Search NASA⌕ Search

SEARCH · Search NASA

Results for “EXPULSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Design and testing of the Space Station Freedom Propellant Tank Assembly

Propellant storage and management functions for the Propulsion Module of the U.S. Space Station Freedom are provided by the Propellant Tank Assembly (PTA). The PTA consists of a surface-tension type propellant acquisition device contained within a welded titanium pressure vessel. The PTA design concept was selected with high reliability and low program risk as primary goals in order to meet stringent NASA structural, expulsion, fracture control and reliability requirements. The PTA design makes use of Shuttle Orbital Maneuvering System and Peacekeeper Propellant Storage Assembly design and analysis techniques. This paper summarizes the PTA design solution and discusses the underlying detailed analyses. In addition, design verification and qualification test activities are discussed.

Dudley, D. D.↗

Ordovician impacts at sea in Baltoscandia

Northern Europe has an assemblage of Ordovician probable impacts that is exceptional because the structures involved are relatively old yet well preserved because they formed at sea and because they formed within a restricted geological time in a relatively small area. The Tvaren, Kardla, and Lockne structures might not be strictly contemporaneous but all formed near the beginning of the Caradoc Age (about 460 Ma), whereas the Granby structure is about 20 Ma older. The range of diameters is from about 2 km (Tvaren, Granby) to 8 km (Lockne). The stratigraphic succession formed on impact at sea, as uniformly documented by these structures, begins with a breccia lens consisting of basement rocks that are intensely crushed. Owing to expulsion of sea water by the impact, this breccia formed under essentially dry conditions. Later on this breccia was in part hydrothermally altered. It is overlain by backsurge turbidite that formed from fragments of local sedimentary bedrock and crystalline basement when the sea water returned to the crater site. Either the turbidite is simply a Bouma sequence (although quite thick - as much as over 50 m) from very coarse rubble to mud, or it is more complex. After deposition of the backsurge turbidite, or turbidite complex, the craters still remained as 150-200-m-deep holes in the sea bed. Together with the presence of relatively shallow water over the rim wall, this situation created predictable hydrologic conditions for extended histories of sedimentation and biological development at the crater as well as within it. The presence of a concentration of craters within a limited area of well-preserved and accessible Ordovician deposits raises a question about the Ordovician, especially its middle portion, as potentially an age of relatively intense impact activity even in wider areas. In this connection it may be apposite to mention that the only fossil stony meteorites so far recorded in rocks are from the late Early and the Middle Ordovician.

Lindstroem, M.↗

Automated technologies needed to prevent radioactive materials from reentering the atmosphere

Project SIREN (Search, Intercept, Retrieve, Expulsion Nuclear) was created to identify and evaluate the technologies and operational strategies needed to rendezvous with and capture aerospace radioactive materials (e.g., a distressed or spent space reactor core) before such materials can reenter the terrestrial atmosphere and then to safely move these captured materials to an acceptable space destination for proper disposal. A major component of the current project SIREN effort is the development of an interactive technology model (including a computerized data base) that explores, in building-block fashion, the interaction of the technologies and procedures needed to successfully accomplish a SIREN mission. The SIREN model will include appropriate national and international technology elements--both contemporary and projected into the next century. To obtain maximum flexibility and use, the SIREN technology data base is being programmed for use on 286-class PC's. The major technical elements for a successful SIREN mission include: ground and space-based tracking, launch vehicles of needed payload capacity, telerobotic systems, sensors, capture technologies, and space transport and disposal. However, Project SIREN also will impose specialized requirements including the use of dextrous aerospace systems capable of properly functioning in intense radiation and thermal environments.

Buden, David↗

Automated technologies needed to prevent radioactive materials from reentering the atmosphere

Project SIREN (Search, Intercept, Retrieve, Expulsion Nuclear) has been created to identify and evaluate the technologies and operational strategies needed to rendezvous with and capture aerospace radioactive materials (e.g., a distressed or spent space reactor core) before such materials can reenter the terrestrial atmosphere and then to safely move these captured materials to an acceptable space destination for proper disposal. A major component of the current Project SIREN effort is the development of an interactive technology model (including a computerized data base) that explores in building block fashion the interaction of the technologies and procedures needed to successfully accomplish a SIREN mission. This SIREN model will include appropriate national and international technology elements-both contemporary and projected into the next century. To permit maximum flexibility and use, the SIREN technology data base is being programmed for use on 386-class PC's.

Buden, David↗

Gamma ray bursts from extragalactic sources

The properties of gamma ray bursts of classical type are found to be explicable in terms of high speed collisions between stars. A model is proposed in which the frequency of such collisions can be calculated. The model is then applied to the nuclei of galaxies in general on the basis that galaxies, or at least some fraction of them, originate in the expulsion of stars from creation centers. Evidence that low level activity of this kind is also taking place at the center of our own Galaxy is discussed. The implications for galactic evolution are discussed and a negative view of black holes is taken.

Hoyle, Fred↗

Enhancement of diffusive transport in oscillatory flows

The theory of transport of passive scalars in oscillatory flows is reexamined. The differences between transport in standing and traveling waves are emphasized. Both Lagrangian and Eulerian diffusivities are calculated, and the conditions for their applicability are discussed. Numerical simulations are conducted to understand the expulsion of gradients from time-dependent eddies and the resulting transport. The results indicate that it is the Eulerian diffusivity that is of primary relevance for describing enhanced transport on spatial scales larger than that of the eddies.

Knobloch, E.↗

Autogenous pressurization of cryogenic vessels using submerged vapor injection

Experimental results are reported for submerged injection pressurization and expulsion tests of a 4.89 cu m liquid hydrogen tank. The pressurant injector was positioned near the bottom of the test vessel to simulate liquid engulfment of the pressurant gas inlet, a condition that may occur in low-gravity conditions. Results indicate a substantial reduction in pressurization efficiency with pressurant gas requirements approximately five times greater than ideal amounts. Consequently, submerged vapor injection should be avoided as a low-gravity autogenous pressurization method whenever possible. The work presented herein validates that pressurant requirements are accurately predicted by a homogeneous thermodynamic model when the submerged injection technique is employed.

Stochl, Robert J.↗

Early phases of LMC star clusters?

On the basis of optical and IUE observations we have investigated the possibility that some of the very young stellar systems of the LMC, such as SL360, may be regarded as globular clusters at the very early phases of their dynamical evolution after the gas cloud expulsion.

Kontizas, Evangelos↗

The Magellan aerobraking experiment - Attitude control simulation and preliminary flight results

On May 25, 1993 the Magellan spacecraft began an experiment on 'aerobraking', or use of aerodynamic drag from the Venusian atmosphere to provide deceleration. The Magellan spacecraft will strive to transition from a highly elliptical orbit into a near-circular orbit in approximately 70 days by successively dipping into the atmosphere to gain the necessary reduction in orbital velocity. Magellan will be the first three-axis stabilized spacecraft to perform this type of multipass aerobraking, and will also be attempting to achieve the largest velocity reduction to date, all with a spacecraft that was not designed for this application. This paper addresses redesign of the attitude control system onboard Magellan for use during aerobraking. The dynamics and control of the spacecraft were simulated, and these results are presented and summarized. Modifications necessary to the existing flight control system and, specifically, to the mass expulsion control scheme are discussed. Changes were minimized though, due to the low-cost, high-risk approach to Magellan's aerobraking experiment. Some initial flight results from the first week of aerobraking operations will be highlighted.

Carpenter, Anita S.↗

Opposed Bellows Would Expel Contents Of Tank

Proposed storage tank contains two pairs of opposed bellows used to expel its contents. Storage and expulsion volumes of tank same as those of older version of tank equipped with single bellows. Four bellows offer greater stability. Applications include automobile cooling systems and gasoline-powered tools like chain saws and leaf blowers.

Whitaker, Willie↗

Detection of emetic activity in the cat by monitoring venous pressure and audio signals

To investigate the use of audio signals as a simple, noninvasive measure of emetic activity, the relationship between the somatic events and sounds associated with retching and vomiting was studied. Thoracic venous pressure obtained from an implanted external jugular catheter was shown to provide a precise measure of the somatic events associated with retching and vomiting. Changes in thoracic venous pressure monitored through an indwelling external jugular catheter with audio signals, obtained from a microphone located above the animal in a test chamber, were compared. In addition, two independent observers visually monitored emetic episodes. Retching and vomiting were induced by injection of xylazine (0.66mg/kg s.c.), or by motion. A unique audio signal at a frequency of approximately 250 Hz is produced at the time of the negative thoracic venous pressure change associated with retching. Sounds with higher frequencies (around 2500 Hz) occur in conjunction with the positive pressure changes associated with vomiting. These specific signals could be discriminated reliably by individuals reviewing the audio recordings of the sessions. Retching and those emetic episodes associated with positive venous pressure changes were detected accurately by audio monitoring, with 90 percent of retches and 100 percent of emetic episodes correctly identified. Retching was detected more accurately (p is less than .05) by audio monitoring than by direct visual observation. However, with visual observation a few incidents in which stomach contents were expelled in the absence of positive pressure changes or detectable sounds were identified. These data suggest that in emetic situations, the expulsion of stomach contents may be accomplished by more than one neuromuscular system and that audio signals can be used to detect emetic episodes associated with thoracic venous pressure changes.

A Nagahara↗

Thermodynamic models for bounding pressurant mass requirements of cryogenic tanks

Thermodynamic models have been formulated to predict lower and upper bounds for the mass of pressurant gas required to pressurize a cryogenic tank and then expel liquid from the tank. Limiting conditions are based on either thermal equilibrium or zero energy exchange between the pressurant gas and initial tank contents. The models are independent of gravity level and allow specification of autogenous or non-condensible pressurants. Partial liquid fill levels may be specified for initial and final conditions. Model predictions are shown to successfully bound results from limited normal-gravity tests with condensable and non-condensable pressurant gases. Representative maximum collapse factor maps are presented for liquid hydrogen to show the effects of initial and final fill level on the range of pressurant gas requirements. Maximum collapse factors occur for partial expulsions with large final liquid fill fractions.

Vandresar, Neil T.↗

Thermal and hydraulic considerations regarding the fate of water discharged by the outflow channels to the Martian northern plains

The identification of possible shorelines in the Martian northern plains suggests that the water discharged by the circum-Chryse outflow channels may have led to the formation of transient seas, or possibly even an ocean, covering as much as one-third of the planet. Speculations regarding the possible fate of this water have included local ponding and reinfiltration into the crust; freezing, sublimation, and eventual cold-trapping at higher latitudes; or the in situ survival of this now frozen water to the present day -- perhaps aided by burial beneath a protective cover of eolian sediment or lavas. Although neither cold-trapping at higher latitudes nor the subsequent freezing and burial of flood waters can be ruled out, thermal and hydraulic considerations effectively eliminate the possibility that any significant reassimilation of this water by local infiltration has occurred given climatic conditions resembling those of today. The arguments against the local infiltration of flood water into the northern plains are two-fold. First, given the climatic and geothermal conditions that are thought to have prevailed on Mars during the Late Hesperian (the period of peak outflow channel activity in the northern plains), the thickness of the cryosphere in Chryse Planitia is likely to have exceeded 1 km. A necessary precondition for the widespread occurrence of groundwater is that the thermodynamic sink represented by the cryosphere must already be saturated with ice. For this reason, the ice-saturated cryosphere acts as an impermeable barrier that effectively precludes the local resupply of subpermafrost groundwater by the infiltration of water discharged to the surface by catastraphic floods. Note that the problem of local infiltration is not significantly improved even if the cryosphere were initially dry, for as water attempts to infiltrate the cold, dry crust, it will quickly freeze, creating a seal that prevents any further infiltration from the ponded water above. The second argument against the local infiltration of flood water in the northern plains is based on hydraulic considerations. Repeated impacts have likely brecciated the Martian crust down to a depth of roughly 10 km. Given a value of permeability no greater than that inferred for the top 10 km of the Earth's crust (approximately 10(exp -2) darcies), a timescale as much as a billion years or more for the Martian groundwater system to achieve hydrostatic equilibrium, and the approximately 2-4 km elevation difference between the outflow channel source regions and the northern plains, the water confined beneath the frozen crust of the northern plains should have been under a significant hydraulic head. Thus, the existence of a hydraulic pathway between the ponded flood waters above the northern plains and the confined aquifer lying beneath it would not have led to the infiltration of flood water back into the crust, but rather the additional expulsion of groundwater onto the surface.

Clifford, S. M.↗

Experimental Results of Hydrogen Slosh in a 62 Cubic Foot (1750 Liter) Tank

Extensive slosh testing with liquid and slush hydrogen was conducted in a 62 cubic foot spherical tank to characterize the thermodynamic response of the system under normal gravity conditions. Slosh frequency and amplitude, pressurant type, ramp pressure, and ullage volume were parametrically varied to assess the effect of each of these parameters on the tank pressure and fluid/wall temperatures. A total of 91 liquid hydrogen and 62 slush hydrogen slosh tests were completed. Both closed tank tests and expulsions during sloshing were performed. This report presents and discusses highlights of the liquid hydrogen closed tank results in detail and introduces some general trends for the slush hydrogen tests. Summary comparisons between liquid and slush hydrogen slosh results are also presented.

Moran, Matthew E.↗

Slush Hydrogen Technology Program

A slush hydrogen (SH2) technology facility (STF) was designed, fabricated, and assembled by a contractor team of McDonnell Douglas Aerospace (MDA), Martin Marietta Aerospace Group (MMAG), and Air Products and Chemicals, Inc. (APCI). The STF consists of a slush generator which uses the freeze-thaw production process, a vacuum subsystem, a test tank which simulates the NASP vehicle, a triple point hydrogen receiver tank, a transfer subsystem, a sample bottle, a pressurization system, and a complete instrumentation and control subsystem. The STF was fabricated, checked-out, and made ready for testing under this contract. The actual SH2 testing was performed under the NASP consortium following NASP teaming. Pre-STF testing verified SH2 production methods, validated special SH2 instrumentation, and performed limited SH2 pressurization and expulsion tests which demonstrated the need for gaseous helium pre-pressurized of SH2 to control pressure collapse. The STF represents cutting-edge technology development by an effective Government-Industry team under very tight cost and schedule constraints.

Cady, Edwin C.↗

Feasibility study for a Cryogenic On-Orbit Liquid Depot-Storage, Acquisition and Transfer (COLD-SAT) satellite

This feasibility study presents the conceptual design of a spacecraft for performing a series of cryogenic fluid management flight experiments. This spacecraft, the Cryogenic On-Orbit Liquid Depot-Storage, Acquisition, and Transfer (COLD-SAT) satellite, will use liquid hydrogen as the test fluid, be launched on a Delta expendable launch vehicle, and conduct a series of experiments over a two to three month period. These experiments will investigate the physics of subcritical cryogens in the low gravity space environment to characterize their behavior and to correlate the data with analytical and numerical models of in-space cryogenic fluid management systems. Primary technologies addressed by COLD-SAT are: (1) pressure control; (2) chilldown; (3) no-vent fill; (4) liquid acquisition device fill; (5) pressurization; (6) low-g fill and drain; (7) liquid acquisition device expulsion; (8) line chilldown; (9) thermodynamic state control; and (10) fluid dumping.

Rybak, S. C.↗

Feasibility study for the Cryogenic Orbital Nitrogen Experiment (CONE)

An improved understanding of low gravity subcritical cryogenic fluid behavior is critical for the continued development of space based systems. Although early experimental programs provided some fundamental understanding of zero gravity cryogenic fluid behavior, more extensive flight data are required to design space based cryogenic liquid storage and transfer systems with confidence. As NASA's mission concepts evolve, the demand for optimized in-space cryogenic systems is increasing. Cryogenic Orbital Nitrogen Experiment (CONE) is an attached shuttle payload experiment designed to address major technological issues associated with on-orbit storage and supply of cryogenic liquids. During its 7 day mission, CONE will conduct experiments and technology demonstrations in active and passive pressure control, stratification and mixing, liquid delivery and expulsion efficiency, and pressurant bottle recharge. These experiments, conducted with liquid nitrogen as the test fluid, will substantially extend the existing low gravity fluid data base and will provide future system designers with vital performance data from an orbital environment.

Bell, R. S.↗

Prediction of pressurant mass requirements for axisymmetric liquid hydrogen tanks

Experimental data from several test series are compared to an existing correlation that predicts the amount of pressurant gas mass required to expel liquid hydrogen from axisymmetric tanks. It was necessary to use an alternate definition of the tank equivalent diameter to accommodate thermal mass in the tank wall that is initially warm and to accommodate liquid residuals in the tank after expulsion is stopped. With this modification, the existing correlation predicted mass requirements to within 14 percent of experimental results. Revision of the correlation constants using a nonlinear least-squares fit of the current experimental data has a minor effect, thus supporting the validity of the original correlation's form, its fitted constants, and the alternate definition of the tank equivalent diameter.

Vandresar, N. T.↗