Search NASA⌕ Search

SEARCH · Search NASA

Results for “FASTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Comprehensive magnetohydrodynamic hybrid simulations of Alfvén eigenmode bursts and fast-ion losses in the Large Helical Device

Comprehensive magnetohydrodynamic (MHD) hybrid simulations with neutral beam injection and collisions were conducted to investigate the Alfvén eigenmode (AE) bursts and the fast-ion losses in the large helical device (LHD) for the realistic conditions close to the experiments. In this study, it is found in the simulation of the slowing-down time scale that the AE bursts take place repetitively accompanied by fast-ion redistribution and losses leading to lower saturation levels of stored fast-ion energy than those in a classical calculation where the MHD perturbations are neglected. The fast-ion loss rate caused by the AE burst has the quadratic dependence on AE amplitude, which was observed in the LHD experiment. The majority of the lost fast ions are counter-passing particles whose velocity and pitch-angle are close to those of the beam injection. The second component of the lost fast ions is transit particles whose velocity is close to thermal velocity. The loss of the counter-passing particles occurs mainly during the AE bursts, while the transit particles are lost both during the AE bursts and the quiescent periods with larger loss rate than that in the classical calculation. The initial location of the lost counter-injected particles spreads from the plasma edge to the plasma center, while only the particles initially located in the peripheral region are lost for the co-injected beam.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical studies on saturated kink and sawtooth induced fast ion transport in JET ITER-like plasmas

Here, this presentation examines the energetic particle transport induced by saturated kink modes and sawtooth crashes in JET deuterium plasmas. It is known that kink mode-resonant transport and phase-space redistribution from sawtooth crashes can drive strong fast ion transport with dependencies on particle pitch and energy. Measurements with JET's Faraday cup fast ion loss detector array have shown that the internal kink growth phase preceding sawtooth crashes produces substantial fast ion losses. This report will numerically investigate the dominant energetic particle transport mechanism with a detailed examination of the fast ion phase-space dependencies, resonances, orbit topology changes, induced losses, and redistribution associated with the long-lived, resonant, kink mode and non-resonant sawtooth crash. The ORBIT-kick model forms the basis of the transport studies with realistic fast ion distributions produced from TRANSP. A recently created reduced model for sawtooth induced transport is used while the saturated kink modes are modeled with ideal MHD codes. The simulations were further validated against experiment with a newly developed synthetic Faraday cup fast ion loss detector in addition to scintillator probe and neutron measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of Pressure on Fast Picosecond Relaxation in Glass-Forming Materials

Understanding the microscopic mechanism of the fast dynamics (gigahertz-terahertz frequency range) in amorphous materials remains a challenge. Disordered systems usually exhibit two additional contributions in this frequency range in comparison to their crystalline counterparts: a low-frequency excess vibrations, the so-called boson peak, and the fast picosecond relaxation that appears as a quasielastic scattering (QES) in the light- and neutron-scattering spectra. The nature of both contributions remains a subject of active discussions. In particular, QES intensity varies significantly with temperature. These variations might be caused by pure thermal effect and/or by change in density. To separate these two contributions we performed detailed light (Raman and Brillouin) scattering studies of the fast dynamics at different experimental conditions: isothermal, isobaric, isokinetic, and isochoric. The analysis demonstrates that the volume contribution dominates the fast relaxation behavior in a liquid state while the thermal energy becomes more important in the glassy state. Moreover, the presented analysis of the light-scattering data reveals significant difference in sensitivity of the fast dynamics to pressure among seven glass-forming materials (van der Waals-bonding and hydrogen-bonding molecular systems and polymers) studied in this work. It appears that the fast dynamics in orthoterphenyl and glycerol depends on pressure (density) significantly weaker than in other materials. However, the earlier observed correlations between pressure-induced variations in the QES and boson peak intensities and between the boson peak frequency and intensity are confirmed for all the studied materials. The obtained experimental results are compared to predictions of different models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Fast IMRT with narrow high energy scanned photon beams

Purpose: Since the first publications on intensity modulated radiation therapy (IMRT) in the early 1980s almost all efforts have been focused on fairly time consuming dynamic or segmental multileaf collimation. With narrow fast scanned photon beams, the flexibility and accuracy in beam shaping increases, not least in combination with fast penumbra trimming multileaf collimators. Previously, experiments have been performed with full range targets, generating a broad bremsstrahlung beam, in combination with multileaf collimators or material compensators. In the present publication, the first measurements with fast narrow high energy (50 MV) scanned photon beams are presented indicating an interesting performance increase even though some of the hardware used were suboptimal. Methods: Inverse therapy planning was used to calculate optimal scanning patterns to generate dose distributions with interesting properties for fast IMRT. To fully utilize the dose distributional advantages with scanned beams, it is necessary to use narrow high energy beams from a thin bremsstrahlung target and a powerful purging magnet capable of deflecting the transmitted electron beam away from the generated photons onto a dedicated electron collector. During the present measurements the scanning system, purging magnet, and electron collimator in the treatment head of the MM50 racetrack accelerator was used with 3-6 mm thick bremsstrahlung targets of beryllium. The dose distributions were measured with diodes in water and with EDR2 film in PMMA. Monte Carlo simulations with geant4 were used to study the influence of the electrons transmitted through the target on the photon pencil beam kernel. Results: The full width at half-maximum (FWHM) of the scanned photon beam was 34 mm measured at isocenter, below 9.5 cm of water, 1 m from the 3 mm Be bremsstrahlung target. To generate a homogeneous dose distribution in a 10 x 10 cm{sup 2} field, the authors used a spot matrix of 100 equal intensity beam spots resulting in a uniformity of collimated 80%-20% penumbra of 9 mm at a primary electron energy of 50 MeV. For the more complex cardioid shaped dose distribution, they used 270 spots, which at a pulse repetition frequency of 200 Hz is completed every 1.36 s. Conclusions: The present measurements indicate that the use of narrow scanned photon beams is a flexible and fast method to deliver advanced intensity modulated beams. Fast scanned photon IMRT should, therefore, be a very interesting modality in the delivery of biologically optimized radiation therapy with the possibility for in vivo treatment verification with PET-CT imaging.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

A Strongly Fluorescing Anaerobic Reporter and Protein-Tagging System for Clostridium Organisms Based on the Fluorescence-Activating and Absorption-Shifting Tag Protein (FAST)

Visualizing protein localization and characterizing gene expression activity in live Clostridium cells is limited for lack of a real-time, highly fluorescent, oxygen-independent reporter system. Enzymatic reporter systems have been used successfully for many years with Clostridium spp.; however, these assays do not allow for real-time analysis of gene expression activity with flow cytometry or for visualizing protein localization through fusion proteins. Commonly used fluorescent reporter proteins require oxygen for chromophore maturation and cannot be used for most strictly anaerobic Clostridium organisms. Here we show that the fluorescence-activating and absorption-shifting tag protein (FAST), when associated with the fluorogenic ligand 4-hydroxy-3-methylbenzylidene-rhodanine (HMBR; now commercially available) and other commercially available ligands, is highly fluorescent in Clostridium acetobutylicum under anaerobic conditions. Using flow cytometry and a fluorescence microplate reader, we demonstrated FAST as a reporter system by employing the promoters of the C. acetobutylicum thiolase (thl), acetoacetate decarboxylase (adc), and phosphotransbutyrylase (ptb) metabolic genes, as well as a mutant P thl and modified ribosome binding site (RBS) versions of P adc and P ptb . Flow cytometry-based sorting was efficient and fast in sorting FAST-expressing cells, and positively and negatively sorted cells could be effectively recultured. FAST was also used to tag and examine protein localization of the predicted cell division FtsZ partner protein, ZapA, to visualize the divisome localization in live C. acetobutylicum cells. Our findings suggest that FAST can be used to further investigate Clostridium divisomes and more broadly the localization and expression levels of other proteins in Clostridium organisms, thus enabling cell biology studies with these organisms.

59 BASIC BIOLOGICAL SCIENCES↗

Fast Reactor Physics Model Verification Studies using ARC and PyARC Workflows

PyARC was recently developed at Argonne National Laboratory to automate many of the tasks required in the ARC (Argonne Reactor Computation) fast reactor simulation workflow, from input file generation, code execution, data transfer between ARC codes, and output postprocessing. PyARC will likely be the path forward to train new users of the ARC codes with the goal of wide adoption by the national laboratories, academia, and industry. In particular, for the ANL-JAEA collaboration under the Civil Nuclear Working Group (CNWG) project agreement NE-01, PyARC will be used to model the Joyo and EBR-II reactors for comparisons with measured data and calculated results from JAEA (Task 3: Fast Reactor Fuel and Core). As an additional avenue for verification and validation, this report investigates the use of PyARC towards a variety of existing ARC-based reactor models, in order to understand its efficacy in replicating the behavior of base ARC codes and better understand any limitations within modeling realistic fast reactor problems. To this end, PyARC was used to model the Joyo MKI, RBEC Benchmark-M, PRISM Mod-B, and EBR-II Run 138B cores, and its results were compared to those from existing ARC-based models. It was found that for hexagonal-based geometries PyARC was able to replicate the behavior of ARC codes to within 10 pcm for small reactor cores, and ~150pcm difference in eigenvalue for larger cores. These discrepancies are attributed primarily to differences in local mesh refinement options between ARC and PyARC, which currently cannot be resolved with PyARC’s latest version (1.6.0). In some of these cases, PyARC was used to model steady-state problems with initial core compositions originating from a prior REBUS depletion calculation. While PyARC was not designed to support such steady-state calculations, workarounds were applied to replicate the behavior of ARC-based calculations as closely as possible. Thus, these results demonstrate the wide extent to which they can be applied to fast reactor problems while still providing immense benefit to the user in terms of automating and standardizing common routines within the fast reactor analysis workflow. This study concluded that PyARC will be suitable for modeling the steady-state conditions of the EBR-II and Joyo fast reactors as part of the CNWG project agreement.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

FAST-1.1: A Computer Code for Thermal-Mechanical Nuclear Fuel Analysis under Steady-state and Transients (Developed under NQA-1-2017)

Fuel Analysis under Steady-state and Transients (FAST) is the U.S. Nuclear Regulatory Commission (NRC)’s computer code that calculates the steady-state and transient response of nuclear reactor fuel rods during long-term in-reactor burnup, anticipated operational occurrences (AOOs), design basis accidents (DBAs), and dry storage conditions. The code calculates the temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: * heat conduction through the fuel and other materials * heat transfer from the cladding-to-coolant * cladding elastic and plastic deformation, including creep * fuel-cladding mechanical interaction * fission gas release from the fuel * rod internal pressure and void volume * cladding oxidation The code contains necessary material and coolant properties, as well as clad-to-coolant heat transfer correlations, for normal operation through postulated accidents and AOOs for today’s U.S.-based light water reactor (LWR) fuel designs. FAST-1.1 also contains preliminary materials and models for new LWR fuel concepts, such as accident tolerant fuel (ATF), and non-LWR fuel concepts such as metallic fuels for sodium fast reactors (SFRs). FAST has been developed for use on Windows and Linux operating systems. This document describes FAST-1.1 and is one of a series of documents on the code; the other documents detail the material properties used by FAST as well as its integral assessment to experiments and commercial data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measured Thermal and Fast Neutrons Fluence Rates for ATF-1 Holders During ATR Cycle 166B

This report contains the thermal (2200 m/s) and fast (E>lMeV) neutron fluence rate data for the ATF-1 holders located in core for ATR Cycle 166B which were measured by the Radiation Measurements Laboratory (RML) as requested by the Power Reactor Programs (ATR Experiments) Radiation Measurements Work Order. This report contains measurements of the fluence rates corresponding to the particular elevations relative to the 80-ft. core elevation. The data in this report consist of (1) a table of the ATR power history and distribution, (2) a hard copy listing of all thermal and fast neutron fluence rates, and (3) plots of both the thermal and fast neutron fluence rates. All "BR" holder monitor wires for this cycle are 56.375 inches long. This length allows measurements from 31.17 inches above core midplane to 19.81 inches below core midplane. The distance from the end of the wires to the first count position was 4.25 inches for all wires counted from this cycle. The monitors were located in an outward small I-holes,1-22 and 1-23. Thermal neutron fluence was determined based on the activation of the CoAl wires and resonance corrections determined in the irradiation of Cycle 152A when the RML measured cadmium-covered as well as bare neutron monitors in the Southwest, Southeast, and H positions at the Center lobe to determine the division in neutron energy between epithermal and thermal neutrons. For more information please refer to letter “Radiation Measurements Laboratory measurements of in core ATR physics testing during cycle 152A. The measured values documented in RML procedure, “ACMM-3600, Flux Monitoring,” will be used indefinitely until further measurements supersede the current values. Fast neutron fluence was determined using the activation of nickel wires. Typically, a fission spectrum averaged cross section (E>1 MeV) is used as determined in detailed measurements described in “ATR Neutron Spectral Characterization,” which gives an effective cross section of 97 mb for the small I-holes. However, those measurements were performed with unfueled experiments. The fast fluence values reported here use a perturbed 114 mb effective>1 MeV spectrum averaged cross section for the small I-holes based on MCNP simulations for a previous fueled experiment in the1-24 position. Refer to “LWR- ATR Irradiation Measured Thermal and Fast Neutron Fluence Rates ATR CYCLE 133A 04/19/04 thru 05/17/04” for more information.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Safeguards Facility Model for Lead-cooled and Gas-cooled Fast Reactors

Efforts have been underway for many years on the development of safeguards for fast neutron reactors. The efforts have been primarily for sodium-cooled fast reactors (SFRs) in cooperation with Japan, to properly implement these safeguards as the reactors are conceptualized and ultimately commercialized. The primary challenge to development of adequate safeguard approaches for fast reactors has been in understanding how to apply different aspects of safeguards when facilities widely vary from one type of fast reactor to another and is largely dependent on several key aspects of the specific reactor type. For this report, the following key areas were identified for further analysis to determine where Lead-cooled Fast Reactors (LFRs) and Gas-Cooled Fast Reactors (GCFR) fuel material flow and key measurement points would differ from previously studied SFR safeguards.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

THE WIND OF ROTATING B SUPERGIANTS. I. DOMAINS OF SLOW AND FAST SOLUTION REGIMES

In the scenario of rotating radiation-driven wind theory for massive stars, three types of stationary hydrodynamic solutions are currently known: the classical ( fast ) m-CAK solution, the Ω- slow solution that arises for fast rotators, and the so-called δ - slow solution if high values of the δ line-force parameter are allowed independently of the rotation speed. Compared to the fast solution, both “ slow solutions” have lower terminal velocities. As the study of the parameter domain for the slow solution is still incomplete, we perform a comprehensive analysis of the distinctive flow regimes for B supergiants that emerge from a fine grid of rotation values, Ω, and various ionization conditions in the wind ( δ ) parameter. The wind ionization defines two domains: one for fast outflowing winds and the other for slow expanding flows. Both domains are clear-cut by a gap, where a kink/plateau structure of the velocity law could exist for a finite interval of δ . The location and width of the gap depend on T {sub eff} and Ω. There is a smooth and continuous transition between the Ω- slow and δ - slow regimes, a single Ω δ - slow regime. We discuss different situations where the slow solutions can be found and the possibility of a switch between fast and slow solutions in B supergiant winds. We compare the theoretical terminal velocity with observations of B and A supergiants and find that the fast regime prevails mostly for early B supergiants while the slow wind regime matches better for A and B mid- and late-type supergiants.

79 ASTRONOMY AND ASTROPHYSICS↗

Numerical Study of Erosion, Heating, and Acceleration of the Magnetic Cloud as Impacted by Fast Shock

The impact of an overtaking fast shock on a magnetic cloud (MC) is a pivotal process in CME–CME (CME: coronal mass ejection) interactions and CME–SIR (SIR: stream interaction region) interactions. MC with a strong and rotating magnetic field is usually deemed a crucial part of CMEs. To study the impact of a fast shock on an MC, we perform a 2.5 dimensional numerical magnetohydrodynamic simulation. Two cases are run in this study: without and with impact by fast shock. In the former case, the MC expands gradually from its initial state and drives a relatively slow magnetic reconnection with the ambient magnetic field. Analyses of forces near the core of the MC as a whole body indicates that the solar gravity is quite small compared to the Lorentz force and the pressure gradient force. In the second run, a fast shock propagates, relative to the background plasma, at a speed twice that of the perpendicular fast magnetosonic speed, catches up with and takes over the MC. Due to the penetration of the fast shock, the MC is highly compressed and heated, with the temperature growth rate enhanced by a factor of about 10 and the velocity increased to about half of the shock speed. The magnetic reconnection with ambient magnetic field is also sped up by a factor of two to four in reconnection rate as a result of the enhanced density of the current sheet, which is squeezed by the forward motion of the shocked MC.

79 ASTRONOMY AND ASTROPHYSICS↗

Fast-shock formation in line-tied magnetic reconnection models of solar flares

In a previous study by the author, an approximately stationary fast shock was tentatively identified in a numerical experiment designed to study line-tied magnetic reconnection. Here the evidence for the occurrence of a stationary fast shock is reexamined, and the previous identification is confirmed. In the numerical experiment, line-tied reconnection is modeled by a configuration which produces two supermagnetosonic outflow jets - one directed upward, away from the photosphere, and one directed downward, toward an arcade of closed magnetic loops tied to the photosphere. The fast shock occurs when the downward-directed jet encounters the obstacle formed by the closed loops. Although the existence of a stationary, or nearly stationary, fast shock is confirmed, the transition from the supermagnetosonic flow region upstream of the shock to the nearly static region downstream of the shock is more complicated than was previously thought. Immediately downstream of the shock, there exists a deflection sheath in which the submagnetosonic flow coming out of the shock is diverted around the region of static closed loops. The MHD jump conditions are used to investigate the characteristics of the fast shock and to show that a stationary shock cannot exist unless accompanied by a deflection sheath. Analysis of the shock's location and dimensions suggests that such fast shocks may contribute to particle acceleration and to thermal condensation in flares.

Forbes, T. G.↗

Scientific Visualization Using the Flow Analysis Software Toolkit (FAST)

Over the past few years the Flow Analysis Software Toolkit (FAST) has matured into a useful tool for visualizing and analyzing scientific data on high-performance graphics workstations. Originally designed for visualizing the results of fluid dynamics research, FAST has demonstrated its flexibility by being used in several other areas of scientific research. These research areas include earth and space sciences, acid rain and ozone modelling, and automotive design, just to name a few. This paper describes the current status of FAST, including the basic concepts, architecture, existing functionality and features, and some of the known applications for which FAST is being used. A few of the applications, by both NASA and non-NASA agencies, are outlined in more detail. Described in the Outlines are the goals of each visualization project, the techniques or 'tricks' used lo produce the desired results, and custom modifications to FAST, if any, done to further enhance the analysis. Some of the future directions for FAST are also described.

Bancroft, Gordon V.↗

The Processing of Airspace Concept Evaluations Using FASTE-CNS as a Pre- or Post-Simulation CNS Analysis Tool

As NASA speculates on and explores the future of aviation, the technological and physical aspects of our environment increasing become hurdles that must be overcome for success. Research into methods for overcoming some of these selected hurdles have been purposed by several NASA research partners as concepts. The task of establishing a common evaluation environment was placed on NASA's Virtual Airspace Simulation Technologies (VAST) project (sub-project of VAMS), and they responded with the development of the Airspace Concept Evaluation System (ACES). As one examines the ACES environment from a communication, navigation or surveillance (CNS) perspective, the simulation parameters are built with assumed perfection in the transactions associated with CNS. To truly evaluate these concepts in a realistic sense, the contributions/effects of CNS must be part of the ACES. NASA Glenn Research Center (GRC) has supported the Virtual Airspace Modeling and Simulation (VAMS) project through the continued development of CNS models and analysis capabilities which supports the ACES environment. NASA GRC initiated the development a communications traffic loading analysis tool, called the Future Aeronautical Sub-network Traffic Emulator for Communications, Navigation and Surveillance (FASTE-CNS), as part of this support. This tool allows for forecasting of communications load with the understanding that, there is no single, common source for loading models used to evaluate the existing and planned communications channels; and that, consensus and accuracy in the traffic load models is a very important input to the decisions being made on the acceptability of communication techniques used to fulfill the aeronautical requirements. Leveraging off the existing capabilities of the FASTE-CNS tool, GRC has called for FASTE-CNS to have the functionality to pre- and post-process the simulation runs of ACES to report on instances when traffic density, frequency congestion or aircraft spacing/distance violations have occurred. The integration of these functions require that the CNS models used to characterize these avionic system be of higher fidelity and better consistency then is present in FASTE-CNS system. This presentation will explore the capabilities of FASTE-CNS with renewed emphasis on the enhancements being added to perform these processing functions; the fidelity and reliability of CNS models necessary to make the enhancements work; and the benchmarking of FASTE-CNS results to improve confidence for the results of the new processing capabilities.

Mainger, Steve↗

The Fleet Application for Scheduling and Tracking (FAST) Management Website

The FAST application was designed to replace the paper and pen method of checking out and checking in GSA Vehicles at KSC. By innovating from a paper and pen based checkout system to a fully digital one, not only the resources wasted by printing the checkout forms have been reduced, but it also reduces significantly the time that users and fleet managers need to interact with the system as well as improving the record accuracy for each vehicle. The vehicle information is pulled from a centralized database server in the SPSDL. In an attempt to add a new feature to the FAST application, the author of this report (alongside the FAST developers) has been designing and developing the FAST Management Website. The GSA fleet managers had to rely on the FAST developers in order to add new vehicles, edit vehicles and previous transactions, or for generating vehicles reports. By providing an easy-to-use FAST Management Website portal, the GSA fleet managers are now able to easily move vehicles, edit records, and print reports.

Object-Oriented Programming↗

Calibration and Validation of a FAST Floating Wind Turbine Model of the DeepCwind Scaled Tension-Leg Platform: Preprint

With the intent of improving simulation tools, a 1/50th-scale floating wind turbine atop a TLP was designed based on Froude scaling by the University of Maine under the DeepCwind Consortium. This platform was extensively tested in a wave basin at MARIN to provide data to calibrate and validate a full-scale simulation model. The data gathered include measurements from static load tests andfree-decay tests, as well as a suite of tests with wind and wave forcing. A full-scale FAST model of the turbine-TLP system was created for comparison to the results of the tests. Analysis was conducted to validate FAST for modeling the dynamics of this floating system through comparison of FAST simulation results to wave tank measurements. First, a full-scale FAST model of the as-tested scaledconfiguration of the system was constructed, and this model was then calibrated through comparison to the static load, free-decay, regular wave only, and wind-only tests. Next, the calibrated FAST model was compared to the combined wind and wave tests to validate the coupled hydrodynamic and aerodynamic predictive performance. Limitations of both FAST and the data gathered from the tests arediscussed.

17 WIND ENERGY↗

Advances in High Harmonic Fast Wave Heating of NSTX H-mode Plasmas

High-harmonic fast wave (HHFW) heating and current drive is being developed in NSTX to provide bulk electron heating and q(0) control during non-inductively sustained Hmode plasmas fuelled by deuterium neutral-beam injection (NBI). In addition, it is used to assist the plasma current ramp-up. A major modification to increase the RF power limit was made in 2009; the original end-grounded, single end-powered current straps of the 12- element array were replaced with center-grounded, double end-powered straps. Greater than 3 MW have been coupled into NBI-driven, ELMy H-mode plasmas with this upgraded antenna. Improved core HHFW heating, particularly at longer wavelengths and during low-density start-up and plasma current ramp-up, has been obtained by lowering the edge density with lithium wall conditioning, thereby moving the critical density for fast-wave propagation away from the vessel wall [1]. Significant core electron heating of NBI-fuelled H-modes has been observed for the first time over a range of launched wavelengths and H-modes can be accessed by HHFW alone. Visible and IR camera images of the antenna and divertor indicate that fast wave interactions can deposit considerable RF energy on the outboard divertor plate, especially at longer wavelengths that begin to propagate closer to the vessel walls. Edge power loss can also arise from HHFWgenerated parametric decay instabilities; edge ion heating is observed that is wavelength dependent. During plasmas where HHFW is combined with NBI, there is a significant enhancement in neutron rate, and fast-ion D-alpha (FIDA) emission measurements clearly show broadening of the fast-ion profile in the plasma core. Large edge localized modes (ELMs) have been observed immediately following the termination of RF power, whether the power turn off is programmed or due to antenna arcing. Causality has not been established but new experiments are planned and will be reported. Fast digitization of the reflected power signal indicates a much faster rise time for arcs than for ELMs. Based on this observation, an ELM/arc discrimination system is being implemented to maintain RF power during ELMs even when the reflection coefficient becomes large. This work is supported by US DOE contracts DE-AC-05-00OR22725 and DE-AC02- 09CH11466. References [1] C. K. Phillips, et al, Nuclear Fusion 10, 075015 (2009)

Ryan, Philip Michael↗

A Workflow to Optimize Fast Neutron Irradiation in A Thermal Neutron Spectrum Test Reactor Leveraging Open-Source Tools

The Advanced Test Reactor (ATR) located at Idaho National Laboratory (INL) is one of the key nuclear engineering research and testing facilities within the US Department of Energy (DOE). The ATR is one of few high-power research reactors in the world with different application including accelerated testing of nuclear fuel, materials irradiation in a very high neutron flux environment, and medical radioisotope production [1]. Also, the ATR offers opportunities for testing fast spectrum fission and fusion reactor materials. The key challenges in this area are in further detailing and optimizing a fast spectrum environment within a thermal test reactor. This challenge involves researching, developing, and testing novel concepts for the multiplying of neutron populations into ever higher energy spectra in high flux test reactors like ATR. The main objective of this work is to investigate candidate materials for establishing a fast neutron experiment irradiation in thermal neutron spectrum test reactors which can be accomplished by filtering thermal and epithermal neutrons and boosting fast neutrons at designated irradiation positions. However, adding these filters will render the neutron spectrum and the criticality of the system. The selection of the thickness and material layers should be accomplished by developing an optimization design algorithm that is applicable for ATR to enhance the fast neutron spectrum irradiation utilizing high-fidelity Monte Carlo methods along with advanced machine learning capabilities. This paper presents workflow for design optimization to enhance fast neutron irradiation in the ATR. The workflow leverages open-source tools to develop an algorithm that is viable to ATR and can be leveraged in other reactors. The following sections discuss the development of the experiment design optimization workflow and its application to ATR irradiation positions.

42 - ENGINEERING↗