Search NASA⌕ Search

SEARCH · Search NASA

Results for “LUBRICATING OILS - VISCOSITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Study of lubricant jet flow phenomena in spur gears

Lubricant jet flow impingement and penetration depth into a gear tooth space were measured at 4920 and 2560 rpm using a 8.89 cm (3.5 inch) pitch diameter 8 pitch spur gear at oil pressures from 70,000 to 410,000 n/sqm (10 psi to 60 psi). A high speed motion picture camera was used with xenon and high speed stroboscopic lights to slow down and stop the motion of the oil jet. An analytical model was developed for the vectorial impingement dept and for the impingement depth with tooth space windage effects included. The windage effects for oil drop size greater than .0076 cm (.003 inches). The analytical impingement dept compared favorably with experimental results above an oil jet pressure of 70,000 n/sqm (10psi). There was further penetration into the tooth space after impingement, but much of this oil was thrown out of the tooth space without further contacting the gear teeth.

Akin, L. S.↗

Effects of Water Contamination on Micropitting and Rolling Contact Fatigue of Bearing Steels

Abstract In this research, the effects of water contamination in oil were investigated on two kinds of failures that occur in bearing steel: micropitting and rolling contact fatigue. Whereas the presence of water in the oil had little effect on the generation of surface wear in these experiments, increases in the occurrences of micropitting and rolling contact fatigue were observed due to the presence of either dissolved or free water in lubricants. Additionally, the presence of white etching matter at crack interfaces was observed and evaluated. The experimental results showed that water content can be considered as a significant factor that accelerates the formation of micropitting and fatigue cracks in rolling bearings.

Engineering↗

Evaluation of drilled-ball bearings at DN values to three million. 1: Variable oil flow tests

Two 125-mm-bore solid ball bearings and two similar drilled ball bearings were operated at speeds up to 24,000 rpm (3.0 million DN) with a 13,000 newton (3000 lb) thrust load. The oil flow rate was varied from 0.045 to 0.121 kilograms per second (6 to 16 lb/min). The solid ball bearings operated satisfactorily over the entire range of conditions. The drilled ball bearing experienced cage rub with marginal lubrication at 0.045 kilograms per second (6 lb/min). The drilled ball bearing generally ran cooler than the solid ball bearings.

Holmes, P. W.↗

Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS

The Marine Algae Industrialization Consortium (MAGIC) was formed to address pressing challenges in the commercialization of microalgae as a source of biofuel. The “Marine Algae Industrialization Consortium (MAGIC): Combining biofuel and high-value bioproducts to meet the RFS” project formally addressed two US Department of Energy Bioenergy Technologies Office (BETO) goals: (1) Model the sustainable supply of 1 million metric tonnes ash free dry weight (AFDW) cultivated algal biomass and (2) Demonstrate valuable co-products produced along with biofuel intermediates to increase value of algal biomass by 30%. To achieve these goals, the project demonstrated and validated high-value co-products to drive down the cost of biofuel by increasing the value of algae “co-products” towards increasing the selling price of total algae biomass as one of the key drivers of economics and adoption. This was accomplished through five core, interdependent tasks including: (1) strain selection to identify and deliver strains for mass culture, (2) mass culture using a hybrid cultivation system and following key operating parameters for downstream applications to provide algae feedstock, (3) recovery and conversion to evaluate two alternative methods to separate dry algae biomass into oil and residuals for downstream testing, (4) product assessment to determine biofuel, aquafeed or poultry feed product efficacy using algae biomass fractions as well as to provide critical performance data for valuation and (5) commercialization to use technoeconomic and life cycle assessments (TEA/LCA) as iterative design and assessment tools including consideration of target markets, competitors, and distribution channels to guide product assessment, development and valuation. A total of 46 peer-review publications, many open-access, provide detail of much of the work carried out and the results of the tasks. Additional reports and presentations provide other technical and public engagement material. At a high level, using a variety of approaches, more than 1000 marine microalgae strains were evaluated to ultimately identify the seven winners that were down-selected to be grown in mass culture. Strain selection demonstrated that there were no ‘super strains’ and that each candidate had strengths and limitations for specific products, growth conditions or operational considerations. Mass culture growth of these seven strains at >5000 L / 29 m 2 scale found that four them were suitable for product assessment. More than 250 kg of biomass was produced across hundreds of pond runs along with thousands of cultivation entries on the growth and biomass characteristics as well as environmental parameters. In the process, dozens of standard operating procedures were generated as was custom software to process and analyze cultivation data. Recovery and conversion of algae biomass demonstrated that a hexane solvent based extraction protocol was most effective at recovering oil (biocrude) from algae and four strains were processed to produce oil and lipid extracted algae (residuals) for downstream testing. Membrane-based oil separation was less successful, but may still be applicable to other commercial applications in the future. Product testing demonstrated that algae biocrude is of high quality and hydrotreating generated numerous fractions of high quality composition for fuel and lubricate based applications. Aquafeed studies performed at a variety of scales showed that both whole and defatted (lipid extracted algae) microalgae were suitable as a feed ingredient, but that the specifics of the fed animal and biochemical composition of the algae are critical factors when determining formulation. Similarly, poultry studies on whole and defatted microalgae generally showed positive outcomes on animal growth and health, with some microalgae providing enhanced nutritional composition of the animal product. Economic and life cycle assessments covered a wide range of possible commercialization and sustainability scenarios. Replacement value, improved product value added, consumer values marketing added valuation and improved animal health were considered as alternatives for microalgae valuation. Using the open pond system, algae productivity was identified as the key driver of commercialization economics, but combination of co-products (e.g. animal feed) with biofuel production substantially increased the total selling price of algae. Modeled microalgae selling price exceeded $\$$1500/tonne and could generate competitive biofuel selling prices below $\$$5 gallon gas equivalents using realistic algal productivities. Short (process scale) and longer (decadal trends) sustainability assessments show that marine microalgae can enhance the sustainability of energy production and lead to other realized benefits in water, fertilizer and land use for other sectors (e.g. agriculture). This project successfully demonstrated all of the components of an end-to-end process from mass microalgae cultivation and dewatering, to recovery and conversion of algae biomass components, to final product demonstration and process valuation; the combined results provide a framework for future commercialization of algae based biofuels.

09 BIOMASS FUELS↗

Effect of Surface Roughness on Hydrodynamic Bearings

A theoretical analysis on the performance of hydrodynamic oil bearings is made considering surface roughness effect. The hydrodynamic as well as asperity contact load is found. The contact pressure was calculated with the assumption that the surface height distribution was Gaussian. The average Reynolds equation of partially lubricated surface was used to calculate hydrodynamic load. An analytical expression for average gap was found and was introduced to modify the average Reynolds equation. The resulting boundary value problem was then solved numerically by finite difference methods using the method of successive over relaxation. The pressure distribution and hydrodynamic load capacity of plane slider and journal bearings were calculated for various design data. The effects of attitude and roughness of surface on the bearing performance were shown. The results are compared with similar available solution of rough surface bearings. It is shown that: (1) the contribution of contact load is not significant; and (2) the hydrodynamic and contact load increase with surface roughness.

Majumdar, B. C.↗

Solvent-Induced Selectivity of Isoprene From Bio-Derived Prenol

In this work we demonstrate the selective catalytic conversion of prenol, which is an allylic alcohol that can be prepared from renewable resources to isoprene. The catalyst is an inexpensive molybdenum complex (Molyvan L) designed and used as an additive for lubricants. Isoprene is generated under relatively mild reaction parameters at 130–150°C, for 2 h, under vapor pressure conditions that do not exceed 50 psi. Two cases were studied: one in which Molyvan L was dissolved in a base oil at 1% concentration (weight/weight) and then mixed with a solvent and prenol and the other in which neat Molyvan L was introduced in the reaction and the base oil was replaced with the solvent and prenol. We investigated the selectivity of the reaction using the following solvents in both cases: dodecane, dodecanol, isododecane, octane, blendstock for oxygenate blending (BOB3), a fuel surrogate, a polyalphaolefin (PAO4), and methoxy polyethylene glycol (methoxy PEG350). Although conversion of prenol was above 94% in all experiments, isoprene was formed with various degrees of efficiency alongside a prenol isomeric alcohol, diprenyl ether and mixed ether via intramolecular and intermolecular dehydration reactions. Dodecane appeared to have the highest level of selectivity initially in base oil so we studied the effect of various dodecane-like solvents on isoprene yield and product profile. Surprisingly, octane (similar to dodecane) and isododecane (branched alkane) generated insignificant amounts of byproducts, essentially providing the highly desired isoprene with a very high selectivity. Branching of the solvent does not appear to have an effect on selectivity. Another advantage of this catalyst is the low loadings required to effect the transformation; that is, 0.25% (weight/volume) in the cases using neat Molyvan L and 0.5% (weight/volume) in the cases using Molyvan L dissolved in the base oil. Provided that prenol can be produced in large scale from bioresources, this work would enable the sustainable production of isoprene, in good yield, and with very high selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ferrographic analysis of wear debris from full-scale bearing fatigue tests

The Ferrograph was used to determine the types and quantities of wear particles generated during full scale bearing fatigue tests. Deep-groove ball bearings made from steel were used. A tetraester lubricant was used in a recirculating lubricant system containing a 49 micrometers absolute filter. Test conditions include a maximum Hertz stress of 2.4 GPa, a shaft speed of 15,000 rpm, and a lubricant supply temperature of 74 C (165 F). Four fatigue failures were detected by accelerometers in this test set. In general, the Ferrograph was more sensitive (up to 23 hr) in detecting spall initiation than either accelerometers or the normal spectrographic oil analysis. Four particle types were observed: normal rubbing weather particles, spheres, nonferrous particles, and severe wear (spall) fragments.

Jones, W. R., Jr.↗

Analysis of wear-debris from full-scale bearing fatigue tests using the ferrograph

The ferrograph was used to determine the types and quantities of wear particles generated during full-scale bearing fatigue tests. Deep-groove ball bearings made from AISI 52100 steel were used. A MIL-L-23699 tetraester lubricant was used in a recirculating lubrication system containing a 49 mm absolute filter. Test conditions included a maximum Hertz stress of 2.4 GPa, a shaft speed of 15,000 rpm, and a lubricant supply temperature of 74 C (165 F). Four fatigue failures were detected by accelerometers in this test set. In general, the ferrograph was more sensitive (up to 23 hr) in detecting spall initiation than either accelerometers or the normal spectrographic oil analysis. Four particle types were observed: normal rubbing wear particles, spheres, nonferrous particles, and severe wear (spall) fragments.

Jones, W. R.↗

Analysis of wear debris from full-scale bearing fatigue tests using the Ferrograph

The Ferrograph was used to determine the types of quantities of wear particles generated during full-scale bearing fatigue tests. Deep-groove ball bearings made from AISI 52100 steel were used. A MIL-L-23699 tetraester lubricant was used in a recirculating lubrication system containing a 49-micron absolute filter. Test conditions included a maximum Hertz stress of 2.4 GPa, a shaft speed of 15,000 rpm and a lubricant supply temperature of 74 C (165 F). Four fatigue failures were detected by accelerometers in this test set. In general, the Ferrograph was more sensitive (up to 23 h) in detecting spall initiation than either accelerometers or the normal spectrographic oil analysis (SOAP). Four particle types were observed: normal rubbing wear particles, spheres, nonferrous particles, and severe wear (spall) fragments.

Jones, W. R., Jr.↗

Assessment of two neglected effects in the analysis of an oil pumping ring seal

Many factors have been found to affect the performance of a pumping ring seal. In this paper, two effects (elevated reservoir temperature and rod deformation), both heretofore neglected, are assessed through the use of a thermoelastohydrodynamic numerical model of the pumping ring. Elevated reservoir temperatures are found to result in an increase in the amount of lubricant pumped while deformation of the translating rod is shown to cause a reduction in the lubricant pumped.

Keith, T. G.↗

Investigation of main bearing operating conditions in a three-Point mount wind turbine drivetrain

Wear-related failures of spherical roller bearings in the main bearing position of three-point mount wind turbines have been higher than expected and can contribute to higher than anticipated operation-and-maintenance costs. In this paper, the operational conditions of such a main bearing—including measured axial displacement and velocity subject to the estimated axial loads—are described for an instrumented, commercial wind turbine. The field measurements suggest a maximum axial speed between the bearing rings that is less than 2 millimeters per second. It is estimated that the axial speed between the ring and rollers is approximately 25% of this value. When compared to a speed of rolling from approximately 200–352 millimeters per second, the measured axial sliding is therefore significantly less than 1% of the speed of rolling. Previous numerical studies of lubricant film formation in rolling contacts have shown that the effect of axial sliding starts to be noticeable only when this ratio exceeds 10%; therefore, the axial velocity represents only a small disturbance to the nominal pure rolling case, and the influence on oil film building can be neglected. A simple analytic model of the main bearing motion was also developed and demonstrated similar displacement and velocity characteristics.

17 WIND ENERGY↗

Surface roughness effect on finite oil journal bearings

A theoretical study of the performance of finite oil journal bearings is made, considering the surface roughness effect. The total load supporting ability under such a condition derives from the hydrodynamic as well as asperity contact pressure. These two components of load are calculated separately. The average Reynolds equation for partially lubricated surfaces is used to evaluate hydrodynamic pressure. An analytical expression for average film thickness is obtained and introduced to modify the average Reynolds equation. The resulting differential equation is then solved numerically by finite difference methods for mean hydrodynamic pressure, which in turn gives the hydrodynamic load. Assuming the surface height distribution as Gaussian, the asperity contact pressure is found. The effect of surface roughness parameter, surface pattern, eccentricity ratio, and length to diameter ratio on hydrodynamic load and on side leakage is investigated. It is shown that hydrodynamic load increases with increasing surface roughness when both journal and bearing surfaces have identical roughness structures or when the journal only has a rough surface. The trend of hydrodynamic load is reversed if the journal surface is smooth and the bearing surface is rough.

Majumdar, B. C.↗

Investigation of Main Bearing Operating Conditions in a Three-Point Mount Wind Turbine Drivetrain

Wear related failures of spherical roller bearings in the main bearing position of three-point mount wind turbines have been higher than expected and can contribute to higher than anticipated operation-and-maintenance costs. In this paper, the operational conditions of such a main bearing, including measured axial displacement and velocity subject to the estimated axial loads are described for an instrumented, commercial wind turbine. The field measurements suggest a maximum axial speed between the bearing rings that is less than 2 millimeters per second. It is estimated that the axial speed between the ring and rollers is approximately 25% of this value. When compared to a speed of rolling from approximately 200-352 millimeters per second, the measured axial sliding is therefore significantly less than 1% of the speed of rolling. Previous numerical studies of lubricant film formation in rolling contacts have shown that the effect of axial sliding starts to be noticeable only when this ratio exceeds 10%; therefore, the axial velocity represents only a small disturbance to the nominal pure rolling case, and the influence on oil film building can be neglected. A simple analytic model of the main bearing motion was also developed and demonstrated similar displacement and velocity characteristics.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

Applications of film thickness equations

A number of applications of elastohydrodynamic film thickness expressions were considered. The motion of a steel ball over steel surfaces presenting varying degrees of conformity was examined. The equation for minimum film thickness in elliptical conjunctions under elastohydrodynamic conditions was applied to roller and ball bearings. An involute gear was also introduced, it was again found that the elliptical conjunction expression yielded a conservative estimate of the minimum film thickness. Continuously variable-speed drives like the Perbury gear, which present truly elliptical elastohydrodynamic conjunctions, are favored increasingly in mobile and static machinery. A representative elastohydrodynamic condition for this class of machinery is considered for power transmission equipment. The possibility of elastohydrodynamic films of water or oil forming between locomotive wheels and rails is examined. The important subject of traction on the railways is attracting considerable attention in various countries at the present time. The final example of a synovial joint introduced the equation developed for isoviscous-elastic regimes of lubrication.

Hamrock, B. J.↗

Effect of lubricant extreme pressure additives on rolling element fatigue life

The effects of surface active additives on rolling-element fatigue life were investigated with the five-ball fatigue tester at conditions where classical subsurface initiated rolling-element fatigue is the sole mode of failure. Test balls of AISI 52100, AISI M-50, and AISI 1018 were run with an acid-treated white oil containing either 2.5 percent sulfurized terpene, 1 percent didodecyl phosphite, or 5 percent chlorinated wax. In general, it was found that the influence of surface active additives was detrimental to rolling-element fatigue life. The chlorinated-wax additive significantly reduced fatigue life by a factor of 7. The base oil with the 2.5 percent sulfurized-terpene additive can reduce fatigue life by as much as 50 percent. No statistical change in fatigue life occurred with the base oil having the 1 percent didodecyl-phosphite additive. The additives used with the base oil did not change the ranking of the bearing steels where rolling-element fatigue life was of subsurface origin.

Parker, R. J.↗

Space Shuttle Body Flap Actuator Bearing Testing for NASA Return to Flight

The Space Shuttle body flap is located beneath the main engine nozzles and is required for proper aerodynamic control during orbital descent. Routine inspection of one of four body flap actuators found one of the actuator bearings had degraded and blackened balls. A test program was initiated to demonstrate that it is acceptable to operate bearings which are degraded from operation over several flights. This test exposed the bearing to predicted flight axial loads, speeds and temperatures. Testing at 140 F has been completed, and results indicate the previously flown bearings are acceptable for up to 12 additional missions. Additional testing is underway to determine the lubricant life at various temperatures and stresses and to further understand the mechanism that caused the blacken balls. Initial results of this testing indicates that bearing life is shorten at room temperature possibly due fact that higher temperature (140 F) accelerates the flow of grease and oil into the wear surface

Jett, Timothy R.↗

Oil-Free Enabling Technology: Gas Foil Bearings

NASA has developed and commercialized high temperature coatings and bearings for extreme conditions. These technologies are now under consideration by industry for automotive applications such as turbochargers, fuel cell compressors and exhaust gas path mechanism applications. In this presentation, a review of Oil-Free technologies and their current state-of-development is introduced. Key NASA contributions to the field as documented by patents, research papers and technology demonstrations is also presented.

lubrication↗