Search NASA⌕ Search

SEARCH · Search NASA

Results for “Collective modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Earth Resources Technology Satellite Operations Control Center (OCC). ERTS-B flight activation plan

Included in this plan are general objectives through Day 7, operational guidelines and restraints. Following the activation of all subsystems (through Day 3), special series of payload operations were performed to obtain data samples for the different combinations of exposure/gain settings. This took place from Day 4 through Day 7. The Orbit Adjust was employed to perform vernier corrections after the orbit had been defined. The orbit data was collected through Day 3, with the corrections being made from Day 4 through Day 7. ERTS command auxiliary memory (ECAM) was turned on in Day 3 and the memory dumped to a narrow band tape recorder. A verification of memory was done in the off line mode. ECAM was not used in a payload support mode until Day 7.

Source record↗
NASA NTRS1977

Design of satellite flexibility experiments

A preliminary study has been completed to begin development of a flight experiment to measure spacecraft control/flexible structure interaction. The work reported consists of two phases: identification of appropriate structural parameters which can be associated with flexibility phenomena, and suggestions for the development of an experiment for a satellite configuration typical of near-future vehicles which are sensitive to such effects. Recommendations are made with respect to the type of data to be collected and instrumentation associated with these data. The approach consists of developing the equations of motion for a vehicle possessing a flexible solar array, then linearizing about some nominal motion of the craft. A set of solutions are assumed for array deflection using a continuous normal mode method and important parameters are exposed. Inflight and ground based measurements are distinguished. Interrelationships between these parameters, measurement techniques, and input requirements are discussed which assure minimization of special vehicle maneuvers and optimization of data to be obtained during the normal flight sequence.

Kaplan, M. H.↗
NASA NTRS1984

Development of dynamic simulation of TF34-GE-100 turbofan engine with post-stall capability

This paper describes the development of a hybrid computer simulation of a TF34-GE-100 turbofan engine with post-stall capability. The simulation operates in real-time and will be used to test and evaluate stall recovery control modes for this engine. The simulation calculations are performed by an analog computer with a peripheral multivariable function generation unit used for computing bivariate functions. Tabular listings of simulation variables are obtained by interfacing to a digital computer and using a custom software package for data collection and display.

Krosel, S. M.↗
NASA NTRS1985

UNAERO: A package of FORTRAN subroutines for approximating unsteady aerodynamics in the time domain

This report serves as an instruction and maintenance manual for a collection of CDC CYBER FORTRAN IV subroutines for approximating the unsteady aerodynamic forces in the time domain. The result is a set of constant-coefficient first-order differential equations that approximate the dynamics of the vehicle. Provisions are included for adjusting the number of modes used for calculating the approximations so that an accurate approximation is generated. The number of data points at different values of reduced frequency can also be varied to adjust the accuracy of the approximation over the reduced-frequency range. The denominator coefficients of the approximation may be calculated by means of a gradient method or a least-squares approximation technique. Both the approximation methods use weights on the residual error. A new set of system equations, at a different dynamic pressure, can be generated without the approximations being recalculated.

Dunn, H. J.↗
NASA NTRS1995

The acoustic characteristics of turbomachinery cavities

Internal fluid flows are subject not only to self-sustained oscillations of the purely hydrodynamic type but also to the coupling of the instability with the acoustic mode of the surrounding cavity. This situation is common to turbomachinery, since flow instabilities are confined within a flow path where the acoustic wavelength is typically smaller than the dimensions of the cavity and flow speeds are low enough to allow resonances. When acoustic coupling occurs, the fluctuations can become so severe in amplitude that it may induce structural failure of engine components. The potential for catastrophic failure makes identifying flow-induced noise and vibration sources a priority. In view of the complexity of these types of flows, this report was written with the purpose of presenting many of the methods used to compute frequencies for self-sustained oscillations. The report also presents the engineering formulae needed to calculate the acoustic resonant modes for ducts and cavities. Although the report is not a replacement for more complex numerical or experimental modeling techniques, it is intended to be used on general types of flow configurations that are known to produce self-sustained oscillations. This report provides a complete collection of these models under one cover.

Lucas, M. J.↗
NASA NTRS2017

Design and Control of an Experimental Tilt-Wing Aircraft

In this project, work has been done in the field of conceptual design of experimental tiltrotors. The main tools that have been used are NDARC (NASA Design and Analysis of Rotorcraft) and SIMPLI-FLYD. NDARC is a conceptual design tool for rotorcraft, and it is used to find trim points under various flight conditions. SIMPLI-FLYD is an integrated collection of software tools that enables a flight dynamics and control assessment of the rotorcraft vehicle design generated from NDARC. Two different tiltrotors have been investigated. Initially, work was done with the Bell XV- 15 tiltrotor. NDARCs ability to correctly model the tiltwing transition between airplane mode and hover mode was looked into. In addition, data from old flight tests were compared to the NDARC output, to see how accurately performance could be predicted. After the XV-15 analysis, an NDRARC model of a novel tiltwing concept from Elytron Aircraft was written and analyzed together with SIMPLI-FLYD. Elytron 2S is an experimental tiltwing aircraft, consisting of a joined-wing design with a small central wing for the proprotor. An alternative approach to hover control is used, where the typical rotor hub and swash plate are substituted for linear actuators controlling pitch, yaw and roll. The objective with the analysis of Elytron is to obtain a more complete understanding of the maneuverability and possible performance of this alternative aircraft configuration.

Conceptual Design↗
NASA NTRS1984

Development of dynamic simulation of TF34-GE-100 turbofan engine with post-stall capability

This paper describes the development of a hybrid computer simulation of a TF34-GE-100 turbofan engine with post-stall capability. The simulation operates in real-time and will be used to test and evaluate stall recovery control modes for this engine. The simulation calculations are performed by an analog computer with a peripheral multivariable function generation unit used for computing bivariate functions. Tabular listings of a simulation variables are obtained by interfacing to a digital computer and using a custom software package for data collection and display.

Krosel, S. M.↗
NASA NTRS1986

Analytical determination of propeller performance degradation due to ice accretion

A computer code has been developed which is capable of computing propeller performance for clean, glaze, or rime iced propeller configurations, thereby providing a mechanism for determining the degree of performance degradation which results from a given icing encounter. The inviscid, incompressible flow field at each specified propeller radial location is first computed using the Theodorsen transformation method of conformal mapping. A droplet trajectory computation then calculates droplet impingement points and airfoil collection efficiency for each radial location, at which point several user-selectable empirical correlations are available for determining the aerodynamic penalities which arise due to the ice accretion. Propeller performance is finally computed using strip analysis for either the clean or iced propeller. In the iced mode, the differential thrust and torque coefficient equations are modified by the drag and lift coefficient increments due to ice to obtain the appropriate iced values. Comparison with available experimental propeller icing data shows good agreement in several cases. The code's capability to properly predict iced thrust coefficient, power coefficient, and propeller efficiency is shown to be dependent on the choice of empirical correlation employed as well as proper specification of radial icing extent.

Miller, T. L.↗
NASA NTRS2007

Neural Network Burst Pressure Prediction in Composite Overwrapped Pressure Vessels

Acoustic emission data were collected during the hydroburst testing of eleven 15 inch diameter filament wound composite overwrapped pressure vessels. A neural network burst pressure prediction was generated from the resulting AE amplitude data. The bottles shared commonality of graphite fiber, epoxy resin, and cure time. Individual bottles varied by cure mode (rotisserie versus static oven curing), types of inflicted damage, temperature of the pressurant, and pressurization scheme. Three categorical variables were selected to represent undamaged bottles, impact damaged bottles, and bottles with lacerated hoop fibers. This categorization along with the removal of the AE data from the disbonding noise between the aluminum liner and the composite overwrap allowed the prediction of burst pressures in all three sets of bottles using a single backpropagation neural network. Here the worst case error was 3.38 percent.

Hill, Eric v. K.↗
NASA NTRS2011

Cost Modeling for Space Optical Telescope Assemblies

Parametric cost models are used to plan missions, compare concepts and justify technology investments. This paper reviews an on-going effort to develop cost modes for space telescopes. This paper summarizes the methodology used to develop cost models and documents how changes to the database have changed previously published preliminary cost models. While the cost models are evolving, the previously published findings remain valid: it costs less per square meter of collecting aperture to build a large telescope than a small telescope; technology development as a function of time reduces cost; and lower areal density telescopes cost more than more massive telescopes.

Stahl, H. Philip↗
NASA NTRS2013

Cloud Absorption Radiometer Autonomous Navigation System - CANS

CAR (cloud absorption radiometer) acquires spatial reference data from host aircraft navigation systems. This poses various problems during CAR data reduction, including navigation data format, accuracy of position data, accuracy of airframe inertial data, and navigation data rate. Incorporating its own navigation system, which included GPS (Global Positioning System), roll axis inertia and rates, and three axis acceleration, CANS expedites data reduction and increases the accuracy of the CAR end data product. CANS provides a self-contained navigation system for the CAR, using inertial reference and GPS positional information. The intent of the software application was to correct the sensor with respect to aircraft roll in real time based upon inputs from a precision navigation sensor. In addition, the navigation information (including GPS position), attitude data, and sensor position details are all streamed to a remote system for recording and later analysis. CANS comprises a commercially available inertial navigation system with integral GPS capability (Attitude Heading Reference System AHRS) integrated into the CAR support structure and data system. The unit is attached to the bottom of the tripod support structure. The related GPS antenna is located on the P-3 radome immediately above the CAR. The AHRS unit provides a RS-232 data stream containing global position and inertial attitude and velocity data to the CAR, which is recorded concurrently with the CAR data. This independence from aircraft navigation input provides for position and inertial state data that accounts for very small changes in aircraft attitude and position, sensed at the CAR location as opposed to aircraft state sensors typically installed close to the aircraft center of gravity. More accurate positional data enables quicker CAR data reduction with better resolution. The CANS software operates in two modes: initialization/calibration and operational. In the initialization/calibration mode, the software aligns the precision navigation sensors and initializes the communications interfaces with the sensor and the remote computing system. It also monitors the navigation data state for quality and ensures that the system maintains the required fidelity for attitude and positional information. In the operational mode, the software runs at 12.5 Hz and gathers the required navigation/attitude data, computes the required sensor correction values, and then commands the sensor to the required roll correction. In this manner, the sensor will stay very near to vertical at all times, greatly improving the resulting collected data and imagery. CANS greatly improves quality of resulting imagery and data collected. In addition, the software component of the system outputs a concisely formatted, high-speed data stream that can be used for further science data processing. This precision, time-stamped data also can benefit other instruments on the same aircraft platform by providing extra information from the mission flight.

Kahle, Duncan↗
NASA NTRS2018

Fire Induced Rock Spalls as Long-Term Traps for Ash

Severe fires accelerate rock weathering by spalling and exfoliation, creating abundant peels, flakes or spalls. In the following years, these spalls serve as physical traps which accommodate fine particles of dust, ash, organic matter, etc. We searched for traces of ash trapped under the spalls, after four major fires: 1989, 2005, 2010 and 2015 in Israel. Samples were collected beneath the spalls that formed on the rock outcrops, and in the immediate vicinity above and below them. Three laboratory analyses were performed: pH, EC and color. Five mineral/organic compounds were measured across the Mid-Infrared (MIR) spectral region at diffuse reflectance infrared Fourier transform mode: Hydroxylapatite (HAp), charcoal, organic carbon, montmorillonite and kaolinite. Several statistical analyses were performed: MANOVA, PCA and silhouette analysis on K-means clustering. The results show evidence of ash trapped under the spalls formed during the 2005 and 2010 fires, 6 to 11 years after the fires. Charcoal presence is evident, as well as increased amounts of HAp and organic carbon. In the exposed soil above or below the burned rock outcrop, these values are lower. Negligible amounts of ash were measured 27 years after the fire. In the 2015 burned outcrop, large amounts of charcoal were found above and below the outcrop, but not under the spalls. It seems that on the carbonate slopes of Israel and under Mediterranean climate, the time required for spalls to begin functioning as traps is longer than one rainy season, while ash traces are preserved in these traps for a period of two-three decades.

ash↗
NASA NTRS2022

Polarimeter + Lidar–Derived Aerosol Particle Number Concentration

In this study, we propose a simple method to derive vertically resolved aerosol particle number concentration (Na) using combined polarimetric and lidar remote sensing observations. This method relies on accurate polarimeter retrievals of the fine-mode column-averaged aerosol particle extinction cross section and accurate lidar measurements of vertically resolved aerosol particle extinction coefficient such as those provided by multiwavelength high spectral resolution lidar. We compare the resulting lidar + polarimeter vertically resolved N(a) product to in situ N(a) data collected by airborne instruments during the NASA aerosol cloud meteorology interactions over the western Atlantic experiment (ACTIVATE). Based on all 35 joint ACTIVATE flights in 2020, we find a total of 32 collocated in situ and remote sensing profiles that occur on 11separate days, which contain a total of 322 cloud-free vertically resolved altitude bins of 150 m resolution. We demonstrate that the lidar + polarimeter N(a) agrees to within 106% for 90% of the 322 vertically resolved points. We also demonstrate similar agreement to within 121% for the polarimeter-derived column-averaged N(a). We find that the range-normalized mean absolute deviation (NMAD) for the polarimeter-derived column-averaged Na is 21%, and the NMAD for the lidar + polarimeter-derived vertically resolved Na is 16%. Taken together, these findings suggest that the error in the polarimeter-only column-averaged N(a) and the lidar + polarimeter vertically resolved N(a) are of similar magnitude and represent a significant improvement upon current remote sensing estimates of N(a).

RSP↗
NASA NTRS1998

The Recovery of TOMS-EP

On December 13th 1998, the Total Ozone Mapping Spectrometer - Earth Probe (TOMS-EP) spacecraft experienced a Single Event Upset which caused the system to reconfigure and enter a Safe Mode. This incident occurred two and a half years after the launch of the spacecraft which was designed for a two year life. A combination of factors, including changes in component behavior due to age and extended use, very unfortunate initial conditions and the safe mode processing logic prevented the spacecraft from entering its nominal long term storage mode. The spacecraft remained in a high fuel consumption mode designed for temporary use. By the time the onboard fuel was exhausted, the spacecraft was Sun pointing in a high rate flat spin. Although the uncontrolled spacecraft was initially in a power and thermal safe orientation, it would not stay in this state indefinitely due to a slow precession of its momentum vector. A recovery team was immediately assembled to determine if there was time to develop a method of despinning the vehicle and return it to normal science data collection. A three stage plan was developed that used the onboard magnetic torque rods as actuators. The first stage was designed to reduce the high spin rate to within the linear range of the gyros. The second stage transitioned the spacecraft from sun pointing to orbit reference pointing. The final stage returned the spacecraft to normal science operation. The entire recovery scenario was simulated with a wide range of initial conditions to establish the expected behavior. The recovery sequence was started on December 28th 1998 and completed by December 31st. TOMS-EP was successfully returned to science operations by the beginning of 1999. This paper describes the TOMS-EP Safe Mode design and the factors which led to the spacecraft anomaly and loss of fuel. The recovery and simulation efforts are described. Flight data are presented which show the performance of the spacecraft during its return to science. Finally, lessons learned are presented.

Robertson, Brent↗
NASA NTRS1967

Surface-spike growth on NiBr sub 2 crystals - A VLS mode of crystal growth.

Droplets associated with surface-spike growth of crystals of NiBr 2 by sublimation have been analyzed and found to contain Cu, Co, Mn, and Fe in addition to Ni and Br. These elements exist in the bulk of the original charge material in concentrations that are several orders of magnitude lower than that in the droplets. During crystal growth by sublimation the impurities collect on the surface of growing crystals, until sufficient concentrations are reached to cause the nucleation of a metastable liquid phase droplet. Once the liquid phase droplets have been nucleated, they may then become attached to growth steps and produce accelerated growth from these sites. Such processes occur in NiBr 2 , during growth by sublimation, at approximately 500 °C below the melting point of NiBr 2 .

Edward N Sickafus↗
NASA NTRS1973

Model tests on unsteady rotor wake effects.

A qualitative model of unsteady asymmetric wake effects is considered, taking into account a progressing blade flapping mode in which each blade flaps in a rotating frame of reference. The rotor model used for the tests is two bladed. The experimental data are compared with an analytical flapping response. It is found that the steady wake effects are largest at zero advance ratio and low collective pitch. The effects remain significant at higher advance ratios and collective pitch settings.

Hohenemser, K. H.↗
NASA NTRS1978

Oxide morphology and spalling model for NiAl

A scanning electron microscope equipped with an energy dispersive spectrographic unit was used to study in detail the Al2O3 oxide morphology and oxide-metal interface of a nickel-rich NiAl alloy (Ni-42 at% Al) with a view toward providing information relevant to spalling theories in the MCrAlY system. In addition, the kinetics of spalling was studied for critical evaluation of one of the step-process spall models and for collection of pertinent experimental data. Cyclic oxidation tests were run in 1-atm air at about 1100 C, and isothermal specimens were examined from 2 min to 200 hr of exposure. It is shown that oxide spalling occurs primarily at the oxide-metal interface in an intergranular mode, that crystallographic Kirkendall voids arise as a result of oxidation, and that the fractional area of spalled oxide varies widely in cyclic tests but increases with the square of oxide thickness for isothermal tests. A spall model is developed in the form of a summation series.

Smialek, J. L.↗
NASA NTRS1978

Final system instrumentation design package for Decade 80 solar house

The final configuration of the Decade 80 solar house to monitor and collect system performance data is presented. A review demonstrated by actual operation that the system and the data acquisition subsystem operated satisfactorily and installation of instrumentation was in accordance with the design. This design package is made up of (1) site and system description, (2) operating and control modes, and (3) instrumentation program (including sensor schematic).

Source record↗