SEARCH · Search NASA

Results for “LOADS - RINGS, CIRCULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS2018

Effect of Distributed Patch of Smooth Roughness Elements on Transition in a High-Speed Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of hypersonic vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, smooth-shaped roughness elements on the laminar boundary layer over a 7-degree half-angle, circular cone for flow conditions corresponding to a selected trajectory point from the ascent phase of the HIFiRE-1 flight experiment. For peak-to-valley roughness heights of 50 percent or less in comparison with the thickness of the unperturbed boundary layer, the computations converge to a stationary flow, suggesting that the flow is globally stable. Analysis of convective instabilities in the wake of the roughness patch indicates two dominant families of unstable disturbances, namely, a high frequency mode that corresponds to Mack mode waves modified by the wake and a lower frequency mode that corresponds to shear layer instabilities associated with the streaks in the roughness wake. Even though the peak growth rate of the later mode is more than 35 percent greater than the peak growth rates of the Mack modes, the latter modes achieve higher amplification ratios, and hence, are likely to dominate the onset of transition, which is estimated to occur slightly later than that in the unperturbed, i.e., smooth surface boundary layer. Additional computations are performed to investigate the effects of various roughness patch configurations on a Mach 3.5 flat plate boundary layer, to help guide an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at NASA Langley Research Center. In this case, the cumulative reinforcement of basic state distortion over the length of the roughness patch is predicted to yield a significantly earlier transition than that over a smooth plate or a plate with a shorter length roughness patch.

Meelan Choudhari↗

NASA NTRS2024

Test and Analysis of the 8-foot Diameter Cylindrical Sandwich Composite Test Article CTA8.2B: As part of the NASA Engineering and Safety Center Shell Buckling Knockdown Factor Project

The buckling response of thin-walled cylindrical structures have long been shown to be sensitive to various imperfections. That is, imperfections related to load introduction, boundary conditions, material property variation, and geometric deviations can all contribute to experimentally obtained buckling loads being lower than the buckling loads predicted for perfect representations of the same thin-walled cylindrical structure. To account for the influence of geometry-based imperfections of a thin-walled cylindrical structure on buckling response, a design factor (also known as a buckling knockdown factor) is used during the design phase. Guidelines for buckling knockdown factors are readily available in NASA SP-8007, Buckling of Thin Walled Circular Cylinders, which was updated in 2020. Prior to this recent update, NASA SP-8007 had not been updated since 1969, and since that time, computational analysis, experimental testing, and manufacturing methods have significantly improved. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF, NESC Assessment 07-010-E) had the goal of developing buckling design recommendations for select classes of metallic and composite launch-vehicle structures [3]. Specifically, the test and analysis results from the fourth SBKF composite test article SBKF-P3-CYL-CTA8.2B, which is referred to as CTA8.2B, are described in this paper. This test was the fourth in a series of four tests on sandwich composite cylinders that will be used to experimentally validate analysis methods, which in turn can be used to develop new analysis-based shell buckling design guidelines for typical sandwich composite launch vehicle cylindrical structures. Publications describing previous test validation with analysis are available in Refs. CTA8.2B was designed to occupy one corner of the design space with approximately equal bending stiffnesses in the axial and transverse directions and have a larger ratio of radius to effective shell thickness. Each test article had a unique design and was designed to occupy a specific region of the design space. CTA8.2B was an 8-foot diameter honeycomb-core sandwich cylinder that was fabricated and tested at the NASA Marshall Space Flight Center (MSFC). The primary objectives of this test were to interrogate the structural capability of a composite test article, and to verify the test article design and analysis approach for cylinders subjected to axial compression and combined axial and bending loads. First, descriptions of the test article design and test are given in Section 2.0, and modeling and analysis methods used in support of the test article design and testing activities are described briefly in Section 3.0. Then, select test results are presented and compared to predicted results in Section 4.0, and concluding remarks are presented in Section 5.0. Finally, drawings of CTA8.2B and references used to support the test and analysis are provided in the Appendix.

Nonlinear analysis↗

NASA NTRS1977

Fatigue damage in notched composite laminates

This communication describes the results of an experimental investigation of the fatigue characteristics of a boron-epoxy laminate containing an unloaded circular hole. The study focuses upon characterization of the fatigue damage incurred and its influence upon axial tensile residual strength. Two apparent anomalies in the fatigue behavior for this laminate were observed. First, the fatigue damage was observed to propagate tangentially to the edge of the notch (parallel to the direction of the load), in contrast to propagation in contemporary metallic materials which is perpendicular to the load direction. Second, the residual strength characteristics for the laminate have revealed a significant increase in residual strength subsequent to a fatigue loading of 500,000 cycles at R = 0.1 and S = 0.8 and 0.67 (S = maximum stress/static ultimate). Failure analyses of the fatigue damage are conducted utilizing ultrasonic 'C' scan techniques.

Pipes, R. B.↗

NASA NTRS1980

Integrated application of active controls (IAAC) technology to an advanced subsonic transport project. Conventional baseline configuration study

Characteristics of the U.S. domestic fleet were evaluated to determine the mission characteristics that would have the most impact on U. S. transport fuel use in the future. This resulted in selection of a 197-passenger (plus cargo), about 3710-km (2000 nmi) mission. The existing data base was reviewed and additional analysis was conducted as necessary to complete the technical descriptions. The resulting baseline configuration utilizes a double-lobe, but nearly circular, body with seven-abreast seating. External characteristics feature an 8.71 aspect ratio, 31.5-degree sweep wing, a T-tail empennage, and a dual CF6-6D2, wing-mounted engine arrangement. It provides for 22 LD-2 or 11 LD-3 containers plus bulk cargo in the lower lobe. Passenger/cargo loading, servicing provisions, taxi/takeoff speeds, and field length characteristics are all compatible with accepted airline operations and regulatory provisions. The baseline configuration construction uses conventional aluminum structure except for advanced aluminum alloys and a limited amount of graphite epoxy secondary structure. Modern systems are used, including advanced guidance, navigation, and controls which emphasize application of digital electronics and advanced displays.

Source record↗

NASA NTRS1985

Finite element method for nonlinear forced vibrations of circular plates

Geometric nonlinearities for large amplitude free and forced vibrations of circular plates are investigated. Inplane displacement and inertia are included in the formulation. Finite element method is used. Harmonic force matrix for nonlinear forced vibration analysis is introduced and derived. Various out-of-plane and inplane boundary conditions are considered. The relations of amplitude - frequency ratio for different boundary conditions and various loads conditions are presented.

Decha-Umphai, K.↗

NASA NTRS1988

Temperature effect on stress concentration around circular hole in a composite material specimen representative of X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite was used to manufacture the X-29A forward-swept wing. It was found for composite material, that the anisotropic stress concentration is no longer a constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be reduced drastically, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor of room temperature. The results predicted by the mixture rule approach were about twenty percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of the stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗

NASA NTRS1989

A test method to measure the response of composite materials under reversed cyclic loads

A test method to measure the response of composite materials under reversed cyclic loads is described. The method approximates the long-term response of a component by permitting the composite specimen to respond to the imposed loads and fail in an unconstrained mode rather than in a constrained mode. The method has been successfully used for the reversed cyclic loading of unnotched and notched graphite/epoxy and graphite/PEEK laminates of various stacking sequences. Included in the paper are monotonic tensile and compressive stiffness and strength data at several points in the fatigue lifetime, and damage development information obtained via X-ray radiography for quasi-isotropic T300/5208 and AS4/PEEK laminates with unloaded circular holes.

Bakis, Charles E.↗

NASA NTRS1959

Effect of Convex Longitudinal Curvature on the Planing Characteristics of a Surface Without Dead Rise

A hydrodynamic investigation was made in Langley tank no. 1 of a planing surface which was curved longitudinally in the shape of a circular arc with the center of curvature above the model and had a beam of inches and a radius of curvature of 20 beams. The planing surface had length-beam ratio of 9 and an angle of dead rise of 0 deg. Wetted length, resistance, and trimming moment were determined for values of load coefficient C(sub Delta) from -4.2 to 63.9 and values of speed coefficient C(sub V) from 6 to 25. The effects of convexity were to increase the wetted length-beam ratio (for a given lift), to decrease the lift-drag ratio, to move the center of pressure forward, and ta increase the trim for maximum lift-drag ratio as compared with values for a flat surface. The effects were greatest at low trims and large drafts. The maximum negative lift coefficient C(sub L,b) obtainable with a ratio of the radius of curvature to the beam of 20 was -0.02. The effects of camber were greater in magnitude for convexity than for the same amount of concavity.

Mottard, Elmo J.↗

DOE OSTI2024

Design and optimization of higher order mode couplers for the superconducting cavities of the PERLE energy recovery linac

The Powerful Energy Recovery Linac for Experiments (PERLE) is an energy recovery linac (ERL) facility based on superconducting radio-frequency (SRF) technology to be hosted at the Laboratoire de Physique des 2 Infinis Irène Joliot-Curie (IJCLab) in France. With a target beam power of 10 MW, PERLE aims to demonstrate the high-current, continuous wave, multi-pass operation to validate options for future high-energy machines, such as the 50 GeV ERL proposed for the Large Hadron electron Collider (LHeC) and the Future Circular electron-hadron Collider (FCC-eh), and host dedicated particle physics and nuclear experiments. In high-current ERLs, the regenerative Beam Breakup (BBU), emerging from the beam and cavity Higher Order Modes (HOMs) interaction, is a major concern for their stable operation. Beam-induced HOMs can increase the cavity heat load at cryogenic temperature and cause beam instabilities. HOM couplers are installed in the cavity beam pipes to absorb HOM energy and mitigate these effects. This thesis presents the design and optimization of several coaxial HOM couplers for the 5-cell 801.58 MHz elliptical Nb cavities of the 500 MeV PERLE ERL configuration. The RF transmission of the HOM couplers was optimized to enhance the damping of the most dangerous HOMs. The optimized HOM couplers were integrated into endgroups to simulate their damping performance and thermal behavior. The optimized HOM couplers were 3D-printed in epoxy and copper-coated. Low-power RF measurements were conducted on the produced HOM couplers installed in copper PERLE-type cavities to validate their damping performance and propose several endgroups for the PERLE 5-cell cavity to mitigate HOMs below the BBU instability limits.

Barbagallo, Carmelo↗

NASA NTRS1999

Condensation of Forced Convection Two-Phase Flow in a Miniature Tube

A physical/mathematical model of annular film condensation at the inlet of a miniature tube has been developed. In the model, the liquid flow is coupled with the vapor flow along the liquid-vapor interface through the interfacial temperature, heat flux, shear stress, and pressure jump conditions due to surface tension effects. The model predicts the shape of the liquid-vapor interface along the condenser and leads to the conclusion that there is complete condensation at a certain distance from the condenser inlet. The numerical results show that complete condensation of the incoming vapor is possible at comparatively low heat loads and that this is a special case of a more general condensation regime with two-phase bubbly flow downstream of the initial annular film condensation region. Observations from the flow visualization experiment confirm the existence and qualitative features of annular film condensation leading to the complete condensation phenomenon in a small diameter (3.25 mm) circular tube condenser.

Begg, E.↗

NASA NTRS1981

Green's function for cracks of equal length from a circular hole in an infinite sheet

Stress-intensity factors are obtained for twin collinear cracks emanating from a hole in an infinite plate. Point forces that tend to make the crack surfaces separate and slide are applied to one of the cracks. A conformal mapping and the Muskelishvili formulation involving series representation of the Kolosov stress functions are used to derive the solutions. The variation of stress-intensity factor with crack length and with point of application of the loads is presented for both crack tips.

Shivakumar, V.↗

NASA NTRS1980

Baffle design for earth radiation rejection in the Cryogenic Limb-Scanning Interferometer/Radiometer

The Cryogenic Limb-Scanning Interferometer/Radiometer (CLIR) is being developed to observe infrared emissions of the earth's upper atmosphere from space. The earth's surface is an extended source of intense background radiation with a small angular separation from the desired scene. The CLIR employs an off-axis Gregorian Telescope whose primary mirror and baffles are cooled by an open-cycle cryogen system. A system of specular annular baffles has been developed to minimize both stray light problems and cryogen consumption by retro-mapping the aperture into itself. Each off-axis ray which enters the aperture and strikes the specular baffle surface is reflected so that it passes out of the aperture and is not absorbed on a cryogenic surface. The specular baffle which lies closest to the aperture is an ellipsoid whose foci trace out the circular aperture on revolution about the axis. Its theoretical 'ray trace' efficiency is 100 percent. A subsequent baffle has an elliptical cross section whose near focus traces out the central hole in the ellipsoidal baffle and whose far focus traces out the aperture. Its theoretical efficiency is about 90 percent. These baffles reduce the earth radiation heat load on the cryogenic cooler by an order of magnitude, changing it from the dominant cause of cryogen consumption to a relatively small effect. An aperture shield is also desirable to reduce cryogen consumption, stray light, and contamination.

Bremer, J. C.↗

NASA NTRS1990

Foundation design for a radio telescope on the moon

A foundation design for a 122 m diameter dish-type radio telescope on the moon is presented. The 1.2 m wide and 43 m diameter circular strip footing was analyzed for settlement due to compaction during installation and also for total and differential settlement under in-service laods. An axisymmetrical finite element code of the uppdated Lagrangian formulation was used. Interface slip elements were also used. The nonlinear hyperbolic stress-strain model parameters for the regolith were derived from load-deflection characteristics of astronauts' bootprints and the Rover tracks.

Chua, Koon Meng↗

DOE OSTI2025

Contaminant Investigation and Pre‐Processing Opportunities for Textile‐To‐Textile Recycling

Millions of metric tons of textiles are landfilled or incinerated each year in the United States, with less than 1% of textiles recycled into new clothing or fabrics. To counter this trend, a growing number of companies and researchers are exploring how a circular economy can be applied to support textile‐to‐textile recycling. A significant barrier they face comes down to quickly and efficiently extracting pure feedstock material from post‐consumer garments that feature a mix of natural and synthetic fibers. Textile recyclers prefer pure feedstocks, as working with mixed sources typically means lower throughput, higher risk of equipment failure, and diminished business margins. To facilitate a circular economy for textiles, methods, and technologies are needed that can efficiently separate out materials and contaminants from end‐of‐life textiles to increase the flow of pure feedstocks to recyclers. This paper summarizes findings from interviews with a cross section of textile recyclers and from a review of literature to define basic feedstock requirements. In addition to our qualitative research, we deconstruct a bale of post‐consumer textiles and analyze them using computer‐vision imaging, Fourier transform infrared spectroscopy (FTIR), and machine learning. The resulting data are used to set system‐level design inputs for an automated contaminant removal system to process post‐consumer clothing into appropriate feedstocks for recycling. To set the system's levels for automated real‐time near‐infrared analysis, we identify the minimum percentage of primary material that any single garment in a load of used clothing must contain for the average of the full output stream to meet the target purity levels of recyclers. Here, the envisioned automated system can also address undesirable trace materials that might contaminate the processed stream by using imaging cameras coupled with artificial intelligence to identify sections of clothing for de‐trimming. Proof‐of‐concept machine learning algorithms are evaluated to locate and identify trims or garment areas with hidden contaminant materials. Integrating these methods into automated textile cutting systems can provide a cost‐effective means for increasing feedstock purity from used clothing, which can advance circularity for textiles by helping recyclers to reach production volumes and quality targets that were not possible solely with manual dismantling operations.

Parsons, Ryan [Rochester Institute of Technology, ↗

DOE OSTI2022

Surface Impedance of Nb$_3$Sn and YBa$_2$Cu$_3$O$_{7-\sigma}$ in High Magnetic Fields

New potential rf applications of superconductors emerged with the need to operate in high dc magnetic fields (up to 16 T) where vortex motion dictates the response: the beam screen coating of the Future Circular Collider (FCC) [1] and haloscopes, i.e. rf cavities for the axions detection [2]. However, very few data are available in the required regimes. We present in this work measurements of the surface impedance Z up to 12 T on bulk Nb₃Sn and YBCO thin films grown by different techniques. The measurements are performed with a dielectric loaded resonator operating at 15 GHz. We obtained the vortex motion resistivity and extracted the high frequency vortex motion parameters [3]: the depinning frequency, the flux-flow resistivity and the pinning constant, as well as their temperature and field dependences. Substantial differences are highlighted in the high frequency pinning properties of the studied materials, providing useful information on possible improvements in view of applications. A comparison with the results obtained in the microwave frequency range at lower fields (up to 1 T) is given.

43 PARTICLE ACCELERATORS↗

NASA NTRS1980

Simple computations for near-optimum ascent and abort maneuver targets and deorbit ignition time

Closed-form solutions are presented for a two-burn orbit insertion, AOA, and ATO maneuver targets, and for time of ignition of a one-burn deorbit. Based on the assumption that the orbits involved deviate only to the first order about a reference circular orbit, these solutions are nearly fuel-minimum. They are expressed in terms of linear terminal velocity constraint shuttle guidance targets and, thus, are readily applicable to both ground and onboard software use. In addition to potential application to real-time targeting, the equations may be used as a mission design aid in preliminary definition of target loads and definition of abort mode boundaries.

Mchenry, R. L.↗

NASA NTRS2015

Development of the PRSEUS Multi-Bay Pressure Box for a Hybrid Wing Body Vehicle

NASA has created the Environmentally Responsible Aviation Project to explore and document the feasibility, benefits, and technical risk of advanced vehicle configurations and enabling technologies that will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations that have higher lift-to-drag ratios, reduced drag, and lower community noise. Although such novel configurations like the Hybrid Wing Body (HWB) offer better aerodynamic performance as compared to traditional tube-and-wing aircraft, their blended wing shapes also pose significant new design challenges. Developing an improved structural concept that is capable of meeting the structural weight fraction allocated for these non-circular pressurized cabins is the primary obstacle in implementing large lifting-body designs. To address this challenge, researchers at NASA and The Boeing Company are working together to advance new structural concepts like the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS), which is an integrally stiffened panel design that is stitched together and designed to maintain residual load-carrying capabilities under a variety of damage scenarios. The large-scale multi-bay fuselage test article described in this paper is the final specimen in a building-block test program that was conceived to demonstrate the feasibility of meeting the structural weight goals established for the HWB pressure cabin.

Jegley, Dawn C.↗

NASA NTRS1985

Stress concentration around a small circular hole in the HiMAT composite plate

Anisotropic plate theory is used to calculate the anisotropic stress concentration factors for a composite plate (AS/3501-5 graphite/epoxy composite, single ply or laminated) containing a circular hole. This composite material is used on the highly maneuverable aircraft technology (HiMAT) vehicle. It is found that the anisotropic stress concentration factor could be greater or less than 3 (the stress concentration factor for isotropic materials), and that the locations of the maximum tangential stress points could shift with the change of fiber orientation with respect to the loading axis. The effect of hole size on the stress concentration factor is examined using the Point Stress Criterion and the Averaged Stress Criterion. The predicted stress concentration factors based on the two theories compared fairly well with the measured values for the hole size 0.3175 cm (1/8 in). It is also found that through the lamination process, the stress concentration factor could be reduced drastically, indicating an improvement in structural performance.

Ko, W. L.↗