Search NASA⌕ Search

SEARCH · Search NASA

Results for “Floating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Y-MP floating point and Cholesky factorization

The floating point arithmetics implemented in the Cray 2 and Cray Y-MP computer systems are nearly identical, but large scale computations performed on the two systems have exhibited significant differences in accuracy. The difference in accuracy is analyzed for Cholesky factorization algorithm, and it is found that the source of the difference is the subtract magnitude operation of the Cray Y-MP. The results from numerical experiments for a range of problem sizes are presented, and an efficient method for improving the accuracy of the factorization obtained on the Y-MP is presented.

Carter, Russell↗
NASA NTRS1992

Heat transfer and fluid flow in floating-zone crystal growth with a mostly covered melt surface

Computer simulation was conducted to study a modified floating-zone crystal growth process, in which the melt surface is mostly covered with a heated ring. The growth of 6-mm diameter single crystals of NaNO3 was considered, and the effects of the following parameters were studied: (1) temperature of the ring, (2) growth rate, (3) surface tension-temperature coefficient of the melt, (4) thermal expansion coefficient of the melt, and (5) gravity. It was demonstrated that thermocapillary convection in the melt zone is reduced significantly in this modified process. The model was checked against the measured lengths of the meniscus near the growth front and axial temperature distribution in a growing crystal, and the agreement was good.

Lan, C. W.↗
NASA NTRS1993

Stability and instability of thermocapillary convection in models of the float-zone crystal-growth process

This project was concerned with the determination of conditions of guaranteed stability and instability for thermocapillary convection in a model of the float-zone crystal-growth process. This model, referred to as the half-zone, was studied extensively, both experimentally and theoretically. Our own earlier research determined, using energy-stability theory, sufficient conditions for stability to axisymmetric disturbances. Nearly all results computed were for the case of a liquid with Prandtl Number Pr = 1. Attempts to compute cases for higher Prandtl numbers to allow comparison with the experimental results of other researchers were unsuccessful, but indicated that the condition guaranteeing stability against axisymmetric disturbances would be a value of the Marangoni number (Ma), significantly higher than that at which oscillatory convection was observed experimentally. Thus, additional results were needed to round out the stability picture for this model problem. The research performed under this grant consisted of the following: (1) computation of energy-stability limits for non-axisymmetric disturbances; (2) computation of linear-stability limits for axisymmetric and non-axisymmetric disturbances; (3) numerical simulation of the basic state for half- and full-zones with a deformable free surface; and (4) incorporation of radiation heat transfer into a model energy-stability problem. Each of these is summarized briefly below.

Neitzel, G. P.↗
NASA NTRS1992

Space Station Freedom structure floating potential and the probability of arcing

The interaction between a space system and the space environment has been one of the driving questions for the design of spacecraft since the dawn of the space age. The Space Station Freedom will represent a significant increase in spacecraft size, power, and activity relative to spacecraft that are currently in orbit. The structure floating potential on Space Station Freedom is studied with simple analytical models of the current collection. The probability of arcing due to dielectric breakdown is assessed.

Hastings, Daniel E.↗
NASA NTRS1928

The reaction on a float bottom when making contact with water at high speeds

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion. The same test data indicate clearly the existence of forces and moments tending to produce the phenomenon observed by Mr. Carroll (Technical Note No. 287) when the maneuver is carried out at lower speeds, as in a landing.

Richardson, H C↗
NASA NTRS1938

Hydrodynamic and Aerodynamic Tests of Four Models of Outboard Floats : (N.A.C.A. Models 51-A, 51-B, 51-C, and 51-D)

Four models of outboard floats (N.A.C.A. models 51-A, 51-B, 51-C, and 51-D) were tested in the N.A.C.A. tank to determine their hydrodynamic characteristics and in the 20-foot wind tunnel to determine their aerodynamic drag. The results of the tests, together with comparisons of them, are presented in the form of charts. From the comparisons, the order of merit of the models is estimated for each factor considered. The best compromise between the various factors seems to be given by model 51-D. This model is the only one in the series with a transverse step.

Dawson, John R↗
NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack IV : floating tip ailerons on rectangular wings

This report is the fourth of a series on systematic tests conducted which compares lateral control devices with particular reference to their effectiveness at high angles of attack. The present report covers tests with floating tip ailerons on rectangular Clark y wings. Ailerons of two profiles were tested - symmetrical and Clark y, both with adjustable trailing-edge flaps. Each form was tested at three hinge-axis locations, both with and without vertical end plates between the ailerons and the wing proper. The results from these tests are compared with the results from tests on a wing of the same over-all size equipped with average-sized ordinary ailerons.

Weick, Fred E↗
NASA NTRS1934

The Development of Floats and Equipment for Research in Promoting It

Providing information that will make possible a favorable compromise between landing impact and planing resistance is the immediate problem in experimental float development. A description of equipment to perform dropping tests are included as well as how to determine the landing impact.

Pabst, Wilhelm↗
NASA NTRS1933

Scale Effect of Model in Seaplane-float Investigations

For the purpose of solving all the problems involved, an investigation was made with flat, rectangular planing surfaces. The investigation of a flat, rectangular planing surface, which can be considered as the portion of a flat float bottom lying in front of the step, has the advantage that the frictional resistance can be determined directly from the test results. Normal and tangential forces act on the lower side of the planing surface towed through still water, while the upper side and the lateral edges are under constant atmospheric pressure.

Sottorf, W↗
NASA NTRS1993

Growth of semiconductor compound single crystal InSb by floating zone method (M-3)

Floating zone methods have potential applications in growing single high-quality semi-conductor crystals. In this method, melts can be sustained without containers and, therefore, are free from contamination from the containers. The main objective of this project is to use the Image Furnace to study a large diameter, (20 mm) single crystal of InSb under microgravity conditions. The behavior of the liquid column is recorded on the VTR tapes and is compared with what is expected theoretically. The single crystal grown in space is characterized by comparing it with single crystals grown on the ground with respect to crystallographic and electronic properties. The goal of this project is to confirm the effects of the microgravity on the single crystals.

Nakatani, I.↗
NASA NTRS1992

Evaluation of floating-point sum or difference of products in carry-save domain

An architecture to evaluate a 24-bit floating-point sum or difference of products using modified sequential carry-save multipliers with extensive pipelining is described. The basic building block of the architecture is a carry-save multiplier with built-in mantissa alignment for the summation during the multiplication cycles. A carry-save adder, capable of mantissa alignment, correctly positions products with the current carry-save sum. Carry propagation in individual multipliers is avoided and is only required once to produce the final result.

Wahab, A.↗
NASA NTRS1995

Interpretation of IEEE-854 floating-point standard and definition in the HOL system

The ANSI/IEEE Standard 854-1987 for floating-point arithmetic is interpreted by converting the lexical descriptions in the standard into mathematical conditional descriptions organized in tables. The standard is represented in higher-order logic within the framework of the HOL (Higher Order Logic) system. The paper is divided in two parts with the first part the interpretation and the second part the description in HOL.

MULTIPLICATION SUBTRACTION↗
NASA NTRS1996

Laser-Heated Floating Zone Production of Single-Crystal Fibers

This report describes how a laser-heated floating zone apparatus can be used to investigate single-crystal fibers of various compositions. A feedrod with a stoichiometric composition of high-purity powders was connected to a pedestal and fed into a laser scan where it combined with a single-crystal fiber seed. A molten zone was formed at this junction. As the feedrod was continuously fed into the laser scan, a single-crystal fiber of a prescribed orientation was withdrawn from the melt. The resultant fibers, whose diameters ranged from 100 to 250 gm, could then be evaluated on the basis of their growth behavior, physical properties, mechanical properties, and fiber perfection.

Ritzert, Frank↗
NASA NTRS1996

CMOS Active-Pixel Image Sensor With Simple Floating Gates

Experimental complementary metal-oxide/semiconductor (CMOS) active-pixel image sensor integrated circuit features simple floating-gate structure, with metal-oxide/semiconductor field-effect transistor (MOSFET) as active circuit element in each pixel. Provides flexibility of readout modes, no kTC noise, and relatively simple structure suitable for high-density arrays. Features desirable for "smart sensor" applications.

Fossum, Eric R.↗
NASA NTRS1997

Lithium-ion drifting: Application to the study of point defects in floating-zone silicon

The use of lithium-ion (Li(+)) drifting to study the properties of point defects in p-type Floating-Zone (FZ) silicon crystals is reported. The Li(+) drift technique is used to detect the presence of vacancy-related defects (D defects) in certain p-type FZ silicon crystals. SUPREM-IV modeling suggests that the silicon point defect diffusivities are considerably higher than those commonly accepted, but are in reasonable agreement with values recently proposed. These results demonstrate the utility of Li(+) drifting in the study of silicon point defect properties in p-type FZ crystals. Finally, a straightforward measurement of the Li(+) compensation depth is shown to yield estimates of the vacancy-related defect concentration in p-type FZ crystals.

Silicon↗
NASA NTRS1999

Utilizing Controlled Vibrations in a Microgravity Environment to Understand and Promote Microstructural Homogeneity During Floating-Zone Crystal Growth

It has been demonstrated in floating-zone configurations utilizing silicone oil and nitrate salts that mechanically induced vibration effectively minimizes detrimental, gravity independent, thermocapillary flow. The processing parameters leading to crystal improvement and aspects of the on-going modeling effort are discussed. Plans for applying the crystal growth technique to commercially relevant materials, e.g., silicon, as well as the value of processing in a microgravity environment are presented.

Grugel, Richard N.↗