Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pressure transducers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Shock Characteristics Measured Upstream of Both a Forward-Swept and an Aft-Swept Fan

Three different types of diagnostic data-blade surface flow visualization, shroud unsteady pressure, and laser Doppler velocimeter (LDV)--were obtained on two fans, one forward-swept and one aft-swept, in order to learn more about the shocks which propagate upstream of these rotors when they are operated at transonic tip speeds. Flow visualization data are presented for the forward-swept fan operating at 13831 rpm(sub c), and for the aft-swept fan operating at 12500 and 13831 rpm(sub c) (corresponding to tip rotational Mach numbers of 1.07 and 1.19, respectively). The flow visualization data identify where the shocks occur on the suction side of the rotor blades. These data show that at the takeoff speed, 13831 rpm(sub c), the shocks occurring in the tip region of the forward-swept fan are further downstream in the blade passage than with the aft-swept fan. Shroud unsteady pressure measurements were acquired using a linear array of 15 equally-spaced pressure transducers extending from two tip axial chords upstream to 0.8 tip axial chords downstream of the static position of the tip leading edge of each rotor. Such data are presented for each fan operating at one subsonic and five transonic tip speeds. The unsteady pressure data show relatively strong detached shocks propagating upstream of the aft-swept rotor at the three lowest transonic tip speeds, and weak, oblique pressure disturbances attached to the tip of the aft-swept fan at the two highest transonic tip speeds. The unsteady pressure measurements made with the forward-swept fan do not show strong shocks propagating upstream of that rotor at any of the tested speeds. A comparison of the forward-swept and aft-swept shroud unsteady pressure measurements indicates that at any given transonic speed the pressure disturbance just upstream of the tip of the forward-swept fan is much weaker than that of the aft-swept fan. The LDV data suggest that at 12500 and 13831 rpm(sub c), the forward-swept fan swallowed the passage shocks occurring in the tip region of the blades, whereas the aft-swept fan did not. Due to this difference, the flows just upstream of the two fans were found to be quite different at both of these transonic speeds. Nevertheless, despite distinct differences just upstream of the two rotors, the two fan flows were much more alike about one axial blade chord further upstream. As a result, the LDV data suggest that it is unwise to attempt to determine the effect that the shocks have on far field noise by focusing only on measurements (or CFD predictions) made very near the rotor. Instead, these data suggest that it is important to track the shocks throughout the inlet.

Podboy, Gary G.↗
NASA NTRS2015

Boundary Layer Instabilities Generated by Freestream Laser Perturbations

A controlled, laser-generated, freestream perturbation was created in the freestream of the Boeing/AFOSR Mach-6 Quiet Tunnel (BAM6QT). The freestream perturbation convected downstream in the Mach-6 wind tunnel to interact with a flared cone model. The geometry of the flared cone is a body of revolution bounded by a circular arc with a 3-meter radius. Fourteen PCB 132A31 pressure transducers were used to measure a wave packet generated in the cone boundary layer by the freestream perturbation. This wave packet grew large and became nonlinear before experiencing natural transition in quiet flow. Breakdown of this wave packet occurred when the amplitude of the pressure fluctuations was approximately 10% of the surface pressure for a nominally sharp nosetip. The initial amplitude of the second mode instability on the blunt flared cone is estimated to be on the order of 10 −6 times the freestream static pressure. The freestream laser-generated perturbation was positioned upstream of the model in three different configurations: on the centerline, offset from the centerline by 1.5 mm, and offset from the centerline by 3.0 mm. When the perturbation was offset from the centerline of a blunt flared cone, a larger wave packet was generated on the side toward which the perturbation was offset. The offset perturbation did not show as much of an effect on the wave packet on a sharp flared cone as it did on a blunt flared cone.

Chou, Amanda↗
NASA NTRS1972

A comparison of disturbance levels measured in hypersonic tunnels using a hot-wire anemometer and a pitot pressure probe.

Disturbance levels were measured in the test section of a Mach 5 blowdown jet using a constant-current, hot-wire anemometer and a pressure transducer. The disturbance levels, measured by the two instruments and normalized by local mean values, agreed within about 30%, with the pitot data higher than the hot-wire data. The rms disturbance levels measured with the hot-wire anemometer and converted to pitot pressures using a quasi-steady flow analysis, were about two-thirds the levels measured with the pitot probe. The variation of the normalized rms disturbance levels with stagnation pressure indicated that transition occurred in the boundary layer on the nozzle wall and influenced the outputs of the instruments located at the exit of the nozzle when the total pressure was about 35 N/sq cm. Below this pressure the disturbance levels decreased markedly. At higher pressures the disturbances were predominantly aerodynamic noise generated by the turbulent boundary layer on the nozzle wall.

Stainback, P. C.↗
NASA NTRS1984

Research pressure instrumentation for NASA Space Shuttle main engine

The development of prototype pressure transducers which are targeted to meet the Space Shuttle Main Engine SSME performance design goals is discussed. The fabrication, testing and delivery of 10 prototype units is examined. Silicon piezoresistive strain sensing technology is used to achieve the objectives of advanced state-of-the-art pressure sensors in terms of reliability, accuracy and ease of manufacture. Integration of multiple functions on a single chip is the key attribute of this technology.

Anderson, P. J.↗
NASA NTRS1984

Research pressure instrumentation for NASA Space Shuttle main engine, modification no. 5

The purpose of Modification No. 5 of this contract is to expand the scope of work (Task C) of this research study effort to develop pressure instrumentation for the SSME. The objective of this contract (Task C) is to direct Honeywell's Solid State Electronics Division's (SSED) extensive experience and expertise in solid state sensor technology to develop prototype pressure transducers which are targeted to meet the SSME performance design goals and to fabricate, test and deliver a total of 10 prototype units. SSED's basic approach is to effectively utilize the many advantages of silicon piezoresistive strain sensing technology to achieve the objectives of advanced state-of-the-art pressure sensors in terms of reliability, accuracy and ease of manufacture. More specifically, integration of multiple functions on a single chip is the key attribute of this technology which will be exploited during this research study.

Anderson, P. J.↗
NASA NTRS1984

SRB/FWC water impact: Flexible body loads test

The modeling of the cavity collapse pressure loading is discussed. There are excellent high speed color films of the quarter scale model during cavity collapse. In these films, it is possible to see a very clearly defined pressure wave front propagating circumferentially around the vehicle that seems to be associated at least on the lee side with an abrupt rise in pressure at each pressure transducer. By using a motion analyzer and stepping through the films, the location of this wave front is tracted at a number of time intervals for drops 17 through 21. The entry conditions and average wave front velocity are shown. Mathematical formulae aid in the reconstruction of the spatial distribution of the pressure.

Source record↗
NASA NTRS1993

Effect of wind tunnel acoustic modes on linear oscillating cascade aerodynamics

The aerodynamics of a biconvex airfoil cascade oscillating in torsion is investigated using the unsteady aerodynamic influence coefficient technique. For subsonic flow and reduced frequencies as large as 0.9, airfoil surface unsteady pressures resulting from oscillation of one of the airfoils are measured using flush-mounted high-frequency-response pressure transducers. The influence coefficient data are examined in detail and then used to predict the unsteady aerodynamics of a cascade oscillating at various interblade phase angles. These results are correlated with experimental data obtained in the traveling-wave mode of oscillation and linearized analysis predictions. It is found that the unsteady pressure disturbances created by an oscillating airfoil excite wind tunnel acoustic modes which have detrimental effects on the experimental data. Acoustic treatment is proposed to rectify this problem.

Buffum, Daniel H.↗
NASA NTRS1994

Effect of wind tunnel acoustic modes on linear oscillating cascade aerodynamics

The aerodynamics of a biconvex airfoil cascade oscillating in torsion is investigated using the unsteady aerodynamic influence coefficient technique. For subsonic flow and reduced frequencies as large as 0.9, airfoil surface unsteady pressures resulting from oscillation of one of the airfoils are measured using flush-mounted high-frequency-response pressure transducers. The influence coefficient data are examined in detail and then used to predict the unsteady aerodynamics of a cascade oscillating at various interblade phase angles. These results are correlated with experimental data obtained in the traveling-wave mode of oscillation and linearized analysis predictions. It is found that the unsteady pressure disturbances created by an oscillating airfoil excite wind tunnel acoustic modes, which have detrimental effects on the experimental results. Acoustic treatment is proposed to rectify this problem.

Buffum, D. H.↗
NASA NTRS1988

Experimental study of unsteadiness of the flow around an ogive-cylinder at incidence

Flow visualization, surface mounted pressure transducers and hot-wires anemometers have been used to measure the leeside vortex flowfield on an ogive-cylinder at high angles of attack. The results show that there is a high degree of flowfield unsteadiness which arises due to several phenomena. The phenomena include large scale von Karman-type shedding, high frequency pressure and velocity fluctuations indicative of the presence of free shear-layer vortices, and a vortex interaction. The effects of position along the body, angle of attack and wind tunnel speed on the surface pressure and velocity in the wake have been investigated.

Degani, D.↗
NASA NTRS1990

A study of the unsteadiness of crossing shock wave turbulent boundary layer interactions

The unsteadiness of crossing shock wave turbulent boundary layer interactions at a nominal Mach number of 3 was examined by measuring wall pressure fluctuations using multiple, high frequency response, pressure transducers. The unsteadiness in the initial part of the interaction for all the interactions is similar to that of single fin interaction as studied by Tran and Bogdonoff (1987). However, for stronger interactions, flow downstream of the inviscid shock crossing position has a significant unsteady characteristic. In this unsteady region of the interaction, mean surface pressure rises significantly over the value obtained from the inviscid shock approximation. The energy spectrum of the fluctuating pressure signal shows a significant increase in the energy level at the higher frequencies.

Poddar, K.↗
NASA NTRS2025

Subsonic Ultra Green Aircraft Research: Phase V – Buffet Test Report

This test report summarizes work performed by the Boeing Subsonic Ultra-Green Aircraft Research (SUGAR) team in the Phase V Transonic Truss-Braced Wing contract task. The task was awarded in September 2020, and ended at the end of September 2022. As a part of the SUGAR Phase V contract task, Boeing developed a wind tunnel test plan, model requirements, then fabricated and conducted a dedicated transonic buffet wind tunnel test. The test focused on the investigation of buffet onset, and the ability to accurately predict buffet onset for the TTBW configuration. This report summarizes the results and post-test analysis of the 9% scale, semispan, Transonic Truss-Braced Wing (TTBW) transonic buffet model tested at the NASA Ames Research Center Unitary Plan Wind Tunnel (UPWT) 11-Foot Transonic Wind Tunnel (11-Ft TWT) facility located at Moffett Field, CA. It was tested from January 24, 2022, through February 18, 2022. The wind tunnel test was successful in capturing buffet onset at the model design dynamic pressure. Multiple configurations were tested starting in the wing-body-strut configuration and ending with the full configuration including wing-body-strut-nacelle/pylon, and flap hinge. The test also measured the effect of control surface deflections (ailerons and spoilers), as well as the effect of an outboard strut flap. Steady data collected during the test included standard force and moment measurements, as well as wing, strut, nacelle, and body (fuselage) static pressures. These data were collected in a standard pitch-pause mode. Unsteady data captured in the test, collected in continuous pitch mode, included wing and strut dynamic pressures, accelerations, and strains. According to test data, previous concerns regarding critical buffet onset on the strut (at low vehicle lift coefficient) and in the wing-strut channel have been mitigated. Buffet onset on the TTBW appears to follow conventional wing-induced buffet onset mechanisms. However, the critical station where buffet onset first occurs has moved inboard to the wing-strut juncture span location (55-60% span) from the typical ~70% span location. Test data obtained by unsteady pressure transducers provided a good match to expected buffet onset modes. An assessment of different tools and methodologies for predicting buffet onset was conducted. Reasonable agreement was found for buffet boundary predictions between most of the methods examined when using a forward trip location, with the greatest discrepancies from the pitching moment break and trailing edge pressure divergence methods. When an aft trip location was used the buffet boundary predictions diverged more significantly from unsteady pressure measurements. In addition, good agreement between the buffet onset trends were found when the Reynolds number, configuration, or spanload was changed.

strut↗
NASA NTRSDate not supplied

Isolator Shock Train Response to Dual-Mode Scramjet Throttling-Like Forcing

Typical dual-mode scramjet designs employ an isolator component situated between the inlet and combustor. The isolator fluidically buffers the inlet from the combustor via the formation of a shock train, an interconnected series of shock-boundary layer interactions. The isolator is required during ramjet-engine operation and at the lower edges of the scramjet operational envelope. In an operational engine, transient behavior imposes fluidic dynamics due to attitude adjustments, combustor throttling, aberrant resonances within the combustor, etc. To accommodate these transients, the shock train adjusts on both temporal and spatial scales. Sufficiently large downstream pressure increases in the combustor play a critical role during unstart, whereby strong compression waves propagate upstream in the isolator to ultimately force the shock train out the inlet, if it cannot stabilize to the pressure increase. This critically reduces the engine mass flow rate, potentially causing a catastrophic reduction in thrust and loss of the vehicle. A nearly instantaneous unstart can, in principle, be predicted by a ratio of the normal shock pressure jump in an inviscid isolator. However, lower-magnitude perturbations, below this bound, also induce unstarts. Understanding the transient behavior inherent in unsteady isolator operation is critical to reducing safety margin in isolator length and refining engine control algorithms to improve engine performance. The Isolator Dynamics Research Lab (IDRL) is a cold-flow, direct-connect isolator facility ideal for assessing the fundamental fluid dynamics of shock trains. The internal flow of a scramjet isolator is modeled using a 2D, symmetric Mach 2.5 nozzle followed by a 695 mm long, 25.4x50.8 mm rectangular isolator test section. A blockage cone on a high-speed ball screw actuator downstream of the isolator is pulsed to simulate the throttling behavior in an operational combustor. Wall flush high-speed static pressure transducers detect the streamwise shock train within the isolator. Time delays between the onset of the throttling and the response motion of the shock train are analyzed to assess the controlling scales and parameters. From this analysis, the response time of the isolator shock train system is found to depend primarily on the isolator back pressure time-rate-of-change but quickly saturates to a maximum propagation speed along the isolator. These results inform dual-mode scramjet engine designers of the critical parameters and limits of an unstart resistant engine.

scramjet↗
NASA NTRS1988

A miniature, infrared pressure telemetry system

A miniature, single-channel, infrared telemetry system designed for making base pressure measurements on a wind tunnel model has been developed for the 13-inch magnetic suspension and balance system (MSBS) at Langley Research Center. The system consists of a transmitter installed in the wind tunnel model and a receiver station located outside of the test section. The onboard transmitter package includes a miniature pressure transducer, a signal conditioning circuit, and IR LED and a hearing-aid battery package. The IR LED, which is mounted flush with the model's surface, serves as the transmitter. The system is automatically activated in a magnetic field and has low power requirements. The system has been successfully employed to make low speed base pressure measurements at the 13-inch MSBS. The battery powered telemetry transmitter has a demonstrated one-hour operating life and an overall precision of better than 1/2 percent full scale.

Tcheng, Ping↗
NASA NTRS1986

An electronic scanner of pressure for wind tunnel models

An electronic scanner of pressure (ESOP) has been developed by NASA Ames Research Center for installation in wind tunnel models. An ESOP system consists of up to 20 pressure modules (PMs), each with 48 pressure transducers and a heater, an analog-to-digital (A/D) converter module, a microprocessor, a data controller, a monitor unit, a control and processing unit, and a heater controller. The PMs and the A/D converter module are sized to be installed in the models tested in the Ames Aerodynamics Division wind tunnels. A unique feature of the pressure module is the lack of moving parts such as a pneumatic switch used in other systems for in situ calibrations. This paper describes the ESOP system and the results of the initial testing of the system. The initial results indicate the system meets the original design goal of 0.15 percent accuracy.

Kauffman, Ronald C.↗
NASA NTRS1993

Full-Scale Wind Tunnel Studies of F/A-18 Tail Buffet

Tail buffet studies were conducted on a full-scale, production, F/A-18, fighter aircraft in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center in Moffett Field, California. The F/A-18 was tested over an angle-of-attack range of 18deg to 50deg, a side-slip range of -15deg to 15deg, and at wind speeds of up to 100 knots. The maximum speed corresponds to a Reynolds number of 12.3 x 10(exp 6) based on mean aerodynamic chord and a Mach number of 0.15. The port, vertical tail fin was instrumented with thirty-two surface pressure transducers, arranged in four by four arrays on both sides on the fin. The aircraft was also equipped with a removable Leading Edge eXtension (LEX) fence that is used on F/A-18 aircraft to reduce tail buffet loads. Time-averaged, power-spectral analysis results are presented for the tail fin bending moment derived from the integrated pressure field. The results are only for the zero side-slip condition, both with and without the LEX fence. The LEX fence significantly reduces the magnitude of the root-mean-square pressures and bending moments. Scaling issues are addressed by comparing full-scale results for pressures at the 60%-span and 45%-chord location with published results of small-scale, F/A-18 tail-buffet tests. The comparison shows that the tail buffet frequency scales very well with length and velocity. Root-mean-square pressures and power spectra do not scale as well. The LEX fence is shown to reduce tail buffet loads at all model scales.

Meyn, Larry A.↗
NASA NTRSDate not supplied

Evaluation of Silicon Carbide Pressure Sensor in Turbofan Engine Core Exhaust Nozzle

We report the results of the evaluation of single crystal 4H-silicon carbide piezoresistive pressure sensors that were directly inserted at the compressor and core exhaust nozzle exits, in shear contact with the engine-internal flow streams of the NASA DGEN Aeropropulsion Research Turbofan, where the operating temperatures at maximum power were ~230 oC, and ~460 oC, respectively. In addition to demonstrating sensor survivability during this maiden test, the frequency responses of the silicon-carbide sensors at the core-nozzle exit were compared against industry-standard silicon-based piezoresistive pressure transducers that externally placed, using an infinite-tube-probe arrangement. The low-voltage output of these early-development SiC sensors limited the frequency range with an acceptable signal-to-noise-ratio for the current application to less than about 2,500 Hz. The low output of the SiC sensors were due to a conservative burst-pressure diaphragm design that can be optimized to increase the frequency range. The results from this initial campaign offered insights to aspects of the sensor that would require further improvement, with the goal of achieving full-bandwidth capture of engine unsteady pressure fluctuations by direct interrogation of the flow field in hostile-environment engine-core components.

Silicon Carbide↗
NASA NTRSDate not supplied

Evaluation of SiC Pressure Sensors in Turbofan Engine Core Exhaust Nozzle

We report the results of the evaluation of single crystal 4H-silicon carbide piezoresistive pressure sensors that were directly inserted at the compressor and core exhaust nozzle exits, in shear contact with the engine-internal flow streams of the NASA DGEN Aeropropulsion Research Turbofan, where the operating temperatures at maximum power were ~230°C, and ~460°C, respectively. In addition to demonstrating sensor survivability during this maiden test, the frequency responses of the silicon-carbide sensors at the core-nozzle exit were compared against industry-standard silicon-based piezoresistive pressure transducers that externally placed, using an infinite-tube-probe arrangement. The low-voltage output of these early-development SiC sensors limited the frequency range with an acceptable signal-to-noise-ratio for the current application to less than about 2,500 Hz. The low output of the SiC sensors were due to a conservative burst-pressure diaphragm design that can be optimized to increase the frequency range. The results from this initial campaign offered insights to aspects of the sensor that would require further improvement, with the goal of achieving full-bandwidth capture of engine unsteady pressure fluctuations by direct interrogation of the flow field in hostile-environment engine-core components.

Silicon Carbide↗
NASA NTRS1998

Evaluation of Gritting Strategies for High Angle of Attack Using Wind Tunnel and Flight Test Data for the F/A-18

A subsonic study of high-angle-of-attack gritting strategies was undertaken with a 0.06-scale model of the F/A-18, which was assumed to be typical of airplanes with smooth-sided forebodies. This study was conducted in the Langley 7- by 10-Foot High-Speed Tunnel and was intended to more accurately simulate flight boundary layer characteristics on the model in the wind tunnel than would be possible by using classical, low-angle-of-attack gritting on the fuselage. Six-component force and moment data were taken with an internally mounted strain-gauge balance, while pressure data were acquired by using electronically scanned pressure transducers. Data were taken at zero sideslip over an angle-of-attack range from 0 deg to 40 deg and, at selected angles of attack, over sideslip angles from -10 deg to 10 deg. Free-stream Mach number was fixed at 0.30, which resulted in a Reynolds number, based on mean aerodynamic chord, of 1.4 x 10(exp 6). Pressure data measured over the forebody and leading-edge extensions are compared to similar pressure data taken by a related NASA flight research program by using a specially instrumented F/A-18, the High-Alpha Research Vehicle (HARV). Preliminary guidelines for high-angle-of-attack gritting strategies are given.

Hall, Robert M.↗