It is in the form of a SiC fibre reinforced SiC matrix composite tube (SiC f -SiC m ) with monolithic SiC outer and/or inner coating layers. This study focuses on the deformation and fracture processes in this material using in situ X-ray micro-computed tomography (XCT) at room temperature (RT) and 1200 °C in an inert gas environment in a C-ring compression loading configuration. Prior to testing, local properties and residual stresses were characterised using nanoindentation and Raman spectroscopy since they can impact the mechanical behaviour of the material. The 3D strain distribution, crack formation and propagation processes including the toughening mechanisms (e.g., crack deflection, micro-cracking, crack bridging and bifurcation) are investigated in the coating and underlying composites at RT and 1200 °C. There is no particular sequence which toughening mechanism occurs first – this is very different from the conventional toughening theory in ceramic-matrix composites under uniaxial tension loading. Indeed, no evidence of fibre pull-out or fibre fracture was observed in this SiC f -SiC m nuclear cladding material in the current C-ring compression configuration. The correlation between local measurements and bulk mechanical behaviour are discussed.

3D imaging↗

Assessment of the analysis capability for core-wide PWR pellet-clad interaction screening of Watts Bar Unit 1

This report illustrates the application of the Virtual Environment for Reactor Applications simulation environment to pressurized water reactor core-wide pellet-clad interaction screening, with emphasis on the multi-dimensional analysis capabilities of the BISON fuel performance code. The Virtual Environment for Reactor Applications codes utilized in this effort include the BISON fuel performance code and the VERA-CS sub-element, which combines the MPACT neutron transport code and the COBRA-TF thermal-hydraulics code. The target reactor for this work is Watts Bar Unit 1, cycle 6 and cycle 7, selected on the basis that pellet-clad interaction failures had occurred during power start up in both cycles, despite the moderate power levels. These instances of failure at Watts Bar Unit 1 offered an interesting test of the code’s veracity and a particularly challenging condition for this assessment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Pool boiling critical heat flux studies of accident tolerant fuel cladding materials

Pool boiling experiments have been performed at atmospheric pressure on potential accident tolerant fuel (ATF) cladding materials (Zirlo®, Cr coated Zirlo®, FeCrAl coated Zirlo®, and monolithic SiC) to evaluate the Critical Heat Flux (CHF) points. Corrosion resistant coatings of Cr and FeCrAl alloy were deposited on flat Zirlo® samples using cold spray technology. The as-prepared samples after uniform surface polishing were subjected to autoclave tests at 360 °C water and 18.6 MPa for 360 h to simulate prototypic corrosion of the ATF cladding materials in LWR normal operation. Surface characteristics potentially influencing CHF such as surface morphology, roughness, static contact angle, and surface chemistry were characterized using a suite of characterization methods including scanning electron microscopy, 3D optical profilometry, optical contact angle measurements, and x-ray photoelectron spectroscopy (XPS). Thermo-physical properties of the samples such as density, thermal conductivity, and heat capacity were measured by differential scanning calorimetry and laser flash thermal diffusivity measurement. FeCrAl coatings showed CHF values comparable to bare Zirlo® samples, while slightly lower CHF values were observed for Cr coated samples and bulk SiC flats (produced by chemical vapor deposition, CVD). As-deposited Cr coatings showed 67% higher CHF than the as-polished Cr coatings due to its higher surface roughness level. The autoclave testing for the prepared samples generally increased the CHF except for the surface polished Cr coatings. Similar CHF values of bare Zirlo®, FeCrAl coating, and CVD SiC samples were observed after autoclave test but there were negligible change CHF of Cr coatings. XPS studies indicated that the formation or deposition of a few monolayers of hydrophobic carbonaceous species on surface can affect CHF values. The trends in CHF data are discussed in terms of evolution of the surface characteristics of the ATF materials.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Development of cone-wedge-ring-expansion test to evaluate the tensile HOOP properties of nuclear fuel cladding

Here, we report the development of a cone wedge ring expansion test method to determine the tensile hoop properties of irradiated nuclear fuel cladding in a hot cell. A closed-form solution was developed to explicitly relate the hoop stress σ θ to the axial piston loading using the scale factor χ and the shear stress correction factor α, where the χ and α factors are used to convert the applied piston load and the radial dilatation of the ring into the tensile hoop stress-strain curve. The applicability of this new test method was demonstrated by successfully evaluating ring specimens of Zr-4 alloy to failure. The ring specimens deformed uniformly in the axial and circumferential directions until onset of necking. The χ and α factors were successfully determined by using a finite-element stress analysis that benchmarked with applied test load and total work to account for frictional forces and the associated energies dissipation between the different sliding components of the testing system. The tensile hoop strength values obtained using the proposed cone-wedge-ring-expansion test method were 10% higher than values obtained from the tensile evaluation of the cladding material along the axial direction. In conclusion, the variability in results was found to be within the range reported in the literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Chemical vapor deposition of Mo tubes for fuel cladding applications

In this study, chemical vapor deposition (CVD) techniques have been evaluated for fabrication of free-standing 0.25 mm thick molybdenum tubes with the end goal of nuclear fuel cladding applications. In order to produce tubes with the wall thickness and microstructures desirable for this application, long deposition durations on the order of 50 h with slow deposition rates were employed. A standard CVD method, involving molybdenum pentachloride reduction by hydrogen, as well as a fluidized-bed CVD (FBCVD) method was applied towards these objectives. Characterization of the tubes produced in this manner revealed regions of material with fine grain microstructure and wall thickness suitable for fuel cladding applications, but lacking necessary uniformity across the length of the tubes. Finally, a path forward for the production of freestanding molybdenum tubes that possess the desired properties across their entire length has been identified and can be accomplished by future optimization of the deposition system.

(Fluidized-bed) chemical vapor deposition↗

Microstructural and nanomechanical studies of PVD Cr coatings on SiC for LWR fuel cladding applications

The microstructure and nanomechanical properties of pure Cr coatings deposited on SiC with various physical vapor deposition (PVD) methods have been investigated for the mitigation of hydrothermal corrosion of SiC-SiC f (SiC fiber-reinforced SiC matrix) composite fuel cladding in light water reactors (LWR). Cr coatings (4–7 μm thick) were deposited on unbiased SiC substrates using six variants of magnetron sputtering processes: (i) standard (S-DCMS), (ii) pulsed (P-DCMS), (iii) ion-assisted (I-DCMS), and (iv) pulsed ion-assisted direct current magnetron sputtering (PI-DCMS), (v) high-power impulse magnetron sputtering (HiPIMS), and (vi) bipolar HiPIMS (B-HiPIMS). Microstructural characterization and nanoindentation testing were used to evaluate effects of deposition technique on coating microstructure and nanomechanical properties. The application of positive reverse pulses to the sputter target induced coarsening of the columnar grain structure, while ion bombardment of substrates during deposition promoted densification of the coating microstructure. Both effects are exemplified in B-HiPIMS deposition, resulting in a high-density microstructure with compressive residual stress. Material pile-up around nano-indents and plastic work during nanoindentation were analyzed to understand deformation behavior of the coatings. Finally, the results suggest the B-HiPIMS process to be among the promising methods for the deposition of Cr coatings on SiC-SiC f for LWR cladding application.

36 MATERIALS SCIENCE↗