Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Working Toward Nanotube Composites

One of the most attractive applications of single-wall carbon nanotubes (SWNT) is found in the area of structural materials. Nanotubes have a unique combination of high strength, modulus, and elongation to failure, and therefore have potential to significantly enhance the mechanical properties of today's composites. This is especially attractive for the aerospace industry looking for any chance to save weight. This is why NASA has chosen to tackle this difficult application of SWNT. Nanotube properties differ significantly from that of conventional carbon fibers, and a whole new set of problems, including adhesion and dispersion in the adhesive polymer matrix, must be resolved in order to engineer superior composite materials. From recent work on a variety of applications it is obvious that the wide range of research in nanotubes will lead to advances in physics, chemistry, and engineering. However, the possibility of ultralightweight structures is what causes dreamers to really get excited. One of the important issues in composite engineering is aspect ratio of the fibers, since it affects load transfer in composites. Nanotube length was a gray area for years, since they are formed in bundles, making it impossible to monitor individual nanotube length. Even though bundles are observed to be tens and hundreds of microns long, they can be built of relatively short tubes weakly bound by Van der Waals forces. Nanotube length can be affected by subsequent purification and ultrasound processing, which has been necessary in order to disperse nanotubes and introduce them into a polymer matrix. Some calculations show that nanotubes with 10(exp 5) aspect ratio may be necessary to achieve good load transfer. We show here that nanotubes produced in our laser system are as much as tens of microns long and get cut into lengths of hundreds of nanometers during ultrasound processing. Nanotube length was measured by AFM on pristine nanotube specimens as well, as after sonication. In each case great care was taken to measure individual nanotubes, rather than bundles. Pristine nanotubes were collected on quartz substrates placed directly in the laser oven and exposed for 0.5 s. This results in an equal mix of bundles and individual nanotubes. Nanotube length measurements were limited practically by the lateral span of the AFM scanner, but nanotube length is certainly in excess of 20 micrometers.

Arepalli, Sivaram↗
NASA NTRS2002

Measurements of Turbulent Flow Field in Separate Flow Nozzles with Enhanced Mixing Devices - Test Report

As part of the Advanced Subsonic Technology Program, a series of experiments was conducted at NASA Glenn Research Center on the effect of mixing enhancement devices on the aeroacoustic performance of separate flow nozzles. Initial acoustic evaluations of the devices showed that they reduced jet noise significantly, while creating very little thrust loss. The explanation for the improvement required that turbulence measurements, namely single point mean and RMS statistics and two-point spatial correlations, be made to determine the change in the turbulence caused by the mixing enhancement devices that lead to the noise reduction. These measurements were made in the summer of 2000 in a test program called Separate Nozzle Flow Test 2000 (SFNT2K) supported by the Aeropropulsion Research Program at NASA Glenn Research Center. Given the hot high-speed flows representative of a contemporary bypass ratio 5 turbofan engine, unsteady flow field measurements required the use of an optical measurement method. To achieve the spatial correlations, the Particle Image Velocimetry technique was employed, acquiring high-density velocity maps of the flows from which the required statistics could be derived. This was the first successful use of this technique for such flows, and shows the utility of this technique for future experimental programs. The extensive statistics obtained were likewise unique and give great insight into the turbulence which produces noise and how the turbulence can be modified to reduce jet noise.

Bridges, James↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: 1) a k-epsilon turbulence model computation on a 6.8 million point grid using wall functions, 2) a k-epsilon turbulence model computation on a 14 million point grid integrating to the wall, and 3) a k-omega turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-epsilon and k-omega computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-epsilon computations which extended from 70% to 100% span at the exit rating plane, whereas the k-omega computation had reversed flow from 95% to 100% span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-epsilon case resulted in an under-prediction in adiabatic efficiency of 8.3 points, whereas the k-omega case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: (1) a k-ε turbulence model computation on a 6.8 million point grid using wall functions, (2) a k-ε turbulence model computation on a 14 million point grid integrating to the wall, and (3) a k-ω turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-ε and k-ω computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-ε computations which extended from 70 to 100 percent span at the exit rating plane, whereas the k-ω computation had reversed flow from 95 to 100 percent span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-ε case resulted in an underprediction in adiabatic efficiency of 8.3 points, whereas the k-ω case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS2016

Further Development and Assessment of a Broadband Liner Optimization Process

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broader frequency range. Thus, improved broadband liner designs must account for these constraints and, where applicable, take advantage of advanced manufacturing techniques that have opened new possibilities for novel configurations. This work focuses on the use of an established broadband acoustic liner optimization process to design a variable-depth, multi-degree of freedom liner for a high speed fan. Specifically, in-duct attenuation predictions with a statistical source model are used to obtain optimum impedance spectra over the conditions of interest. The predicted optimum impedance information is then used with acoustic liner modeling tools to design a liner aimed at producing impedance spectra that most closely match the predicted optimum values. The multi-degree of freedom design is carried through design, fabrication, and testing. In-duct attenuation predictions compare well with measured data and the multi-degree of freedom liner is shown to outperform a more conventional liner over a range of flow conditions. These promising results provide further confidence in the design tool, as well as the enhancements made to the overall design process.

Nark, Douglas M.↗
NASA NTRS2019

Design and Acoustic Efficacy of a Broadband Liner for the Inlet of the DGEN Aero-Propulsion Research Turbofan

Advanced fan designs (including higher bypass ratios) and shorter engine nacelles have highlighted a need for increased fan noise reduction over a broader frequency range. With these observations in mind, an acoustic liner optimization process has been developed to achieve improved broadband liner designs. A series of advanced liner design studies at increasing technology readiness levels have been conducted as the overall optimization methodology has been enhanced. As part of the analysis, the overall design and evaluation capability was extended such that external observer locations may be included in the optimization process. This enhancement will provide a much wider design space in designing advanced broadband liners. In this work, further validation was pursued through the fabrication and testing of two liner designs for the NASA Glenn DGEN Aero-propulsion Research Turbofan (DART). The DART was used to document the efficacy of acoustic liners installed in the inlet of the DGEN380. An advanced Multi-Degree of Freedom Liner was designed, fabricated, and tested, along with a traditional Single-Degree-of-Freedom Liner, and those results compared to a hardwall baseline inlet. Farfield acoustic data were acquired from and external array, evaluated and reported herein terms of overall, broadband, and tonal components of the insertion loss. The predicted attenuation results generally matched expected trends of the measured data for the conditions considered.

Liners↗
NASA NTRS2018

Broadband Inlet Liner Design for the DGEN Aero-Propulsion Research Turbofan

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broad frequency range. With these observations in mind, an acoustic liner optimization process has been developed to achieve improved broadband liner designs. A series of advanced liner design studies at increasing technology readiness levels has been conducted as the overall optimization methodology has been enhanced. In this work, further validation was pursued through the fabrication and testing of two liner designs for the NASA Glenn DGEN Aero-propulsion Research Turbofan. Specifically, single and three layer liners were designed, fabricated, and tested. Analysis of the predicted attenuation results showed them to generally match expected trends for the conditions considered. The effects of source distribution on predicted directivity were also illustrated through the flexibility of a statistical source model. As part of the analysis, the overall design and evaluation capability was extended such that external observer locations may be included in the optimization process. This enhancement will provide a much wider design space for the development of advanced broadband liners. These preliminary results provide further confidence in the design tools and enhancements made to the overall liner design process.

Nark, Douglas M.↗
NASA NTRS2019

Design of an Advanced Inlet Liner for the Quiet Technology Demonstrator 3

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broad frequency range. Thus, improved broadband liner designs must account for these constraints and take advantage of novel liner configurations. With these observations in mind, the development and assessment of a broadband acoustic liner optimization process has been pursued through a series of design and experimental studies. In this work, an advanced inlet liner was designed for a Boeing 737MAX-7 to reduce drag and to improve the broadband noise reduction relative to conventional liners in use today. Specifically, a three layer liner was designed, fabricated, and flight tested as part of the Quiet Technology Demonstrator 3 flight test program. Initial tonal predictions captured the behavior of the measured data very well and both prediction and measurements show an increased acoustic benefit at larger observer angles, particularly at the takeoff condition. Ultimately, flight test results showed the three degree-of-freedom liner to provide a 3.2 EPNdB cumulative inlet component benefit and a 0.7 EPNdB cumulative airplane benefit over the production liner. This excellent result provides valuable validation of the broadband liner design process, as well as the enhancements made to the overall approach. It also illustrates the value of the design process in concurrently evaluating various liner designs (i.e., SDOF, MDOF, etc.) and their application to various locations. Thus, the design process may be applied with further confidence to investigate novel liner configurations in future design studies.

Nark, Douglas M.↗
NASA NTRSDate not supplied

Calibration of a V-Cone for Low Mass Flows For Small Core Compressor Research

Advancements in core compressor technologies are necessary for next generation, high Overall Pressure Ratio (OPR) turbofan engines. High pressure compressors (HPCs) for future engines are being designed with exit corrected mass flow rates less than 2.25 kg/s (5 lbm/s). In order to accurately measure the performance of these advanced designs, high accuracy measurements are needed in test facilities. The W7 High Speed Multistage Axial Compressor Facility at NASA Glenn Research Center has been used to acquire data for advanced compressor designs. This facility utilizes an advanced differential pressure flow meter called a V-Cone. The facility has historically tested components with physical mass flow rates in the range of 27 to 45 kg/s (60 to 100 lbm/s). As such, when the V-Cone was calibrated prior to installation, the calibrations focused on higher mass flow rates, and uncertainties in that regime range from 0.5% to 0.85%. However, for low mass flow rates under 9 kg/s (20 lbm/s), expected in tests of advanced high OPR HPCs rear stages, the uncertainties of the V-Cone exceed 2.5%. To address this, using a method similar to that utilized by the National Institute of Standards and Technology, an array of Critical Flow Venturi Nozzles (CFVs) was installed in the W7 test section and used to calibrate the V-Cone in 0.5 kg/s (1 lbm/s) increments up to 10.5 kg/s (23 lbm/s). This effort details the measurements and uncertainties associated with this calibration which resulted in a final uncertainty of the V-Cone measurements under 1%.

Measurement Uncertainty↗
NASA NTRS1980

Space shuttle main engine digital controller

The controller provides responsive control of engine thrust and mixture ratio through the digital computer in the controller, updating the instructions to the engine control elements 50 times per second (every 20 milliseconds). Additionally, precise engine performance is achieved through closed loop control, utilizing 16 bit computation, 10 bit input/output resolution, and self calibrating analog-to-digital conversion. Engine reliability is enhanced by a dual redundant control system that allows normal operation after the first failure and a fail-safe shutdown after a second failure. The digital computer is programmable, allowing modification of engine control equations and constants by change of the stored program (software). The controller is packaged in a sealed, pressurized chassis with cooling provided by convection heat transfer through pin fins as part of the main chassis. The electronics are distributed on functional modules having special provisions for thermal and vibrational protection.

Mitchell, W. T.↗
NASA NTRS1956

Effect of design over-all compressor pressure ratio division on acceleration characteristics of three hypothetical two-spool turbojet engines

The engines, each with a compressor overall total-pressure ratio of 12 and a design inner-turbine-inlet temperature of 2500 degrees R, were investigated at static sea-level conditions to determine the effect on transient performance of varying the desitn pressure ratio divisions 2-6, 3-4, and 4-3 between the outer and inner compressors. The transient considered was an acceleration from 40 to 100 percent design thrust. When the outer compressor of each engine reached design speed, the inner compressors were overspeeding, the maximum being only 1.7 over design mechanical speed. Acceleration times for the three engines were equal.

TURBINES - MATCHINE↗
NASA NTRS1986

How different a modern SST would be

The characteristics of a proposed SST are described. The proposed aircraft is to have two engines and an arrow-wing design, a passenger capacity of 250, and attain speeds of Mach 2.7. The low fineness ratio, low-aspect ratio wing planform, different engine nacelles location, and improved lift-to-drag ratio of the aircraft contribute to attaining an economical supersonic cruise. The proposed structural design and materials for the aircraft are examined; the material and design are to be applicable to high Mach and high temperature. Changes in the SST propulsion system, the nozzle designs, and landing and takeoff procedures to improve the operation of the aircraft are discussed.

Driver, C.↗
NASA NTRS2010

SSME Engine Controller Development and Evolution

The SSME engine controller is a redundant, micro-processor based control unit. The controller along with its embedded software provides closed loop control of the engine s thrust and mixture ratio during flight as well as configuring the engine state and operations during non-flight activities such as checkouts, and pre-start engine conditioning. It processes orbiter commands into engine actions and provides engine state and health information to the orbiter for immediate action, telemetry and recording. In addition the controller includes functions which continually monitor and manage engine health, and can activate a variety of fault mitigation actions to insure safe engine operation. The objective of this paper is to provide a description of the SSME engine controller as well as its developmental history and lessons learned

Abrams, Russ↗
NASA NTRS2017

Structural Design Exploration of an Electric Powered Multi-Propulsor Wing Configuration

Advancements in aircraft electric propulsion may enable an expanded operational envelope for electrically powered vehicles compared to their internal combustion engine counterparts. High aspect ratio wings provide additional lift and drag reduction for a proposed multi-propulsor design, however, the challenge is to reduce the weight of wing structures while maintaining adequate structural and aeroelastic margins. Design exploration using a conventional design-and-build philosophy coupled with a finite element method (FEM)-based design of experiments (DOE) strategy are presented to examine high aspect ratio wing structures that have spanwise distributed electric motors. Multiple leading-edge-mounted engine masses presented a challenge to design a wing within acceptable limits for dynamic and aeroelastic stability. Because the first four primary bending eigenmodes of the proposed wing structure are very sensitive to outboard motor placement, safety-of-flight requirements drove the need for multiple spars, rib attachments, and outboard structural reinforcements in the design. Global aeroelasticity became an increasingly important design constraint during the on-going design process, with outboard motor pod flutter ultimately becoming a primary design constraint. Designers successively generated models to examine stress, dynamics, and aeroelasticity concurrently. This research specifically addressed satisfying multi-disciplinary design criteria to generate fluid-structure interaction solution sets, and produced high aspect ratio primary structure designs for the NASA Scalable Convergent Electric Propulsion Technology and Operations Research (SCEPTOR) project in the Aeronautic Research Mission Directorate at NASA. In this paper, a dynamics-driven, quasi-inverse design methodology is presented to address aerodynamic performance goals and structural challenges encountered for the SCEPTOR demonstrator vehicle. These results are compared with a traditional computer aided design based approach.

Moore, James B.↗
NASA NTRS1947

Preliminary Investigation of Over-all Performance of Experimental Turbojet Engine for Guided Missiles

A preliminary investigation of the over-all performance of a simply constructed, short-life, turbojet engine was conducted. The unit was operated at a pressure altitude of 15,000 feet for ram-pressure ratios of 1.2 t o 1.8. The corrected engine speed was varied from the minimum for good combustion to about 17,000 rpm, which is approximately 75 percent of rated speed. The performance is given by generalized parameters that permit the calculation of performance at any altitude. The corrected net thrust of the turbojet engine increased with ram-pressure ratio for a given corrected engine speed above 14,500 rpm and reached a maximum of 425 pounds at a ram-pressure ratio of 1.8 and a corrected engine speed of 16,650 rpm, The corrected thrust specific fuel consumption decreased with flight speed for corrected engine speeds higher than 13,600 rpm, The minimum corrected thrust specific fuel consumption of 1.48 was obtained at a ram-pressure ratio of 1,8 and a corrected engine speed of 15,000 rpm. For all ram-pressure ratios, choking occurred in the engine for corrected engine speeds greater than 14,500 rpm.

Eustis, Robert H.↗
NASA NTRSDate not supplied

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗
NASA NTRSDate not supplied

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗