Search NASA⌕ Search

SEARCH · Search NASA

Results for “Prepreg”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

461 records · Page 26

Tensile Behavior and High-Cycle Fatigue Durability of a SiC/SiC Ceramic-Matrix Composite Without and With Simulated Cooling Holes

High-cycle fatigue (HCF) behavior of a melt-infiltrated, prepreg SiC/SiC composite was investigated using specimens without and with simulated cooling holes at 816 and 1,316 °C. The ceramic-matrix composite (CMC) material used for this study was fabricated by GE Aviation and had a ply configuration of [0/90/0] 3 . HCF tests were conducted with an R-ratio of 0.6 and a cyclic frequency of 30 Hz. Maximum tensile gross-section stresses used in the HCF tests ranged from 152 to 359 MPa. Runout in HCF was defined as 30 million cycles (278 h) at both temperatures. Monotonic tensile tests were conducted at room temperature (RT) on as-received CMC specimens and on HCF runout specimens without and with holes to determine residual tensile strengths. Digital image correlation (DIC) and acoustic emission (AE) techniques were used to monitor progression of damage in RT tensile tests on specimens without and with holes. Fractography was performed on a limited number of specimens without and with holes to determine morphology of fracture surfaces. Representative RT stress-strain behavior, elevated temperature HCF behavior at the two temperatures, and RT residual tensile strengths of HCF runout specimens are documented in this report. Select examples of DIC and AE data from RT tensile tests on specimens without and with holes and typical features observed on fracture surfaces of specimens tested under tensile and HCF conditions are also discussed.

Ceramic matrix composite↗

Thermal Conductivity and Mechanical Properties of Epoxy Composites With Hybridized PAN- and Pitch-Based Fiber Architecture

A series of hybrid polyacrylonitrile- (PAN-) and pitch-based carbon fiber/epoxy composites were fabricated and tested to evaluate the influence of hybrid fiber configurations on composite strength, modulus, and through-thickness thermal conductivity. Two grades of pitch-based fiber were selected based on their thermal conductivity: YSH-60A and YSH-80A from Nippon Graphite. These pitch-based fibers were received in tow form and as plain weave to allow flexibility in the architecture of the multifiber laminate. Two hybridization approaches were followed: (1) interleave of pitch-based fiber weave within braided PAN/epoxy prepreg and (2) incorporation of pitch-based fiber tows within a three-dimensional braided preform. These showed considerable impact on overall composite mechanical properties and through-thickness thermal conductivity.

Polymer Composite↗

Flexural Fatigue Testing and Qualification of Hybrid PAN-pitch Composite Materials with High Through-Thickness Thermal Conductivity

Carbon-fiber-reinforced polymers (CFRPs) considered for motor components within future electric vertical takeoff and landing (eVTOL) vehicles require not only a high strength-to-weight ratio but also a high through-thickness thermal conductivity (TC) to dissipate heat. Previously, CFRPs incorporating pitch CF interleaves demonstrated an increased through-thickness TC relative to the baseline composite, but the effect on flexural fatigue life was not evaluated. For this work, T700S/TC275–1 braided carbon fiber/epoxy prepreg baseline (no interleave), YSH–60A pitch interleave, and YS–80A pitch interleave configurations were tested for fatigue life. A combination of ASTM International Standards D7264 and D3479 were used to develop a reliable testing method. An Instron® (Illinois Tool Works Inc.) 8501 servohydraulic system with a fatigue test fixture was set up with a 16:1 span:thickness ratio, load ratio R set to 0.1, and frequency of 4 Hz. High-cycle fatigue testing was completed, and it was found that YSH–60A interleave performed slightly better than YS–80A below 100,000 cycles but showed no differences above 100,000 cycles. In all cases, the baseline CFRP had superior fatigue life performance both in terms of stress handled and total cycles to failure. These fatigue testing data will inform future use of hybrid CFRP materials by highlighting the tradeoff between increased through-thickness TC and fatigue life. Testing guidelines, equipment, and parameters for static and fatigue tests were successfully outlined for CFRPs.

composites↗

Advances in Thermoplastic Composites Over Three Decades – A Literature Review

Recently, there has been a renewed interest in thermoplastic composites driven mainly by advances in automation which can lead to significant cost reductions by increasing manufacturing rates while simultaneously reducing the part count and energy consumption relative to the manufacturing of thermoset composites. At the same time, new material systems have been developed and the thermoplastic composites prepreg material quality has improved over time. Additionally, thermoplastic composites have nearly infinite room-temperature shelf life and production scraps can be reused and retired parts can be recycled, providing opportunities for more sustainable operations and downstream markets. These factors have contributed to a strong interest in advancing thermoplastic composites for aerospace, automotive, and other industrial applications. The objective of the present study is to assess the state of the art regarding the maturity and performance of thermoplastic composite materials and to document the advances made in manufacturing and assembly of thermoplastic composite structures. Therefore, more than 200 NASA reports, conference proceedings and journal papers spanning three and a half decades (1986-2022) were reviewed and the findings summarized. The current study, however, is limited in scope with a focus on the application of thermoplastic composites to aircraft structures. Further, the study does not provide a comprehensive assessment of the available literature but rather offers an overview of past and present research being conducted in the field of thermoplastic composites. The information provided may be used to identify gaps and help guide future research and development. In this report, the opportunities offered by the use of thermoplastic composites in general and challenges encountered in particular are presented first. Second, an overview of thermoplastic materials is presented, manufacturing methods are discussed, and new methods for fastener-less assembly such as welding are introduced. Third, tests that have been performed on different levels of the building block, ranging from coupon to structural level, are presented. In particular, fracture toughness results for different thermoplastic composite materials are used to demonstrate their performance compared to state-of-the-art thermoset composites. Fourth, several examples of analyses are discussed including process modelling and progressive damage analysis (PDA). An extensive list of references and appendices with tables support the narrative. Lastly, a brief summary with outlook and recommendations for future research is provided.

composites↗

Offset-Stoichiometric Reflowable Composite Bonding Method with Adhesive for Mitigating Strict Faying Surface Tolerances

Inherent susceptibility of adhesive bonds to miniscule quantities of contamination can cause undetectable weakened bonds. For this reason, the Federal Aviation Administration (FAA) places strict regulations on adhesively bonded joints in primary aircraft structures. To meet certification requirements aircraft manufactures resort to redundant load paths in the form of fasteners which inherently add weight to the structure and increase manufacturing time. In prior work, a secondary bonding technique called AERoBOND was developed, which utilized off-stoichiometric epoxymatrix resins to facilitate reflow and diffusion of the resin within the joint interface during a secondary bonding/cure process, thus achieving a bond similar to a co-cured joint. However, the AERoBOND process required tight spatial tolerances between the two parts being joined. This study examined the utilization of conventional adhesive with the AERoBOND method to act as a filler in the joint line, effectively reducing the need for tight tolerances on the joining parts and serving as a flexible alternative for existing manufacturing processes. Ultrasonic inspection, optical microscopy, and ASTM International standard tests were performed to analyze the joints for defects and to quantify the mode-I and mode-II interlaminar fracture toughness and short beam strength of the proposed methodology with varying manufacturing parameters. The comprehensive results indicate that the AERoBOND+ method with and without surface preparation performs comparably to co-cured and conventional, adhesively bonded joints when secondary cured in an autoclave with 791 kPa of pressure. As an example, the AERoBOND+ panel without surface preparation bonded with 791 kPa of pressure (referred to as AB+3 throughout paper) had a mode-I fracture toughness (G Ic ) of 0.643 kJ/m 2 and a mode-II fracture toughness (G IIc ) of 4.000 kJ/m 2 in the non-precracked condition and 4.218 kJ/m 2 in the precracked condition at the adhesive-to-prepreg interface. These results were 96%, 142%, and 217%, respectively, of a co-cured baseline panel (referred to as C1 throughout paper).

Composites↗

An Evaluation of Composite Primary Structure for Habitat Modules

Boeing studied the use of composite structures in deep space habitats. Compared to metallic modules, composite structures offer increased strength and stiffness with reduced mass. The study evaluated the design considerations and the mass benefits of an all composite primary structure. The composite module design included a continuous pressure shell, composite longerons, and circumferential ring frames. The composite material selected was a high strength carbon fiber and epoxy slit tape prepreg. The manufacturing involved automated fiber placement and utilizing existing facilities and autoclaves. Analysis showed a 33% reduction in primary structure mass and an overall net reduction of nearly 1900 kg compared to metallic modules. The composite module demonstrated improved mass efficiency and opens new possibilities for mission performance in deep space exploration.

Composite↗

SURFACE MORPHOLOGY OF CARBON FIBER POLYMER COMPOSITES AFTER LASER STRUCTURING

The increasing use of Carbon Fiber Polymer Composite (CFPC) as a lightweight material in automotive and aerospace industries requires the control of surface morphology. In this study, the composites surface was prepared by ablating the resin in the top fiber layer of the composite using an Nd:YAG laser. The CFPC specimens with T700S carbon fiber and Prepreg - T83 resin (epoxy) were supplied by Plasan Carbon Composites, Inc. as 4 ply thick, 0/90o plaques. The effect of laser fluence, scanning speed, and wavelength was investigated to remove resin without an excessive damage of the fibers. In addition, resin ablation due to the power variation created by a laser interference technique is presented. Optical property measurements, optical micrographs, 3D imaging, and high-resolution optical profiler images were used to study the effect of the laser processing on the surface morphology.

Sabau, Adrian S↗

A LASER INTERFERENCE-BASED SURFACE TREATMENT OF AL AND CARBON FIBER POLYMER COMPOSITES FOR ENHANCED BONDING

Due to its increased use in the automotive and aerospace industries, joining of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) to metals demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using a new laser based technique, in which the laser interference power profile was created by splitting the beam and guiding those beams to the sample surface by overlapping each other with defined angles to each other. Results were presented for the overlap shear testing of single-lap joints made with Al 5182 and CFPC specimens whose surfaces prepared by (a) surface abrasion and solvent cleaning; and (b) laser-interference structured surfaces by rastering with a 4 mm laser beam at approximately 3.5 W power. CFPC specimens of T700S carbon fiber, Prepreg T70 epoxy, 4 or 5 ply thick, 0/90o plaques were used. Adhesive DP810 was used to bond Al and CFPC. The bondline was 0.25mm and the bond length was consistent among all joints produced. First, the effect of the laser speed on the joint performance was evaluated by laser-interference structure Al and CFPC surfaces with a beam angle of 3o and laser beam speeds of 3, 5, and 10 mm/s. For this sensitivity study, 3 joint specimens were used per each joint type. Based on the results for minimum, maximum, and mean values for the shear lap strength and maximum load for all the 9 joint types, two joint types were selected for further evaluations. Six additional joint specimens were prepared for these two joint types in order to obtain better statistics and the shear test data was presented for the range, mean, and standard deviation. The results for the single-lap shear tests obtained for six joint specimens, indicate that the shear lap strength, maximum load, and displacement at maximum load for those joints made with laser-interference structured surfaces were increased by approximately 14.8%, 16%, and 100%, respectively over those measured for the baseline joints.

Sabau, Adrian S↗

High-Speed Layup and Forming of Automotive Composite Components

This Project is focused on the design and manufacture of automotive components that meet functional and environmental requirements of an existing automotive application at a cost of ≤ $\$$11.00 per kilogram weight reduction. This project fosters the development of composite material technologies suitable for high volume automotive processes and run rates as well as industry workforce development with these technologies. Current automotive manufacturing involves utilizing steel or aluminum in sheet form which is rapidly stamped into components at rates up to 3600 per hour. The metallic sheets are available in many different thicknesses, strength levels, and manufacturing rates are reasonable independent of part size. While composite materials are available for use in automotive applications, the material cost, labor to manufacture and the processing of the waste far exceed the cost compared to metallic designs. Typical composite layer by layer layup procedures don’t meet the desired 60 second layup time that current automotive processes require and are also restricted by part size. Due to these factors, composites have not yet made advances into today’s high volume automotive applications. Industry partners DURA, BASF, Ford, and IACMI core innovation partner MSU collaborated to develop a manufacturing process technology that is capable of manufacturing composite blanks at high volume and independent of part size. IACMI core innovation partner Purdue provided FEA analysis and cost modelling. The objective of this project was to demonstrate a composite sheet layup and consolidation process that can be commercialized for high volume requirements, identify potential layup equipment suppliers, and develop a process of 60 second layup, forming, and trimming of a continuous fiber automotive component for the mainstream market.

42 ENGINEERING↗

Modified Epoxy Matrix Resins for Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination that can lead to weak bonds. No methods currently exist to measure the strength of an adhesive bond nondestructively. For these reasons, regulating organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to achieve certification for civil transport aircraft. To meet this requirement, manufacturers commonly install redundant fasteners (~105 fasteners in a twin-aisle airframe with composite fuselage and wings), which add tremendous complexity, time and cost, and significantly reduce performance of the airframe. Under NASA’s Convergent Aeronautics Solutions (CAS) Program, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy matrix resins to enable reflow and diffusion of the resin at the interface during a secondary bonding/cure process. The mixing process eliminates the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion across a nearly two-dimensional boundary. The AERoBOND interface is similar to the interlaminar region formed during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin, which can be measured, inspected non-destructively, and certified for flight with fewer redundant fasteners. This presentation describes the ongoing development of stoichiometrically-offset epoxy resins to control the degree of cure in composite joints and enable interfacial mixing during secondary bonding/curing. Details on the resin formulation, laminate fabrication, and mechanical testing will also be presented. The precracked mode-II fracture toughness measured from preliminary AERoBOND joints was similar for joints fabricated with conventional epoxy matrix materials.

thermoset, hardener, prepreg, assembly↗