Search NASA⌕ Search

SEARCH · Search NASA

Results for “Distillation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Corrosion fatigue of 2219-T87 aluminum alloy

Corrosion fatigue studies were conducted on bare, chemical conversion coated, and anodized 2219-T87 aluminum alloy. These tests were performed using a rotating beam machine running at a velocity of 2500 rpm. The corrosive environments tested were distilled water, 100 ppm NaCl, and 3.5 percent NaCl. Results were compared to the endurance limit in air. An evaluation of the effect of protective coatings on corrosion fatigue was made by comparing the fatigue properties of specimens with coatings to those without.

Mcmillan, V. C.↗
NASA NTRS1986

Determination of solid mass fraction in partially frozen hydrocarbon fuels

Filtration procedures alone are insufficient to determine the amounts of crystalline solid in a partially frozen hydrocarbon distillate fraction. This is due to the nature of the solidification process by which a large amount of liquid becomes entrapped within an interconnected crystalline structure. A technique has been developed to supplement filtration methods with an independent determination of the amount of liquid in the precipitate thereby revealing the actual value of mass percent crystalline solid, %S. A non-crystallizing dye is injected into the fuel and used as a tracer during the filtration. The relative concentrations of the dye in the filtrate and precipitate fractions is subsequently detected by a spectrophotometric comparison. The filtration apparatus was assembled so that the temperature of the sample is recorded immediately above the filter. Also, a second method of calculation has been established which allows significant reduction in test time while retaining acceptable accuracy of results. Data have been obtained for eight different kerosene range hydrocarbon fuels.

Cotterell, E. M.↗
NASA NTRS1985

A refractory inclusion in the Kaba CV3 chondrite - Some implications for the origin of spinel-rich objects in chondrites

The first detailed petrographic and mineralogical study of a Ca, Al-rich inclusion (CAI) from the Kaba CV3 chondrite is reported. This 'fine-grained' CAI contains abundant small, rounded, rimmed, spinel-rich objects which have important features in common with the spinel-rich objects in other carbonaceous and ordinary chondrites. These nodules are interpreted as fractionated distillation residues of primitive dust. However, the available data do not unambiguously rule out a condensation origin for at least some of these objects. Finally, the preservation of distinct diopside-hedenbergite rims on the spinel-rich bodies and the small grain size of many minerals in the CAI matrix material both suggest that the CAI accreted cool and had a relatively cool thermal history in the Kaba parent body.

Fegley, B., Jr.↗
NASA NTRS1985

Toward a spartan scenario for use of lunar materials

The present discussion has the objective to identify those raw materials for use in manufacture which can most readily be obtained from lunar materials as they are currently known. The state of lunar exploration is incomplete, and concentrated ores may exist for elements now regarded as rare or dispersed. This paper provides a description of minimum possibilities, based on the notion of making do with the least feasible amounts of separation and processing. The discussion is limited to the most abundant materials observed at lunar sites visited by the Apollo missions. The ground rules for use of lunar products are considered along with the tools required to carry out any significant production of raw materials for manufacture, and lunar surface conditions. Readily available materials include unprocessed regolith and minimally processed regolith. A few examples of processing methods are provided, giving attention to thermal release of gases, hydrogen reduction of ilmenite, carbonyl processing, electrolysis of molten silicate, and destructive distillation.

Haskin, L. A.↗
NASA NTRS1987

Clarification Procedure for Gels

Procedure developed to obtain transparent gels with consistencies suitable for crystal growth, by replacing sodium ions in silicate solution with potassium ions. Clarification process uses cation-exchange resin to replace sodium ions in stock solution with potassium ions, placed in 1M solution of soluble potassium salt. Slurry stirred for several hours to allow potassium ions to replace all other cations on resin. Supernatant solution decanted through filter, and beads rinsed with distilled water. Rinsing removes excess salt but leaves cation-exchange beads fully charged with potassium ions.

Barber, Patrick G.↗
NASA NTRS1987

G-300: The first French Getaway Special microgravity measurements of fluid thermal conductivity

Thermal conductivity measurements on liquids are difficult to perform on Earth because of thermal motions due to convection. In microgravity, the convection due to buoyancy is evanescent, and a strong reduction of Rayleigh and Nusselt numbers can be expected. Three low viscosity liquids are selected to carry out the measurements; distilled water (standard) and two silicone oils. A modified hot plate method with a simplified guard ring is used; the reduction of convective motions permitted the use in the experimental cells of larger interplate distances and/or temperature differences than in Earth measurements, improving the accuracy. Comparisons between Earth and orbit results may help to understand the convection occurrence in the cells. Thermal, vibrational, and EMI tests have proved that the design satisfies the NASA requirements.

Perron, J. C.↗
NASA NTRS1987

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in the SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗
NASA NTRS1987

Preparation of B-trichloroborazine

The present invention relates to a method of preparing B-trichloroborazine. Generally, the method includes the combination of gaseous boron trichloride in an anhydrous aprotic organic solvent followed by addition of excess gaseous ammonia at ambient temperature or below. The reaction mixture is heated to about 100 to 140 C followed by cooling, removal of the solid ammonium chloride at ambient temperature, distillation of the solvent under vacuum if necessary at a temperature of up to about 112 C, and recovery of the B-trichloroborazine. Solvents include toluene, benzene, xylene, chlorinated hydrocarbons, chlorinated aromatic compounds, or mixtures thereof. Toluene is a preferred solvent. The process provides a convenient synthesis of a material which often decomposes on standing. B-trichloroborazine is useful in a number of chemical reactions, and particularly in the formation of high temperature inorganic polymers and polymer precursors.

Riccitiello, Salvatore R.↗
NASA NTRS1987

Pre- and posttreatment techniques for spacecraft water recovery

The objective was to develop techniques for satisfactory pretreatment of waste water (urine and wash water) prior to recovery by distillation and satisfactory post-treatment of the recovered water and humidity condensate for purification to the high quality necessary for reuse. The effort included literature and laboratory investigations, feasibility evaluations of candidate approaches, and development of conceptual designs for a waste water pretreatment system and a recovered water post-treatment system.

Putnam, David F.↗
NASA NTRS1986

Plastic deformation of a magnesium oxide 001-plane surface produced by cavitation

An investigation was conducted to examine plastic deformation of a cleaved single-crystal magnesium oxide 001-plane surface exposed to cavitation. Cavitation damage experiments were carried out in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (2 mm) to the surface of the cleaved specimen. The dislocation-etch-pit patterns induced by cavitation were examined and compared with that of microhardness indentations. The results revealed that dislocation-etch-pit patterns around hardness indentations contain both screw and edge dislocations, while the etch-pit patterns on the surface exposed to cavitation contain only screw dislocations. During cavitation, deformation occurred in a thin surface layer, accompanied by work-hardening of the ceramic. The row of screw dislocations underwent a stable growth, which was analyzed crystallographically.

Hattori, S.↗
NASA NTRS1986

Interstellar fossil Mg-26 and its possible relationship to excess meteoritic Mg-26

A plausible scenario is advanced for explainig a linear correlation found in some solar system solids between their Mg-26/Mg-24 isotopic ratios and their Al/Mg elemental abundance ratios. This scenario involves three stages: (1) the mechanical aggregation of an average ensemble of Al-bearing dust particles that is postulated to be modestly enriched in the Al/Mg abundance ratio because the aggregated particles themselves are; (2) the extraction, perhaps but not necessarily by hot distillation, of almost all Mg, leaving an aggregate with a large Al/Mg ratio and a large Mg-26 excess; and (3) the uptake of normal ambient Mg by the resulting hot Al-rich solid as it cools in Mg-rich vapor. A linear correlation in solids between their Mg-26/Mg-24 isotopic ratio and their aluminum enrichment may be a fossil correlation inherited from interstellar dust.

Clayton, Donald D.↗
NASA NTRS1986

Pre- and post-treatment techniques for spacecraft water recovery

Distillation-based waste water pretreatment and recovered water posttreatment methods are proposed for the NASA Space Station. Laboratory investigation results are reported for two nonoxidizing urine pretreatment formulas (hexadecyl trimethyl ammonium bromide and Cu/Cr) which minimize the generation of volatile organics, thereby significantly reducing posttreatment requirements. Three posttreatment methods (multifiltration, reverse osmosis, and UV-assisted ozone oxidation) have been identified which appear promising for the removal of organic contaminants from recovered water.

Putnam, David F.↗
NASA NTRS1986

Integrated waste and water management system

The performance requirements of the NASA Space Station have prompted a reexamination of a previously developed integrated waste and water management system that used distillation and catalytic oxydation to purify waste water, and microbial digestion and incineration for waste solids disposal. This system successfully operated continuously for 206 days, for a 4-man equivalent load of urine, feces, wash water, condensate, and trash. Attention is given to synergisms that could be established with other life support systems, in the cases of thermal integration, design commonality, and novel technologies.

Murray, R. W.↗
NASA NTRS1986

Catalytic processes for space station waste conversion

Catalytic techniques for processing waste products onboard space vehicles were evaluated. The goal of the study was the conversion of waste to carbon, wash water, oxygen and nitrogen. However, the ultimate goal is conversion to plant nutrients and other materials useful in closure of an ecological life support system for extended planetary missions. The resulting process studied involves hydrolysis at 250 C and 600 psia to break down and compact cellulose material, distillation at 100 C to remove water, coking at 450 C and atmospheric pressure, and catalytic oxidation at 450 to 600 C and atmospheric pressure. Tests were conducted with a model waste to characterize the hydrolysis and coking processes. An oxidizer reactor was sized based on automotive catalytic conversion experience. Products obtained from the hydrolysis and coking steps included a solid residue, gases, water condensate streams, and a volatile coker oil. Based on the data obtained, sufficient component sizing was performed to make a preliminary comparison of the catalytic technique with oxidation for processing waste for a six-man spacecraft. Wet oxidation seems to be the preferred technique from the standpoint of both component simplicity and power consumption.

Schoonover, M. W.↗
NASA NTRS1986

Controlled Ecological Life Support Systems (CELSS) physiochemical waste management systems evaluation

Parametric data for six waste management subsystems considered for use on the Space Station are compared, i.e.: (1) dry incineration; (2) wet oxidation; (3) supercritical water oxidation; (4) vapor compression distillation; (5) thermoelectric integrated membrane evaporation system; and (6) vapor phase catalytic ammonia removal. The parameters selected for comparison are on-orbit weight and volume, resupply and return to Earth logistics, power consumption, and heat rejection. Trades studies are performed on subsystem parameters derived from the most recent literature. The Boeing Engineering Trade Study (BETS), an environmental control and life support system (ECLSS) trade study computer program developed by Boeing Aerospace Company, is used to properly size the subsystems under study. The six waste treatment subsystems modeled in this program are sized to process the wastes for a 90-day Space Station mission with an 8-person crew, and an emergency supply period of 28 days. The resulting subsystem parameters are compared not only on an individual subsystem level but also as part of an integrated ECLSS.

Oleson, M.↗
NASA NTRS1988

Engineering data compendium. Human perception and performance. User's guide

The concept underlying the Engineering Data Compendium was the product of a research and development program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design and military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from the existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by systems designers. The present four volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is the first volume, the User's Guide, containing a description of the program and instructions for its use.

Boff, Kenneth R.↗
NASA NTRS1988

Engineering Data Compendium. Human Perception and Performance, Volume 1

The concept underlying the Engineering Data Compendium was the product an R and D program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design of military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by system designers. The present four volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is Volume 1, which contains sections on Visual Acquisition of Information, Auditory Acquisition of Information, and Acquisition of Information by Other Senses.

Boff, Kenneth R.↗
NASA NTRS1988

Engineering Data Compendium. Human Perception and Performance, Volume 2

The concept underlying the Engineering Data Compendium was the product of a Research and Development program (Integrated Perceptual Information for Designers project) aimed at facilitating the application of basic research findings in human performance to the design of military crew systems. The principal objective was to develop a workable strategy for: (1) identifying and distilling information of potential value to system design from existing research literature, and (2) presenting this technical information in a way that would aid its accessibility, interpretability, and applicability by system designers. The present volumes of the Engineering Data Compendium represent the first implementation of this strategy. This is Volume 2, which contains sections on Information Storage and Retrieval, Spatial Awareness, Perceptual Organization, and Attention and Allocation of Resources.

Boff, Kenneth R.↗