Results for “Post-flight Data” — Page 26

NASA NTRSDate not supplied

Space Launch System Artemis I Ascent Loads Reconstruction Summary

On November 16, 2022, NASA successfully launched the Space Launch System (SLS) rocket and Orion spacecraft for the first SLS mission, Artemis 1. This first flight was outfitted with Developmental Flight Instrumentation (DFI) such as accelerometers, pressure sensors, and strain gauges. The DFI supports many post-flight activities, one of which is the ascent loads reconstruction effort. The integrated vehicle ascent loads spans both boost phase and Core phase and often produces the largest loads experienced by the vehicle during flight. One of the primary goals of the ascent loads reconstruction is to evaluate applicable Coupled Loads Analysis (CLA) design math models, assumptions, and analysis methodologies. To achieve this goal, all significant ascent subevents have been reconstructed through the use of flight data, reconstructed inputs, and existing CLA simulations. Resulting responses have been compared to available flight measurements. Additionally, reconstructed subevent loads were combined and compared to appropriate flight data and pre-flight predictions.

SLS↗

NASA NTRSDate not supplied

Comparison of Pre- and Post-Flight Estimations of Pitch Damping Coefficients for Unguided Entry Vehicles

Pre-flight predictions of pitch damping coefficient (C M q + C m ȧ ) curves are used in entry simulations to determine flight readiness and if any dynamic remediation strategies are required. Accurate characterization of these pitch damping coefficient curves is crucial for mission success. Historically, pre-flight estimations of these curves are derived experimentally either via ballistic range testing or with 1-degree-of-freedom (DOF) free-or forced-oscillation wind tunnel testing. With post-flight best-estimated trajectories, a fitting procedure as described in Karlgaard, et. al. is used to compare pre-and post-flight pitch damping coefficients. This technique relies on an assumed analytical form of the trajectory, a limited 3-DOF representation described in Schoenenberger and Queen, which results in an Euler-Cauchy solution form. This solution assumes constant density, thus limited amplitude multi-peak windows of the trajectory are considered to populate the pitch damping-amplitudes pace. The estimated post-flight pitch damping approximations and the pre-flight predictions shown are effective representations of pitch damping, or the integrated effect of the pitch damping coefficient over one pitch cycle at the corresponding cycle’s peak amplitude. Effective pitch damping coefficient curves provide more intuitive insights about where the vehicle is stable and permits readily processed comparisons between data-sets. It is important to note that most pitch damping curves, such as those reported in aero databases and utilized in flight mechanics trajectory simulations, are represented in instantaneous angle-of-attack space distinct from what is presented in the paper.

pitch damping coefficient↗

NASA NTRSDate not supplied

Design and Technology Maturation of the Stratospheric Projectile Experiment of Entry Dynamics

The supersonic and transonic dynamic stability of blunt-body reentry vehicles currently poses large risks in all of NASA’s ongoing entry missions (MSR SRL, MSR EES, and Dragonfly). These projects have allocated millions of dollars to testing and modeling efforts to buy down risk by using the current state-of-the-art (SoA) facilities at NASA’s disposal. While these facilities have heritage in supplying dynamics data to reentry missions, their availability is severely limited – particularly with the high number of concur-rent projects requesting simultaneous testing– and are costly when considering the science density per dollar. None of the current SoA facility methodologies allow the test model to have the dynamics fully develop through a flight relevant free-stream profile and as such require extrapolations with resultant high uncertainties in order to relate the test dynamics to flight expectations. SPEED is a NASA Ames Center Innovation Fund (CIF) project that is developing a highly tailorable and cost-effective test methodology to better assess the dynamic stability of blunt-body reentry vehicles via a stratospheric balloon flight. This is accomplished by dropping a suite of instrumented capsules from a stratospheric balloon to gain a statistically relevant dataset of scaled reentry vehicles in mission relevant free-flight conditions. This presentation will walk through how the test methodology is being implemented specifically for the Mars Sample Return (MSR) Earth Entry System (EES) geometry in an awarded Flight Opportunities Program (FOP) test flight in early CY24. SPEED Application to MSR: SPEED consists of three main mechanical systems: the Drop Platform, the Projectile, and the test Capsule. SPEED is being developed as a set of guidelines and recommendations for how to test with the proposed Concept of Operations (Conops) since the specific design parameters will vary depending on the specific project’s reference trajectory and entry vehicle design. As such, this presentation will walk through the development time-line as shown in Fig. 2. This is meant to serve as a blueprint for further missions as desired. Mechanical and Avionics Design. The SPEED test platform designed for the MSR-EES capsule geometry with nominal entry parameters has the ability to carry 10 Capsules to altitude instrumented with: 1. 3-Axis Accelerometer 2. IMU 3. Gyroscope 4. Magnetometer 5. Pressure Transducer cruciform 6. Uplook and Horizon Cameras To package the avionics/instrumentation suite, the capsule is approximately 1’ in diameter with the Outer Mold Line (OML) centroid-scaled from the full EES design. The internal volume is gutted and custom-shaped to fit the desired instrumentation suite, as well as to allow for the positioning of ballast mass such that the Center of Gravity is analogous to the flight vehicle. All structural components in the Capsule and Projectile are 3D printed, which significantly reduces the cost of each flight unit to around $1500 including all instrumentation, avionics, and structural components. Flight Conops. The test Capsule is accelerated to the desired altitude and Mach number while stowed in the Projectile, a missile-like vehicle consisting of steel ballast in the nose, a low-drag OML, and an Ejection Mechanism to reliably release the Capsule into the free-flow supersonic conditions. For the MSR-EES design, the capsule employs ~3kg of ballast mass at the nose to accelerate the 1.25kg test Capsule to ~Mach 1.7 at 23km altitude. This requires an initial release altitude of 40km, the quoted limit of a 80kg payload by the FOP-contracted balloon provider. Once the Ejection Mechanism avionics detect the proper conditions, the spring-loaded Ejection Mechanism will release and – guided by the sabot – expose the test Capsule to the desired test conditions for ~5 seconds of free-flight in the supersonic/transonic regimes. Dynamics in the subsonic regime will also be captured with the instrumentation suite with post-flight recovery operations aimed at recovering the high-G-load capable SD cards after the planned hard impact landings. Testing and Development: In the few months the SPEED project has worked the development of MSR-EES flight test, the team has performed lab and drone based testing which this presentation will overview. After the first design phase, the team fabricated Engineering Demonstration Units (EDUs) of all subsystems to perform validation testing shown in Fig. 5. After validation was completed on the subsystem level, a drone-drop test was performed at the recreational flight ceiling of 400ft altitude to assess the SPEED systems in a flight environment. Parameters such as in-flight stability, hard impact landing performance, and avionics performance were quantified and qualified. The FY23 CIF will culminate in a helicopter drop test aboard an Air National Guard Blackhawk. This will prepare the team for the CY24 FOP stratospheric balloon flight that should provide the final verification to begin offering the test platform for mission support. Focus of Presentation: This presentation will outline the technology maturation path of the SPEED implementation to the MSR-EES capsule baseline as well as the details regarding the mechanical system, avionics and instrumentation, and flight operations. Note that a complementary presentation is being submitted for a methodology overview of the SPEED test platform, introducing the testing technique and benefits as well as the full application space of the technology.

pitch damping coefficient↗

NASA NTRSDate not supplied

Rediscovering Apollo Biomedical Data to Support Artemis: The Apollo Records Synthesis Project

With the first crewed missions of the Artemis Program on the horizon, including the return of humans to another planetary surface, the space medicine and research communities have a renewed interest in buying down risk on these missions using historic Apollo datasets. Archivists with NASA’s Life Sciences Data Archive (LSDA) and epidemiologists with the Lifetime Surveillance of Astronaut Health (LSAH) are collaborating on a project aiming at improving access to historic datasets from the Apollo Program. The Apollo Records Synthesis Project (ARSP) seeks to expand the available historic biomedical knowledge base by examining physical records located across a wide range of collections, including examples such as pre-flight and post-flight physicals, lab reports, and handwritten flight surgeon and biomedical engineer logs from Apollo missions. The ARSP team has been able to identify several previously undocumented sources of biomedical information from Apollo missions. In the future, the team will modernize record storage and accessibility of these resources using digitization and natural language processing. This poster will discuss the progress of the project, give context to the dual research-clinical care nature of the records, and highlight the challenges and opportunities in using data from historical records. This poster will also provide information on how researchers can request access to datasets from these records.

life sciences↗

NASA NTRSDate not supplied

The NASA JSC Hypervelocity Impact Technology (HVIT) Office

The Hypervelocity Impact Technology (HVIT) office at the National Aeronautical and Space Administration (NASA) Johnson Space Center (JSC) is dedicated to support NASA flight programs in meeting their meteoroid and orbital debris (MMOD) protection requirements both efficiently and effectively, with a minimum of shielding mass, volume, and cost. This paper provides an overview of HVIT capabilities in providing hypervelocity tests, analyses, MMOD risk assessments and shielding expertise. HVIT personnel work closely with NASA program and safety/mission assurance personnel to develop program-specific MMOD protection requirements which are both achievable based on initial risk assessments and will meet overall safety and mission success requirements. HVIT then proceeds with hypervelocity impact testing and hydrocode assessments to update and verify ballistic limit equations used in the MMOD risk assessment. Hypervelocity impact tests are primarily performed at the NASA WSTF Remote Hypervelocity Test Laboratory (RHTL). Other hypervelocity facilities that provide complementary test capabilities are called on when necessary to fill data gaps. The goal of the final pre-flight MMOD risk assessment is to show compliance with MMOD requirements prior to flight. This final assessment will also incorporate changes in the MMOD environment from meteoroid showers and orbital debris breakups. After the mission is flown, post-flight inspections are performed by HVIT to document and trend MMOD damage to returned spacecraft surfaces and hardware. HVIT accomplishments in NASA mission support are described. In addition, current HVIT activities to aid on-going NASA crewed missions and science missions are presented.

Meteoroid↗

NASA NTRS2024

Flow Cytometry Methods to Monitor Immune System Dysregulation in Astronauts

Persistent immune system dysregulation has been documented to occur in astronauts participating in orbital spaceflight onboard the International Space Station. The phenomenon consists of reductions in T and NK cell function, altered cytokine profiles, persistent inflammation, and the subclinical reactivation of latent herpesviruses. In select crewmembers the dysregulation does actually lead to clinical symptoms, primarily atypical allergy or atopic dermatitis/zoster. Flow cytometry has served a central role defining the ‘immune assessment’ panel of assays that allow monitoring of astronauts. The cytometry assays which have been utilized include: 1. Peripheral leukocyte subsets 2. T cell function 3. Monocyte function 4. NK cell function 5. Intracellular cytokine analysis 6. Virus-specific T cell number (tetramer assay) 7. Virus-specific T cell function (peptide stimulation) 8. Leukocyte-bacterial challenge cytometry 9. Cytometric bead/multiplex array (soluble proteins) The use of these assays has been validated through various ISS flight investigations to define, to varying degrees, both in-flight, and post-flight immune system alterations. The kinetics of the dysregulation through the various phases of spaceflight, as well as post-flight recovery, have also been documented. To allow the science to occur within the orbital constraints of a spaceflight investigation, particular sample collection and processing techniques were developed compatible with the delays associated with terrestrial processing of in-flight samples. A subset of the assays has been adapted to routine monitoring of astronauts via a NASA ‘ISS Standard Measures’ activity, with the data from a specific crew then provided to all science investigators for that particular mission. This battery of cytometry assays has also been applied, through ground investigations, to several terrestrial ‘spaceflight analog’ populations. The purpose was to validate the analog which most closely replicates the in-flight observed pattern of alterations, generally believed to be winterover at an Antarctica station. To assist in determination of clinical risk, the assay panel has also been applied to investigations of various terrestrial patient populations, particularly zoster patients. As NASA is initiating crewed lunar missions via the ‘Artemis’ program, deployment of a miniaturized, microgravity-compatible flow cytometer, would be extremely beneficial to allow real time monitoring of crewmembers. Real time medical data could influence use of several countermeasures options during deep space missions. Several such instruments have been developed and validated to varying degrees of success. Assay details and summary findings across the various flight and ground platforms will be presented, as will current status in developing such technology for in-flight use.

Brian Crucian↗

NASA NTRSDate not supplied

Space Launch System Base Aerothermodynamics Post-Flight Reconstruction for Artemis I

Artemis I was the first uncrewed integrated test flight of the NASA heavy-lift, human-rated, exploration-class launch vehicle, Space Launch System (SLS), and Orion spacecraft. Artemis I successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2023. The integrated test flight is composed of launch and ascent of the SLS vehicle from lift-off to RS-25 main engine cut-off (MECO), interim cryogenic propulsion stage (ICPS) in-space flight and Orion’s trajectory around the moon and landing in the Pacific Ocean which occurred on December 11th, 2023. The SLS total thrust of 8,800,000 lbf is powered by four LOX/LH2 RS-25 engines and two 5-segment solid rocket boosters. As a result, base flow environments for this vehicle are highly complex and extreme. SLS base aerothermodynamics covers rocket plume-induced convection and radiation of the vehicle’s aft region during powered flight from lift-off to MECO. This work discusses the SLS base flow physics observed during Artemis I and comparisons of post-flight reconstruction with pre-flight models and Space Shuttle data. This is the first time in-depth base heating flight reconstruction has been investigated for an exploration-class launch vehicle since the Saturn V Program.

aerothermodynamics↗

NASA NTRSDate not supplied

Post-Flight Aerodynamics Assessment of the Artemis-I Booster Separation Event

The successful launch of the Artemis-I mission in November 2022 was made possible, in part, by years of rigorous vehicle simulation and scaled testing. Correctly anticipating the complex physics of the booster separation event was one of many necessary challenges. The successful booster separation of Artemis-I yielded flight data with which the fidelity of these predictions could be assessed. In this paper, the flight data and flight simulations are reconciled to present a unified assessment of the booster separation event. With this assessment, predictive confidence can be reinforced in support of the crewed Artemis-II mission.

Michael W Lee↗

NASA NTRSDate not supplied

Tracking and Recovery of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Reentry Vehicle (RV)

The LOFTID mission launched from Vandenberg on Nov 10, 2022, and successfully demonstrated the reentry of a 6m diameter inflatable aeroshell from low Earth orbit. This paper will cover the design features implemented to enable recovery of the flight vehicle, and will discuss the splashdown calculations, in-flight tracking, recovery from the ocean, and post-flight inspection of the flight vehicle. To support recovery of the RV and ejected data recorder after splashdown, a recovery ship was pre-positioned near the predicted splashdown ellipse in the Pacific Ocean. The splashdown ellipse was repeatedly updated as launch approached. In-flight tracking included transmission from the RV of GPS data through both the Iridium satellite network and the LoRa direct RF link, along with IR video cameras on the recovery ship and airborne imagery from the SCIFLI Team. Using both the GPS data and the IR imagery, the recovery ship tracked down the RV, and deployed an inflatable boat to approach the RV and attach it to the ship’s crane, after which the RV was hoisted on board and secured in its GSE recovery stand. The ship then tracked down the ejected data recorder, which was also broadcasting its GPS data, and pulled it from the water. Once the ship returned to port, the RV was hoisted ashore for additional inspection, removal of the data recorders, and repackaging for shipment back to NASA Langley.

Robert A. Dillman↗

NASA NTRSDate not supplied

Post-Flight Aerodynamics Assessment of the Artemis-I Booster Separation Event

The successful launch of the Artemis-I mission in November 2022 was made possible, in part, by years of rigorous vehicle simulation and scaled testing. Correctly anticipating the complex physics of the booster separation event was one of many necessary challenges. The successful booster separation of Artemis-I yielded flight data with which the fidelity of these predictions could be assessed. In this paper, the flight data and flight simulations are reconciled to present a unified assessment of the booster separation event. With this assessment, predictive confidence can be reinforced in support of the crewed Artemis-II mission.

Michael Lee↗

NASA NTRSDate not supplied

Space Launch System Base Aerothermodynamics Post-Flight Reconstruction for Artemis I

Artemis I was the first uncrewed integrated test flight of the NASA heavy-lift, human-rated, exploration-class launch vehicle, Space Launch System (SLS), and Orion spacecraft. Artemis I successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2023. The integrated test flight is composed of launch and ascent of the SLS vehicle from lift-off to RS-25 main engine cut-off (MECO), interim cryogenic propulsion stage (ICPS) in-space flight and Orion’s trajectory around the moon and landing in the Pacific Ocean which occurred on December 11th, 2023. The SLS total thrust of 8,800,000 lbf is powered by four LOX/LH2 RS-25 engines and two 5-segment solid rocket boosters. As a result, base flow environments for this vehicle are highly complex and extreme. SLS base aerothermodynamics covers rocket plume-induced convection and radiation of the vehicle’s aft region during powered flight from lift-off to MECO. This work discusses the SLS base flow physics observed during Artemis I and comparisons of post-flight reconstruction with pre-flight models and Space Shuttle data. This is the first time in-depth base heating flight reconstruction has been investigated for an exploration-class launch vehicle since the Saturn V Program.

aerothermodynamics↗

NASA NTRSDate not supplied

Base Aerodynamics Post-Flight Reconstruction for Artemis I

Artemis I was the first uncrewed integrated test flight of the NASA heavy-lift, human-rated, exploration-class launch vehicle, Space Launch System (SLS), and Orion spacecraft. Artemis I successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2022. The integrated test flight was composed of launch and ascent of SLS vehicle from lift-off to RS-25 main engine cut-off (MECO), interim cryogenic propulsion stage (ICPS) in-space flight and Orion’s trajectory around the moon and landing in the Pacific Ocean which occurred on December 11th, 2022. The SLS total thrust of 8,800,000 lbf was powered by four LOX/LH2 RS-25 engines and two 5-segment solid rocket boosters. As a result, the base flow field had highly complex phenomena and regimes. SLS base aerodynamics covers vehicle base pressure and integrated axial force during powered flight from lift-off to MECO. This work discusses the SLS base flow physics observed during Artemis I and comparisons of post-flight reconstruction with pre-flight models and Space Shuttle data. This was the first time in-depth base aerodynamics flight reconstruction has been investigated for an exploration-class launch vehicle since the Saturn V Program.

aerothermodynamics↗

NASA NTRSDate not supplied

Tracking and Recovery of the LOFTID RV (Low-Earth Orbit Flight Test of an Inflatable Decelerator Reentry Vehicle)

The LOFTID mission launched from Vandenberg on Nov 10, 2022, and successfully demonstrated the reentry of a 6m diameter inflatable aeroshell from low Earth orbit. This paper will cover the design features implemented to enable recovery of the flight vehicle, and will discuss the splashdown calculations, in-flight tracking, recovery from the ocean, and post-flight inspection of the flight vehicle. To support recovery of the RV and ejected data recorder after splashdown, a recovery ship was pre-positioned near the predicted splashdown ellipse in the Pacific Ocean. The splashdown ellipse was repeatedly updated as launch approached. In-flight tracking included transmission from the RV of GPS data through both the Iridium satellite network and the LoRa direct RF link, along with IR video cameras on the recovery ship and airborne imagery from the SCIFLI Team. Using both the GPS data and the IR imagery, the recovery ship tracked down the RV, and deployed an inflatable boat to approach the RV and attach it to the ship’s crane, after which the RV was hoisted on board and secured in its GSE recovery stand. The ship then tracked down the ejected data recorder, which was also broadcasting its GPS data, and pulled it from the water. Once the ship returned to port, the RV was hoisted ashore for additional inspection, removal of the data recorders, and repackaging for shipment back to NASA Langley.

Robert A Dillman↗

NASA NTRS2024

Analyses of the MISSE 9-15 Polymers and Composites Experiment 1-4 (PCE 1-4) Contamination Samples

Spacecraft in low Earth orbit (LEO) are subjected to harsh environmental conditions, including radiation (cosmic rays, ultraviolet (UV), x-ray and charged particle radiation), micrometeoroids and orbital debris, temperature extremes, thermal cycling, and atomic oxygen (AO). These environmental exposures can result in erosion, embrittlement and optical property degradation of susceptible materials threatening spacecraft performance and durability. To increase our understanding of environmental effects such as AO erosion and radiation induced embrittlement of spacecraft materials, NASA Glenn Research Center developed a series of experiments that were flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). Recently, four Glenn experiments with 365 flight samples were flown on ISS’s MISSE-Flight Facility (MISSE-FF). These experiments are the Polymers and Composites Experiment-1 (PCE-1) flown as part of the MISSE-9 mission, the PCE-2 flown as part of the MISSE-10 mission, the PCE-3 flown as part of the MISSE-12 and MISSE-15 missions, and the PCE-4 flown as part of the MISSE-13 mission. Each of these experiments included passive contamination witness samples in each flight direction for post-flight molecular contamination analyses. A total of 13 contamination flight samples were flown. The post-flight analyses of the PCE 1-4 contamination samples include X-ray Photoelectron Spectroscopy (XPS) analyses (surface and ion sputter depth analyses) and optical properties (total reflectance, total transmittance and solar absorptance). This paper provides results of post-flight analyses of the PCE 1-4 contamination samples and their corresponding control samples. Knowledge of on-orbit contamination is important for the PCE 1-4 flight data interpretation.

Atomic Oxygen↗

NASA NTRS2024

Rediscovering Apollo Biomedical Data to Support Artemis: The Apollo Records Synthesis Project

With the first crewed missions of the Artemis Program on the horizon, including the return of humans to another planetary surface, the space medicine and research communities have a renewed interest in buying down risk on these missions using historic Apollo datasets. Archivists with NASA’s Life Sciences Data Archive (LSDA) and epidemiologists with the Lifetime Surveillance of Astronaut Health (LSAH) are collaborating on a project aiming at improving access to historic datasets from the Apollo Program. The Apollo Records Synthesis Project (ARSP) seeks to expand the available historic biomedical knowledge base by examining physical records located across a wide range of collections, including examples such as pre-flight and post-flight physicals, lab reports, and handwritten flight surgeon and biomedical engineer logs from Apollo missions. The ARSP team has been able to identify several previously undocumented sources of biomedical information from Apollo missions. In the future, the team will modernize record storage and accessibility of these resources using digitization and natural language processing. This poster will discuss the progress of the project, give context to the dual research-clinical care nature of the records, and highlight the challenges and opportunities in using data from historical records. This poster will also provide information on how researchers can request access to datasets from these records.

life sciences↗

NASA NTRSDate not supplied

Long-Term Health Metric Development Effort

INTRODUCTION Probabilistic Risk Assessment (PRA) is a methodology applied when high-stakes decisions need to be made about complex systems. PRA often uses risk minimization to aid decision making, such as when establishing vehicle requirements or resource allocations. The NASA Human System Risk Board (HSRB) maintains the human spaceflight risk postures, many of which have in-mission medical outcomes, but the full risk set also includes performance and Long-Term Health (LTH) outcomes. An effort is underway to determine the dependencies between LTH risk outcomes and mission characteristics and to identify metrics for quantifying LTH outcomes. The LTH metrics will be incorporated into future PRA tools currently under development to support crew health and performance decision making. LONG-TERM HEALTH (LTH) RISK LTH risk encompasses the timeframe from immediately post-flight, through the rest of an astronaut’s career, through retirement, and until death. LTH outcomes include the time and interventions needed for the astronaut to return to preflight physiological states after experiencing spaceflight hazards and recovery from any in-mission medical events that persist into the post-flight timeframe. It includes chronic complications that may arise due to experiencing in-flight medical conditions or injuries and medical conditions that occur later in life with a higher probability of occurrence or with more severity because of their spaceflight exposure. Finally, LTH outcomes can also include a reduction in life expectancy due to spaceflight exposures. Eighteen of the HSRB risks contain an LTH component, each with a unique incidence rate and consequence severity. ON-GOING LTH METRIC DEVELOPMENT EFFORTS Based on guidance from a stakeholder workshop held on June 1, 2023, only LTH outcomes with causes tied to spaceflight experience that are significantly different from normal healthy aging and which can be affected by changes in in-mission resources are targeted for inclusion within the PRA modeling efforts. Current on-going efforts include a sensitivity analysis of potential in-flight medical conditions to determine which conditions may persist into post-flight and how the consequences may be affected by in-mission medical resources. Also underway is determination of differences in the time for a return to preflight physiological baselines when in-flight countermeasures are available versus when they are not. Analyses performed with publicly available astronaut data and collaborations with the Lifetime Surveillance of Astronaut Health team are being designed to understand which LTH outcomes differ significantly from natural healthy aging. Information exchanges are also occurring with LTH risk custodians to understand how they quantify outcomes. FUTURE PLANS Risk characteristics will be determined for each LTH risk that meets our inclusion criteria and the dependencies of their outcomes to in-mission resources and mission characteristics will be established. The individual risks will be integrated together into one or more high level LTH metrics for inclusion in the PRA tool, so that LTH risks can be considered along with in-mission risks during crew health and performance system decision support trade studies.

B. E. Lewandowski↗

NASA NTRSDate not supplied

Testing a Run-Time Assurance Framework Coupled with Integrated Risk Mitigation Capabilities for Autonomous Urban UAS Flights

The In-Time Aviation Safety Management System (IASMS) Concept of Operations (ConOps) envisions new capabilities to monitor, assess, and mitigate flight safety risks. Systems will be tailored to mission type, vehicle/equipage type, operational environment, and safety risk tolerance. Within an IASMS framework, several capabilities may be implemented spanning three operational phases (pre-flight, in-flight, and post-flight/off-line); and consisting of lower level functions and information services which may reside onboard the aircraft, on third-party server(s), and/or on ground/operator station(s). Each capability will be designed to produce and disseminate safety-relevant information; perform detection, diagnosis, and prediction of unsafe situations; and/or execute mitigation actions when hazardous events warrant such changes. This paper focuses on recent testing of airborne capabilities that demonstrate inflight aspects of the overarching concept for autonomous unmanned aircraft systems (UAS) operations in urban environments. A flight test architecture is described that applies run-time assurance principles (e.g., executes independent of the unassured autopilot), real-time risk assessment, and a technique to execute contingencies if necessary either automatically or via pilot intervention. Several tests using small UAS were conducted to verify the assured in-flight risk mitigation capability. The paper draws significantly from a larger NASA technical report and recent prior conference papers, providing additional details. Data is analyzed for two representative flights to illustrate the performance for various sequential and simultaneous hazards used during testing. During each automated flight, several hazards are encountered at various points along the flight path. At each point, the hazard is mitigated by the system, with the vehicle then continuing to subsequent points. The paper concludes with lessons-learned regarding relevant aspects of the overarching IASMS concept and how it may be updated and further advanced in the future.

population activity↗

NASA NTRSDate not supplied

Overview of Results from the MISSE 9-15 Polymers and Composites Experiment 1-4 (PCE 1-4)

Spacecraft in low Earth orbit (LEO) and other planetary orbits are subjected to harsh environmental conditions that can result in erosion, embrittlement and optical property degradation of susceptible materials threatening spacecraft performance and durability. To increase our understanding of space environmental effects on spacecraft materials, NASA Glenn Research Center has developed a series of experiments flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). Four Glenn experiments with 365 flight samples were flown on ISS’s MISSE-Flight Facility (MISSE-FF). These experiments are the Polymers and Composites Experiment-1 (PCE-1) flown as part of the MISSE-9 mission, the PCE-2 flown as part of the MISSE-10 mission, the PCE-3 flown as part of the MISSE-12 and MISSE-15 missions, and the PCE-4 flown as part of the MISSE-13 mission. The PCE 1-4 flight samples were flown in either ram, wake, zenith or nadir flight orientations. The primary objectives of the PCE 1-4 experiments are to determine the LEO atomic oxygen (AO) erosion yield, Ey (volume loss per incident oxygen atom) and radiation durability of spacecraft polymers, composites and coatings. In addition, each experiment has a wide variety of materials with numerous sample objectives. This presentation provides an overview of the PCE 1-4 experiments, the numerous sample collaborators, the space environmental exposure of the flight samples, and an overview of the post-flight observations and results. The results include AO fluence and contamination analyses for each mission flight orientation, erosion data for the PCE 1-4 AO Ey samples, optical property data, and tensile results for the MISSE-9 and MISSE-13 tensile samples. In addition, an introduction of results from other unique samples such as indium tin oxide (ITO) coated thermal control samples, shape memory polymer composites, melanin based composites, and specialty coatings, will be provided.

Atomic oxygen↗