Search NASA⌕ Search

SEARCH · Search NASA

Results for “High loading rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The thickness effect was accounted for by using a 'constraint' factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data was obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of predicted-to-experimental lives was 0.95 with a standard error of 0.2 for a constraint factor of 1.9.

Newman, J. C., Jr.↗

High strain rate nanoindentation testing: Recent advancements, challenges and opportunities

Recent advancements in electronics have renewed the interest in high strain rate nanoindentation testing, resulting in the development of new high strain rate nanoindentation test equipment and test methodologies. Here, in this work, the current state-of-the-art in high strain rate nanoindentation testing is critically reviewed, with focus on three key aspects - the testing equipment's dynamic mechanical and electronic response, test methodology, and post-processing of raw data to obtain hardness and strain rate. The challenges in instrument hardware design and post-test data analysis are discussed, along with optimal strain rate window for accurate high strain rate measurements. Specific focus will be on instrumented high strain rate testing using self-similar indenters at strain rates in excess of 100 s -1 , wherein load and depth of penetration into the sample are both measured or applied.

36 MATERIALS SCIENCE↗

Alterations in crack-tip deformation during variable-amplitude fatigue crack growth

Fatigue crack growth rate changes caused by single overloads and an overload followed by an underload have been studied in the high-strength aluminum alloy 7091. Crack-tip plasticity parameters were measured at each step in the loading sequence using the stereoimaging technique. Effective stress-intensity factor was measured with high resolution immediately at the crack tip both before an overload and during the subsequent growth rate retardation period. Crack-tip opening displacement and strain were altered in the same way as growth rate following the overload/underload events, and similitude with respect to crack-tip plasticity was preserved during the growth retardation period. Effective stress-intensity factor was found to correlate well with crack growth rate. Strains within the plastic zone were converted to stress at each step in load change. These stresses were then summed to determine the zone of residual stress caused by the overload. The region of compressive residual stress ahead of the crack tip was found to increase with overload severity but was limited to yield stress in magnitude. An underload shrank the spatial extent of the residual stresses caused by the overload.

Davidson, David L.↗

Creep Strain and Strain Rate Response of 2219 Al Alloy at High Stress Levels

As a result of high localized plastic deformation experienced during proof testing in an International Space Station connecting module, a study was undertaken to determine the deformation response of a 2219-T851 roll forging. After prestraining 2219-T851 Al specimens to simulate strains observed during the proof testing, creep tests were conducted in the temperature range from ambient temperature to 107 C (225 F) at stress levels approaching the ultimate tensile strength of 2219-T851 Al. Strain-time histories and strain rate responses were examined. The strain rate response was extremely high initially, but decayed rapidly, spanning as much as five orders of magnitude during primary creep. Select specimens were subjected to incremental step loading and exhibited initial creep rates of similar magnitude for each load step. Although the creep rates decreased quickly at all loads, the creep rates dropped faster and reached lower strain rate levels for lower applied loads. The initial creep rate and creep rate decay associated with primary creep were similar for specimens with and without prestrain; however, prestraining (strain hardening) the specimens, as in the aforementioned proof test, resulted in significantly longer creep life.

Taminger, Karen M. B.↗

Relative humidity threshold for oxygen generation by high-purity plutonium dioxides in 3013 containers

High-purity plutonium dioxide with adsorbed water in a sealed container can generate oxygen, but oxygen will not be generated in low water loading conditions. A threshold for oxygen generation has been observed in the hydrogen generation rate normalized by the specific power for high-purity plutonium dioxide. Normalized hydrogen generation rates above this threshold generate oxygen and below the threshold consume oxygen. The threshold rate is determined by the amount of water adsorbed onto the surface of the oxide. The relative humidity of the atmosphere that the oxide is in equilibrium with determines the amount of physisorbed water adsorbed on the surface. We calculate the relative humidity corresponding to the threshold rate as a function of mass and specific surface area of material stored in 3013 containers. Exceeding the calculated relative humidity may result in flammable gas mixtures of hydrogen and oxygen at some time during storage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The long lives of giant clumps and the birth of outflows in gas-rich galaxies at high redshift

Star-forming disk galaxies at high redshift are often subject to violent disk instability, characterized by giant clumps whose fate is yet to be understood. The main question is whether the clumps disrupt within their dynamical timescale (≤50 Myr), like the molecular clouds in today's galaxies, or whether they survive stellar feedback for more than a disk orbital time (≈300 Myr) in which case they can migrate inward and help building the central bulge. We present 3.5-7 pc resolution adaptive mesh refinement simulations of high-redshift disks including photoionization, radiation pressure, and supernovae feedback. Our modeling of radiation pressure determines the mass loading and initial velocity of winds from basic physical principles. We find that the giant clumps produce steady outflow rates comparable to and sometimes somewhat larger than their star formation rate, with velocities largely sufficient to escape the galaxy. The clumps also lose mass, especially old stars, by tidal stripping, and the stellar populations contained in the clumps hence remain relatively young (≤200 Myr), as observed. The clumps survive gaseous outflows and stellar loss, because they are wandering in gas-rich turbulent disks from which they can reaccrete gas at high rates compensating for outflows and tidal stripping, overall keeping realistic and self-regulated gaseous and stellar masses. The outflow and accretion rates have specific timescales of a few 10{sup 8} yr, as opposed to rapid and repeated dispersion and reformation of clumps. Our simulations produce gaseous outflows with velocities, densities, and mass loading consistent with observations, and at the same time suggest that the giant clumps survive for hundreds of Myr and complete their migration to the center of high-redshift galaxies. These long-lived clumps are gas-dominated and contain a moderate mass fraction of stars; they drive inside-out disk evolution, thickening, spheroid growth, and fueling of the central black hole.

79 ASTRONOMY AND ASTROPHYSICS↗

A computationally efficient ductile damage model accounting for nucleation and micro-inertia at high triaxialities

The computational formulation of a micro-mechanical material model for the dynamic failure of ductile metals is presented in this paper. The statistical nature of porosity initiation is accounted for by introducing an arbitrary probability density function which describes the pores nucleation pressures. Each micropore within the representative volume element is modeled as a thick spherical shell made of plastically incompressible material. The treatment of porosity by a distribution of thick-walled spheres also allows for the inclusion of micro-inertia effects under conditions of shock and dynamic loading. The second order ordinary differential equation governing the microscopic porosity evolution is solved with a robust implicit procedure. A new Chebyshev collocation method is employed to approximate the porosity distribution and remapping is used to optimize memory usage. The adaptive approximation of the porosity distribution leads to a reduction of computational time and memory usage of up to two orders of magnitude. Moreover, the proposed model affords consistent performance: changing the nucleation pressure probability density function and/or the applied strain rate does not reduce accuracy or computational efficiency of the material model. The numerical performance of the model and algorithms presented is tested against three problems for high density tantalum: single void, one-dimensional uniaxial strain, and two-dimensional plate impact. Here, the results using the integration and algorithmic advances suggest a significant improvement in computational efficiency and accuracy over previous treatments for dynamic loading conditions.

42 ENGINEERING↗

Understanding the impact of flow rate and recycle on the conversion of a complex biorefinery stream using a flow-through microbial electrolysis cell

We investigated the effect of flow rate and recycle on the conversion of a biomass-derived pyrolysis aqueous phase in amicrobial electrolysis cell (MEC) to demonstrate production of renewable hydrogen in biorefinery. A continuous MEC operation was investigated under one-pass and recycle conditions usingthe complex, biomass-derived, fermentable, mixed substrate feed at a constant concentration of 0.026 g/L,while testing flow rates ranging from 0.19 to 3.6 mL/min. This corresponds to an organic loading rate (OLR) of 0.54₋10 g/L-day. Mass transfer issues observed at low flow rates were alleviated using high flow rates.Increasing the flow rate to 3.6 mL/min (3.7 min HRT) during one-pass operation increased the hydrogen productivity 3-fold, but anode conversion efficiency (ACE) decreased from 57.9% to 9.9%. Recycle of the anode liquid helped to alleviate kinetic limitations and the ACE increased by 1.8-fold and the hydrogen productivity by 1.2-fold compared to the one-pass condition at the flow rate of 3.6 mL/min (10 g/L-d OLR). High COD removal was also achieved under recycle conditions, reaching 74.2 1.1%, with hydrogen production rate of 2.92 ± 0.51 L/L-day. This study demonstrates the advantages of combining faster flow rates with a recycle process to improve rate of hydrogen production from a switchgrass-derived stream in the biorefinery.

08 HYDROGEN↗

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a crack-tip plasticity concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The effect of material thickness on plasticity was accounted for by using a constraint factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data were obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of the ratio of predicted-to-experimental lives was 0.95 and the standard error was 0.2 using a constraint factor of 1.9 in the model. Crack-opening stresses calculated from the model were significantly different from those determined by Zhang et al. using a striation-based experimental method.

Newman, J. C., Jr.↗

Large-diameter and heteroatom-doped graphene nanotubes decorated with transition metals as carbon hosts for lithium–sulfur batteries

This work addresses here performance issues of lithium–sulfur (Li–S) batteries via retaining the polysulfide intermediates within a novel cathode nanocarbon host. Herein, we report a series of nitrogen and oxygen co-doped and transition metal-decorated large size (200–500 nm in diameter) graphene nanotubes (M-GNTs) (M = Co, Ni, and/or Fe) as effective carbon hosts for sulfur cathodes (S@M-GNTs) in Li–S batteries. The exceptionally large diameters of the graphene tubes allow facile diffusion of sulfur inside the tubes with sufficient loadings, yet leaving room for volume expansion during the lithiation process. The GNTs with the largest diameter and abundant N and O doping along with FeCoNi alloy decoration (FeCoNi-GNTs) exhibit the best sulfur cathode performance. In addition to the unique nanocarbon structures, the heteroatom dopants and transition metal nanoparticles likely also play promotional roles in retaining long-chain polysulfide discharge intermediates within the carbon host, therefore improving rate capability and cycle stability. In particular, a S@FeCoNi-GNT cathode with a high sulfur loading (~4.5 mg S cm -2 ) exhibits discharge capacities up to 1234.7 mA h g -1 at C/20 and 909.0 mA h g -1 at C/5. A discharge capacity of 554.4 mA h g -1 at 1C after 500 cycles was retained, further demonstrating its encouraging potential in Li–S batteries.

25 ENERGY STORAGE↗

Mechanical characterization of 304L-VAR stainless steel in tension with a full coverage of low, intermediate, and high strain rates

A 304L-VAR stainless steel is mechanically characterized in tension over a full range of strain rates from low, intermediate, to high using a variety of apparatuses. While low- and high-strain-rate tests are conducted with a conventional Instron and a Kolsky tension bar, the tensile tests at intermediate strain rates are conducted with a fast MTS and a Drop-Hopkinson bar. The fast MTS used in this study is able to obtain reliable tensile response at the strain rates up to 150 s -1 , whereas the lower limit for the Drop-Hopkinson bar is 100 s -1 . Combining the fast MTS and the Drop-Hopkinson bar closes the gap within the intermediate strain rate regime. Using these four apparatuses, the tensile stress-strain curves of the 304L-VAR stainless steel are obtained at strain rates on each order of magnitude ranging from 0.0001 to 2580 s -1 . All tensile stress-strain curves exhibit linear elasticity followed by significant work hardening prior to necking. After necking occurrs, the specimen load decreases, and the deformation becomes highly localized until fracture. The tensile stress-strain response of the 304L-VAR stainless steel exhibits strain rate dependence. The flow stress increases with increasing strain rate and is described with a power law. The strain-rate sensitivity is also strain-dependent, possibly due to thermosoftening caused by adiabatic heating at high strain rates. The 304L-VAR stainless steel shows significant ductility. The true strains at the onset of necking and at failure are determined. The results show that the true strains at both onset of necking and failure decrease with increasing strain rate. The true failure strains are approximately 200% at low strain rates but are significantly lower (~100%) at high strain rates. The transition of true failure strain occurs within the intermediate strain rate range between 10 -2 and 10 2 s -1 . A Boltzmann description is used to present the effect of nominal strain rate on true failure strain.

304L-VAR stainless Steel↗

High-pressure magnetically driven compression waves in condensed matter.

The Z machine is a fast pulsed-power machine at Sandia National Laboratories designed to deliver a 100-ns rise-time, 26-MA pulse of electrical current to Z-pinch experiments for research in radiation effects and inertial confinement fusion. Since 1999, Z has also been used as a current source for magnetically driven, high-pressure, high-strain-rate experiments in condensed matter. In this mode, Z produces simultaneous planar ramp-wave loading, with rise times in the range of 300-800 ns and peak longitudinal stress in the range of 4-400 GPa, of multiple macroscopic material samples. Control of the current-pulse shape enables shockless propagation of these ramp waves through samples 1-2 mm thick to measure quasi-isentropic compression response, as well as shockless acceleration of copper flyer plates to at least 28 km/s for impact experiments to measure ultra-high-pressure (-3000 GPa) shock compression response. This presentation will give background on the relevant physics, describe the experimental technique, and show recent results from both types of experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enabling high rate charge and discharge capability, low internal resistance, and excellent cycleability for Li-ion batteries utilizing graphene additives

A liquid-phase mixing method is adopted to uniformly disperse the graphene nanosheets onto LiNi 1/3 Co 1/3 Mn 1/3 O 2 cathode for high-performance Li-ion batteries (LIBs). The electrochemical performance was characterized using a full pouch cells with state-of-the-art electrode areal loading (compared to half coin cells). The addition of graphene sheets (i.e., only 1 wt%) significantly improves the high rate capability for charging and discharging operation. For example, 6 times improvement in 5 C charging was achieved providing further insights in enabling extreme fast charging for LIBs. Other benefits include longer cycleability, lower internal resistance, and higher lithium ion diffusion coefficient, demonstrated by charge-discharge cycling tests and electrochemical impedance spectroscopy. Higher capacity retention of 88.2% and decreased internal resistance of ~0.9 Ω are observed after 400 cycles. The diffusion coefficient of Li ions is 6.49 × 10 -8 cm 2 s -1 when charged to 4.2 V, which is approximately 1.37 times higher compared to the configuration with no graphene sheet (4.74 × 10 -8 cm 2 s -1 ). To conclude, the improved performance is ascribed to a robust network among the active materials formed by graphene sheets, which serves as an extended current conductor and facilitates charge transfer, ionic reversibility, and ionic transportation.

25 ENERGY STORAGE↗

Crack Propagation Modeling of a High-Speed Outer Rotor Motor

This study aims to investigate the propagation of initial cracks in electric motors and their rate of spread through the rotor structure under various operating conditions. Traction motors are subjected to high centrifugal load owing to their speed and rapid acceleration and deceleration. In the manufacturing process, some initial imperfections or cracks in the rotor components are likely to occur. Under the influence of loading, these cracks will grow, and factors such as loading frequency, material strength, and location of material voids will affect this threshold speed. In the current study, a fracture mechanics–based approach has been used to investigate the crack growth rate for a 100 kW outer rotor motor with a rated speed of 6,000 rpm and a peak speed of 20,000 rpm for an integrated drive application.

Barua, Himel↗

A chemical kinetic analysis of knock propensity of methanol-to-gasoline fuel

Production of low carbon gasoline-like fuels such as methanol-to-gasoline (MTG) is a promising approach to achieve rapid greenhouse gas emission reduction of the transportation sector. Despite the fact that gasoline that meets the ASTM D4814 standard for automotive spark-ignition engine fuel can be readily produced from these processes, it is unclear how the composition of MTG may affect engine performance and emissions. Here, in this paper, a surrogate for an MTG is used to numerically study the effects of gasoline composition on knock propensity and on the sensitivity of knock to thermal and fuel stratification, to oxygen dilution and to nitric oxide from exhaust gas recirculation of residual gases. Simulations were performed in ANSYS CHEMKIN-PRO using a comprehensive chemical kinetic mechanism for gasoline surrogates, and results of the MTG surrogate were compared against those of a petroleum-based regular E10 gasoline, termed PACE-20. A premium-grade MTG fuel was also formulated by adding ethanol to the MTG surrogate, and results were compared against those of four premium-grade, gasoline-like fuels representative of future alternative gasoline formulations. Surrogates and mechanism were evaluated by comparison against experimental engine data, and the model showed high accuracy at stoichiometric conditions (mean absolute error of ignition timing equal to 1.46 crank angle degrees) but larger deviations at lean conditions (mean absolute error of ignition timing equal to 5.52 crank angle degrees). Despite the fact that the MTG surrogate has a RON 1.1 units higher than that of PACE-20, it may show higher knock propensity at medium temperature conditions due to a less intense NTC behavior. MTG autoignition was more temperature- and equivalence ratio-sensitive than that of PACE20, suggesting that MTG can benefit more from naturally-occurring thermal stratification or from induced fuel stratification of the end gas to mitigate knock intensity. The sensitivity of autoignition reactivity to oxygen dilution and to NO concentration was higher for MTG than for regular gasoline at medium loads, but the opposite trend was observed at high loads due to the effect of pressure on the low-temperature chemistry of regular gasoline. Approximately 14 % vol ethanol content was required to upgrade the octane rating of MTG from regular grade to premium grade. Adding 13.6 % vol ethanol made the fuel autoignition less sensitive to both oxygen dilution and NO content (ignition time varies approx. 17 % and 50 % less with oxygen dilution and NO addition, respectively, when adding ethanol at high engine loads).

02 PETROLEUM↗

Hydro-isostatic deflection and tectonic tilting in the central Andes: Initial results of a GPS survey of Lake Minchin shorelines

Sufficiently large lake loads provide a means of probing rheological stratification of the crust and upper mantle. Lake Minchin was the largest of the late Pleistocene pluvial lakes in the central Andes. Prominent shorelines, which formed during temporary still-stands in the climatically driven lake level history, preserve records of lateral variations in subsequent net vertical motions. At its maximum extent the lake was 140 m deep and spanned 400 km N-S and 200 km E-R. The load of surficial water contained in Lake Minchin was sufficient to depress the crust and underlying mantle by 20-40 m, depending on the subjacent rheology. Any other differential vertical motions will also be recorded as departures from horizontality of the shorelines. We recently conducted a survey of shoreline elevations of Lake Minchin with the express intent of monitoring the hydro-isostatic deflection and tectonic tilting. Using real-time differential Global Positioning System (GPS), we measured topographic profiles across suites of shorelines at 15 widely separated locations throughout the basin. Horizontal and vertical accuracies attained are roughly 30 and 70 cm, respectively. Geomorphic evidence suggests that the highest shoreline was occupied only briefly (probably less than 200 years) and radiocarbon dates on gastropod shells found in association with the shore deposits constrain the age to roughly 17 kyr. The basin-side pattern of elevations of the highest shoreline is composed of two distinct signals: (27 +/- 1) m of hydro-isostatic deflection due to the lake load, and a planar tilt with east and north components of (6.8 +/- 0.4) 10(exp -5) and 9-5.3 +/- 0.3) 10(exp -5). This rate of tilting is too high to be plausibly attributed to steady tectonism, and presumably reflects some unresolved combination of tectonism plus the effects of oceanic and lacustrine loads on a laterally heterogeneous substrate. The history of lake level fluctuations is still inadequately known to allow detailed inferences of crust and mantle rheology. However, it is already clear that the effective elastic plate thickness is closer to 40 km than the 60-70 km crustal thickness in the central Andes and the effective viscosity is less than 5 10(exp 20) Pa s.

Bills, Bruce G.↗

Effects of particle size, shape and loading rate on the normal compaction of an advanced granular ceramic

Compaction behavior of granular materials is influenced by strain rate, particle size, and shape. In this report, boron carbide powders with different particle sizes under uni-axial strain conditions are studied using quasi-static compression, dynamic Kolsky bar experiments and normal plate impact. A rounded powder is compacted to investigate the effect of particle shape. The normal plate impact technique is an excellent tool in characterization of powder compaction behavior up to strain rates of ~10 5 s -1 . From our experiments, granular boron carbide shows a highly compressible behavior with significant volume compaction. Constitutive responses are obtained for four powders. Particle fracture is identified as key deformation mechanism. Dynamic loading introduces more particle fragmentation than quasi-static loading. Morphological characterization of particle shapes shows that the deformation from powder compaction alters the particle shape distribution, which is also rate-dependent. Particle size, shape and strain rate effects on the normal stress are discussed accordingly.

36 MATERIALS SCIENCE↗

Monodomain Liquid‐Crystal Elastomer Lattices for Broad Strain‐Rate Mechanical Damping

Designing structures that effectively dissipate energy across a broad range of mechanical loading rates, including those from compression, shock, and vibration, poses a significant engineering challenge. In this study, liquid‐crystal elastomers (LCEs), which possess anisotropic properties due to the alignment of their polymer backbone, are explored. As a result, LCEs exhibit a soft elastic response under mechanical loading, making them ideal for energy dissipation. Advances in additive manufacturing (AM) enable simple fabrication of foamlike dissipative structures with complex lattice geometries. Herein, direct ink write 3D printing, an extrusion AM method, is used to fabricate aligned, monodomain LCE lattice structures for broad strain‐rate mechanical damping. In this work, it is shown that these structures can dissipate strain energy in quasi‐static environments, comparable to traditional elastomeric lattices, and provide improved damping under high strain‐rate drop testing due to LCE soft elasticity. Additionally, under dynamic mechanical vibration, monodomain LCE lattices enhance damping at structural natural frequencies and provide high‐frequency attenuation. Finally, in these findings, a promising method is presented for fabricating mechanical damping devices that effectively dissipate energy across a broad range of loading rates.

3D printings↗