Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride

The difficult ignition of boron decreases the combustion efficiency of boron-loaded, fuel-rich propellants. One approach to solving this problem involves the use of magnesium diboride (MgB2), which ignites easier than boron. Magnesium tetraboride (MgB4) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures were recently recognized as promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their thermal decomposition, oxidation, and combustion. The MgB2 and MgB4 powders were fabricated by combustion synthesis in the chemical oven mode and by heating Mg/B mixtures in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by high-energy ball milling. Thermal decomposition and oxidation of the obtained MgB₂ and MgB₄ powders were investigated by conducting non-isothermal thermogravimetric analysis (TGA) at temperatures up to 1550 °C in argon and oxygen flows. Combustion of B, MgB₂, and MgB₄ powders with oxygen at atmospheric pressure was studied in a windowed chamber using laser ignition and high-speed video recording. The TGA has shown multi-step decomposition of both magnesium borides in an argon environment. The maximum oxidation rate of MgB4 in oxygen was observed at a much lower temperature than in the case of MgB2. In the combustion experiments, both magnesium borides burned much faster than submicron boron. Ball milling of the borides further increased their burning rates. It has been concluded that nanoscale magnesium tetraboride is a promising ingredient for fuel-rich propellants owing to its high energy density, efficient oxidation, and rapid combustion.

Molina, Andre [The University of Texas at El Paso]↗
DOE OSTI2022

Non-destructive analysis of swelling in the EMPIrE fuel test

The European Mini-Plate Irradiation Experiment (EMPIrE) was designed to support the development and testing of a coated uranium-molybdenum (U-Mo) dispersion fuel for the conversion of select high-performance research reactors (HPRRs) to utilize low-enriched uranium (LEU). To aid in the development of the coated fuel form, the EMPIrE test included several plate designs and irradiated them in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) at a high meat power density (~21 kW/cm 3 ) and to high fuel particle fission densities (~6.4 × 10 21 fissions/cm 3 ). These conditions mimic the bounding conditions of the BR-2 reactor in Belgium, where a concurrent irradiation experiment was performed, and exceed those previously explored in dispersion U-Mo fuel plates. A local fuel swelling analysis, as determined through high-fidelity, post-irradiation mini-plate profilometry, was used along with statistical methods to non-destructively evaluate the overall performance and separate the effects of convoluted fabrication variables. While some effects observed with this non-destructive analysis were subtle, others had more significant, and possibly competing, effects on the fuel swelling behavior. In closing, these observations will be examined further with destructive examinations to more fully assess them as the fuel design is developed and qualified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

2022 roadmap on 3D printing for energy

The energy transition is one of the main challenges of our society and therefore a major driver for the scientific community. To ensure a smart transition to a sustainable future energy scenario different technologies such as energy harvesting using solar cells or windmills and chemical storage in batteries, super-capacitors or hydrogen have to be developed and ultimately deployed. New fabrication approaches based on additive manufacturing and the digitalization of the industrial processes increase the potential to achieve highly efficient and smart technologies required to increase the competitiveness of clean energy technologies against fossil fuels. In this frame, the present roadmap highlights the tremendous potential of 3D printing as a new route to fully automate the manufacturing of energy devices designed as digital files. Additionally, this article gives numerous guidelines to maximize the performance and efficiency of the next generation of 3D printed devices for the energy transition while reducing the waste of critical raw materials. In particular, the paper is focused on the current status, present challenges and the expected and required advances of 3D printing for the fabrication of the most relevant energy technologies such as fuel cells and electrolysers, batteries, solar cells, super-capacitors, thermoelectric generators, chemical reactors and turbomachinery.

36 MATERIALS SCIENCE↗
DOE OSTI2020

TEV-3349 "ATF-2 2A Loop Pin Cladding Requirements"

Industry partners, including Westinghouse, Framatome, General Electric, General Atomics, Toshiba, etc. require requirements for fuel pins they insert in the reactor for testing. This document contains those requirements. These requirements represent an agreement between ATR and NS&T, and include the requirements for pins fabricated at the INL. These include inspections such as radiography, helium leak check, etc.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO 2 Reduction Using Physical Vapor Deposition Methods

Electrochemical CO 2 reduction (ECR) promises the replacement of fossil fuels as the source of feedstock chemicals and seasonal storage of renewable energy. While much progress has been made in catalyst development and electrochemical reactor design, few studies have addressed the effect of catalyst integration on device performance. Using a microfluidic gas diffusion electrolyzer, we systematically studied the effect of thickness and the morphology of electron beam (EB) and magnetron-sputtered (MS) Cu catalyst coatings on ECR performance. We observed that EB-Cu outperforms MS-Cu in current density, selectivity, and energy efficiency, with 400 nm thick catalyst coatings performing the best. Additionally, the superior performance of EB-Cu catalysts is assigned to their faceted surface morphology and sharper Cu/gas diffusion layer interface, which increases their hydrophobicity. Tests in a large-scale zero-gap electrolyzer yielded similar product selectivity distributions with an ethylene Faradaic efficiency of 39% at 200 mA/cm 2 , demonstrating the scalability for industrial ECR applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Status of the Down-Blending of Irradiated IGR Graphite Fuel in Kazakhstan

Dry processing remains the primary solution for managing the down-blending of irradiated IGR HEU fuel. Several tasks have been initiated and completed to achieve this, including lab modernization, lab-scale and full-scale testing, designing and fabricating an in-paddle mixing drum, and commissioning both a down-blending system and a crushing and milling system. Additionally, a testing and training center was modernized, the equipment was successfully commissioned, and the IGR HEU fuel blocks were repackaged into daily containers. The training of operators and the construction of a new down-blending facility are tasks that will need to be completed in the near future. The progress in these areas continues to validate that the proposed method for down-blending irradiated HEU graphite fuel, followed by cementation of the down-blended material for permanent disposition, appears to be achievable.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2023

Ultrathin electron and proton-conducting membranes for nanoscale integrated artificial photosystems

Reducing the thickness of separation membranes without compromising their selectivity and robustness is the most effective way of maximizing the areal conductivity. This is especially important for the integration of visible light-driven water oxidation and carbon dioxide (or proton) reduction into a complete artificial photosystem on the shortest possible length scale – the nanoscale – because of the efficiency advantages over macroscale photosystems. In addition to their excellent separation property, ultrathin membranes of 10 nm thickness or less need to exhibit sufficient electrical and proton conductivity in order for the photocatalytic rates to keep up with the photon flux at maximum solar intensity. Furher, two materials, graphene and amorphous silica with embedded molecular wires, have emerged as promising ultrathin membranes for the development of nanoscale integrated solar-fuel systems. Moreover, electrically conducting metal–organic or covalent–organic frameworks can be used to fabricate high surface area-supports that enable the use of molecular catalysts and/or light absorbers at an adequate areal density for nanoscale integration with graphene membranes. Following an overview of the electron and proton conductivity of these ultrathin materials and recent examples of photoelectrocatalytic applications that take advantage of some but not all the properties that constitute a complete functional membrane, the status and future opportunities for complete nanoscale integrated photosystems featuring an ultrathin membrane are discussed.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Irradiation Testing of Additively Manufactured Materials for LWR Applications: Alloy 718 and 316L Stainless Steel

The objective of this NSUF Project is to assess the changes in irradiated additively manufactured (AM) material properties as compared to non-irradiated material. Type 316L stainless steel and Alloy 718 samples were produced using Direct Metal Laser Melting (DMLM) fabrication. Materials produced from this fabrication method have several potential applications within the nuclear industry as reactor internal repair parts, fuel debris resistant filters, or fuel spacers within existing light water reactors (LWRs). AM materials have been shown to achieve equivalent mechanical behavior in simulated reactor environments as compared to wrought materials, but have significantly more flexibility when it comes to unique design features. The increased component design flexibility makes these AM materials an attractive choice for both current LWR applications as well as for small modular reactor (SMR) designs. Prior to use of these materials in reactor fleet operation, the industry as a whole must evaluate the effects of irradiation on their material properties. Standard 0.4 inch thick Compact Tension specimens and SSJ3 type tensile bars were neutron irradiated at the Advanced Test Reactor to ~1 dpa for the purpose of performing a variety of mechanical tests in a range of simulated environments applicable to LWRs. For the ductile austenitic Type 316L stainless steel, the irradiated data will be used to confirm that the AM process produces materials with properties that are equivalent to wrought materials under testing conditions applicable to LWR operation. Transmission electron microscopy analysis was also performed in order to understand microstructural and microchemical changes induced in each material in response to neutron irradiation. If possible, data collected from these AM 316L samples will be used to remove fluence limits from specifications of ASME code cases for this alloy, which will give vendors much more flexibility in building future components.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

AGR-5/6/7 Thermal Model with Non-uniform Gas Gaps

Fuel compact temperatures are a crucial factor in assessing irradiation performance of the Tristructural isotropic fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a three-dimensional finite element thermal model, which is subject to simulation uncertainty. The most dominant factor in uncertainty of calculated fuel temperature is the gas gap uncertainty due to the nub-to-shell clearance because of fabrication error. A revision to the thermal model was made to examine the most probable offset position for four different dates of interest. The offset position options varied in magnitude and azimuthal direction of offset of the holder top and bottom position. The best-fit offset of the holder is estimated based on the minimum root mean square error of residuals for all operational thermocouples (TCs). From these results, the following conclusions were made: 1) During earlier cycles (162A – 164A) when numerous TCs were still operational, the best-fit offset distance varied in range [0.002 – 0.0035 in.] for both the top and bottom holder while offset azimuthal direction varied widely, especially for the holder bottom. 2) Holder offset led to slightly lower Capsule 1 average temperature, but wider temperature variation (lower minimum and higher peak fuel temperatures). 3) The maximum offset of 0.006 in. to the northwest direction for both the top and bottom holder yielded a much higher temperature than the original peak fuel temperature, which increased from 1422 to 1557 ? (or 135 ? increase). This could be one of the reasons for massive particle failure near the end of Cycle 165A. 4) Even though, the highest temperature at the TC-1-7 tip reached slightly higher than 1000?, the temperature along the TC wire reached as high as 1335? assuming a holder offset of 0.006 in. to the northwest. Consequently, at this temperature nickel from this TC wire could cause particle failures in Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

An overview of bipolar plates in proton exchange membrane fuel cells

Bipolar plates are a crucial component of proton exchange membrane fuel cells. They are responsible for transporting reactant gases, carrying the current from the membrane electrode assembly to the end plates, providing heat and water management, and separating the individual cells. However, these plates also contribute to 80% of the fuel cell’s weight, 50% of its volume, and 40% of its cost, posing a barrier to the commercialization of fuel cells. This paper provides a comprehensive review of the materials and manufacturing processes used in the fabrication of bipolar plates as well as recent research conducted on the improvement of bipolar plate weight, volume, and cost through material selection and manufacturing methods. Additive manufacturing is highlighted in this work as an innovative manufacturing method to produce bipolar plates. Novel contributions in this paper include a detailed explanation of traditional manufacturing processes for metallic and graphitic-polymer bipolar plates as well as a cost comparison between additive and traditional manufacturing processes.

08 HYDROGEN↗
DOE OSTI2020

Experimental assessment of antimony (Sb) in pure uranium for immobilizing fission product lanthanides

The use of fuel additives is one of the concepts to mitigate fuel cladding chemical interaction (FCCI) for metallic fuel because fission product lanthanides are expected to be immobilized by the additive. Antimony (Sb) has been discovered to be a good candidate in UZr fuel. The present study focuses on its mechanism for immobilization in pure uranium, U–4Sb alloy was fabricated to understand the Sb behavior, while U–4Sb–4Ce was fabricated to simulate the case when lanthanides are generated. Both of the as-cast and annealed samples were characterized by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). U–Sb precipitates are formed in U–4Sb alloy, while U–Sb and Ce–Sb were found in U–4Sb–4Ce alloy, thermal exposure does not change the Sb-precipitation morphologies or chemical composition. Furthermore, diffusion couple tests between those alloys and cladding materials (Fe or HT9) under 650 °C for 500 h were performed and analyzed using SEM/EDS. Diffusion couple tests demonstrate the reaction between cladding and uranium, while no reaction between Sb-precipitations and cladding materials was found.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Fission Accelerated Steady-state Testing (FAST)

In an effort to accelerate the irradiation time for advanced reactor fuels, a revised capsule design has been analyzed and developed for the Advanced Fuels Campaign (AFC). This design incorporates a highly enriched, reduced diameter fuel pin that is doubly encapsulated by two steel capsules. This design alloys accelerated irradiations and reduced sensitivity to fabrication variances and eccentricities. The capsule designs utilize existing experiment baskets from the AFC capsules in the Advanced Test Reactor (ATR) outer A position (FAST-OA) and the ATF-1 capsules in the small I position (FAST-SI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Bio-inspired gas sensing: boosting performance with sensor optimization guided by “machine learning”

The performance of existing gas sensors often degrades in field conditions because of the loss of measurement accuracy in the presence of interferences. Thus, new sensing approaches are required with improved sensor selectivity. We are developing a new generation of gas sensors, known as multivariable sensors, that have several independent responses for multi-gas detection with a single sensor. In this study, we analyze the capabilities of natural and fabricated photonic three-dimensional (3-D) nanostructures as sensors for the detection of different gaseous species, such as vapors and non-condensable gases. We employed bare Morpho butterfly wing scales to control their gas selectivity with different illumination angles. Next, we chemically functionalized Morpho butterfly wing scales with a fluorinated silane to boost the response of these nanostructures to the vapors of interest and to suppress the response to ambient humidity. Further, we followed our previously developed design rules for sensing nanostructures and fabricated bioinspired inorganic 3-D nanostructures to achieve functionality beyond natural Morpho scales. These fabricated nanostructures have embedded catalytically active gold nanoparticles to operate at high temperatures of ≈300 °C for the detection of gases for solid oxide fuel cell (SOFC) applications. Our performance advances in the detection of multiple gaseous species with specific nanostructure designs were achieved by coupling the spectral responses of these nanostructures with machine learning (a.k.a. multivariate analysis, chemometrics) tools. Our newly acquired knowledge from studies of these natural and fabricated inorganic nanostructures coupled with machine learning data analytics allowed us to advance our design rules for sensing nanostructures toward the required gas selectivity for numerous gas monitoring scenarios at room and high temperatures for industrial, environmental, and other applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Burnable absorbers in nuclear reactors – A review

Burnable absorbers can benefit nuclear reactors of virtually any design by providing reactivity control for extended fuel cycles, tritium production, burning of long-lived radionuclides, and reactor safety. When selecting the ideal burnable absorber type and its design, one must consider the resulting impact on the reactor’s fuel cycle design and cost, reactivity, thermal hydraulics, manufacturing, and radiation response. These selection criteria, as well as neutronic and thermophysical material property requirements, may be vastly different depending on whether the burnable absorber is intended for use in a commercial water-cooled reactor, a research reactor, or a next-generation advanced reactor system. A recent integration, synthesis, description of past and present technologies, and identification of existing gaps and areas of future research is lacking on these important topics. Here, this paper includes a fundamental description of the use of burnable absorbers and their impacts on reactivity, absorber depletion, self-shielding, basic thermophysical properties, and the use of burnable absorbers in next-generation nuclear applications..

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Development of an Efficient Conjugate Heat Transfer Modeling Framework to Optimize Mixing-Limited Combustion of Ethanol in a Diesel Engine

Mixing controlled combustion of alcohol fuels has been identified as a promising technology based on their low propensity for particulate and NOx production, but the higher heats of vaporization and auto-ignition temperatures of these fuels make their direct use in diesel engine architectures a challenge. To realize the potential of alcohol-fueled combustion, a computational fluid dynamics (CFD) modeling framework is developed, validated, and exercised to identify designs that maximize engine thermal efficiency. To evaluate the use of thermal barrier coatings (TBCs), a simplified one-dimensional (1D) conjugate heat transfer (CHT) modeling framework is employed. The addition of the 1D CHT model only increases the computational expense by 15% relative to traditional approaches, yet offers more accurate heat transfer predictions over constant temperature boundary conditions. The validated model is then used to explore a range of injector orientations and piston bowl geometries. Using a design of experiments (DoE) approach, several designs were identified that improved fuel-air mixing, shortened the combustion duration, and increased thermal efficiency. The most promising design was fabricated and tested in a Caterpillar 1Y3700 single-cylinder oil test engine (SCOTE). Engine testing confirmed the findings from the CFD simulations and found that the co-optimized injector and piston bowl design yielded over 2-percentage point increase in thermal efficiency at the same equivalence ratio (0.96) and over 6-percentage point increase at the same engine load (10.1 bar indicated mean effective pressure (IMEP)), while satisfying design constraints for peak pressure and maximum pressure rise rate.

Magnotti, Gina M.↗
DOE OSTI2020

Greenhouse gases, Regulated Emissions, and Energy use in Technologies Model ® (2020 .Net)

To fully evaluate energy and emission impacts of advanced vehicle technologies and new transportation fuels, the fuel cycle from wells to wheels and the vehicle cycle through material recovery and vehicle disposal need to be considered. Sponsored by the U.S. Department of Energy's Office of Energy Efficiency and Renewable Energy (EERE), Argonne has developed a full life-cycle model called GREET (Greenhouse gases, Regulated Emissions, and Energy use in Technologies). It allows researchers and analysts to evaluate various vehicle and fuel combinations on a full fuel-cycle/vehicle-cycle basis. The first version of GREET was released in 1996. Since then, Argonne has continued to update and expand the model. GREET.Net provides the user with an easy to use and fully graphical toolbox to perform life cycle analysis simulations of alternative transportation fuels and vehicle technologies in a matter of a few clicks. It provides a comprehensive, life-cycle-based approach to compare the energy use and emissions of conventional and advanced vehicle technologies. The tool includes the data of both fuel-cycle (fuel production and vehicle operation) and vehicle-cycle (vehicle material recovery and production, vehicle component fabrication, vehicle assembly, and vehicle disposal/recycling). This public domain model is available free of charge for anyone to use.

Wang, Michael↗
DOE OSTI2021

Greenhouse gases, Regulated Emissions, and Energy use in Technologies Model ® (2021 .Net)

To fully evaluate energy and emission impacts of advanced vehicle technologies and new transportation fuels, the fuel cycle from wells to wheels and the vehicle cycle through material recovery and vehicle disposal need to be considered. Sponsored by the U.S. Department of Energy's Office of Energy Efficiency and Renewable Energy (EERE), Argonne has developed a full life-cycle model called GREET (Greenhouse gases, Regulated Emissions, and Energy use in Technologies). It allows researchers and analysts to evaluate various vehicle and fuel combinations on a full fuel-cycle/vehicle-cycle basis. The first version of GREET was released in 1996. Since then, Argonne has continued to update and expand the model. GREET.Net provides the user with an easy to use and fully graphical toolbox to perform life cycle analysis simulations of alternative transportation fuels and vehicle technologies in a matter of a few clicks. It provides a comprehensive, life-cycle-based approach to compare the energy use and emissions of conventional and advanced vehicle technologies. The tool includes the data of both fuel-cycle (fuel production and vehicle operation) and vehicle-cycle (vehicle material recovery and production, vehicle component fabrication, vehicle assembly, and vehicle disposal/recycling). This public domain model is available free of charge for anyone to use.

Wang, Michael↗
DOE OSTI2022

Greenhouse gases, Regulated Emissions, and Energy use in Technologies Model ® (2022 .Net)

To fully evaluate energy and emission impacts of advanced vehicle technologies and new transportation fuels, the fuel cycle from wells to wheels and the vehicle cycle through material recovery and vehicle disposal need to be considered. Sponsored by the U.S. Department of Energy's Office of Energy Efficiency and Renewable Energy (EERE), Argonne has developed a full life-cycle model called GREET (Greenhouse gases, Regulated Emissions, and Energy use in Technologies). It allows researchers and analysts to evaluate various vehicle and fuel combinations on a full fuel-cycle/vehicle-cycle basis. The first version of GREET was released in 1996. Since then, Argonne has continued to update and expand the model. GREET.Net provides the user with an easy to use and fully graphical toolbox to perform life cycle analysis simulations of alternative transportation fuels and vehicle technologies in a matter of a few clicks. It provides a comprehensive, life-cycle-based approach to compare the energy use and emissions of conventional and advanced vehicle technologies. The tool includes the data of both fuel-cycle (fuel production and vehicle operation) and vehicle-cycle (vehicle material recovery and production, vehicle component fabrication, vehicle assembly, and vehicle disposal/recycling). This public domain model is available free of charge for anyone to use.

Wang, Michael↗