Search NASA⌕ Search

SEARCH · Search NASA

Results for “Motion Systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Locomotor head-trunk coordination strategies following space flight

During locomotion, angular head movements act in a compensatory fashion to oppose the vertical trunk translation that occurs during each step in the gait cycle. This coordinated strategy between head and trunk motion serves to aid gaze stabilization and perhaps simplifies the sensory coordinate transformation between the head and trunk, allowing efficient descending motor control during locomotion. Following space flight, astronauts often experience oscillopsia during locomotion in addition to postural and gait instabilities, suggesting a possible breakdown in head-trunk coordination. The goal of the present investigation was to determine if exposure to the microgravity environment of space flight induces alteration in head-trunk coordination during locomotion. Astronaut subjects were asked to walk (6.4 km/h, 20 s trials) on a motorized treadmill while visually fixating on a centrally located earthfixed target positioned either 2 m (FAR) or 30 cm (NEAR) from the eyes. In addition, some trials were also performed during periodic visual occlusion. Head and trunk kinematics during locomotion were determined with the aid of a video-based motion analyzing system. We report data collected preflight (10 days prior to launch) and postflight (2 to 4 hours after landing). The coherence between pitch head and vertical trunk movements during gaze fixation of both FAR and NEAR targets was significantly reduced following space flight indicating decreased coordination between the head and trunk during postflight locomotion. Astronauts flying on their first mission showed greater alterations in the frequency spectra of pitch head movements as compared to their more experienced counterparts. These modifications in the efficacy of head movement control may account for the reported disruption in gaze performance during locomotion and may contribute to postflight postural and gait dysfunction.

NASA Discipline Neuroscience↗
NASA NTRS1993

Overhead and forward reach capability during exposure to +1 to +6 Gx loads

The lack of reach performance data obtained under space-flight conditions has led to questions regarding the operational impact of higher G loads on crew performance. This investigation studied the effect of increasing G loads on reach capability. Ten subjects were exposed in a stepwise fashion to increasing accelerations resulting in G loads of from +1 to +6 Gx in the Brooks AFB centrifuge. Four subjects wore the pre-Challenger Launch Entry Helmet (LEH) ensemble and six the current Launch Entry Suit (LES). The subjects performed standardized reach sweeps at each G level. These sweeps were recorded on videotape and subsequently analyzed using a 3-dimensional motion analysis system. Significant differences in forward and overhead reach were determined using the General Linear Models (GLM) procedure of the Statistical Analysis System (SAS) program. The results from this study suggest that purposeful movement can be realistically performed in the LEH at the 5 G level and in the LES up to the 4 G level.

G Suits/standards↗
NASA NTRS2005

Flow Visualization Proposed for Vacuum Cleaner Nozzle Designs

In 1995, the NASA Lewis Research Center and the Kirby Company (a major vacuum cleaner company) began negotiations for a Space Act Agreement to conduct research, technology development, and testing involving the flow behavior of airborne particulate flow behavior. Through these research efforts, we hope to identify ways to improve suction, flow rate, and surface agitation characteristics of nozzles used in vacuum cleaner nozzles. We plan to apply an advanced visualization technology, known as Stereoscopic Imaging Velocimetry (SIV), to a Kirby G-4 vacuum cleaner. Resultant data will be analyzed with a high-speed digital motion analysis system. We also plan to evaluate alternative vacuum cleaner nozzle designs. The overall goal of this project is to quantify both velocity fields and particle trajectories throughout the vacuum cleaner nozzle to optimize its "cleanability"--its ability to disturb and remove embedded dirt and other particulates from carpeting or hard surfaces. Reference

Source record↗
NASA NTRS2007

On Target to Mars

This viewgraph presentation reviews the use of Descent Image Motion Estimation System (DIMES) for the descent of a spacecraft onto the surface of Mars. In the past this system was used to assist in the landing of the MER spacecraft. The overall algorithm is reviewed, and views of the hardware, and views from Spirit's descent are shown. On Spirit, had DIMES not been used, the impact velocity would have been at the limit of the airbag capability and Spirit may have bounced into Endurance Crater. By using DIMES, the velocity was reduced to well within the bounds of the airbag performance and Spirit arrived safely at Mars. Views from Oppurtunity's descent are also shown. The system to avoid and detect hazards is reviewed next. Landmark Based Spacecraft Pinpoint Landing is also reviewed. A cartoon version of a pinpoint landing and the various points is shown. Mars s surface has a large amount of craters, which are ideal landmarks . According to literatures on Martian cratering, 60 % of Martian surface is heavily cratered. The ideal (craters) landmarks for pinpoint landing will be between 1000 to 50 meters in diagonal The ideal altitude for position estimation should greater than 2 km above the ground. The algorithms used to detect and match craters are reviewed.

Mars↗
NASA NTRS2009

FPGA-Based Networked Phasemeter for a Heterodyne Interferometer

A document discusses a component of a laser metrology system designed to measure displacements along the line of sight with precision on the order of a tenth the diameter of an atom. This component, the phasemeter, measures the relative phase of two electrical signals and transfers that information to a computer. Because the metrology system measures the differences between two optical paths, the phasemeter has two inputs, called measure and reference. The reference signal is nominally a perfect square wave with a 50- percent duty cycle (though only rising edges are used). As the metrology system detects motion, the difference between the reference and measure signal phases is proportional to the displacement of the motion. The phasemeter, therefore, counts the elapsed time between rising edges in the two signals, and converts the time into an estimate of phase delay. The hardware consists of a circuit board that plugs into a COTS (commercial, off-the- shelf) Spartan-III FPGA (field-programmable gate array) evaluation board. It has two BNC inputs, (reference and measure), a CMOS logic chip to buffer the inputs, and an Ethernet jack for transmitting reduced-data to a PC. Two extra BNC connectors can be attached for future expandability, such as external synchronization. Each phasemeter handles one metrology channel. A bank of six phasemeters (and two zero-crossing detector cards) with an Ethernet switch can monitor the rigid body motion of an object. This device is smaller and cheaper than existing zero-crossing phasemeters. Also, because it uses Ethernet for communication with a computer, instead of a VME bridge, it is much easier to use. The phasemeter is a key part of the Precision Deployable Apertures and Structures strategic R&D effort to design large, deployable, segmented space telescopes.

Rao, Shanti↗
NASA NTRS2007

Mapped Landmark Algorithm for Precision Landing

A report discusses a computer vision algorithm for position estimation to enable precision landing during planetary descent. The Descent Image Motion Estimation System for the Mars Exploration Rovers has been used as a starting point for creating code for precision, terrain-relative navigation during planetary landing. The algorithm is designed to be general because it handles images taken at different scales and resolutions relative to the map, and can produce mapped landmark matches for any planetary terrain of sufficient texture. These matches provide a measurement of horizontal position relative to a known landing site specified on the surface map. Multiple mapped landmarks generated per image allow for automatic detection and elimination of bad matches. Attitude and position can be generated from each image; this image-based attitude measurement can be used by the onboard navigation filter to improve the attitude estimate, which will improve the position estimates. The algorithm uses normalized correlation of grayscale images, producing precise, sub-pixel images. The algorithm has been broken into two sub-algorithms: (1) FFT Map Matching (see figure), which matches a single large template by correlation in the frequency domain, and (2) Mapped Landmark Refinement, which matches many small templates by correlation in the spatial domain. Each relies on feature selection, the homography transform, and 3D image correlation. The algorithm is implemented in C++ and is rated at Technology Readiness Level (TRL) 4.

Johnson, Andrew↗
NASA NTRS2004

Sensory-Feedback Exoskeletal Arm Controller

An electromechanical exoskeletal arm apparatus has been designed for use in controlling a remote robotic manipulator arm. The apparatus, called a force-feedback exoskeleton arm master (F-EAM) is comfortable to wear and easy to don and doff. It provides control signals from the wearer s arm to a robot arm or a computer simulator (e.g., a virtual-reality system); it also provides force and torque feedback from sensors on the robot arm or from the computer simulator to the wearer s arm. The F-EAM enables the wearer to make the robot arm gently touch objects and finely manipulate them without exerting excessive forces. The F-EAM features a lightweight design in which the motors and gear heads that generate force and torque feedback are made smaller than they ordinarily would be: this is achieved by driving the motors to power levels greater than would ordinarily be used in order to obtain higher torques, and by providing active liquid cooling of the motors to prevent overheating at the high drive levels. The F-EAM (see figure) includes an assembly that resembles a backpack and is worn like a backpack, plus an exoskeletal arm mechanism. The FEAM has five degrees of freedom (DOFs) that correspond to those of the human arm: 1. The first DOF is that of the side-to-side rotation of the upper arm about the shoulder (rotation about axis 1). The reflected torque for this DOF is provided by motor 1 via drum 1 and a planar four-bar linkage. 2. The second DOF is that of the up-and-down rotation of the arm about the shoulder. The reflected torque for this DOF is provided by motor 2 via drum 2. 3. The third DOF is that of twisting of the upper arm about its longitudinal axis. This DOF is implemented in a cable remote-center mechanism (CRCM). The reflected torque for this DOF is provided by motor 3, which drives the upper-arm cuff and the mechanism below it. A bladder inflatable by gas or liquid is placed between the cuff and the wearer s upper arm to compensate for misalignment between the exoskeletal mechanism and the shoulder. 4. The fourth DOF is that of flexion and extension of the elbow. The reflected torque for this DOF is provided by motor 4 and drum 4, which are mounted on a bracket that can slide longitudinally by a pin-and-slot engagement with the upper-arm cuff to compensate for slight variations in the position of the kinematic center of the elbow. Attached to drum 4 is an adapter plate to which is attached a CRCM for the lower arm. 5. The lower-arm CRCM implements the fifth DOF, which is the twist of the forearm about its longitudinal axis. Motor 5 provides the reflected torque for this DOF by driving the lower-arm cuff. A rod transmits twist and torsion between the lower-arm cuff and the hand cuff. With this system, the motion of the wearer s joints and the reflected torques applied to these joints can be measured and controlled in a relatively simple manner. This is because the anthropomorphic design of the mechanism imitates the kinematics of the human arm, eliminating the need for kinematic conversion of joint-torque and joint-angle data.

An, Bin↗
NASA NTRS2011

Active Response Gravity Offload System

The Active Response Gravity Offload System (ARGOS) provides the ability to simulate with one system the gravity effect of planets, moons, comets, asteroids, and microgravity, where the gravity is less than Earth fs gravity. The system works by providing a constant force offload through an overhead hoist system and horizontal motion through a rail and trolley system. The facility covers a 20 by 40-ft (approximately equals 6.1 by 12.2m) horizontal area with 15 ft (approximately equals4.6 m) of lifting vertical range.

Valle, Paul↗
NASA NTRS2014

NASA Summer 2014

Create a motion validation system using Google Glass and Microsoft Kinect to provide instantaneous feedback for integration with NASA tutorials and procedures.

Fares, Hannelle↗
NASA NTRS2016

Motion Estimation Utilizing Range Detection-Enhanced Visual Odometry

A motion determination system is disclosed. The system may receive a first and a second camera image from a camera, the first camera image received earlier than the second camera image. The system may identify corresponding features in the first and second camera images. The system may receive range data comprising at least one of a first and a second range data from a range detection unit, corresponding to the first and second camera images, respectively. The system may determine first positions and the second positions of the corresponding features using the first camera image and the second camera image. The first positions or the second positions may be determined by also using the range data. The system may determine a change in position of the machine based on differences between the first and second positions, and a VO-based velocity of the machine based on the determined change in position.

Friend, Paul Russell↗
NASA NTRS2016

Documenting the NASA Armstrong Flight Research Center Oblate Earth Simulation Equations of Motion and Integration Algorithm

A desire for more complete documentation of the National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center (AFRC), Edwards, California legacy code used in the core simulation has led to this e ort to fully document the oblate Earth six-degree-of-freedom equations of motion and integration algorithm. The authors of this report have taken much of the earlier work of the simulation engineering group and used it as a jumping-o point for this report. The largest addition this report makes is that each element of the equations of motion is traced back to first principles and at no point is the reader forced to take an equation on faith alone. There are no discoveries of previously unknown principles contained in this report; this report is a collection and presentation of textbook principles. The value of this report is that those textbook principles are herein documented in standard nomenclature that matches the form of the computer code DERIVC. Previous handwritten notes are much of the backbone of this work, however, in almost every area, derivations are explicitly shown to assure the reader that the equations which make up the oblate Earth version of the computer routine, DERIVC, are correct.

integrators↗
NASA NTRS2016

Propellant Savings during Soyuz Undock from the International Space Station

As a vehicle continuously orbiting Earth for over a decade, the International Space Station (ISS) must be conscious of ways to conserve consumables to maximize the efficiency of cargo flights to ISS. One such consumable is propellant. As part of an ongoing effort to minimize propellant usage onboard ISS and use control moment gyroscopes as much as possible for ISS control, an effort was made in late 2014 to allow Soyuz manned vehicle undockings without requiring the use of thrusters. This method, which has been used for four Soyuz undockings, saves up to 160 kg of propellant each year. Fiona completed a B.S. is Mechanical Engienering at Washington University in St. Louis in 2009, after which she moved to Houston, TX to begin working at NASA Johnson Space Center. She currently works in the Flight Operations Directorate as an ADCO (Attitude Determination and Control Officer) flight controller and MCG (Motion Control Group) instructor. Her responsibilities include operating the motion control systems of the ISS in Mission Control, interfacing with Russian colleagues, mentoring and teaching flight controller trainees, and training astronauts for their missions to ISS.

Turett, Fiona↗
NASA NTRS2017

The NASA Augmented/Virtual Reality Lab: The State of the Art at KSC

The NASA Augmented Virtual Reality (AVR) Lab at Kennedy Space Center is dedicated to the investigation of Augmented Reality (AR) and Virtual Reality (VR) technologies, with the goal of determining potential uses of these technologies as human-computer interaction (HCI) devices in an aerospace engineering context. Begun in 2012, the AVR Lab has concentrated on commercially available AR and VR devices that are gaining in popularity and use in a number of fields such as gaming, training, and telepresence. We are working with such devices as the Microsoft Kinect, the Oculus Rift, the Leap Motion, the HTC Vive, motion capture systems, and the Microsoft Hololens. The focus of our work has been on human interaction with the virtual environment, which in turn acts as a communications bridge to remote physical devices and environments which the operator cannot or should not control or experience directly. Particularly in reference to dealing with spacecraft and the oftentimes hazardous environments they inhabit, it is our hope that AR and VR technologies can be utilized to increase human safety and mission success by physically removing humans from those hazardous environments while virtually putting them right in the middle of those environments.

Little, William↗
NASA NTRSDate not supplied

High Fidelity Aerospace Simulations at NASA Ames SimLabs

An overview of the simulation facilities at SimLabs at NASA Ames. Main focus is on the Vertical Motion Simulator or VMS, also brief descriptions of other simulators. Discussion of the history and general specifications of the VMS. Also, provide an overview of past research and training conducted on the simulators, and some future developments with a focus on AR/VR technologies.

flight simulators↗
NASA NTRSDate not supplied

Lunar Surface Mixed Reality and ARGOS Trainer

This Artemis focused Mixed Reality (MR) and ARGOS project extends the current VR/ARGOS CIF project to enhance and add VR/MR capabilities to support analysis, training and risk reduction for lunar surface EVA operations in the extreme South Pole lunar environment. This third year focused on establishing a functional trainer for crew that supports the ingress/egress of a lander as well as surface tasks such as sample collection and tool deployment and operation. Completed enhancements include improving hand tracking, the addition of supporting mixed reality surface operations, and the implementation of a higher fidelity body tracking capability through a motion capture system.

Lunar↗
DOE OSTI2025

The Transient Reactor Test Facility (TREAT)

TREAT operated from 1959-1994, later refurbished & resumed operation in 2017 to support fuel safety testing Zircaloy-clad graphite/fuel blocks comprise core Virtually any power history possible within ~2000 MJ core transient energy capacity From milliseconds to minutes: Pulses, Ramps, LOCA Fuel motion monitoring system “hodoscope” observes fast neutrons emitted from specimens to track fuel relocation in real time Reactor also can be a neutron source to adjacent radiography facility Experiment vehicle does everything else Safety containment, specimen environment, and instrumentation

22 GENERAL STUDIES OF NUCLEAR REACTORS↗