Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase slips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

Seismic Analysis of Spatio-Temporal Fracture Generation During EGS Resource Development

This DOE GTO funded project was a collaborative effort between Array Information Technology and the University of California at Berkeley. The project goal is to improve technology to assess in-situ stress magnitude and orientation, kinematic fracture parameters, rupture size, rupture orientation as well as temporal changes and volumetric distribution of the injected fluid during Enhanced Geothermal System (EGS) resource development. The project leveraged high-frequency seismic data recorded by the LBNL 34-station permanent geophone network and seismic broadband data recorded by a temporary 33-station seismometer network that operated in The Geysers during the injection phase of the DOE GTO funded EGS demonstration project at the well Prati-32. The operation of the broadband network with high station density and good azimuthal coverage to monitor the injection phase produced an unprecedented dataset that is typically unavailable for EGS operations. The two datasets offer the advantages of studying the parameters under investigation over a broader frequency band and the higher sensitivity of the broadband seismometers resulted in a richer dataset with a lower magnitude of completeness. Moment tensor (MT) inversion have been employed to develop a catalog of earthquake source solutions including moment tensor and finite source rupture area. This resulted in a 168-event waveform-based seismic moment tensor catalog for events 0.7≤Mw≤3.9 based on a semi-automated moment tensor analysis technique. The MT solutions were used for in-situ stress estimation during the EGS injection phases. We found an approximate 15-degree counterclockwise rotation of the least compressive stress sigma-3, and a rotation of the maximum compressive stress sigma-1 toward the vertical as the injected volume of water increased. We developed a rupture-area magnitude scaling relationship of The Geysers earthquakes obtained from finite-source inversion for fault slip that reveals a very high correlation to published results. Based on the rupture area-magnitude relationship we mapped Mw from the LBNL earthquake catalog to estimate the activated fracture area, its location and orientation within the injection volume of Prati-32. The double-difference Wadati (DDW) technique was applied to high-accuracy P- and S-wave differential travel times derived from waveform cross correlation to image fluid saturation in the subsurface based on Vp/Vs-ratio. The recently developed technique has been applied to estimate temporal changes of fluid distribution in fault zones and in volcanic regions but not yet in engineered geo-reservoirs. The improvement of the technology includes high-resolution waveform cross correlation applied to the high-quality datasets with lower magnitude of completeness resulting in a higher number of recorded events. The improvement allowed to estimate both, the spatial and temporal distribution of injected fluids and the state of the injected fluid during reservoir stimulation. Results of the DDW analysis revealed the development of an injection-derived steam plume during the early injection phase, particularly in the northern part of the Prati-32 study area.

15 GEOTHERMAL ENERGY↗

Fluctuations and Pinning for Individually Manipulated Skyrmions

We numerically examine the dynamics of individually dragged skyrmions interacting simultaneously with an array of other skyrmions and quenched disorder. For drives just above depinning, we observe a broadband noise signal with a 1/ f characteristic, while at higher drives, narrowband or white noise appears. Even in the absence of quenched disorder, the threshold force that must be applied to translate the driven skyrmion is finite due to elastic interactions with other skyrmions. The depinning threshold increases as the strength of the quenched disorder is raised. Above the depinning force, the skyrmion moves faster in the presence of quenched disorder than in a disorder-free system since the pinning sites prevent other skyrmions from being dragged along with the driven skyrmion. For strong pinning, we find a stick-slip motion of the driven skyrmion which produces a telegraph noise signature. The depinning threshold increases monotonically with skyrmion density in the absence of quenched disorder, but when pinning is present, the depinning threshold changes nonmonotonically with skyrmion density, and there are reentrant pinned phases due to a competition between pinning induced by the quenched disorder and that produced by the elastic interactions of the skyrmion lattice.

36 MATERIALS SCIENCE↗

Tectonics of the Outer Planet Satellites

Tectonic features on the satellites of the outer planets range from the familiar, such as clearly recognizable graben on many satellites, to the bizarre, such as the ubiquitous double ridges on Europa, the twisting sets of ridges on Triton, or the isolated giant mountains rising from Io's surface. All of the large and middle-sized outer planet satellites except Io are dominated by water ice near their surfaces. Though ice is a brittle material at the cold temperatures found in the outer solar system, the amount of energy it takes to bring it close to its melting point is lower than for a rocky body. Therefore, some unique features of icy satellite tectonics may be influenced by a near-surface ductile layer beneath the brittle surface material, and several of the icy satellites may possess subsurface oceans. Sources of stress to drive tectonism are commonly dominated by the tides that deform these satellites as they orbit their primary giant planets. On several satellites, the observed tectonic features may be the result of changes in their tidal figures, or motions of their solid surfaces with respect to their tidal figures. Other driving mechanisms for tectonics include volume changes due to ice or water phase changes in the interior, thermoelastic stress, deformation of the surface above rising diapirs of warm ice, and motion of subsurface material toward large impact basins as they fill in and relax. Most satellites exhibit evidence for extensional deformation, and some exhibit strike-slip faulting, whereas contractional tectonism appears to be rare. Io s surface is unique, exhibiting huge isolated mountains that may be blocks of crust tilting and foundering into the rapidly emptying interior as the surface is constantly buried by deposits from hyperactive volcanoes. Of the satellites, diminutive Enceladus is spectacularly active; its south polar terrain is a site of young tectonism, copious heat flow, and tall plumes venting into space. Europa's surface is pervasively tectonized, covered with a diverse array of exotic and incompletely understood tectonic features. The paucity of impact craters on Europa suggests that its tectonic activity is ongoing. Geysers on Triton show that some degree of current activity, while tectonic features that cross sparsely cratered terrain indicate that it may also be tectonically active. Ganymede and Miranda both exhibit ancient terrains that have been pulled apart by normal faulting. On Ganymede these faults form a global network, while they are confined to regional provinces on Miranda. Ariel, Dione, Tethys, Rhea, and Titania all have systems of normal faults cutting across their surfaces, though the rifting is less pronounced than it is on Ganymede and Miranda. Iapetus exhibits a giant equatorial ridge that has defied simple explanation. The rest of the large and middle-sized satellites show very little evidence for tectonic features on their surfaces, though the exploration of Titan's surface has just begun.

McKinnon, W. B.↗

3D X-ray Strain Microscopy in Two-Phase Composites at Submicron Length Scale

Author note: Part of this research summary is based on findings first reported in Refs. [3-5, 18]. Renewed interest in composite materials is driven by the fact that their mechanical properties can be superior to those of individual constituent phases. Interfaces between the phases are the key elements responsible for the unique micro-mechanisms of plastic deformation in composites. In this study the depth-dependent residual strain distributed in the two phases and partitioned across the composite interfaces is directly measured at submicron length-scale using X-ray microdiffraction and compared to a detailed simulation within the framework of micromechanical stress analysis. Interface strength is determined from the analysis of the so-called slip zone caused by the near-surface stress relaxation. Two examples are discussed including NiAl/Mo and Ni/Mo composites.

36 MATERIALS SCIENCE↗

Analysis of microstructural facet fatigue failure in ultra-fine grained powder metallurgy Ti-6Al-4V produced through hydrogen sintering

The hydrogen sintering and phase transformation (HSPT) process is a powder metallurgy method that produces Ti-6Al-4V with fatigue properties rivaling wrought processed Ti-6Al-4V. Previous fatigue work on HSPT Ti-6Al-4V has shown failure to be frequently caused by microstructural facets, which were believed to be grain boundary (GB) α phase. This belief conflicts with other reports as fatigue failure typically occurs across α colonies or primary α grains, not GB α. In this work, electron backscattered diffraction is used to identify these facets as GB α. Furthermore, a simple geometric model predicting the effective slip length of GB α is presented.

36 MATERIALS SCIENCE↗

Mesoscale crystal plasticity modeling of nanoscale Al–Al 2 Cu eutectic alloy

Nanolaminated composites composed of alternate metal and intermetallic or ceramic lamellae exhibit high strength, high strain hardening rate and measurable plasticity at ambient and elevated temperatures. Due to the difference in plastic deformation capability between the two phases, structural instability occurs in hard lamellae associated with buckling when a compression strain is applied parallel to the lamellae. Taking nanoscale Al–Al 2 Cu eutectic alloy as a model system, we develop a mesoscale crystal plasticity (CP) model based on the confined layer slip (CLS) mechanism (referred to as CLS-CP) to understand the buckling behavior of the nanolaminates. In the CLS-CP model, buckling in Al 2 Cu lamellae is constrained by the elastic-plastic deformation of Al lamellae. The critical resolved shear stress for dislocation slip in Al lamellae varies with layer thickness, estimated by the CLS mechanism. To capture the essential features of confined layer slip mechanism that dislocations propagate within the layer and are deposited at the interfaces, plastic deformation in each lamella is the same through the layer thickness. The variation of elastic deformation through the layer thickness is captured through dividing each Al lamella into three or more elements that have the same plastic deformation through the thickness. In comparison, we also conduct standard crystal plasticity modeling in which plastic deformation in the three elements through the layer thickness is calculated individually according to phenomenological power law. In these simulations, plasticity in Al 2 Cu lamellae is modeled with slips on {121} planes due to the slip continuity across the interface, which have been observed in our recent experiments. The CLS-CP model is able to predict mechanical properties of nano-scale lamellar materials. In contrast, the standard CP model is more suitable to study deformation behavior of sub-micro scale lamellar materials. In conclusion, the CLS-CP model calculations reveal that critical compression strain corresponding to buckling increases as layer thickness decreases, which agree with micro-pillar compression tests.

36 MATERIALS SCIENCE↗

Fifth-degree elastic energy for predictive continuum stress–strain relations and elastic instabilities under large strain and complex loading in silicon

Materials under complex loading develop large strains and often phase transformation via an elastic instability, as observed in both simple and complex systems. Here, we represent a material (exemplified for Si I) under large Lagrangian strains within a continuum description by a 5th-order elastic energy found by minimizing error relative to density functional theory (DFT) results. The Cauchy stress—Lagrangian strain curves for arbitrary complex loadings are in excellent correspondence with DFT results, including the elastic instability driving the Si I → II phase transformation (PT) and the shear instabilities. PT conditions for Si I → II under action of cubic axial stresses are linear in Cauchy stresses in agreement with DFT predictions. Such continuum elastic energy permits study of elastic instabilities and orientational dependence leading to different PTs, slip, twinning, or fracture, providing a fundamental basis for continuum physics simulations of crystal behavior under extreme loading.

36 MATERIALS SCIENCE↗

Phase field modeling of dislocations and obstacles in InSb

We present a phase-field dislocation dynamics (PFDD) model informed by first-principle calculations to elucidate the competitive dislocation nucleation and propagation between the glide and shuffle sets in InSb diamond cubic crystal. The calculations are directly informed with generalized stacking fault energy curves on the (111) slip plane for both the “glide set,” with the smaller interplanar spacing, and the “shuffle set,” with the larger interplanar spacing. The formulation also includes elastic anisotropy and the gradient term associated with the dislocation core. The PFDD calculations show that under no stress the equilibrium structure of screw glide set dislocations dissociates into Shockley partials, while those of the shuffle set dislocations do not dissociate, remaining compact. The calculated dislocation core widths of these InSb dislocations agree well with the measured values for other semiconductor materials, such as Si and GaN. We find that a shuffle set dislocation emits from a dislocation source at an applied stress about three times smaller than that needed to emit leading and trailing partials successively on the glide set plane. Once the partial dislocations in the glide set are emitted, they propagate faster than the shuffle set perfect dislocation at the same stress level.

36 MATERIALS SCIENCE↗

Fifth-degree elastic energy for predictive continuum stress-strain relations and elastic instabilities under large strain and complex loading in silicon

Materials under complex loading develop large strains and often phase transformation via an elastic instability, as observed in both simple and complex systems. Here, we represent a material (exemplified for Si I) under large Lagrangian strains within a continuum description by a 5th-order elastic energy found by minimizing error relative to density functional theory (DFT) results. The Cauchy stress—Lagrangian strain curves for arbitrary complex loadings are in excellent correspondence with DFT results, including the elastic instability driving the Si I → II phase transformation (PT) and the shear instabilities. PT conditions for Si I → II under action of cubic axial stresses are linear in Cauchy stresses in agreement with DFT predictions. Such continuum elastic energy permits study of elastic instabilities and orientational dependence leading to different PTs, slip, twinning, or fracture, providing a fundamental basis for continuum physics simulations of crystal behavior under extreme loading.

Levitas, Valery↗

Interaction of a normally-incident plane wave with a nonlinear poroelastic fracture

While it has been recognized that a large amplitude incident wave upon a dry fracture can exhibit nonlinear seismic wave scattering due to its stress-dependent mechanical compliance, the impact of pore fluid in the fracture and a fluid-filled poroelastic background medium—features common for fractures in the Earth—are not well understood. As a first step toward an understanding of the nonlinear poroelastic response of elastic waves in fractured media, analytical approximate formulas are used for the amplitude and phase of a normally incident plane wave using a perturbation method, assuming a fluid-filled, highly compliant nonlinear interface embedded in a linear poroelastic solid. The stress-closure behavior of the fracture is modeled by nonlinear, poroelastic displacement-discontinuity boundary conditions (a linear–slip interface). The theory predicts that the static (“Direct current,” or DC) and higher-order-harmonic waves produced by the nonlinear scattering can be greatly reduced by the presence of fluid in the fracture. This, however, depends upon a number of parameters, including fracture compliance, fluid properties (compressibility and viscosity), and the permeability of the background medium, as well as environmental parameters such as the initial fluid pressure and stress acting on the fracture. The static effect produces low-frequency fluid pressure pulses when a finite-duration wave is incident upon the fracture—behavior unique to fluid-filled fractures within a poroelastic medium.

58 GEOSCIENCES↗

Enhanced work hardening from oxygen-stabilized ω precipitates in an aged metastable β Ti-Nb alloy

High levels of oxygen in solid solution in Ti alloys are considered detrimental to mechanical properties because of embrittlement concerns. In metastable β titanium alloys, the formation of isothermal ω precipitates is also known to cause severe embrittlement and ductility reduction. However, oxygen has been shown to partition to the ω phase during ageing, and this partitioning behavior may potentially impact ω’s mechanical contribution. Using micropillar compression, we compared the deformation behavior of Ti-20Nb (at. %) with oxygen-stabilized ω precipitates to the behavior of oxygen-free specimens. The oxygen-stabilized microstructures showed increased compressive yield strength and enhanced work hardening behavior compared to oxygen-free specimens. In the absence of oxygen, the compressed pillars showed slip band formation and catastrophic failure, and transmission electron microscopy imaging revealed that ω precipitates were sheared within the continuous deformation channels resulting in slip localization. In contrast, oxygen-stabilized ω precipitates were harder to shear and the formation of continuous deformation channels was suppressed during compression, leading to improved work hardening behavior up to 15% strain. Furthermore, this counter-intuitive role of oxygen may offer design strategies to address the significant embrittlement and loss of ductility observed for ω-strengthened β Ti alloys without oxygen and avenues to expand the use of β Ti alloys.

36 MATERIALS SCIENCE↗

Novel shear mechanism in nanolayered composites

Recent studies have shown that two-phase nanocomposite materials with semicoherent interfaces exhibit enhanced strength, deformability, and radiation damage resistance. The remarkable behavior exhibited by these materials has been attributed to the atomistic structure of the bi-metal interface that results in interfaces with low shear strength and hence, strong barriers for slip transmission due to dislocation core spreading along the weak interfaces. In this work, the low interfacial shear strength of Cu/Nb nanoscale multilayers dictates a new mechanism for shear banding and strain softening during micropillar compression. Previous work investigating shear band formation in nanocrystalline materials has shown a connection between insufficient strain hardening and the onset of shear banding in Fe and Fe-10% Cu, but has also shown that hardening does not necessarily offset shear banding in Pd nanomaterials. Therefore, the mechanisms behind shear localization in nanocrystalline materials are not completely understood. Our findings, supported by molecular dynamics simulations, provide insight on the design of nanocomposites with tailored interface structures and geometry to obtain a combination of high strength and deformability. High strength is derived from the ability of the interfaces to trap dislocations through relative ease of interfacial shear, while deformability can be maximized by controlling the effects of loading geometry on shear band formation.

36 MATERIALS SCIENCE↗

Mechanochemical α to β phase transition of U 3 O 8

Recognized as the most stable phase of uranium oxide, α-U 3 O 8 is widely used throughout the nuclear fuel cycle for safe storage and transportation. There is, however, a lack of understanding of the thermodynamic relationship between α-U 3 O 8 and its polymorph, β-U 3 O 8 . This research contributes new knowledge regarding the kinetics and mechanism of a previously described mechanochemical phase transition between the α- and β-U 3 O 8 polymorphs to improve the understanding of their thermodynamic relationship. In this work, tumble milling of α-U 3 O 8 using different milling media shows an ingrowth of the β-phase over time, with an observed correlation between media density, percent conversion and lattice strain. Anisotropic peak broadening observed within collected X-ray diffraction powder patterns suggests the preservation of uranium polyhedral layered sheets throughout the milling process. Preservation of the sheets implies a shear-induced slip mechanism occurring through in-plane shifting of uranium polyhedra along lattice planes perpendicular to the polyhedral sheets.

Roach, Jordan M. [Oak Ridge National Laboratory (O↗

Journey to Time-Variable Moment Tensors through Inversion of Acoustic and Seismoacoustic Data

We explore the capability of acoustic and seismoacoustic datasets to directly resolve a complex, time-variable source consisting of a buried mechanism, represented as a moment tensor, and a spall mechanism, represented as a vertical force at the surface. Traditionally, each component of a resolved moment tensor assumes one underlying source time function, which likely fails to capture the full evolution of a dynamic source, such as an explosion followed by slip on near-source joints or development of spallation. Specifically, we expand previous work to resolve a time-variable moment tensor using single-modality and joint-modality inversion frameworks through analysis of infrasound and seismoacoustic data recorded as part of the Source Physics Experiment Phase II: Dry Alluvium Geology (DAG). We investigate the impact of including signals from seismic-to-air coupling that are local to each infrasound sensor in comparison to mainly atmosphere-propagating acoustic signals, which occur from coupling of the wavefield from the subsurface to the atmosphere directly above the source. Additionally, we assess the ability of our inversion algorithm to fit observed infrasound data using a variety of time-variable source mechanisms. First, we consider the buried moment tensor source alone, which assumes that the determined Green’s functions incorporate effects from spallation or that the impact from spallation is minimal. Second, we examine the estimated buried moment tensor and vertical surface spallation as terms that must both be resolved in the inversion. Third, we assess the ability for an estimated vertical surface spallation source to fit the acoustic data on its own. Finally, we compare results from the joint inversion of both seismic geophone and infrasound acoustic data for the buried-only source compared to buried and spallation sources. Our results are a preliminary investigation into the applications of the inversion technique to recorded datasets and show the technique has limited capabilities using acoustic data alone. Instead, this method shows promise for seismic and seismoacoustic datasets to resolve the time-variable mechanisms of a buried source.

47 OTHER INSTRUMENTATION↗

Application of a Multiscale Model of Tantalum Deformation at Megabar Pressures

A new multiscale simulation tool has been developed to model the strength of tantalum under high-pressure dynamic compression. This new model combines simulations at multiple length scales to explain macroscopic properties of materials. Previously known continuum models of material response under load have built upon a mixture of theoretical physics and experimental phenomenology. Experimental data, typically measured at static pressures, are used as a means of calibration to construct models that parameterize the material properties; e.g., yield stress, work hardening, strain-rate dependence, etc. The pressure dependence for most models enters through the shear modulus, which is used to scale the flow stress. When these models are applied to data taken far outside the calibrated regions of phase space (e.g., strain rate or pressure) they often diverge in their predicted behavior of material deformation. The new multiscale model, developed at Lawrence Livermore National Laboratory, starts with interatomic quantum mechanical potential and is based on the motion and multiplication of dislocations. The basis for the macroscale model is plastic deformation by phonon drag and thermally activated dislocation motion and strain hardening resulting from elastic interactions among dislocations. The dislocation density, {rho}, and dislocation velocity, {nu}, are connected to the plastic strain rate {var_epsilon}{sup p}, via Orowan's equation: {var_epsilon}{sup p} = {rho}b{nu}/M, where b is the Burger's vector, the shear magnitude associated with a dislocation, and M is the Taylor factor, which accounts for geometric effects in how slip systems accommodate the deformation. The evolution of the dislocation density and velocity is carried out in the continuum model by parameterized fits to smaller scale simulations, each informed by calculations on smaller length scales down to atomistic dimensions. We apply this new model for tantalum to two sets of experiments and compare the results with more traditional models. The experiments are based on the Barnes's technique in which a low density material loads against a metal surface containing a pre-imposed rippled pattern. The loaded sample is Rayleigh-Taylor unstable and the rippled amplitudes grow with time. The rate of growth differs depending on the material strength, with stronger materials growing less, even to the point of saturation. One set of experiments was conducted at the pRad facility at LANSCE at Los Alamos National Laboratory in 2007 using high-explosive (HE) driven tantalum samples. The other set of experiments was done at the Omega laser at the Laboratory for Laser Energetics at the University of Rochester, which used high-powered lasers to create plasmas to dynamically compress a rippled tantalum sample. The two techniques provide data at different pressures and strain rates: The HE technique drives the samples at around 2 x 10{sup 5} s{sup -1} strain rate and pressures near 500 kbar, while the laser technique hits strain rates around 2 x 10{sup 7} s{sup -1} and pressures close to 1.4 Mbar. The most recent laser experiments were conducted in February 2010 and they present a sample of the data in Figure 1, which shows a face-on radiograph at a time of 65 ns after the laser was turned on. From this radiograph, they measure the growth factor which is defined to be the change in amplitude of the ripples relative to their initial amplitude. Figure 2 shows the resulting growth factors along with various model fits. The error bars are typically 20-25%. Only the multiscale model predictions match the experimental measurements. The growth factors via the HE technique are determined from multiple side-on proton radiography images and thus provide a full growth curve per single experiment. A sample growth curve is shown in Figure 3, also with various model fits and error bars estimated at 25%. It should be noted that by 7.5 {micro}s the growth in this sample has exceeded the initial target thickness indicating that localizations not captured in the overall simulation have probably become dominant, i.e., the target is likely breaking up. Application of the multiscale dislocation dynamics model as implemented in the Ares hydrodynamics code shows excellent agreement with both the pRad and Omega data. They also compare the Steinberg-Lund (SL), Preston-Tonks-Wallace (PTW), and Stainberg-Guinan (SG) models with the data. The PTW and SG models provide good fits to the pRad data but over-predict the growth (underestimate the strength) on the laser platform. The SL model under-predicts the pRad data and over-predicts the Omega data. The excellent agreement of the multiscale model with the data over two orders of magnitude in strain rate and more than a factor of two in pressure lends credibility to the model. They continue to stress the model by conducting experiments at 5 Mbars and beyond at the National Ignition Facility at LLNL in the near future.

36 MATERIALS SCIENCE↗

Complementary use of monochromatic and white-beam X-ray micro-diffraction for the investigation of ancient materials

Archaeological artefacts are often heterogeneous materials where several phases coexist in a wide grain size distribution. Most of the time, retrieving structure information at the micrometre scale is of great importance for these materials. Particularly, the organization of different phases at the micrometre scale is closely related to optical or mechanical properties, manufacturing processes, functionalities in ancient times and long-term conservation. Between classic X-ray powder diffraction with a millimetre beam and transmission electron microscopy, a gap exists and structure and phase information at the micrometre scale are missing. Using a micrometre-size synchrotron X-ray beam, a hybrid approach combining both monochromatic powder micro-diffraction and Laue single-crystal micro-diffraction was deployed to obtain information from nanometre- and micrometre-size phases, respectively. Therefore providing a way to bridge the aforementioned gap, this unique methodology was applied to three different types of ancient materials that all show a strong heterogeneity. In Roman terra sigillata, the specific distribution of nanocrystalline hematite is mainly responsible for the deep-red tone of the slip, while the distribution of micrometre-size quartz in ceramic bodies reflects the change of manufacturing process between pre-sigillata and high-quality sigillata periods. In the second example, we investigated the modifications occurring in Neolithic and geological flints after a heating process. By separating the diffracted signal coming from the nano- and the micrometre scale, we observed a domain size increase for nanocrystalline quartz in geological flints and a relaxation of the residual strain in larger detritic quartz. In conclusion, through the study of a Roman iron nail, we showed that the carburation process to strengthen the steel was mainly a surface process that formed 10–20 µm size domains of single–crystal ferrite and nanocrystalline cementite.

36 MATERIALS SCIENCE↗

Carrier and symbol synchronization system performance study

Results pertinent to predicting the performance of convolutionally encoded binary phase-shift keyed communication links were presented. The details of the development are provided in four sections. These sections are concerned with developing the bit error probability performance degradations due to PN despreading by a time-shared delay locked loop, the Costas demodulation process, symbol synchronization effects and cycle slipping phenomena in the Costas loop. In addition, Costas cycle slipping probabilities are studied as functions of Doppler count time and signal-to-noise conditions. The effect of cycle slipping in the symbol synchronizer is also studied as a function of channel Doppler and other frequency uncertainties.

Lindsey, W. C.↗

The Plunge Phase of Friction Stir Welding

The many advantages of Friction Stir Welding have led to a relatively rapid acceptance in the often conservative welding community. Because the process is so different from traditional fusion welding, with which most investigators are most familiar, there remain many aspects of FSW for which there is no clear consensus. For example, the well known onion rings seen in transverse sections have been variously interpreted as grain size variations, variation in density of second phase particles and parts of the carousel of material rotating with the pin that have been shed from the carousel. Using Orientation Imaging Microscopy, Schneider has recently noted that the onion rings have a different orientation (and hence etch differently) than the surrounding material, and this orientation is consistent with slip plane orientations at the edge of the carousel. Likewise, the forces and torque exerted by the FSW tool on the work piece largely remain unaccounted for. Although these forces are routinely measured by investigators with commercial instrumented welders, they are rarely reported or even qualitatively analyzed. This paper will introduce a model based on a carousel or disk of material that rotates with the tool to estimate the torque and plunge force required to plunge a tool into the work piece. A stationary tool is modeled rather than the moving tool because effects such as thermal transients and metallurgical changes in the sample (primarily aging in aluminum) can be more easily accounted for. It is believed, however, that with some modifications the model should be applicable to a moving tool also.

McClure, John C.↗